共查询到20条相似文献，搜索用时 15 毫秒
1.
A catastrophic debris flow in the Wenchuan Earthquake area,July 2013: characteristics,formation, and risk reduction 总被引：2，自引：1，他引：1
In the Wenchuan Earthquake area,many co-seismic landslides formed blocking-dams in debris flow channels. This blocking and bursting of landslide dams amplifies the debris flow scale and results in severe catastrophes. The catastrophic debris flow that occurred in Qipan gully(Wenchuan,Southwest China) on July 11,2013 was caused by intense rainfall and upstream cascading bursting of landslide dams. To gain an understanding of the processes of dam bursting and subsequent debris flow scale amplification effect,we attempted to estimate the bursting debris flow peak discharges along the main gully and analyzed the scale amplification process. The results showed that the antecedent and triggering rainfalls for 11 July debris flow event were 88.0 mm and 21.6 mm,respectively. The event highlights the fact that lower rainfall intensity can trigger debris flows after the earthquake. Calculations of the debris flow peak discharge showed that the peak discharges after the dams-bursting were 1.17–1.69 times greater than the upstream peak discharge. The peak discharge at the gully outlet reached 2553 m~3/s which was amplified by 4.76 times in comparison with the initial peak discharge in the upstream. To mitigate debris flow disasters,a new drainage channel with a trapezoidal V-shaped cross section was proposed. The characteristic lengths(h1 and h2) under optimal hydraulic conditions were calculated as 4.50 m and 0.90 m,respectively. 相似文献
2.
Flooding is the most prevalent and costly natural disaster in the world and building reservoirs is one of the major structural measures for flood control and management. In this paper, a framework was proposed to evaluate functions of reservoirs′ locations and magnitudes on daily peak flow attenuation for a large basin of China, namely Ganjiang River Basin. In this study, the Xinanjiang model was adopted to simulate inflows of the reservoirs and flood hydrographs of all sub-catchments of the basin, and simple reservoir operation rules were established for calculating outflows of the reservoirs. Four reservoirs scenarios were established to analyze reservoirs′ locations on daily peak flow attenuation. The results showed that: 1) reservoirs attenuated the peak discharges for all simulated floods, when the flood storage capacities increase as new reservoirs were built, the peak discharge attenuation by reservoirs showed an increasing tendency both in absolute and relative measures; 2) reservoirs attenuated more peak discharge relatively for small floods than for large ones; 3) reservoirs reduced the peak discharge more efficiently for the floods with single peak or multi peaks with main peak occurred first; and 4) effect of upstream reservoirs on peak attenuation decreased from upper reaches to lower reaches; upstream and midstream reservoirs played important roles in decreasing peak discharge both at middle and lower reaches, and downstream reservoirs had less effect on large peak discharge attenuation at outlet of the basin. The proposed framework of evaluating functions of multiple reservoirs′ storage capacities and locations on peak attenuation is valuable for flood control planning and management at basin scale. 相似文献
3.
Extreme Rainfall Events and Associated Natural Hazards in Alaknanda Valley, Indian Himalayan Region 总被引：2，自引：0，他引：2
JOSHI Varun KUMAR Kireet 《山地科学学报》2006,3(3):228-236
Introduction The Himalaya is considered to be the youngest mountains on the earth, and is tectonically very active, and hence inherently (geologically) vulnerable to hazards. Extreme rainfall events, landslides, debris flows, torrents and flash floods due… 相似文献
4.
Stability analysis of the dam is important for disaster prevention and reduction. The dam＇s geometry plays an important role in understanding its stability. This study develops a rapid landslide dam geometry assessment method for both earthquake-induced and rainfall-induced landslide dams based on nine real cases collected in Chinese Taipei and 214 cases collected worldwide. For simplification purposes, a landslide dam is classified into triangular or trapezoidal. The rapid landslide dam geometry assessment method in this paper uses only satellite maps and the topographic maps to get landslide area, and then analyze the dam geometry. These maps are used to evaluate the area of the landslide and the slope of the river bed. Based on the evaluation information, the proposed method can calculate dam height, the length of the dam, and the angles of the dam in both upstream and downstream directions. These geometry parameters of a landslide dam provide important information for further dam stability analysis. The proposed methodology is applied to a real landslide dam case at Hsiaolin Village. The result shows that the proposed method can be used to assess the landslide dam geometry. 相似文献
5.
Tangjiashan landslide is a typical high-speed consequent landslide of medium-steep dip angle. This landslide triggered by earthquake took place in about semi-minute. The relative sliding displacement is 900 meters, so average sliding speed is about 30 meters per second. The longitudinal length of barrier dam which is formed by high-speed landslide along river is 803.4 meters; and maximum width crossing river is 611.8 meters. And its volume is estimated about 20.37 million steres. Through detailed geological investigation of the barrier dam, together with early geological information before earthquake, geological structures of the barrier dam and its stability of upstream and downstream slopes are studied when water level reaches different elevations in condition of continual after shocks with seismic intensity of 7 or 8 Richter scale. On this basis, dam-breaking mode of barrier dam is discussed deeply. Thereby, analytic results provide significant guidance and advices to front headquarters of Tangjiashan barrier dam, so that some proper engineering measures can be implemented and flood discharge can be carried out well. 相似文献
6.
The present study focuses on the breaching process and failure of barrier dams due to overtopping. In this work, a series of centrifugal model tests is presented to examine the failure mechanisms of landslide dams. Based on the experimental results, failure process and mechanism of barrier dam due to overtopping are analyzed and further verified by simulating the experimental overtopping failure process. The results indicate that the barrier dam will develop during the entire process of overtopping in the width direction, whereas the breach will cease to develop at an early stage in the depth direction because of the large particles that accumulate on the downstream slope. Moreover, headcut erosion can be clearly observed in the first two stages of overtopping, and coarsening on the downstream slope occurs in the last stage of overtopping. Thus, the bottom part of the barrier dam can survive after dam breaching and full dam failure becomes relatively rare for a barrier dam. Furthermore, the remaining breach would be smaller than that of a homogeneous cohesive dam under the same conditions. 相似文献
7.
Based on the large-scale model tests, a simplified dam breach model for homogeneous cohesive dam due to overtopping failure is put forward. The model considers headcut erosion as one of the key homogeneous cohesive dam breaching mechanisms and we calculate the time-averaged headcut migration rate using an energy-based empirical formula. A numerical method is adopted to determine the initial scour position at the downstream slope in terms of the water head and dam height, and the broad-crested weir equation is utilized to simulate the breach flow. The limit equilibrium method is used to analyze the stability of breach slope during the breach process. An iterative method is developed to simulate the coupling process of soil and water at each time step. The calculated results of three dam breach cases testify the reasonability of the model, and the sensitivity studies of soil erodibility show that sensitivity is dependent on each test case’s soil conditions. In addition, three typical dam breach models, NWS BREACH, WinDAM B, and HR BREACH, are also chosen to compare with the proposed model. It is found that NWS BREACH may have large errors for cohesive dams, since it uses a noncohesive sediment transport model and does not consider headcut erosion, WinDAM B and HR BREACH consider headcut erosion as the breaching mechanism and handle well homogeneous cohesive dam overtopping failure, but overall, the proposed model has the best performance. 相似文献
8.
Yan Yan Peng Cui Su-chin Chen Xiao-qing Chen Hua-yong Chen Yi-liang Chien 《山地科学学报》2017,14(2):219-236
Outburst floods caused by breaches of landslide dams may cause serious damages and loss of lives in downstream areas; for this reason the study of the dynamic of the process is of particular interest for hazard and risk assessment. In this paper we report a field-scale landslide dam failure experiment conducted in Nantou County, in the central of Taiwan.The seismic signal generated during the dam failure was monitored using a broadband seismometer and the signal was used to study the dam failure process.We used the short-time Fourier transform(STFT) to obtain the time–frequency characteristics of the signal and analyzed the correlation between the power spectrum density(PSD) of the signal and the water level. The results indicate that the seismic signal generated during the process consisted of three components: a low-frequency band(0–1.5 Hz), an intermediate-frequency band(1.5–10 Hz) and a highfrequency band(10–45 Hz). We obtained the characteristics of each frequency band and the variations of the signal in various stages of the landslide dam failure process. We determined the cause for the signal changes in each frequency band and its relationship with the dam failure process. The PSD sediment flux estimation model was used to interpret the causes of variations in the signal energy before the dam failure and the clockwise hysteresis during the failure. Our results show that the seismic signal reflects the physical characteristics of the landslide dam failure process. The method and equipment used in this study may be used to monitor landslide dams and providing early warnings for dam failures. 相似文献
9.
The erosion and delivery processes of mine waste accumulations were reproduced through flume tests under 13 different experimental condition sets. Analysis of the flume test results showed that different scale model landslides, induced by the incision of mine waste accumulations, slipped into the channel and caused complete or partial blockages, with 28 complete blockages and 122 partial blockages observed during the flume tests. The failure of these temporary landslide dams amplified the peak discharge significantly, with the amplification more obvious when caused by the failure of a complete blockage compared to a partial blockage under the same experimental conditions. In order to explore the threshold conditions of a complete blockage, a new blockage index(Ibs) was developed to represent the degree of blockage. It was found that the threshold value of the blockage index for a complete blockage was around Ibs=4.0. What's more, there was a significant negative correlation between the blockage index and the amplification coefficient of peak discharge caused by the failure of a landslide dam.These preliminary results are intended to provide a scientific basis for future research on the disaster prevention and mitigation of mine waste debris flows, as the processes and mechanisms underlying the erosion and delivery of mine waste accumulations by upstream flows along a gully have not yet been clearly identified. 相似文献
10.
滑坡是形成堰塞坝的最主要原因,在地震、降雨、冰雪融水等作用下均可形成滑坡堰塞坝,而滑坡堰塞坝的堆积形态、范围等对评价堰塞坝的稳定性有着重要的影响。通过离散元方法(DEM),系统分析了三维条件下滑动距离、滑面出口宽度、滑面倾角、河床倾角、河谷形状对堰塞坝堆积形态的影响。研究结果表明:滑动距离和出口宽度对坝体高度影响最大;随出口宽度和坡面倾角的增加,坝长和坝宽分别呈线性增大和减小趋势;滑动距离可以有效控制滑体速度,进而影响堆积角大小;河床倾角主要影响坝长;对坝高、坝长、上下游绝对倾角正切值和堆积角正切值进行回归分析表明,数学模型契合程度高,说明其形态可以预测;引入2个参数λ和χ,对堰塞坝堆积特征进行了描述;河谷形状的影响主要体现在随着河谷底部宽度的增大,滑体爬高爬坡能力增强。研究成果对根据实际地形预测滑坡堰塞坝堆积形态进而评估坝体的安全性具有重要意义,可以为进一步开展堰塞湖溃决研究提供一定的参考。 相似文献
11.
Hongxing reservoir was constructed on the floodplain of Hulan River in Heilongjiang. The geological problem of the reservoir is the seepage of the dam base and its related seepage stability. The leakage of the reservoir is caused by the water head differences between the upstream and downstream of the dam. Severe seepage could decrease the engineering benefits of the reservoir. Moreover, infiltration function of water will influence the safety of the dam. Through the analysis on the granule constitute and the formation of the dam base, the types of the seepage failure apt to happen were defined and the anti-infiltration and the permissible depression ratio were determined. Using the numerical simulation software GMS, the two-dimension numerical modeling has been carried out to analyze the seepage field of the reservoir. Through the two conditions modeling with concrete impervious wall and no concrete impervious wall, the largest flow rate, single-wide seepage discharge and the max infiltration gradient of the dam base were calculated. According to the permeable depression ratio of the dam base, the seepage stability of Hongxing reservoir dam base was analyzed. 相似文献
12.
The erosion shape and the law of development of debris flow sabo dam downstream is a weak part in the study on debris flow erosion. The shape and development of scour pit have an important effect on the stability and safety of debris flow sabo dam, which determines the foundational depth of the dam and the design of protective measures downstream. Study on the scouring law of sabo dam downstream can evaluate the erosion range and reasonably arrange auxiliary protective engineering. Therefore, a series of flume experiments are carried out including different debris flow characteristics （density is varying from 1.5 t/m3 to 2.1 t/m~） and different gully longitudinal slopes. The result shows that the scour pit appears as an oval shape in a plane and deep in the middle while superficial at the ends in the longitudinal section, the position of the maximum depth point moves towards downstream with an increase of flume slope angle. The maximum depth of scour pit is mainly affected by the longitudinal slope of gully, density of debris flow, and the characteristics of gully composition （particle size and the viscosity of soil）. The result also indicates that the viscosity of soil will weaken the erosion extent. The interior slopes of scour pit are different between the upstream and the downstream, and the downstream slope is smaller than the upper one. For the viscous and non-viscous sands with the same distribution of gradation, the interior slope of non- viscous sand is smaller than the viscous sand.According to tbe regression analysis on the experimental data, the quantitative relationship between the interior slope of scour pit, slope of repose under water and the longitudinal slope of gully is established and it can be used to calculate the interior slope of scour pit. The results can provide the basis for the parameter design of the debris flow control engineering foundation. 相似文献
13.
The precision modeling of dam break floods can lead to formulation of proper emergency action plan to minimize flood impacts within the economic lifetime of the assets.Application of GIS techniques in integration with hydrological modeling for mapping of the flood inundated areas can play a momentous role in further minimizing the risk and likely damages.In the present study,dam break analysis using DAMBRK model was performed under various likely scenarios.Probable Maximum Flood (PMF)calculated for a return period of 1000 years using deterministic approach was adopted for dam break analysis of the proposed dam under various combinations of breach dimensions.The available downstream river cross-sections data sets were used as input in the model to generate the downstream flood profile.Dam break flow depths generated by the DAMBRK model under various combinations of structural failure are subsequently plotted on Digital Elevation Model(DEM)of the downstream of dam site to map the likely affected area.The simulation results reveals that in one particular case the flood without dam may be more intense if a rainfall of significant intensity takes place. 相似文献
14.
《山地科学学报》2015,(6)
Zonation patterns of riparian vegetation have been sampled and described in mountain streams in two catchments in the Hottentots-Holland Mountains, Western Cape, South Africa. Six main vegetation types that differ in structure and species composition, are dominant along these river banks: Aquatic vegetation, Wetbanks, Palmiet, Scrub, Forest and Shrubland(Fynbos). The study aims to correlate the vegetation patterns to flooding patterns, in particular the inundation frequency and stream power. A problem arises: because these catchments are ungauged, like most mountain catchments, with the only weirs at the downstream end of the catchment. Discharge data at the weirs are extrapolated to the sites upstream by multiplication with a factor based on the size of the subcatchment that drains through a sample site. In this way, recurrence intervals for floods in mountain streams are derived. Discharges at sites are also calculated using bed roughness(Manning's n) and slope in straight sections with uniform flow conditions. Stream power is derived from the discharges calculated in this manner. The combination of stream power and recurrence intervals explains the occurrence of most vegetation types occurring on the banks, except for one type: Afromontane Forest. This type is probably more dependent on other factors, such as protection from fire and the depth of the groundwater table. 相似文献
15.
ZHUANG Shuyu LI Guangjie CHEN Guoyu SHU Youfeng College of Construction Engineering Jilin University Changchun China 《东北亚地学研究》2009,(4):200-203
At present, the mechanism research on glacial lake outburst mainly focuses on the ice quake and ice landslide, etc. To some glacial lakes, the seepage deformation is the dominant factor in outburst process. Taking the Yindapu Glacial Lake in Tibet as an example, using SEEP/W module of FEM software （ GEO-STUDIO）, the authors analyzed seepage stability of terminal moraine ridge dam. The leading role of seepage deformation in some glacial lake outburst mechanism is proposed and proved. 相似文献
16.
At present, the mechanism research on glacial lake outburst mainly focuses on the ice quake and ice landslide, etc. To some glacial lakes, the seepage deformation is the dominant factor in outburst process. Taking the Yindapu Glacial Lake in Tibet as an example, using SEEP/W module of FEM software (GEO-STUDIO), the authors analyzed seepage stability of terminal moraine ridge dam. The leading role of seepage deformation in some glacial lake outburst mechanism is proposed and proved. 相似文献
17.
滑坡堰塞坝是由斜坡失稳堵塞河道而形成的天然坝体,且易溃坝诱发洪水,对沿岸群众生命财产构成巨大的威胁。为提升主动减灾防灾能力,急需构建了一种快速预测与判断滑坡堵江成坝能力的方法。通过文献资料查阅,结合遥感技术,提取了70处典型滑坡的地貌特征参数,其中50处为堵江成坝滑坡。运用K-S检验和M-W U检验方法分析了滑坡地貌特征因子的敏感性,利用Boruta算法确定了因子重要度,筛选了滑坡体积、面积、高差、长度及河宽共5个地貌特征参数。基于此,利用Bayes判别法与逻辑回归方法,分别建立了滑坡堰塞坝形成的预测模型,准确率超过90%。选取高重要度且差异显著的因子,利用比值法建立了滑坡堵江成坝阈值判据,实现了滑坡堰塞坝形成的快速判定。统计不同诱因下滑坡地貌特征,对比V-Wr经验公式,确定了滑坡堰塞坝形成与诱因间的关系,为进一步构建不同诱因下滑坡堰塞坝形成预测模型提供了技术支撑。 相似文献
18.
冰湖溃决灾害是指冰湖坝体突然破坏引发溃决洪水或溃决泥石流的现象,对下游人类活动和自然环境造成严重影响。近年来,藏东南地区冰川快速退缩,冰湖数量和规模显著增加,冰湖溃决事件广泛发生。基于1995-2021年多时相Landsat系列遥感影像、Sentinel-2A遥感影像,结合RAMMS水文动力学模型方法,对藏东南地区多依弄巴流域内冰湖、冰川进行动态变化分析,模拟冰崩危险体触发冰湖溃决和冰湖溃决泥石流的演进过程,根据泥石流模拟中的流速和流深对冰湖溃决可能影响的区域进行危险性分区。结果表明:流域内冰川面积由1995年的14.05 km2退缩为2021年的9.43 km2,年均退缩率约为0.15 km2/a。流域内共发育3处冰崩危险体,均可能触发冰湖溃决。潜在危险冰湖在全溃情况下,溃决泥石流会冲出沟口堵塞然乌湖湖口和帕隆藏布主河道,对下游居民和道路造成影响,影响范围约4.05 km2,其中高危险性区域约2.55 km2。危险性评价结果可为多依弄巴流域未来土地利用规划和防灾减灾提供依据,也能为藏东南地区冰湖溃决型泥石流危险评估提供参考。 相似文献
19.
Beam dams are a highly effective and commonly used open-type check dam in debris-flow hazard mitigation. In this study, dimensional analysis was used to obtain empirical equations for quantitatively determining the sediment-trapping and flow-regulating characteristics of a beam dam. To determine the coefficients of the empirical equations, flume experiments were conducted to simulate the trapping and regulating processes. The flow pattern, trapping, and regulating characteristics were investigated when debris flows passed through a beam dam. Debris-flow bulk density and peak discharge, and sediment-trapping ratios, were measured directly and indirectly. The results showed that three blocking actions occurred, and that blockage-breaking considerably influenced the trapping and regulating performance of the beam dam. The relative opening size and the sediment concentration were the two main factors affecting the performance of the beam dam. The ratio of trapping sediment decreased with relative opening, and increased with sediment concentration as well as reducing ratio of bulk density and reducing ratio of peak discharge. The sediment concentration and relative opening were the leading factors influencing the trapping and regulating sediment of a beam dam, followed by flume gradient. The results showed that the calculated values obtained using empirical equations were in good agreement with the values derived from the experiments, and that the deviation was acceptable. Finally, taking Zechawa Gully as an example, using the empirical equations we designed the opening size of a beam dam aimed to trap sediment and regulate peak discharge of debris flow in the main gully. 相似文献
20.
《山地科学学报》2019,(11)
Natural dams are formed when landslides are triggered by heavy rainfall during extreme weather events in the mountainous areas of Taiwan.During landslide debris movement, two processes occur simultaneously: the movement of landslide debris from a slope onto the riverbed and the erosion of the debris under the action of high-velocity river flow. When the rate of landslide deposition in a river channel is higher than the rate of landslide debris erosion by the river flow, the landslide forms a natural dam by blocking the river channel. In this study, the effects of the rates of river flow erosion and landslide deposition(termed the erosive capacity and depositional capacity, respectively) on the formation of natural dams are quantified using a physics-based approach and are tested using a scaled physical model.We define a dimensionless velocity index vde as the ratio between the depositional capacity of landslide debris(vd) and the erosive capacity of water flow(ve).The experimental test results show that a landslidedam forms when landslide debris moves at high velocity into a river channel where the river-flow velocity is low, that is, the dimensionless velocity index vde 54. Landslide debris will not have sufficient depositional capacity to block stream flow when the dimensionless velocity index vde 47. The depositional capacity of a landslide can be determined from the slope angle and the friction of the sliding surface, while the erosive capacity of a dam can be determined using river flow velocity and rainfall conditions. The methodology described in this paper was applied to seven landslide dams that formed in Taiwan on 8 August 2009 during Typhoon Morakot,the Tangjiashan landslide dam case, and the YingxiuWolong highway K24 landslide case. The dimensionless velocity index presented in this paper can be used before a rainstorm event occurs to determine if the formation of a landslide dam is possible. 相似文献