共查询到20条相似文献，搜索用时 15 毫秒
1.
Rill erosion processes on saturated soil slopes are important for understanding erosion hydrodynamics and determining the parameters of rill erosion models. Saturated soil slopes were innovatively created to investigate the rill erosion processes. Rill erosion processes on saturated soil slopes were modelled by using the sediment concentrations determined by sediment transport capacities (STCs) measurement and the sediment concentrations at different rill lengths. Laboratory experiments were performed under varying slope gradients (5°, 10°, 15°, and 20°) and unit-width flow rates (0.33, 0.67, and 1.33 × 10−3 m3 s−1 m−1) to measure sediment concentrations at different rill lengths (1, 2, 4, and 8 m) on saturated soil slopes. The measured sediment concentrations along saturated rills ranged from 134.54 to 1,064.47 kg/m3, and also increased exponentially with rill length similar to non-saturated rills. The model of the rill erosion process in non-saturated soil rills was applicable to that in saturated soil rills. However, the sediment concentration of the rill flow increased much faster, with the increase in rill length, to considerably higher levels at STCs. The saturated soil rills produced 120–560% more sediments than the non-saturated ones. Moreover, the former eroded remarkably faster in the beginning section of the rills, as compared with that on the non-saturated soil slopes. This dataset serves as the basis for determining the erosion parameters in the process-based erosion models on saturated soil slopes. 相似文献
2.
IntheLoessPlateau,alongtheslopelengthfromthetoptothebottom,soilerosionischaracterizedbyobviousverticalzonaldivision,thatis,sheeterosionzone,sheeterosionandrillerosionzone,rillerosionandshallowgullyerosionzoneandgullyerosionzone.Inthesheetandrillero..sionzone,rillerosionamounttakesup70%ofthetotalsoilloss[TANGKenetal.,1983,ZHENGFenlietal.,19871;intherillandshallowgullyerosionzone,rillerosionamountaccountsfor30--40%ofthetotalsoilloss.Sorillerosionisamajorerosionpatternonsteepslopeland.Riller… 相似文献
3.
On the basis of detailed rill surveys carried out on bare plots of different lengths at slopes of 12 per cent, basic rill parameters were derived. Rill width and maximum depth increased with plot length, whereas rill amount and cross‐sectional area, expressed per unit length, remained similar. On smaller plots, all rills were connected in a continuous transport system reaching the plot outlet, whilst on larger plots (10 and 20 m long) part of the rills ended with a deposition areas inside the plots. Amounts of erosion, calculated from rill volume and soil bulk density, were compared with soil loss measured at the plot outlets. On plots 10 and 20 m long, erosion estimated from volume of all rills was larger than measured soil loss. The latter was larger than erosion estimated from volume of contributing rills. To identify contributing soil loss area on these plots, two methods were applied: (i) ratio of total soil loss to maximum soil loss per unit area, and (ii) partition of plot area according to the ratio of contributing to total rill volume. Both methods resulted in similar areas of 21·8–23·5 m2 for the plot 10 m long and 31·2 m2 for the plot 20 m long. Identification of contributing areas enabled rill (5·9 kg m?2) and interrill (2·6 kg m?2) erosion rate to be calculated, the latter being very close to the value predicted from the Universal Soil Loss Equation. Although rill and interrill rates seemed to be similar on all plots, their ratio increased slightly with plot length. Application of this ratio to compute slope length factor of the Revised Universal Soil Loss Equation resulted in similar values to those predicted with the model. The achieved balance of soil loss suggested that all the sediment measured at the plot outlet originated from contributing rills and associated contributing rill areas. The results confirmed the utility of different plot lengths as a research tool for analysing the dynamic response of soil to rainfall–runoff. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
4.
Water flow velocity is an important hydraulic variable in hydrological and soil erosion models, and is greatly affected by freezing and thawing of the surface soil layer in cold high-altitude regions. The accurate measurement of rill flow velocity when impacted by the thawing process is critical to simulate runoff and sediment transport processes. In this study, an electrolyte tracer modelling method was used to measure rill flow velocity along a meadow soil slope at different thaw depths under simulated rainfall. Rill flow velocity was measured using four thawed soil depths (0, 1, 2 and 10 cm), four slope gradients (5°, 10°, 15° and 20°) and four rainfall intensities (30, 60, 90 and 120 mm·h−1). The results showed that the increase in thawed soil depth caused a decrease in rill flow velocity, whereby the rate of this decrease was also diminishing. Whilst the rill flow velocity was positively correlated with slope gradient and rainfall intensity, the response of rill flow velocity to these influencing factors varied with thawed soil depth. The mechanism by which thawed soil depth influenced rill flow velocity was attributed to the consumption of runoff energy, slope surface roughness, and the headcut effect. Rill flow velocity was modelled by thawed soil depth, slope gradient and rainfall intensity using an empirical function. This function predicted values that were in good agreement with the measured data. These results provide the foundation for a better understanding of the effect of thawed soil depth on slope hydrology, erosion and the parameterization scheme for hydrological and soil erosion models. 相似文献
5.
This paper reports the results of a field investigation aimed to establish morphological similarity between rills and ephemeral gullies. Rill measurements were made on 14 plots having a surface area of 22–352 m2 located on a 14·9% slope and on a plot 6·0 m wide and 22·0 m long having a uniform 22·0% slope. The plots are located on the experimental station for soil erosion measurements, ‘Sparacia’, of the Agricultural Faculty of Palermo University, in Sicily, Italy. All plots are subjected to natural rainfall. The measurements were made immediately following five events between November 2004 and December 2005. The ephemeral gully measurements were made on a cultivated area of about 120 ha, located in Central Sicily, which is representative of many soil‐crop conditions in the Mediterranean basin. The morphological similarity between rill and ephemeral gully was first tested. Then a power relationship between rill or gully volume and length, theoretically deduced by dimensional analysis and self‐similarity theory, was applied. This power relationship needs a different scale factor for rill and gully measurements. Finally, using two dimensionless groups representative of the channel morphology variables, the analysis showed that a single relationship can be applied to rill and gully measurements. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
6.
The erosion of hillslopes reclaimed following the surface-mining of coal is an important geomorphologic concern. However, progress in the design of post-mining topography and its hydrologic response has been hampered by the paucity of research focusing on the propensity of rill formation on these disturbed surfaces. This investigation is intended to partially rectify this situation through the development of regression equations for the prediction of rill frequency and magnitude based upon site characteristics. Rill width can be estimated using soil bulk density, hillslope age, and hillslope length with a standard error of 0.152 log10 units at this location. Rill depth can be estimated using soil shear strength, hillslope length, and hillslope age with a standard error of 0.114 log10 units. Rill length can be estimated using hillslope length, percent silt in the soil, hillslope age, Bouyoucos Clay Ratio, and soil bulk density with a standard error of 3.515 m. Rill frequency can be estimated using soil bulk density, Bouyoucos Clay Ratio, soil compaction, soil reaction (pH), and hillslope age with a standard error of 0.241 rills/m. The cross-product of rill width times depth can be estimated using soil shear strength, hillslope length, hillslope age, and soil bulk density with a standard error of 0.260 log10 units. These results must be tested further under various environmental conditions. Nevertheless, prediction of rill formation seems to be a problem capable of solution. 相似文献
7.
Effects of rainfall and slope on runoff,soil erosion and rill development: an experimental study using two loess soils 总被引：3，自引：0，他引：3 
下载免费PDF全文
下载免费PDF全文 Runoff generation and soil loss from slopes have been studied for decades, but the relationships among runoff, soil loss and rill development are still not well understood. In this paper, rainfall simulation experiments were conducted in two neighbouring plots (scale: 1 m by 5 m) with four varying slopes (17.6%, 26.8%, 36.4% and 46.6%) and two rainfall intensities (90 and 120 mm h?1) using two loess soils. Data on rill development were extracted from the digital elevation models by means of photogrammetry. The effects of rainfall intensity and slope gradient on runoff, soil loss and rill development were different for the two soils. The runoff and soil loss from the Anthrosol surface were generally higher than those from the Calcaric Cambisol surface. Higher rainfall intensity produced less runoff and more sediment for almost each treatment. With increasing slope gradient, the values of cumulative runoff and soil loss peaked, except for the treatments with 90 mm h?1 rainfall on the slopes with Anthrosol. With rainfall duration, runoff discharge decreased for Anthrosol and increased for Calcaric Cambisol for almost all the treatments. For both soils, sediment concentration was very high at the onset of rainfall and decreased quickly. Almost all the sediment concentrations increased on the 17.6% and 26.8% slopes and peaked on the 36.4% and 46.6% slopes. Sediment concentrations were higher on the Anthrosol slopes than on the Calcaric Cambisol slopes. At 90 mm h?1 rainfall intensity, increasingly denser rills appeared on the Anthrosol slope as the slope gradient increased, while only steep slopes (36.4% and 46.6%) developed rills for the Calcaric Cambisol soil. The contributions of rill erosion ranged from 36% to 62% of the cumulative soil losses for Anthrosol, while the maximum contribution of rill erosion to the cumulative soil loss was only 37.9% for Calcaric Cambisol. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
8.
In this paper the results of a field investigation on rilling carried out in the experimental Sparacia area are reported. The measurements were made on a plot 6 m wide and 22 m long subjected to natural rainfalls. For ten rainfalls the total soil loss (interrill and rill erosion) was collected in a storage system consisting of two tanks arranged in series at the base of the plot. Rill morphology (rill length and cross‐sections) was measured for five rainfall events, while the rill profile was surveyed for three events. First the contribution of each component (rill and interrill erosion) to total soil loss was established. Then the analysis allowed establishment of a power relationship between the rill length and the rill volume. Finally, for three events detailed information on rill erosion and rill morphology allowed verification of the applicability of WEPP and estimation of the rill erodibility constant. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
9.
Sediment delivery following post-fire logging is a concern relative to water quality. While studies have assessed the effect of post-fire logging on sediment yields at different spatial scales, none have explicitly identified sediment sources. Our goal was to quantify post-fire and post-salvage logging sediment yields and use rill patterns to identify sediment sources. We measured the extent and type of logging disturbance, length of rills per unit area or “rill density”, ground cover, and sediment yields in nine logged and five control small catchments or “swales”, 0.09 to 0.81 ha, for 5 years after the 2013 Rim Fire in California's Sierra Nevada. The logged swales had a mean ground disturbance of 31%. After the first wet season following logging, there was no difference in either mean rill density (0.071 and 0.088 m m−2, respectively) or mean transformed, normalized sediment yields between the control and logged swales. Untransformed mean sediment yields across three sites ranged from 0.11–11.8 and 1.1–3.2 Mg ha−1 for the controls and salvage-logged swales, respectively. Rill density was strongly related to sediment yield and increased significantly with the amount of high-traffic skid trail disturbance in logged swales. Rill density was not significantly related to the amount of bare soil despite a significant relationship between sediment yields and bare soil. Rills usually initiated in bare soil and frequently connected high traffic skid trails to the drainage network after being diverted by waterbars. Rill connectivity and sediment yields decreased in control and logged swales where vegetation or other surface cover was high, suggesting this cover disconnected rills from the drainage network. Increasing ground cover on skid trails and between areas disturbed by post-fire logging and stream channels may reduce sediment yields as well as the hydrologic connectivity between hillslopes and the drainage network. 相似文献
10.
The measurement and modelling of rill erosion at angle of repose slopes in mine spoil 总被引：2，自引：0，他引：2
The process of rill erosion causes significant amounts of sediment to be moved in both undisturbed and disturbed environments and can be a significant issue for agriculture as well as mining lands. Rills also often develop very quickly (from a single rainfall event to a season) and can develop into gullies if sufficient runoff is available to continue their development. This study examines the ability of a terrestrial laser scanner to quantify rills that have developed on fresh and homogeneous mine spoil on an angle of repose slope. It also examines the ability of the SIBERIA erosion model to simulate the rill's spatial and temporal behaviour. While there has been considerable work done examining rill erosion on rehabilitated mine sites and agricultural fields, little work has been done to examine rill development at angle of repose sites. Results show that while the overall hillslope morphology was captured by the laser scanner, with the morphology of the rills being broadly captured, the characteristics of the rills were not well defined. The digital elevation model created by the laser scanner failed to capture the rill thalwegs and tops of the banks, therefore delineating a series of ill defined longitudinal downslope depressions. These results demonstrate that an even greater density of points is needed to capture sufficient rill morphology. Nevertheless, SIBERIA simulations of the hillslope demonstrated that the model was able to capture rill behaviour in both space and time when correct model parameters were used. This result provides confidence in the SIBERIA model and its parameterization. The results demonstrate the sensitivity of the model to changes in parameters and the importance of the calibration process. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
11.
Rill erosion is a serious concern in the hilly region of China with purple soil, and maize is extensively cultivated in this region. Evaluations of the dynamic mechanisms of rill erosion in sloping farmland areas are particularly important during the maize growing season to determine whether rill erosion can occur. A new ridge tillage (RT) system was designed using local agricultural methods in China. Twelve artificial rainfall experiments were conducted in three 1 × 2 m experimental plots with a slope of 15°, which is a typical slope in the study area. The rainfall intensities were designated as 1.0, 1.5, and 2.0 mm min?1. The rainfall experiments were performed in the field to determine the characteristics of run‐off and sediment transport related to rill erosion processes during different stages of maize growth and to analyse how hydraulic parameters and the sediment yield of the rill erosion process are related. The results showed that rill flow patterns were mainly classified as subcritical transition flow during all the growth stages of maize. The effects of hydrodynamic parameters on the sediment yield were ordered as follows: Reynolds number > stream power > Froude number > shear stress. The total sediment yield varied by stage as follows: seedling stage > jointing stage > mature stage > tasseling stage. The sediment yield and run‐off rate exhibited a linear relationship that was well described at the hillslope scale. To initiate soil loss in sloping farmland areas with purple soil during the maize growing season, the critical hydrodynamic shear stress and stream power must be at least 46.505 Pa and 1.541 N m?1 s?1, respectively. 相似文献
12.
Rill erosion is an important erosional form on agricultural soils in England, causing large losses of soil, particularly on cultivated slopes. This paper describes a rill system that developed in a small agricultural catchment in north Oxfordshire during the winter of 1992–93. The rill system comprised two components: a system of ‘feeder rills’ along the valley-side slopes, which were the result of flow concentration and erosion along wheelings, and a thalweg rill, which formed along a dry valley bottom as a result of surface runoff concentration from the feeder rills. Total volumetric soil loss from the rill system was 32·28 m3, equivalent to 3·01 m3, ha?1 for the rill catchment area, or 3·91 t ha?1. Mean discharge for the thalweg rill and feeder rills, calculated during a storm event, was 31·101s?1 and 1·171s?1, respectively. All flows were fully turbulent and supercritical. We emphasize the need for a spatially distributed approach to the study of runoff and erosion at the catchment scale. 相似文献
13.
Rill erosion is a dominant sediment source on sloping lands. However, the amount of soil loss from rills on steep slopes is vastly more than that on gentle slopes because of differences in rill shape and hydraulic patterns. The aims of this paper are to determine the hydrodynamic characteristics of rills and the friction coefficients in steep slope conditions and to propose modifications of some hydraulic parameters used in soil loss prediction models. A series of inflow experiments was conducted on loess slopes. The results show that the geometric and hydraulic properties of rill on the steep loess slopes, which are characterized by the mean width of cross sections, mean velocity and mean depth of flow, are related to discharge and slope gradient in power functions. However, the related exponents to discharge are 0.26, 0.48 and 0.26, respectively, which are different from the exponents derived in previous studies, which were conducted on gentle slopes. The Manning roughness coefficient ranged from 0.035 to 0.071, with an average of 0.0536, and the Darcy–Weisbach friction coefficients varied from 0.4 to 1.9. The roughness coefficients are closely related to the Reynolds numbers and flow volumes; however, the correlations vary with slope gradient. The roughness coefficients are directly proportional to the Reynolds number and the flow volume on steep slopes, in contrast with the roughness coefficients found on gentle slopes, which decrease as the Reynolds number and flow volume increase. This difference is caused by the interactions among the hydraulics of the flow, the shape of the rills and the sediment concentrations on steep slopes. The results indicate that parameters used in models to predict rill erosion have to be modified according to slope gradient. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
14.
Rill development and soil erosion: a laboratory study of slope and rainfall intensity 总被引：7，自引：0，他引：7
Catherine Berger Marcel Schulze Dirk Rieke‐Zapp Fritz Schlunegger 《地球表面变化过程与地形》2010,35(12):1456-1467
A total of 15 rainfall simulation experiments were conducted in a 1 m by 2 m box varying slope (10, 20, 30%) and rainfall intensity (60, 90, 120 mm h?1). The experiments were performed to study how rill networks initiate and evolve over time under controlled conditions with regard to the treatment variables considered, and to allow for input in a computer simulation model. Runoff and sediment yield samples were collected. Digital elevation models were calculated by means of photogrammetry for several time steps of most experiments. The soil used in the experiments was a basal till derived Cambisol typical for the Swiss Plateau. While significant differences were found for sediment yield, runoff did not vary significantly with treatment combinations. Increasing rainfall intensity had a larger effect on sediment yield than increasing slope. Rill density and energy expenditure decreased with time, suggesting that energy expenditure was a useful parameter to describe the emergence of rill network at the laboratory scale. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
15.
Costanza Di Stefano Alessio Nicosia Vincenzo Palmeri Vincenzo Pampalone Vito Ferro 《水文研究》2019,33(26):3330-3348
Rills caused by run‐off concentration on erodible hillslopes have very irregular profiles and cross‐section shapes. Rill erosion directly depends on the hydraulics of flow in the rills, which may differ greatly from hydraulics of flow in larger and regular channels. In this paper, a recently theoretically deduced rill flow resistance equation, based on a power–velocity profile, was tested experimentally on plots of varying slopes (ranging from 9% to 26%) in which mobile and fixed bed rills were incised. Initially, measurements of flow velocity, water depth, cross‐section area, wetted perimeter, and bed slope, carried out in 320 reaches of mobile bed rills and in 165 reaches of fixed rills, were used for calibrating the theoretical flow resistance equation. Then the relationship between the velocity profile parameter Γ, the channel slope, and the flow Froude number was separately calibrated for the mobile bed rills and for the fixed ones. The measurements carried out in both conditions (fixed and mobile bed rills) confirmed that the Darcy–Weisbach friction factor can be accurately estimated using the proposed theoretical approach. For mobile bed rills, the data were supportive of the slope independence hypothesis of velocity, due to the feedback mechanism, stated by Govers. The feedback mechanism was able to produce quasicritical flow conditions. For fixed bed rills, obtained by fixing the rill channel, by a glue, at the end of the experimental run with a mobile bed rill, the slope independence of the flow velocity measurements was also detected. Therefore, an experimental run carried out by a rill bed fixed after modelling flow action is useful to detect the feedback mechanism. Finally, the analysis showed that, for the investigated conditions, the effect of sediment transport on the flow resistance law can be considered negligible respect to the grain roughness effect. 相似文献
16.
Present‐day understanding of rill dynamics is hampered by a lack of detailed data on velocity distributions in rills. The latter are dif?cult to collect with traditional techniques due to the very low water depths and the relatively high ?ow velocities in rills. The objectives of this paper were to investigate the feasibility of miniaturized acoustic Doppler velocimeter (mADV) measurements in rill ?ow and to explore longitudinal variations in ?ow velocities and their relationship with rill bed morphology. Detailed data on longitudinal ?ow velocity were required to achieve these objectives. A 1·8 m long rill was formed freely in a ?ume at 5° slope and 0·001 m3 s?1 discharge. Rill topography was characterized by an alternation of steps and pools. The ?ume surface was then ?xed to preserve rill roughness. A topographical scanning of the entire ?ume surface was made. Velocity was measured with a mADV along the rill, and at different depths. Flow depth in a longitudinal direction was also measured using an elevation gauge. A strong relationship exists between rill topography and ?ow hydraulics. Over steps, ?ow was unidirectional and rapidly accelerating until a threshold Froude number (Fn) value between 1·3 and 1·7 was reached and a hydraulic jump occurred leading to the formation of a pool. In the pool, the ?ow pattern was multidirectional and complex. The ?ow was subcritical when leaving the pool and accelerated over the next step until the threshold Froude number value was again reached. Energy loss in the rill was concentrated in the pools, mainly due to the action of a hydraulic jump. This mechanism of energy dissipation appeared to be an essential factor in rill formation and bedform evolution. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
17.
This study explores factors that affect road surface erosion in a small watershed on the Loess Plateau. Global positioning system (GPS)‐assisted field surveys and geographical information system methods were applied. The results show that road surface rills in the watershed are more easily formed on main roads, which are disturbed by intensive human activities. Secondary unpaved road networks occupied the largest road surface area and contributed 49% of the total road surface rill volumes. Spatial analysis reveals that roads near residential areas or leading to other human‐disturbed land‐use types are at high risk of soil loss. In each road segment, slope gradient, road segment length and drainage area have impacts on surface rill formation and development. Among these factors, slope gradients have been verified as a controlling factor of rill erosion intensification. Both road segment length (R = 0.83, N = 82) and drainage area (R = 0.72 for road segment and 0.76 for upslope drainage areas, N = 82) significantly influence total road surface rill volumes. The interaction variable of road segment length multiplied by slope is more closely correlated with road segment soil loss than that of the independent variables alone. Linear equations composed of slope gradient, road segment length and upslope drainage area are proposed. The new equation performs much better at predicting surface soil loss from secondary road segments compared with the previous models, which have not considered upslope drainage areas. The relationships and equations from this study will be helpful for road erosion evaluation in a small watershed of the study area. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
18.
Different hydraulic gradients, especially due to seepage or drainage, at different locations on a hillslope profile may have a profound effect on the dominant erosion processes. A laboratory study was designed to simulate hillslope processes and quantify effects of surface hydraulic gradients on erosion for a Glynwood clay loam soil (fine, illitic, mesic Aquic Hapludalf). A 5 m long, 1·2 m wide soil pan was used at 5 and 10 per cent slopes with an external watering tube to vary the soil bed's hydrological conditions. Different combinations of slope steepness with seepage or drainage gradients were used to simulate the hydrologic conditions on a 5 m segment of a hillslope profile. Runoff samples were taken during rainfall-only and rainfall with added inflow. Results showed that, under drainage conditions, interrill processes dominated and rilling was limited. The surface contained scattered crescent-shaped pits after the run. Under seepage conditions, rilling processes dominated and the inflow introduced at the top of the soil pan further accelerated the headward erosion of the rills. Erosion rates increased by as much as 60 times under seepage conditions representative of the lower backslope when compared to drainage conditions that generally occur at the upper backslope. This indicated that rills and gullies on backslopes and footslopes may be catalysed or enhanced by seepage conditions rather than form from flow hydraulic shear stress alone. An understanding of spatial and temporal changes that affect both hillslope hydrology and erosional processes is needed to develop accurate process-based erosion prediction models. This knowledge may lead to different management practices on landscape positions where seepage occurs. © 1998 John Wiley & Sons, Ltd. 相似文献
19.
Rill bank collapse is an important component in the adjustment of channel morphology to changes in discharge and sediment flux. Sediment inputs from bank collapse cause abrupt changes in flow resistance, flow patterns and downstream sediment concentrations. Generally, bank retreat involves gradual lateral erosion, caused by flow shear stress, and sudden bank collapse, triggered by complex interactions between channel flow and bank and soil water conditions. Collapse occurs when bank height exceeds the critical height where gravitational forces overcome soil shear strength. An experimental study examined conditions for collapse in eroding rill channels. Experiments with and without a deep water table were carried out on a meandering rill channel in a loamy sand and sandy loam in a laboratory flume under simulated rainfall and controlled runon. Different discharges were used to initiate knickpoint and rill incision. Soil water dynamics were monitored using microstandpipes, tensiometers and time domain reflectometer probes (TDR probes). Bank collapse occurred with newly developed or rising pre‐existing water tables near rill banks, associated with knickpoint migration. Knickpoint scour increased effective bank height, caused positive pore water pressure in the bank toe and reduced negative pore pressures in the unsaturated zone to near zero. Matric tension in unsaturated parts of the bank and a surface seal on the ‘interrill’ zone behind the bank enhanced stability, while increased effective bank height and positive pore water pressure at the bank toe caused instability. With soil water contents >35 per cent (sandy loam) and >23 per cent (loamy sand), critical bank heights were 0·11–0·12 m and 0·06–0·07 m, respectively. Bank toe undercutting at the outside of the rill bends also triggered instability. Bank displacement was quite different on the two soils. On the loamy sand, the failed block slid to the channel bed, revealing only the upper half of the failure plane, while on the sandy loam the failed block toppled forwards, exposing the failure plane for the complete bank height. This study has shown that it is possible to predict location, frequency and magnitude of the rill bank collapse, providing a basis for incorporation into predictive models for hillslope soil loss or rill network development. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
20.
A mathematical model was developed for simulating runoff generation and soil erosion on hillslopes. The model is comprised of three modules: one for overland flow, one for soil infiltration, and one for soil erosion including rill erosion and interrill erosion. Rainfall and slope characteristics affecting soil erosion on hillslopes were analysed. The model results show that the slope length and gradient, time distribution rainfall, and distribution of rills have varying influence on soil erosion. Erosion rate increases nonlinearly with increase in the slope length; a long slope length leads to more serious erosion. The effect of the slope gradient on soil erosion can be both positive and negative. Thus, there exists a critical slope gradient for soil erosion, which is about 45° for the rate of erosion at the end of the slope and about 25° for the accumulated erosion. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献