共查询到20条相似文献，搜索用时 627 毫秒
1.
This paper presents an extensive parametric study on the inelastic response of eight reinforced concrete (RC) planar frames which are subjected to forty five sequential ground motions. Two families of regular and vertically irregular (with setbacks) frames are examined. The first family has been designed for seismic and vertical loads according to European codes while the second one only for vertical loads, to study structures which have been constructed before the introduction of adequate seismic design code provisions. The whole range of frames is subjected to five real seismic sequences which are recorded by the same station, in the same direction and in a short period of time, up to three days. In such cases, there is a significant damage accumulation as a result of multiplicity of earthquakes, and due to lack of time, any rehabilitation action is impractical. Furthermore, the examined frames are also subjected to forty artificial seismic sequences. Comprehensive analysis of the created response databank is employed in order to derive important conclusions. It is found that the sequences of ground motions have a significant effect on the response and, hence, on the design of reinforced concrete frames. Furthermore, it is concluded that the ductility demands of the sequential ground motions can be accurately estimated using appropriate combinations of the corresponding demands of single ground motions. 相似文献
2.
Esra Mete Güneyisi 《地震工程与结构动力学》2012,41(5):853-874
The present paper investigates the seismic reliability of the application of buckling restrained braces (BRBs) for seismic retrofitting of steel moment resisting framed buildings through fragility analysis. Samples of regular three‐storey and eight‐storey steel moment resisting frames were designed with lateral stiffness insufficient to comply with the code drift limitations imposed for steel moment resisting frame systems in earthquake‐prone regions. The frames were then retrofitted with concentrically chevron conventional braces and BRBs. To obtain robust estimators of the seismic reliability, a database including a wide range of natural earthquake ground motion records with markedly different characteristics was used in the fragility analysis. Nonlinear time history analyses were utilized to analyze the structures subjected to these earthquake records. The improvement of seismic reliability achieved through the use of conventional braces and BRBs was evaluated by comparing the fragility curves of the three‐storey and eight‐storey model frames before and after retrofits, considering the probabilities of four distinct damage states. Moreover, the feasibility of mitigating the seismic response of moment resisting steel structures by using conventional braces and BRBs was determined through seismic risk analysis. The results obtained indicate that both conventional braces and especially BRBs improve significantly the seismic behavior of the original building by increasing the median values of the structural fragility curves and reducing the probabilities of exceedance of each damage state. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
3.
In many parts of the world, the repetition of medium–strong intensity earthquake ground motions at brief intervals of time has been observed. The new design philosophies for buildings in seismic areas are based on multi‐level design approaches, which take into account more than a single damageability limit state. According to these approaches, a sequence of seismic actions may produce important consequences on the structural safety. In this paper, the effects of repeated earthquake ground motions on the response of single‐degree‐of‐freedom systems (SDOF) with non‐linear behaviour are analysed. A comparison is performed with the effect of a single seismic event on the originally non‐damaged system for different hysteretic models in terms of pseudo‐acceleration response spectra, behaviour factor q and damage parameters. The elastic–perfect plastic system is the most vulnerable one under repeated earthquake ground motions and is characterized by a strong reduction of the q‐factor. A moment resisting steel frame is analysed as well, showing a reduction of the q‐factor under repeated earthquake ground motions even larger than that of an equivalent SDOF system. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
4.
This study focuses on the response of seismic isolated bridges subjected to near-field ground motions with distinct pulse type behavior in terms of maximum isolator displacements (MIDs) and maximum isolator forces (MIFs) transferred to the substructure. The employed isolation systems are composed of lead rubber bearings (LRBs) with bi-linear force-deformation relations that consider cycle-to-cycle deterioration in the yield strength of the LRBs due to heating of the lead core. MIDs and MIFs with due consideration of cycle-to-cycle deterioration are compared with that of non-deteriorating ones. Bounding analyses are also performed for comparison purposes. Nonlinear response history analyses are conducted with two bins of ground motions recorded at different soil conditions to investigate the effect of ground motion characteristics. Results indicate that MIDs are overestimated by lower bound analyses when seismic isolated bridges are subjected to near-field motions with high velocity pulses especially for the bearings with higher Q/W ratios. 相似文献
5.
During a severe earthquake, steel moment resisting frames are expected to experience significant inelastic deformation in their members and joints. This behaviour is dependent upon several design parameters such as member sizes, frame's overstrength, member deformation capacities and the detailing of components. In this study, the influence of such aspects on the inelastic response of frames is investigated. Inelastic static and dynamic analyses were performed on four frames of different designs for a typical six-storey building. The frames were designed and detailed in accordance with current North American code requirements. The computed response of each frame was compared with the behaviour expected by the codes. Recommendations for a design procedure are suggested for improving the structural performance of low-rise steel frames subjected to strong earthquake excitation. 相似文献
6.
As the forward directivity and fling effect characteristics of the near-fault ground motions, seismic response of structures in the near field of a rupturing fault can be significantly different from those observed in the far field. The unique characteristics of the near-fault ground motions can cause considerable damage during an earthquake. This paper presents results of a study aimed at evaluating the near-fault and far-fault ground motion effects on nonlinear dynamic response and seismic damage of concrete gravity dams including dam-reservoir-foundation interaction. For this purpose, 10 as-recorded earthquake records which display ground motions with an apparent velocity pulse are selected to represent the near-fault ground motion characteristics. The earthquake ground motions recorded at the same site from other events that the epicenter far away from the site are employed as the far-fault ground motions. The Koyna gravity dam, which is selected as a numerical application, is subjected to a set of as-recorded near-fault and far-fault strong ground motion records. The Concrete Damaged Plasticity (CDP) model including the strain hardening or softening behavior is employed in nonlinear analysis. Nonlinear dynamic response and seismic damage analyses of the selected concrete dam subjected to both near-fault and far-fault ground motions are performed. Both local and global damage indices are established as the response parameters. The results obtained from the analyses of the dam subjected to each fault effect are compared with each other. It is seen from the analysis results that the near-fault ground motions, which have significant influence on the dynamic response of dam–reservoir–foundation systems, have the potential to cause more severe damage to the dam body than far-fault ground motions. 相似文献
7.
The 2011 off the Pacific coast of Tohoku earthquake and response of high-rise buildings under long-period ground motions 总被引：1，自引：0，他引：1
I. Takewaki S. MurakamiK. Fujita S. YoshitomiM. Tsuji 《Soil Dynamics and Earthquake Engineering》2011
In the afternoon of March 11, 2011, the eastern Japan was severely attacked by the 2011 off the Pacific coast of Tohoku earthquake (the Great East Japan earthquake). Nearly 30,000 people were killed or are still missing by that earthquake and the ensuing monster tsunami as of April 11, 2011. This paper reports some aspects of this devastating earthquake which hit an advanced country in seismic resistant design. It has been reported that long-period ground motions were induced in Tokyo, Nagoya and Osaka. The properties of these long-period ground motions are discussed from the viewpoint of critical excitation and the seismic behavior of two steel buildings of 40 and 60 stories subjected to the long-period ground motion recorded at Shinjuku, Tokyo is determined and discussed. This paper also reports the effectiveness of visco-elastic dampers like high-hardness rubber dampers in the reduction of responses of super high-rise buildings subjected to such long-period ground motions. The response reduction rate is investigated in detail in addition to the maximum response reduction. In December 2010 before this earthquake, simulated long-period ground motions for earthquake resistant design of high-rise buildings were provided in three large cities in Japan (Tokyo, Nagoya and Osaka) and nine areas were classified. Two 40-story steel buildings (slightly flexible and stiff) are subjected to these long-period ground motions in those nine areas for the detailed investigation of response characteristics of super high-rise buildings in various areas. 相似文献
8.
The response and damage assessment of engineering structures under near-field ground motions is currently of great interest. Near-field ground motion with directivity focusing or fling effects produces pulse-like ground motion that has characteristics different from those of ordinary records. This paper develops simple deterministic and probabilistic models for near-field pulse-like ground motions. These models belong to the class of engineering models that aim to replicate some of the gross features observed in near-field records. The ground velocity is expressed as a steady-state function or a stationary random process modulated by an envelope function. Both models account for the non-stationarity and the multiple pulses in the ground velocity. While the deterministic model is similar to some of the models developed earlier, the probabilistic model facilitates handling uncertainties in the ground motion and variability in the structure's properties. For instance, this model combined with structural reliability methods can be used for reliability assessment of structures under near-field random ground motion. The reduction of the structural response by adding supplemental dampers is also investigated. 相似文献
9.
10.
Influence of earthquake ground‐motion duration on damage estimation: application to steel moment resisting frames 
下载免费PDF全文
下载免费PDF全文 This paper presents an analytical study evaluating the influence of ground motion duration on structural damage of 3‐story, 9‐story, and 20‐story SAC steel moment resisting frame buildings designed for downtown Seattle, WA, USA, using pre‐Northridge codes. Two‐dimensional nonlinear finite element models of the buildings are used to estimate the damage induced by the ground motions. A set of 44 ground motions is used to study the combined effect of spectral acceleration and ground motion significant duration on drift and damage measures. In addition, 10 spectrally equivalent short‐duration shallow crustal ground motions and long‐duration subduction zone records are selected to isolate duration effect and assess its effect on the response. For each ground motion pair, incremental dynamic analyses are performed at at least 20 intensity levels and response measures such as peak interstory drift ratio and energy dissipated are tracked. These response measures are combined into two damage metrics that account for the ductility and energy dissipation. Results indicate that the duration of the ground motion influences, above all, the combined damage measures, although some effect on drift‐based response measures is also observed for larger levels of drift. These results indicate that because the current assessment methodologies do not capture the effects of ground motion duration, both performance‐based and code‐based assessment methodologies should be revised to consider damage measures that are sensitive to duration. Copyright © 2016 John Wiley & Sons, Ltd 相似文献
11.
Two‐story, three‐bay reinforced concrete (RC) frames with and without internal steel frame (ISF) retrofits were tested using continuous pseudo dynamic test method. The ISFs were installed to the middle bay of the RC frame. Test results indicated that ISF retrofit was beneficial in resisting deformation demands without significant damage under simulated ground motions. The ISF shifted the failure mode of the system from a brittle to a ductile mode. The test results were compared with the results of the nonlinear time history analysis. The analysis results were capable of tracing the overall behavior of global response parameters; however, estimations of local demand parameters were less accurate. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
12.
近场地震的动力特性明显不同于远场地震,因此有必要对结构在近场地震作用下的动力性能展开研究。以上部钢结构-下部混凝土结构这类竖向刚度不同的加层混合结构为研究对象,对其在近场脉冲型地震、近场无脉冲型地震及远场地震作用下的动力响应进行研究。结果表明:在多遇、设防、罕遇地震作用下,近场脉冲型地震会使结构的层间位移角、层间剪力、加速度等动力响应均放大并出现超限的情况,而且都比罕遇地震作用下结构的响应增大更明显;在进行近场区加层混合框架结构的设计和建设时,近场脉冲效应会使结构存在不满足规范的情况,有必要对竖向刚度不同的加层混合结构在近场区的适用性进行深入研究。 相似文献
13.
The paper investigates the dynamic behaviour of hybrid systems made of partially restrained (PR) steel–concrete composite frames coupled with viscoelastic dissipative bracings. A numerical model that accounts for both the resisting mechanisms of the joint and the viscoelastic contribution of the dissipative bracing is introduced and briefly discussed. The model is first validated against experimental outcomes obtained on a one‐storey two‐bay composite frame with partial strength semi‐rigid joints subjected to free vibrations. A number of time‐history analyses under different earthquake ground motions and peak ground accelerations are then carried out on the same type of frame. The purpose is to investigate the influence of the type of beam‐to‐column connection and property of the viscoelastic bracing on the performance of the hybrid system. The inherent stiffness of the bare PR frame and the plastic hysteresis of the beam‐to‐column joints, which always lead to only limited damage in the joint, are found to provide a significant contribution to the overall structural performance even under destructive earthquakes. This remark leads to the conclusion that the viscoelastic bracing can be effectively used within the hybrid system. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
14.
Seismic pounding between adjacent frames in multiple-frame bridges and girder ends in multi-span simply supported bridges has been commonly observed in several recent earthquakes. The consequences of pounding include damage to piers, abutments, shear keys, bearings and restrainers, and possible collapse of deck spans. This paper investigates pounding in bridges from an analytical perspective. A simplified nonlinear model of a multiple-frame bridge is developed including the effects of inelastic frame action and nonlinear hinge behavior, to study the seismic response to longitudinal ground motion. Pounding is implemented using the contact force-based Kelvin model, as well as the momentum-based stereomechanical approach, Parameter studies are conducted to determine the effects of frame period ratio, column hysteretic behavior, energy dissipation during impact and near source ground motions on the pounding response of the bridge. The results indicate that pounding is most critical for highly out-of-phase frames and is not significant for frame period ratios greater than 0.7. Impact models without energy dissipation overestimate the displacement and acceleration amplifications due to impact, especially for elastic behavior of the frames. Representation of stiffness degradation in bridge columns is essential in capturing the accurate response of pounding frames subjected to far field ground motion. Finally, it is shown that strength degradation and pounding can result in significant damage to the stiffer frames of the bridge when subjected to large acceleration pulses from near field ground motion records. 相似文献
15.
Nonlinear dynamic response of r.c. framed structures subjected to near-fault ground motions 总被引：2，自引：1，他引：1
The nonlinear dynamic response of reinforced concrete (r.c.) framed buildings subjected to near-fault ground motions is studied
to check the effectiveness of current code provisions with reference to study cases. Three-, six- and twelve-storey r.c. plane
frames, representative of symmetric framed buildings, are designed according to the European seismic code (EC8), assuming
medium and high ductility classes and stratigraphic profiles A (rock) and D (soft soil) in a high-risk seismic region. The
nonlinear seismic analysis is performed using a step-by-step procedure; a bilinear model idealizes the behaviour of the r.c.
frame members. Artificially generated motions (matching EC8 response spectra for subsoil classes A and D) and horizontal motions
(recorded on rock- and soft soil-site at near-fault areas) are considered. The results indicate that near-fault ground motions
may require a special consideration in the code, in particular when designing r.c. framed structures placed on a soft soil-site;
particular attention should be paid to the design of the frame members of the lower storeys. 相似文献
16.
Previous studies have suggested that rocking vibration accompanied by uplift motion might reduce the seismic damage to buildings subjected to severe earthquake motions. This paper reports on the use of shaking table tests and numerical analyses to evaluate and compare the seismic response of base‐plate‐yielding rocking systems with columns allowed to uplift with that of fixed‐base systems. The study is performed using half‐scale three‐storey, 1 × 2 bay braced steel frames with a total height of 5.3 m. Base plates that yield due to column tension were installed at the base of each column. Two types of base plates with different thicknesses are investigated. The earthquake ground motion used for the tests and analyses is the record of the 1940 El Centro NS component with the time scale shortened by a factor of 1/√2. The maximum input acceleration is scaled to examine the structural response at various earthquake intensities. The column base shears in the rocking frames with column uplift are reduced by up to 52% as compared to the fixed‐base frames. Conversely, the maximum roof displacements of the fixed and rocking frames are about the same. It is also noted that the effect of the vertical impact on the column associated with touchdown of the base plate is small because the difference in tensile and compressive forces is primarily due to the self‐limiting tensile force in the column caused by yielding of the base plate. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
17.
This study explores seismic performance of steel frame buildings with SMA-based self-centering bracing systems using a probabilistic approach. The self-centering bracing system described in this study relies on superelastic response of large-diameter cables. The bracing systems is designed such that the SMA cables are always stressed in tension. A four-story steel frame building characterized until collapse in previous research is selected as a case-study building. The selected steel frame building is designed with SMA bracing systems considering various design parameters for SMA braces. Numerical models of these buildings are developed by taking into account the ultimate state of structural components and SMA braces as well as the effect of gravity frames on lateral load resistance. Nonlinear static analyses are conducted to assess the seismic characteristics of each frame and to examine the effect of SMA brace failure on the seismic load carrying capacity of SMA-braced frames. Incremental dynamic analyses (IDA) are performed to compute seismic response of the designed frames at various seismic intensity levels. The results of IDA are used to develop probabilistic seismic demand models for peak inter-story and residual inter-story drifts. Seismic demand hazard curves of peak and residual inter-story drifts are generated by convolving the ground motion hazard with the probabilistic seismic demand models. Results show that steel frames designed with SMA bracing systems provide considerably lower probability of reaching at a damage state level associated with residual drifts compared to a similarly designed steel moment resisting frame, especially for seismic events with high return periods. This indicates reduced risks for the demolition and collapse due to excessive residual drifts for SMA braced steel frames. 相似文献
18.
近断层地震动中长周期、短持时和高能量的加速度脉冲将对高层摩擦摆基础隔震结构的减震性能产生不利影响,考虑土-结构相互作用（SSI效应）后的隔震结构将产生动力耦合效应,可能进一步放大隔震结构地震响应。为此,通过一幢框架-核心筒高层摩擦摆基础隔震结构的非线性地震响应分析,考察近断层脉冲型地震动作用下框架-核心筒摩擦摆基础隔震结构的层间位移角、楼层加速度和隔震层变形等响应规律,揭示隔震体系的损伤机理。基于集总参数SR （sway-rocking）模型,分析不同场地类别与不同地震动类型对隔震体系动力响应影响规律。结果表明:高层摩擦摆基础隔震结构在近断层脉冲型地震动作用下的减震效果相比普通地震动减震效果变差,楼层剪力、层间位移角和隔震层变形等超越普通地震动作用下的1.5倍;对于Ⅲ和Ⅳ类场地类别,考虑SSI效应使隔震结构的地震响应进一步放大,弹塑性层间位移角随着土质变软增大尤为明显。 相似文献
19.
A cloud method for generating percentile engineering demand parameter versus intensity measure(EDP-IM) curves of a structure subjected to a set of synthetic ground motions is presented. To this end, an ensemble of synthetic ground motions based on available real ones is generated. This is done by using attenuation relationships, duration and suitable Gutenberg-Richter relations attributed to the considered seismic hazard at a given site by estimating a suitable distribution of magnitude and site to source distance. The study aims to clarify the significance of the duration and frequency content on the seismic performance of structures, which were not considered in developing percentile incremental dynamic analysis(IDA) curves. The collapse probabilities of two steel moment-resisting frames with different ductility levels generated by IDA and the proposed cloud method are compared at different intensity levels. When compared with conventional IDA, the suggested cloud analysis(SCA) methodology with the same run number of dynamic analyses was able to develop response hazard curves that were more consistent with site-specific seismic hazards. Eliminating the need to find many real records by generating synthetic records consistent with site-specific seismic hazards from a few available recorded ground motions is another advantage of using this scheme over the IDA method.. 相似文献
20.
Large‐scale real‐time hybrid simulation of a three‐story steel frame building with magneto‐rheological dampers 下载免费PDF全文
下载免费PDF全文 A series of large‐scale real‐time hybrid simulations (RTHSs) are conducted on a 0.6‐scale 3‐story steel frame building with magneto‐rheological (MR) dampers. The lateral force resisting system of the prototype building for the study consists of moment resisting frames and damped brace frames (DBFs). The experimental substructure for the RTHS is the DBF with the MR dampers, whereas the remaining structural components of the building including the moment resisting frame and gravity frames are modeled via a nonlinear analytical substructure. Performing RTHS with an experimental substructure that consists of the complete DBF enables the effects of member and connection component deformations on system and damper performance to be accurately accounted for. Data from these tests enable numerical simulation models to be calibrated, provide an understanding and validation of the in‐situ performance of MR dampers, and a means of experimentally validating performance‐based seismic design procedures for real structures. The details of the RTHS procedure are given, including the test setup, the integration algorithm, and actuator control. The results from a series of RTHS are presented that includes actuator control, damper behavior, and the structural response for different MR control laws. The use of the MR dampers is experimentally demonstrated to reduce the response of the structure to strong ground motions. Comparisons of the RTHS results are made with numerical simulations. Based on the results of the study, it is concluded that RTHS can be conducted on realistic structural systems with dampers to enable advancements in resilient earthquake resistant design to be achieved. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献