共查询到19条相似文献,搜索用时 62 毫秒
1.
全球高程基准统一是继全球大地测量坐标系及其参考基准统一之后,大地测量学科面临和亟待解决的一个重要问题,也是全球空间信息共享与交换的基础。本文针对区域高程基准与全球高程基准间基准差异确定的理论、方法及实际问题开展研究。利用物理大地测量高程系统的经典理论方法,给出了高程基准差异的定义,并推导了计算基准差异的严密公式,该公式可将高程基准差异确定的现有3种方法统一起来。在此基础上,分析顾及了不同椭球参数对于计算基准差异的影响及量级,同时,高程异常差法还需考虑全球高程基准重力位与模型计算大地水准面位值不一致引起的零阶项改正。利用青岛原点附近152个GPS水准点数据,分别选择GRS80、WGS-84、CGCS2000参考椭球以及EGM2008、EIGEN-6C4、SGG-UGM-1模型,采用位差法和高程异常差法,确定了我国1985高程基准与全球高程基准的差异。其中,EIGEN-6C4模型计算的我国高程基准与WGS-84参考椭球正常重力位U0定义的全球高程基准之间的差异约为-23.1cm。也就是说,我国高程基准低于采用WGS-84参考椭球正常重力位U0定义的全球高程基准,当选取基于平均海面确定的Gauss-Listing大地水准面作为全球高程基准时,我国1985高程基准高于全球基准约21.0cm。从计算结果还可看出,当前重力场模型在青岛周边不同GPS/水准点的精度差别依然较大,这会导致选择不同数据对确定我国85国家高程基准与全球基准之间的差异影响较大,因此,若要实现厘米级精度区域高程基准与全球高程基准的统一,全球重力场模型的精度和可靠性还需要进一步提高。 相似文献
2.
3.
高程基准是高程测定的依据,由于一些客观原因的存在,目前定义的高程基准只具有局部性特征,而不是全球统一的高程基准。本文针对目前高程基准不统一的现状,分析了现有高程基准统一的几种方法,对其原理进行系统阐述,同时进行了详细评价,指出几种方法的优劣以及适用范围,以期为实际应用提供参考。 相似文献
4.
5.
王文晖 《测绘与空间地理信息》2010,33(4):173-175,177
文章结合泉州市连续运行参考站的建立实例,通过加入精化水准面模型和未加精化水准面模型两种实验数据比对,分析在建设CORS过程中,用精化水准面模型为基准才能得到更加精确的高程数据,中小城市在没有精化水准面模型前提下用坐标联测并进行高程数值拟合的方法求解出近似似大地水准面而得出的高程在测图方面也是可行的。 相似文献
6.
本文详细阐述了我国旧高程基准、黄海高程基准及1985国家高程基准的情况,并以充分的资料讨论了它们之间的关系。 相似文献
7.
8.
确定局部高程基准相对大地水准面的垂直偏差是统一全球高程基准的重要途径。本文的目的是通过大港验潮站坐标直接确定我国高程基准的垂直偏差。首先给出通过大港验潮站坐标确定我国高程基准垂直偏差的基本原理,然后介绍测定大港验潮站平均海面坐标的方法及过程,接下来通过EGM2008和EIGEN-6C4重力场模型计算出的我国高程基准面的重力位,进而推算获得垂直偏差,并与我国东部地区GPS/水准数据的计算结果进行了比较。经分析发现,EGM2008模型计算结果的可靠性要好于EIGEN-6C4模型;利用大港验潮站坐标计算得到的我国高程基准相对大地水准面的垂直偏差为0.344 m,比利用我国东部261个GPS/水准点数据计算获得的偏差值小0.006 m。 相似文献
9.
建立统一的全球高程基准是国际大地测量科学界的核心目标之一,也是全球尺度地球科学研究、跨境工程应用等的必要基础设施。国际大地测量协会(international geodesy association,IAG)2015年发布了国际高程参考系统的定义,并于2019年提出了建立国际高程参考框架的目标。从全球高程参考系统的理论基础和定义出发,对国际高程参考系统与框架的理论、方法和实际问题开展论述与研究,主要包括全球大地水准面重力位 的确定、基于高阶重力场模型的重力位确定、基于区域重力场建模的重力位确定,并重点论述和分析了IAG组织的科罗拉多大地水准面建模试验和中国2020珠峰高程测量实现国际高程参考系统2项典型案例研究。结果表明,在平坦地区和一般山区,重力大地水准面模型精度能达到1 cm(重力位0.1 m2/s2),即使在珠穆朗玛峰这样的特大山区,也有望达到2~3 cm精度(重力位0.2~0.3 m2/s2)。综合典型案例研究结果、观测技术、数据资源和区域分布等因素,提出了建立国际高程参考框架的初步策略,包括IHRF参考站布设、重力位确定方法、数据要求、应遵循的标准/约定和预期精度指标等,展望了光学原子钟与相对论大地测量对于全球高程基准统一的潜在贡献。 相似文献
10.
11.
The crossover adjustment plays a central role in the processing of satellite altimeter measurements. The usual procedure
is to form sea surface height differences at crossover points, solve for the radial orbit error (with due attention to the
singular nature of the estimation problem) and then to construct altimetric sea-level maps using the mean sea surface heights
at the crossover points. Our approach is very different, to make direct use of measurements at crossover points without differencing
and to estimate simultaneously orbit parameters, mean sea surface height and sea surface height variability in a single, unified
adjustment. The technique is suited for repeat data over an area small enough that adjoining passes may be considered to be
parallel and to permit the solution of a set of linear equations of dimension equal to the number of crossover points. The
size of the numerical problem is almost independent of the number of repeat cycles of the altimeter mission. Explicit recognition
is given to the rank defect of the least-squares estimation problem; we show that, for an orbit model with r parameters, the rank defect of the local crossover problem is exactly r
2. The defect may be overcome by choosing an appropriate set of constraints – either giving a best fit of mean sea surface
heights to a reference surface, or minimising orbit parameters, or a minimum norm solution in which both mean sea surface
heights and orbit parameters are minimised. There is no need to choose a reference pass, all passes are treated equally and
data gaps are easily accommodated. Numerical results are presented for the south-western Indian Ocean, based on the first
2 years of altimeter data from the Geosat Exact Repeat Mission.
Received: 31 May 1996 / Accepted: 19 April 1997 相似文献
12.
分析了GPS测量中高程系统转换的实质,介绍了四种GPS高程转换方法的基本原理,然后结合实际算例对四种方法拟合的结果进行了精度分析,总结了各种方法的优缺点,得出一些参考性的结论. 相似文献
13.
14.
邵阳市区域尺度GPS高程异常分析 总被引:1,自引:1,他引:0
针对工程测量中GPS大地高代替水准正常高的问题,该文根据邵阳市实测GPS、水准数据,采用二次曲面拟合模型得到了该地区高程拟合参数。通过正常高与拟合高程进行比较,最大拟合残差为3.9cm,最小为0cm,高程异常模型拟合中误差为1.85cm,证明了该区域GPS高程拟合参数可以满足工程建设中大地高代替正常高的要求。根据GPS高程拟合参数得到的邵阳市辖区及周边地区高程异常曲面具有由西北至东南递减且变化梯度逐渐递减的特征,该区域最大高程异常15.65m,最小高程异常14.75m。 相似文献
15.
16.
二次曲面转换GPS高程,求取转换参数所列方程,方程系数矩阵由已知点的坐标组成,提出利用标准化的方法改良坐标系数矩阵,求取坐标参数.计算结果和精度优于利用坐标中心化、平均值方法. 相似文献
17.
18.
Christopher Kotsakis 《Journal of Geodesy》2008,82(4-5):261-260
Transforming height information that refers to an ellipsoidal Earth reference model, such as the geometric heights determined
from GPS measurements or the geoid undulations obtained by a gravimetric geoid solution, from one geodetic reference frame
(GRF) to another is an important task whose proper implementation is crucial for many geodetic, surveying and mapping applications.
This paper presents the required methodology to deal with the above problem when we are given the Helmert transformation parameters
that link the underlying Cartesian coordinate systems to which an Earth reference ellipsoid is attached. The main emphasis
is on the effect of GRF spatial scale differences in coordinate transformations involving reference ellipsoids, for the particular
case of heights. Since every three-dimensional Cartesian coordinate system ‘gauges’ an attached ellipsoid according to its
own accessible scale, there will exist a supplementary contribution from the scale variation between the involved GRFs on
the relative size of their attached reference ellipsoids. Neglecting such a scale-induced indirect effect corrupts the values
for the curvilinear geodetic coordinates obtained from a similarity transformation model, and meter-level apparent offsets
can be introduced in the transformed heights. The paper explains the above issues in detail and presents the necessary mathematical
framework for their treatment.
An erratum to this article can be found at 相似文献
19.
经典的平差函数模型中只含有无先验统计信息的非随机参数,而针对附有随机参数的平差问题具有很大的局限性,为此在GPS高程拟合中,本文用最小二乘配置模型解决了这一问题,并且通过实际算例,设计两种最小二乘配置拟合方案与二次曲面拟合法进行了比较,结果表明,最小二乘配置拟合残差较小,外符合精度较高,高程拟合效果更好。 相似文献