共查询到17条相似文献，搜索用时 515 毫秒
1.
2.
标准贯人（“标贯”）试验锤击数,要确定粘性土地基承载力标准值简易计算公式。将经杆长修正的标准贯人击数N进行统计分析,再把修正击数平均值带人相关方程,计算粘性土的承载力标准值fk,从而简化了计算过程。 相似文献
3.
针对九江市网纹红土层标准贯入试验实测锤击数与试验孔深、土的压缩模量、抗剪强度关系之间进行了相关性分析。结果表明：网纹红土标准贯入击数与试验孔深为正显著线性相关关系,与土的压缩模量为正弱线性相关关系,与抗剪强度为正弱线性相关关系。分析成果对在九江市开展岩土工程勘察活动具有很好的指导和借鉴意义。 相似文献
4.
目前,国内绝大多数规范规定重探试验应采用φ42 mm钻杆,但从施工方便等因素的考虑,很多工程勘察单位趋向于采用φ50 mm的钻杆进行重探试验。通过分析重探试验要点及其影响因素,基于重探试验锤击数修正系数表,推导出杆径换算系数为0.89,并以海南省某岛礁水运工程实例加以验证。结果表明,同一地貌单元,埋深12 m以浅的珊瑚碎屑层,采用φ42 mm钻杆进行重探试验的击数与采用φ50 mm钻杆进行重探试验的击数之比值为0.875,与推导结果基本一致。 相似文献
5.
王磊 《水文地质工程地质》2012,39(2):85-87
铁路工程地质勘察钻探量巨大,钻探管理存在漏洞,导致许多假标贯击数,影响地质人员对地层的判断,造成不良后果。为提高工程地质勘察质量,以长益常城际铁路勘察为工程背景,用PDCA模式管理方法,对标准贯入试验进行过程控制。依据相关规范,比较标贯击数与土样液性指数所对应的塑性状态,真实度约为79.5%,该方法可供同类工程参考。 相似文献
6.
标准贯入试验是现场测定土体工程性质的重要原位试验,是现场快速判定土体密实度的重要依据,具有及时、可靠、经济等特点,在地质勘察中被广泛的应用。本文通过介绍标准贯入试验的基本原理和设备,比较了英国规范、美国ASTM规范和我国岩土工程勘察规范之间标准贯入试验的差异,介绍了标准贯入试验所适用的经验公式,结合在美国ASTM规范指导下具体的工程实践结果,应用标准贯入试验的结果分析了苏丹国尼罗河Dagash流域内的土体工程性质,对比钻探所得土样和袖珍贯入测力计试验结果,验证了标贯结果的正确性。 相似文献
7.
本文选择华南地区巨厚层花岗岩风化壳分布区的梧州市为研究区,旨在建立系统的、科学的、可操作性强的花岗岩风化壳垂直分带划分标准。在野外区域调查、钻探、原位试验、室内试验、综合研究的基础之上,建立了定性与定量复合判定的指标体系,对梧州市花岗岩风化壳进行了垂直分带以及工程地质特征研究。研究结果表明:(1)粒度分析法可以作为花岗岩风化壳垂直分带划分的方法之一,划分结果与原位试验划分结果具有很好的一致性;(2)残积土带、全风化带、强风化带中含量占比最大的土体分别是黏粒土、粉粒土、砂粒土。随着钻孔深度的增加,粒径相对较大的砾粒和砂粒含量占比逐渐增大,粒径相对较小的粉粒和黏粒含量占比逐渐减小。粒径0.05 mm为残积土带、全风化带、强风化带曲线交叉的分界处,该处土体含量百分比近似相等,揭示粒径0.05 mm值是花岗岩风化壳垂直分带划分的重要指标之一;(3)随着钻进深度的增加,圆锥动力触探试验击数与标准贯入试验击数同时增加,修正后的标准贯入击数N和圆锥动力触探击数N63.5呈多项式相关性。本文建立了花岗岩风化壳垂直分带划分标准,给出了花岗岩风化壳土体地基承载力建议值,对花岗岩分布区的重大工程建设与工程地质特征参数的选取具有一定的指导与参照意义。 相似文献
8.
9.
10.
11.
12.
Determination of undrained strength of fine-grained soils by means of SPT and its application in Turkey 总被引：1，自引：0，他引：1
The Standard Penetration Test (SPT) is one of the oldest and the most common in situ test used in soil explorations. In the recent years with the advent of new technology and techniques in determining the drawbacks in SPT, several researchers have attempted to correlate corrected field measured values with several soil properties. In this context, corrections applied to field values have become critical. In this study a questionnaire including the performance of the standard penetration test and equipment used in practice in Turkey is circulated in order to determine the relevant correction factors. Thus the appropriate corrections are used in acquiring corrected SPT-N values. The relationships between SPT-N and the undrained shear strength (Su) are examined from the statistical point of view by taking the test types and SPT corrections into consideration, and comparison is made with previous studies. It is observed that SPT corrections play an important role on the obtained correlation equations. In addition, the importance of the effects of test types on the correlations is also emphasized. The Standard Penetration Test is found to be sufficient for reliable assessment of Su. 相似文献
13.
14.
Rambhatla G Sastry Sumedha Chahar Manohar N Viladkar 《Journal of Earth System Science》2018,127(5):62
For conjunctive use of geoelectric imaging and geotechnical site investigations in geotechnical characterization of major civil engineering construction sites, an objective assessment of influencing factors is important. Here, we present multiple regression analyses of both geoelectric (Electrical Resistivity Tomography, ERT; Induced Polarization Imaging, IPI) and geotechnical site investigations (Standard Penetration Test, SPT) for two profiles at a construction site for CGEWHO Complex in Greater Noida region, Delhi to assess the role of influencing formation factors like sand, fines and water content. Achieved results show that SPT ‘N’ and IPI are well predicted by a linear multiple regression. On an average, the nonlinear regression has improved predicted SPT ‘N’, resistivity and chargeability by 28.55%, 22.45% and 9.58%, respectively. The influence of sand and fines content is more than that of water content in the prediction of chargeability and SPT ‘N’. RMS error is less in prediction of IPI chargeability (average error of 1.96%) in comparison to SPT ‘N’ value (average error of 11.35%). As factors affecting chargeability (IPI) and SPT ‘N’ are similar, non-invasive IPI can be used along with few geotechnical site investigations for detailed geotechnical site investigations. 相似文献
15.
Geo-engineering tests that include Atterberg limits, linear shrinkage, compaction, California bearing ratio and strength tests
were used to assess the potential of raw-meal to modify Nigerian coal-reject. The results of the tests indicate that the liquid
limit, plastic limit and plasticity index as well as linear shrinkage values decreased with increasing raw meal content. The
results also show that the maximum dry density decreased as raw meal content increased up to a maximum of 6% for the modified
AASHTO and West African Standard (WAS) compaction energies and 2% raw meal content for BS compaction energy. The California
bearing ratio attained optimal value at 2% for the modified AASHTO and West African Standard (WAS) compaction energies and
6% raw meal content for BS compaction energy. Peak shear strength was also achieved at 6% raw meal content. These results
demonstrate that the geotechnical properties of the coal-reject can be improved significantly with the addition of up to 6%
raw meal when compacted at BS compaction energy and 2% raw meal content when compacted at modified AASHTO and WAS compaction
energies. 相似文献
16.
上海地区扁铲侧胀试验与其他原位试验结果的相关性分析 总被引：2，自引：0，他引：2
由于扁铲侧胀试验（DMT）在国内应用时间不长,如何合理地解释和应用DMT试验成果尚待进一步探讨。与其他原位试验结果进行对比分析是研究方法之一。介绍了多元回归在岩土工程相关分析中的应用。根据上海地区多个工程的扁铲侧胀试验、十字板剪切试验、标贯试验和静力触探试验的数据,通过选元分析和多元回归,得出扁铲侧胀试验与其它原位试验的相关关系,可供勘察设计相关人员参考使用。 相似文献
17.
《Geomechanics and Geoengineering》2013,8(2):137-146
This paper describes a numerical model developed to simulate the wave propagation in an elastic media that is applied to in situ dynamic penetration test devices currently used for site characterization. In the model, dynamic equilibrium equations are solved by finite difference analysis in the time domain to produce the discretization of a penetration system – including hammer, rod, penetrometer (or sampler) and soil. In standard penetration tests numerical simulations are shown to agree well with energy measurements derived from force and acceleration signals produced by the impact of a hammer. A parametric study allowed the identification of the relevant factors affecting penetration by demonstrating that the energy effectively delivered to the soil is a function of hammer height of fall and weight of both hammer and rods, as well as the permanent penetration of the penetrometer into the ground produced by a single stroke. Based on these evidences, an approach is suggested to compare results from different dynamic penetration tests without the need to rely on empirical correlations, which is achieved by demonstrating that different equipments should yield the same normalized energy once the influence of both the hammer and rod potential energies are properly considered. 相似文献