首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 78 毫秒
1.
The adsorptive removal of Cr(VI) was studied using activated carbon derived from Leucaena leucocephala (ACLL). The physico-chemical properties of ACLL were determined using proximate analysis and N2 BET surface area analysis. The N2 BET surface area of ACLL was determined to be 1131 m2 g?1. The point of zero charge (pHpzc) of 5.42 indicated that ACLL surface was positively charged for pH below the pHPZC, attracting anions. The effect of experimental operating parameters such as time of contact, ACLL dose, pH, initial concentration and temperature was investigated. The optimum values of parameters such as concentration of 100 mg L?1, 300 mg of ACLL dose, time of contact of 60 min, pH of 4 indicated the maximum Cr(VI) uptake of 13.85 mg g?1. The pseudo-second-order kinetic model best fitted with the Cr(VI) adsorption data. Adsorptive removal of Cr(VI) onto ACLL satisfactorily fitted in the order of Redlich–Peterson > Freundlich > Langmuir > Temkin adsorption isotherm model. The thermodynamic parameters showed the adsorption of Cr(VI) onto ACLL was an endothermic and spontaneously occurred process.  相似文献   

2.
The development of a fast, effective, simple and low-cost procedure for chromium speciation is an analytical challenge. In this work, a new and simple method for speciation and determination of chromium species in different matrices was developed. Sepia pharaonis endoskeleton nano-powder was used as an adsorbent for the dispersive micro-solid-phase extraction. Finally, the desorbed chromium was determined using a graphite furnace atomic absorption spectrometer. The experimental results showed that Cr(III) could be quantitatively extracted by the adsorbent, while Cr(VI) adsorption was negligible. Concentrated H2SO4 and ethanol reduced Cr(VI)–Cr(III), and total chromium content was assessed as Cr(III). Then, the Cr(VI) concentration in the sample was calculated as the difference. The optimum conditions were obtained in terms of pH, adsorbent amount, contact time, and type, concentration and volume of eluent. Under the optimum conditions that involved the speciation of chromium ions from 25 mL of the water samples at pH 7.0 using 0.025 g of the adsorbent with contact time of 5 min, the method was validated in terms of linearity, precision and accuracy. The calibration curve was linear over the concentration range of 0.01–25.00 μg L?1 for Cr(III). The obtained limit of detection for the proposed method was 0.003 µg L?1. The maximum adsorption capacity of the adsorbent was found to be 995.57 mg g?1. The proposed method was validated by the speciation of Cr(III) and Cr(VI) in different real water and wastewater samples with satisfactory results.  相似文献   

3.
Adsorption of Cr(VI) using native and chemically modified marine green macroalgae Codium tomentosum biomass and its adsorption kinetics were studied under specific conditions. Maximum Cr(VI) removal occurred at pH 2 for both untreated and acid-treated biomass. However, base-treated biomass exhibited maximum adsorption at pH 6 due to the hydrolysis of methyl esters present in the cellulose, hemicellulose and lignin molecules resulting in carboxyl groups (COO?) on the surface. The effect of adsorbent dose revealed that untreated and acid-treated biomass follows Henry’s linear isotherm, while base-treated biomass exhibited sigmoidal curve indicating energetic heterogeneity on the adsorbing surface. The monolayer adsorption capacity of untreated, acid-treated and base-treated biomasses was 5.032 ± 0.644, 5.445 ± 0.947, 3.814 ± 0.559 mg g?1, respectively. Adsorption was found to follow Ho and McKay’s pseudo-second-order kinetic model with decreasing pseudo-second-order rate constant (K 2, g mg?1 min?1) of 0.088 ± 0.037 (acid-treated), 0.019 ± 0.003 (untreated) and 0.012 ± 0.003 (base-treated).  相似文献   

4.
Due to its harmful impact on human health, the presence of heavy metals, metalloids and other toxic pollutants in drinking or irrigation water is a major concern. Recent studies have proved that nanosized adsorbents are significantly more effective than their microsized counterparts. Particular attention has been given to nanocomposites with nanoadsorbents embedded in matrixes that could provide stability to the material and contribute to eliminating problems that may appear when using conventional granular systems. This study presents the preparation of a novel hybrid filter from a commercially available polypropylene (PP) non-woven fabric matrix modified with multiwall carbon nanotubes (MWCNT) and iron oxy(hydroxide) nanoparticles, and its use in the removal of As(III). A Box–Behnken statistical experimental design has been chosen to explore relevant variables affecting the filter performance: (1) As(III) concentration, (2) pH and (3) sorbent dose. From an As(III) concentration of 10 mg L?1, at pH 6.5 and with a sorbent dose of 5 g L?1, the PP filter modified with MWCNT removes 10% of the initial metalloid concentration, reaching a capacity of 0.27 mg g?1. After modification with iron oxy(hydroxide), the performance of the material is largely enhanced. The filter, under the same conditions, removes 90% of the initial As(III) concentration, reaching a capacity almost tenfold higher (2.54 mg g?1). This work demonstrates that the developed hybrid filter is effective toward the removal of As(III) in a wide range of pHs. A cubic regression model to compute the removal of the filter as a function of pH and sorbent dose is provided.  相似文献   

5.
This study presents the results of chromate adsorption upon organically modified clinoptilolite obtained by the treatment of Bigadic clinoptilolite with surfactants in primary amine structure, namely 1-dodecylamine, 1-hexadecylamine and oleylamine. Natural and organo-clinoptilolites were characterized by X-ray diffraction, thermal gravimetry and Fourier transform infrared spectrometry which proved the integration of amine groups followed by the order oleylamine > 1-hexadecylamine > 1-dodecylamine. Organo-clinoptilolites were tested for their efficacy in chromate removal under base case conditions which implied 100 ppm initial concentration, pH 4.0, 10 g l?1 adsorbent dose and at 298 K. Results showed that amine loading induced chromate removal reaching up to 90 % for oleylamine-modified clinoptilolite. Experimentation was continued to determine the effects of pH, adsorbent dosage and initial concentration on chromate adsorption. Accordingly, maximum removal of 94.0 % was attained with 14 g l?1 of oleylamine-modified clinoptilolite, from Cr(VI) solution of 100 ppm initially at pH 3.0. Langmuir isotherm described the adsorption of chromate on oleylamine-modified clinoptilolite with 96.4 % consistency. Maximum theoretical uptake capacity was calculated as 6.72 mg g?1. Kinetic data were consistent with pseudo-second-order model with the controlling steps being film and pore diffusions.  相似文献   

6.
Biological treatment of industrial wastewater containing heavy metal and organic pollutant has attracted extensive attention. In this study, Cr(VI) reduction coupled with phenol degradation was investigated by the sulfate-reducing bacteria (SRB) sludge with addition of zero-valent iron (ZVI). The results showed that the SRB wet sludge (SWS) had a good bioactivity in the reduction of Cr(VI) only when the initial concentration of Cr(VI) was below 60 mg L?1. The addition of ZVI significantly enhanced the bioactivity and reusability of SWS, and the reduction percentage of Cr(VI) achieved 98% after SWS was successively used for seven cycles. SWS coupled with ZVI showed a high activity in phenol degradation, with more than 94% phenol being degraded in each cycle. However, in the simultaneous removal of Cr(VI) and phenol, phenol degradation was inhibited due to the toxicity of Cr(VI) to phenol degrading microbes in SWS. On the other hand, reduction of sulfate and Cr(VI) was not affected by the presence of phenol, with more than 95% of sulfate and Cr(VI) being removed at the end of the 5th cycle. This study enriches our understanding on the applications of the SRB sludge in the removal of organic and inorganic contaminants in wastewater.  相似文献   

7.
Batch sorption system using co-immobilized (activated carbon and Bacillus subtilis) beads as adsorbent was investigated to remove Cr(VI) from aqueous solution. Fourier transform infrared spectroscopy analysis showed the functional groups of both bacteria and activated carbon in co-immobilized beads. Experiments were carried out as a function of contact time (5–300 min), initial metal concentration (50–200 mg L?1), pH (2–8), and adsorbent dose (0.2–1 g L?1). The maximum percentage of removal was found to be 99 %. Langmuir model showed satisfactory fit to the equilibrium adsorption data of co-immobilized beads. The kinetics of the adsorption followed pseudo-second-order rate expression, which demonstrates that chemisorption plays a significant role in the adsorption mechanism. The significant shift in the Fourier transform infrared spectroscopy peaks and a Cr peak in the scanning electron microscope–energy dispersive spectroscopy spectra further confirmed the adsorption. The results indicate that co-immobilized beads can be used as an effective adsorbent for the removal of Cr(VI) from the aqueous solution.  相似文献   

8.
The removal of hexavalent chromium from wastewater streams has received an considerable attention in recent years, since it can cause harmful effects on the environment. Several approaches, including adsorption, are recognized to tackle this problem, but unfortunately most of these processes are impressed with practical conditions of the experiments. The main objective of this study was to recognize applicable conditions for Cr(VI) removal from an industrial drainage using nature-derived adsorbents (brown coal and modified zeolite) and to make the process more adaptive by using adsorbents conjointly. Batch experiments were carried out by agitating Cr(VI) stock solution with adsorbents at room temperature. The influence of main operating parameters was explored, and the best proportion of the adsorbents was determined. Maximum sorption of Cr(VI) onto brown coal was observed at pH = 4 by adding 60 g L?1 adsorbent to contaminated solution. In case of using zeolite, the modification process was required, and the pH indicated a weak influence in a wide range (2–8). Optimum dosage of modified zeolite for Cr(VI) removal was 10 g L?1. The hybrid application of adsorbents with the mass ratio of brown coal/modified zeolite at (3:1) was capable of removing more than 99% of Cr(VI) from contaminated wastewater in the natural pH range of the wastewater. The adsorption of Cr(VI) by brown coal and modified zeolite followed Langmuir and Freundlich isotherm models, respectively. Sorption of Cr(VI) onto both brown coal and modified zeolite fitted well to pseudo-second-order rate reaction.  相似文献   

9.
There are compelling economic and environmental reasons to remove pesticides from wastewater because they are toxic and carcinogenic. The effectiveness of copper-based metal–organic framework (Cu-BTC) for adsorbing the insecticide 14C-ethion from wastewater has been studied as function of contact time, adsorbent dosage, temperature and pH. 14C-ethion/Cu-BTC isotherms exhibit two plateaus (BET type IV) and are reliably represented by Brunauer–Deming–Deming–Teller and Zhu–Gu models, with deviations of only 1.99 and 3.95%, respectively. The removal curve measured under batch operation is well represented by a pseudo-first-order equation, yielding results equivalent to the theoretical linear driving force model of Glueckauf. At pH 7, 75 mg L?1 ethion concentration, 150 min, 25 °C and 0.425 g L?1 Cu-BTC dose, the sorbent capacity is ca. 122 mg g?1. Moreover, Cu-BTC has a good stability after six adsorptions cycles. Finally, our results disclose the fundamental understanding of the adsorption mechanism: the ethion molecule coordinates to two copper(II) atoms across the metal–organic framework channel via the phosphoryl (P–O) group.  相似文献   

10.
Microwave-assisted tetrabutyl ammonium-impregnated sulphate-crosslinked chitosan was synthesized for enhanced adsorption of hexavalent chromium. The adsorbent obtained was extensively characterized using Fourier transform infrared, X-ray diffraction, scanning electron microscopy and energy-dispersive X-ray studies. Various isotherm models such as Langmuir, Freundlich and Dubinin–Radushkevich were studied to comprehend the adsorption mechanism of hexavalent chromium by the adsorbent. Maximum adsorption capacity of 225.9 mg g?1 was observed at pH 3.0 in accordance with Langmuir isotherm model. The sorption kinetics and thermodynamic studies revealed that adsorption of hexavalent chromium followed pseudo-second-order kinetics with exothermic and spontaneous behaviour. A column packed with 1 g of adsorbent was found to give complete adsorption of Cr(VI) up to 900 mL of 200 mg L?1 solution which discerns the applicability of the adsorbent material for higher sample volumes in column studies. The effective adsorption results were obtained due to both ion exchange and ion pair interaction of adsorbent with hexavalent chromium. Greener aspect of overall adsorption was regeneration of the adsorbent which was carried out using sodium hydroxide solution. In the present study, the regenerated adsorbent was effectively reused up to ten adsorption–desorption cycles with no loss in adsorption efficiency.  相似文献   

11.
Phanerochaete chrysosporium, a white rot basidiomycete, was immobilized over Luffa cylindrica sponge discs, treated with 0.1 N HCl and its potentiality for the removal of hexavalent chromium [Cr(VI)] from water was investigated in both batch and in up-flow fixed-bed bioreactor. The acid treatment of biomass increased the uptake capacity and percentage removal of Cr(VI) from 33.5 to 46.5 mg g?1 and 67 to 92 %, respectively. Maximum uptake of Cr(VI) was achieved at pH 2, temperature 40 °C after 100 min of contact time. The Cr(VI) sorption on the biomass was better explained by Langmuir isotherm. Thermodynamic studies indicated that the process was spontaneous and endothermic. Sorption kinetic study showed that pseudo-second-order model best correlates the Cr(VI) sorption on the biomass as compare to pseudo-first-order kinetic model. The performance of fixed-bed bioreactor was evaluated at different bed heights (5, 15 and 25 cm) and flow rates (1.66, 4.98 and 8.33 mL min?1) by using bed depth service time model. Response surface methodology statistical method was applied for optimizing the process parameters. FTIR analysis showed that amino groups were mainly involved in adsorption of Cr(VI).  相似文献   

12.
This study analyses the adsorption of Pb(II) and Cr(III) in soils. These metals are commonly found together in nature in urban wastes or industrial spillages, and the theoretical approach of the work was to evaluate the response of the soil to continuous Cr and Pb spillages to soil in terms of several physicochemical parameters. The influence of an anthropogenic input of phosphorus was evaluated. Continuous flow experiments were run in duplicates in acrylic columns (25 cm × 3.2 cm). The influent Cr(III) and Pb(II) solutions of 10 mg l?1 and 25 mg l?1 at pH 5 were pumped upward through the bottom of the columns to ensure saturation flow conditions. Also, successive experiments were run with the above concentrations of Cr(III) and Pb(II) and NaH2PO4, keeping metal to phosphorus ratio of 1:0, 1:0.1 and 1:1. Modelling parameters included Freundlich and Langmuir equations, together with the Two-site adsorption model using CXTFIT code. Results obtained allowed concluding that Pb(II) adsorption presents a certain degree of irreversibility and the continued spillages over soil increment the fraction which is not easily desorbed. Cr(III) desorption was almost complete, evidencing its high mobility in nature. The presence of an anthropogenic input of phosphorus leads to a marked increase of both Pb(II) and Cr(III) adsorption in soils. Z-potential measurements allow to discard the electrostatic attraction of Cr(III) and Pb(II) with the surface charged soil as the dominant process of metal sorption. Instead, CheaqsPro simulation allows to identify PbH2PO4 +, PbHPO4 (aq) and CrHPO4 + as the dominant species which regulate Cr(III) and Pb(II) transport in soils.  相似文献   

13.
Adsorption characteristics of water hyacinth roots powder for the removal of Indosol Dark-blue GL dye were investigated in batch mode. Operating variables, such as initial solution pH, presence of detergent, adsorbent dosage, initial concentration and contact time, were studied. The results showed that the adsorption of dye increased with increasing the initial concentration and contact time. The adsorption is highly pH dependent and adsorption capacity increased with decrease in pH. Kinetic study revealed that the uptake of Indosol Dark-blue GL was very rapid within the first 15 min and equilibrium time was independent of initial concentration. Batch equilibrium experiments were carried out at different pH and found that equilibrium data fitted well to Langmuir isotherm model. The maximum sorption capacity of the adsorbent was found as 86 mg g?1 at pH 3 which reduced to 64 mg g?1 at pH 5. The presence of detergent reduced the sorption capacity of the adsorbent significantly. Using equilibrium and kinetic data, the forward and backward rate constants were determined from the unified approach model. Desorption study revealed that the dye can be recovered by swing the pH from low to high.  相似文献   

14.
The results of investigations (SEM/EDS and AAS) of a peat deposit, spanning 13,000 years of peat accumulation, are shown. The peat deposit is located in a region of shallow occurrence of Zn–Pb ores, near Tarnowskie Góry town, within the Cracow–Silesia district (southern Poland). Exploitation of lead, silver and iron during the medieval times (Twelfth and thirteenth century) was confirmed by historical documents whereas there are no unambiguous data showing that there was metal mining during the Romanian or earlier times in the region. The peat deposit is located within the influence of atmospheric Pb and Zn emission from a nearby Zn–Pb smelter. Two vertical peat profiles were investigated (120 and 140 cm depth of profile) showing variable concentrations of Zn up to 713 mg kg?1, Pb up to 317 mg kg?1, Cd up to 13 mg kg?1 and Tl up to 31 mg kg?1. The highest concentrations were recorded for the uppermost peat layers. SEM and EDS investigations revealed the occurrence of metalbearing, submicroscopic mineral components: Fe, Mn, Ti and Zn oxides and Zn and Pb carbonates. The top layer of the deposit contained Zn, Pb and Cd sulphides. The occurrence of aggregates of Au–Ag, Cu–Zn and Au–Ag–Cu alloys can be possibly related to pre-historical mining and smelting or be explained by geochemical transformations. The preservation of carbonates and oxides in the peat is discussed, indicating a generally neutral to alkaline peat water chemistry and maintenance of an oxidized environment in the fen.  相似文献   

15.
The role of rhizospheric microbes of giant reed (Arundo donax L.) in Cr uptake from hydroponic culture was investigated. The control group was exposed to Cr in range of 25–100 mg L?1 containing a control itself (with no metal addition). The experimental group received same Cr treatments, but in addition was exposed to antibiotic treatment in order to inhibit rhizospheric bacteria. The range of Cr accumulated in the roots was 3–7.65 mg L?1; in stem it ranged 2.15–42.4 mg kg?1; while in leaves, the range of Cr content was 13.7–15 mg kg?1. Overall, Cr uptake in A. donax (without rhizobacterial inhibition) was root < leaf < stem. However, the amount of Cr uptake in plants with rhizobacterial inhibition was significantly less (~4.6-folds in 100 mg L?1 Cr treatment) than those without such inhibition clearly highlighting that rhizobacterial inhibition decreased the Cr uptake. The experimental results clearly demonstrated that the inhibition of the rhizobacterial populations had great influence on the Cr uptake. However, Cr uptake could not be completely inhibited as some metal uptake was observed after the rhizobacterial inhibition although it was significantly less than the Cr uptake of plants without such inhibition.  相似文献   

16.
The present article explores the ability of five different combinations of two adsorbents (Arachis hypogea shell powder and Eucalyptus cameldulensis saw dust) to remove Pb(II) from synthetic and lead acid batteries wastewater through batch and column mode. The effects of solution pH, adsorbent dose, initial Pb(II) concentration and contact time were investigated with synthetic solutions in batch mode. The Fourier transform infrared spectroscopy study revealed that carboxyl and hydroxyl functional groups were mostly responsible for the removal of Pb(II) ions from test solutions. The kinetic data were found to follow pseudo-second-order model with correlation coefficient of 0.99. Among Freundlich and Langmuir adsorption models, the Langmuir model provided the best fit to the equilibrium data with maximum adsorption capacity of 270.2 mg g?1. Column studies were carried out using lead battery wastewater at different flow rates and bed depths. Two kinetic models, viz. Thomas and Bed depth service time model, were applied to predict the breakthrough curves and breakthrough service time. The Pb(II) uptake capacity (q e = 540.41 mg g?1) was obtained using bed depth of 35 cm and a flow rate of 1.0 mL min?1 at 6.0 pH. The results from this study showed that adsorption capacity of agricultural residues in different combinations is much better than reported by other authors, authenticating that the prepared biosorbents have potential in remediation of Pb-contaminated waters.  相似文献   

17.
In this work, the effectiveness of native and chemically modified rice bran to remove heavy metal Pb(II) ions from aqueous solution was examined. Chemical modifications with some simple and low-cost chemicals resulted in enhancement of the adsorption capacities and had faster kinetics than native rice bran. Experiments were conducted in shake flasks to monitor the upshot of parameters over a range of pH, initial Pb(II) concentrations and contact times using a batch model study. The sorption capacities q (mg g?1) increased in the following order: NaOH (147.78), Ca(OH)2 (139.08), Al(OH)3 (127.24), esterification (124.28), NaHCO3 (118.08), methylation (118.88), Na2CO3 (117.12) and native (80.24). The utmost uptake capacity q (mg g?1) was shown by NaOH-pretreated rice bran. The results showed that, using NaOH-modified rice bran, the chief removal of Pb(II) was 74.54 % at pH 5, primary Pb(II) concentration 100 mg L?1 and contact time 240 min. Equilibrium isotherms for the Pb(II) adsorption were analyzed by Langmuir and Freundlich isotherm models. The Langmuir isotherm model, showing Pb(II) sorption as accessible through the high value of the correlation coefficient (R 2 = 0.993), showed a q max value of 416.61 mg g?1. The kinetic model illustrated adsorption rates well, depicted by a second order, which gives an indication concerning the rate-limiting step. Thermodynamic evaluation of the metal ion ?G o was carried out and led to the observation that the adsorption reaction is spontaneous and endothermic in nature. NaOH chemically modified rice bran was a superb biosorbent for exclusion of Pb(II) and proved to be excellent for industrial applications.  相似文献   

18.
Nitrate removal from water has been accomplished by heterotrophic biofilms using organic carbon as a source of reducing power. To overcome the natural limitation in organic carbon in water, a poly-ε-caprolactone based biofilm carrier that serves simultaneously as a biofilm carrier and as a source of organic carbon was developed and tested in the present work. The feasibility of the new biofilm carrier for nitrate removal from water was evaluated in a packed bed reactor. The combination of size and structure provided a carrier element having high surface area and void volume, 1,170 m2/m3 and 67 %, respectively. A maximum denitrification rate of 4.4 mg N–NO3 ?/(L.h) (9.2 mg N–NO3 ?/(m2.h)) was achieved in the packed bed reactor at 20 °C and pH 7.0. Main advantages of the biofilm carrier developed in the present work are its mechanical stability in water even after biofilm formation and controlled release of organic carbon by enzymatic reactions. The proposed biotechnology to remove nitrate from groundwater is robust and easy to operate.  相似文献   

19.
Colloidal pyrite waste rocks (CPWR) which are mainly composed of colloidal pyrite and siderite widely deposit in sulfide mines in the middle and lower reaches of the Yangtze River belt, China, especially in Tongling City, Anhui Province, China. In this paper, a fixed-bed column was used to investigate the weathering and oxidation of CPWR and its role in immobilizing low-concentration Cu (10 mg L?1) under weakly acidic leach (pH = 5.0). The experimental results indicated that the breakthrough capacity was around 14.0 mg Cu g?1 CPWR when Cu2+ breakthrough concentration was 0.5 mg L?1. Sequential extraction of Cu and dithionite–citrate–bicarbonate extraction of free iron in the used CPWR after the column breakthrough indicated that Cu removal by CPWR consisted of the following processes: oxidation of pyrite and dissolution of siderite in CPWR, ferrous oxidation, and adsorption of Cu on ferric (hydr)oxides. This study shows the potential application of CPWR as an effective sorbent for the removal of low-concentration Cu from acid mine drainage.  相似文献   

20.
The goal of this study was to evaluate the soil properties and their modifications within the rhizosphere of spontaneous vegetation as key factors to assess the phytomanagement of a salt marsh polluted by mining wastes. A field survey was performed based on a plot sampling design. The results provided by the analyses of rhizospheric soil (pH, electrical conductivity (EC), organic carbon, total nitrogen, etc.) and metal(loid)s’ phytoavailability (assessed by EDTA) were discussed and related to plant metal uptake. The averages of pH and EC values of the bulk soil and rhizospheric samples were in the range of neutral to slightly alkaline (pH 7–8) to saline (>2 dS m?1), respectively. Heavy metal and As concentrations (e.g. ~600 mg kg?1 As, ~50 mg kg?1 Cd, ~11,000 mg kg?1 Pb) were higher in the rhizosphere for both total and EDTA-extractable fraction. Phragmites australis uptaked the highest concentrations in roots (e.g. ~66 mg kg?1 As, ~1,770 mg kg?1 Zn) but not in shoots, for which most of plant species showed low values for Zn (<300 mg kg?1) but not for Cd (>0.5 mg kg?1) or Pb (~20–40 mg kg?1). Vegetation distribution in the studied salt marsh looked to be more affected by salinity than by metal pollution. The free availability of water for plants and the incoming nutrient-enriched effluents which flow through the salt marsh may have hindered the metal(loid)s’ phytotoxicity. The phytomanagement of these polluted areas employing the spontaneous vegetation is a good option in order to improve the ecological indicators and to prevent the transport of pollutants to nearby areas.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号