首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Ground water monitoring networks can provide vital information for sustainable water resources management. This involves the measurement of ground water level, solute concentration, or both. This article deals with the former. It optimizes network distribution of piezometer or data sampling wells to effectively monitor ground water levels under an irrigation region while retaining adequate overall measurement accuracy. This article presents a structured process for applying principal component analysis (PCA) in optimizing a ground water monitoring network in an irrigation area of Australia. The PCA functions, distributed with the MATLAB package, were used to determine relative contributions of individual piezometers in capturing the spatiotemporal variation of ground water levels. Kriging gridding interpolation algorithm was used to render the data surface presentations and determine spatial differences in piezometeric surfaces using different number of data sets. The results show that the overall difference of ground water level between the original piezometer network and the optimized networks after the PCA process was applied is less than 20%, while the total number of piezometers in the optimized network is reduced by 63%, which will save the time and cost to monitor ground water levels in the irrigation area.  相似文献   

2.
Data from an existing network of ground water monitoring wells at the U.S. Department of Energy (DOE) Hoe Creek Underground Coal Gasification (UCG) Experimental Site indicated that organic contaminants, particularly phenols produced during gasification experiments, were threatening neighboring ground water resources. The existing monitoring well network was sparse and further definition of the extent and direction of contaminant migration was needed. Additionally, water level data, important in determining flow directions, was incomplete. A field program was designed and implemented to locate and define the organic contamination and expand the existing ground water monitoring program. The program utilized field analysis of phenol for contaminant detection and well location, followed by completion using gas-drive ground water samplers/piezometers. Geophysical logging was used to permit optimum placement of the samplers. The geologic aspects of the site posed some interesting problems to the installation of the samplers. The contaminant plume edge was defined in the east, west and south directions during the field program. Further work is needed in the north direction.  相似文献   

3.
A New Multilevel Ground Water Monitoring System Using Multichannel Tubing   总被引：5，自引：0，他引：5  
A new multilevel ground water monitoring system has been developed that uses custom-extruded flexible 1.6-inch (4.1 cm) outside-diameter (O.D.) multichannel HOPE tubing (referred to as Continuous Multichannel Tubing or CMT) to monitor as many as seven discrete zones within a single borehole in either unconsolidated sediments or bedrock. Prior to inserting the tubing in the borehole, ports are created that allow ground water to enter six outer pie-shaped channels (nominal diameter = 0.5 inch [1.3 cm]) and a central hexagonal center channel (nominal diameter = 0.4 inch [1 cm]) at different depths, facilitating the measurement of depth-discrete piezometric heads and the collection of depth-discrete ground water samples. Sand packs and annular seals between the various monitored zones can be installed using conventional tremie methods. Alternatively, bentonite packers and prepacked sand packs have been developed that are attached to the tubing at the ground surface, facilitating precise positioning of annular seals and sand packs. Inflatable rubber packers for permanent or temporary installations in bedrock aquifers are currently undergoing site trials. Hydraulic heads are measured with conventional water-level meters or electronic pressure transducers to generate vertical profiles of hydraulic head. Ground water samples are collected using peristaltic pumps, small-diameter bailers, inertial lift pumps, or small-diameter canister samplers. For monitoring hydrophobic organic compounds, the CMT tubing is susceptible to both positive and negative biases caused by sorption, desorption, and diffusion. These biases can be minimized by: (1) purging the channels prior to sampling, (2) collecting samples from separate 0.25-inch (0.64 cm) O.D. Teflon sampling tubing inserted to the bottom of each sampling channel, or (3) collecting the samples downhole using sampling devices positioned next to the intake ports. More than 1000 CMT multilevel wells have been installed in North America and Europe to depths up to 260 feet (79 m) below ground surface. These wells have been installed in boreholes created in unconsolidated sediments and bedrock using a wide range of drilling equipment, including sonic, air rotary, diamond-bit coring, hollow-stem auger, and direct push. This paper presents a discussion of three field trials of the system, demonstrating its versatility and illustrating the type of depth-discrete data that can be collected with the system.  相似文献   

4.
This paper describes a drive point system for installing small‐diameter (15 to 25 mm ID) piezometers to depths of several metres in unconsolidated sediments. The system fills the gap between (1) heavy duty drive point systems powered by drilling rig hydraulics or air hammers that are capable of installing large diameter drive points to depths of many tens of metres and (2) manually driven systems that typically install 10 mm ID or smaller tubing to depths of <2 m. Unlike many existing systems, which install piezometers inside an outer casing that is later removed, our system protects the piezometer screen inside the casing and extends it only once the casing is driven to the desired depth. This avoids clogging of the screen during installation and the risk of creating an annulus around the piezometer, which can provide a preferential pathway for water movement. The piezometer has a larger diameter than most manually driven systems, and thus has a higher yield; it also permits use of most commercially available pressure transducers and electrical conductivity sensors. The piezometers have been successfully installed to depths of up to 6 m using an electric hammer. The system overcomes some issues associated with existing systems and provides the advantages of affordability, rapid installation, mechanical assistance and manual portability.  相似文献   

5.
A pilot-scale nutrient injection will (NIW) (4 m by 4 m by 1 m) was installed in the Borden Aquifer lo serve as a pulsed injection source of a potassium acetate solution for the stimulation of anaerobic microbial activity. The success of the flushing procedure was evaluated by monitoring the breakthrough of the acetate solution at several multilevel piezometers installed in the wall. Although some variation in the ground water velocity was observed with depth, the wall was flushed with reasonable uniformity after about six hours of injection and withdrawal, representing about one pore volume, Calculations bused on head level data collected during the flush, and on the solute breakthrough curves, indicated that about 90% of the flow induced by the pumping and injecting was confined to the permeable wall. These results show that a permeable wall injection system is a viable method of introducing solutes uniformly to a cross section of aquifer, with minimal perturbation of the natural flow system. In addition lo its importance for the biostimulation system tested in this project the flushing of permeable walls may have applications in other semi-passive remedial systems, such as the rejuvenation of reactive barriers.  相似文献   

6.
An impact drive point method is described for emplacing piezometers in a cobble river bottom where this has previously been difficult without the use of drilling rigs. To force the drive point piezometers through coble, the vibrational impact of an air-powered hammer was carried directly to the drive point by the use of an internal drive rod. After insertion to depth, the drive rod was removed from the lower portion of the piezometer and a standpipe was added to extend the piezometer above the river level. Piezometers installed in this way have permitted water quality analysis and dynamic measurement of vertical potentials in cobble sediments ranging in size from 2.5 to >30 cm and the method has been successfully used in the Columbia River, USA, and Töss River, Switzerland. This innovative method provides information on the hydrodynamics of pore water in highly permeable, cobble deposits that are common in high-energy river and lake bottoms. Piezometers installed using the internal drive rod method facilitate the assessment of the temporal and spatial dynamics of recharge and discharge at the ground water/surface water interface and analyses of the ecological connectivity between the hyporheic zone and surface water of rivers and streams. This information will lead to improved management decisions related to our nation's ground water and surface water supplies.  相似文献   

7.
Hydrogeologic and ground water quality data obtained from a gas-driven multilevel sampler system and a polyvinyl chloride (PVC) monitoring well nest with the same aquifer communication intervals are compared. All monitoring points are in close proximity to each other. The study was conducted at an eight-acre uncontrolled hazardous waste site. The site is located in an alluvial valley composed of approximately 40 feet of alluvium overlying shale bedrock. The ground water at the site is contaminated with various organic constituents. A ground water monitoring network consisting of 26 conventional monitoring wells, nine observation well points, and six multilevel gas-driven samplers was established to characterize the hydrogeologic regime and define the vertical and horizontal extent of contamination in the vicinity of the abandoned chemical plant. As part of this study, a multilevel monitoring system was installed adjacent to a well nest. The communication zones of the multilevel samplers were placed at the same elevation as the sand packs of the well nest. The multilevel sampler system and well nest are located in a contaminated area directly downgradient of the site. A comparison of the vertical head distribution and ground water quality was performed between the well nest and the multilevel sampling system. The gas-driven multilevel sampling system consists of three gas-driven samplers that monitor separate intervals in the unconsolidated materials. The well nest, composed of two PVC monitoring wells in separate boreholes, has the same communication interval as the other two gas-driven samplers. Hydraulic head information for each multilevel sampler was obtained using capillary tubing. This was compared with heads obtained from the well nest utilizing an electric water level indicator. Chemical analyses from the PVC and multilevel sampler wells were performed and compared with one another. The analyses included organic acids, base neutrals, pesticides, PCBs, metals, volatile organics, TOX, TOC, CN, pH and specific conductance.  相似文献   

8.
The screened auger is a laser-slotted, hollow-stem auger through which a representative sample of ground water is pumped from an aquifer and tested for water-quality parameters by appropriate field-screening methods. Screened auger sampling can be applied to ground water quality remedial investigations, providing:(1) a mechanism for determining a monitoring well's optimal screen placement in a contaminant plume; and (2) data to define the three-dimensional configuration of the contaminant plume.
Screened auger sampling has provided an efficient method for investigating hexavalent chromium and volatile organic compound contamination in two sandy aquifers in Cadillac, Michigan. The aquifers approach 200 feet in thickness and more than 1 square mile in area. A series of screened auger borings and monitoring wells was installed, and ground water was collected at 10-foot intervals as the boreholes were advanced to define the horizontal and vertical distribution of the contaminant plumes. The ability of the screened auger to obtain representative ground water samples was supported by the statistical comparison of field screening results and subsequent laboratory analysis of ground water from installed monitoring wells.  相似文献   

9.
A newly developed technique which allows the down-hole sampling and subsequent analysis of ground water for trace organic contaminants was tested during an investigation of contaminant migration at an inactive landfill site in Burlington, Ontario, Canada. The sampling device, which is lowered down piezometers with a tube, consists of a small cylindrical cartridge of sorbent material attached to a syringe. Vacuum or pressure applied at the surface controls the movement of the plunger in the syringe. The volume of the syringe determines the volume of sample water that passes through the cartridge. The cartridge is removed from the syringe at the surface. One cartridge is used for each sampling; the syringe is reusable. The residual water in the cartridge is removed in the laboratory, and the cartridge is desorbed to a fused silica capillary column for analysis by gas chromatography (GC). The analyses discussed here were performed on a GC/mass spectrometer/data system (GC/MS/DS). Of the many organic compounds that were identified in the samples, three compounds were clearly landfill-related: 1,1,1-trichloroethane, chlorobenzene, and para-dichlorobenzene. The three compounds were found at levels substantially above blank levels in 9, 5, and 5 piezometers, respectively. The average concentrations were 14., 5.3, and 0.88μg/1 (ppb), respectively. The pooled coefficients of variation for the analyses for the three compounds were 27., 6.9, and 6.4%, respectively. The volatility of 1,1,1-trichloroethane was probably the cause of the greater variability in its analytical data. The main advantages of the technique over most conventional sampling methods include: (1) down-hole sampling in a manner which minimizes the potential for volatilization losses; (2) avoidance of passage of the sample through long sections of tubing that may contaminate the sample or cause adsorptive losses; (3) convenience of sample handling, storage, and shipping; and (4) high sensitivity.  相似文献   

10.
A zone of contaminated ground water has been identified in an unconfined sand aquifer adjacent to a pit into which spent pulp liquor was intermittently discharged from 1970 to 1979. A network of multilevel sampling, bundle-type piezometers was installed. Up to seven depthspecific sampling points were incorporated into each piezometer providing a cost-effective means for three-dimensional mapping of hydraulic head and water quality in the unconfined sand aquifer. Ground-water samples retrieved from this network showed an area of contamination 900 m long, 400 m wide, and more than 25 m deep. This plume is dispersed about the ground-water flow lines passing beneath the waste disposal pit, and it terminates at a vigorous ground-water discharge area located 800 m from the pit. The contaminated ground water is characterized by elevated concentrations of sodium (3,000 mg/1), chloride (590 mg/1), alkalinity (2,700 mg/1), total organic carbon (2,000 mg/1), chemical oxygen demand (10,800 mg/1), biological oxygen demand (2,000 mg/1), tannin and lignin (780 mg/1), and lower sulphate (1 mg/1) compared to background ground waters in the area. The apparent rate of sodium migration is more than 50 m/yr and is close to the average linear ground-water velocity. Removal of some organic matter by biological transformation has produced the increased alkalinity in the contaminated ground water and somewhat reduced pH. Tannin and lignin are relatively inert compared to other organic compounds found in the waste liquor. Extremely low sulphate levels occurring in the highly contaminated ground waters indicate the existence of conditions favorable for microbially-mediated sulphate reduction.  相似文献   

11.
Abstract

Piezometers and wells installed for water quality monitoring are frequently used to assess the saturated hydraulic conductivity (K) in the surrounding formation. A series of recovery tests was conducted to evaluate how purging, required to obtain representative water quality samples, affected measured values of hydraulic conductivity in 15 newly installed and undeveloped piezometers placed to between 2 and 15 m depth (in oxidized and unoxidized material) in a loamy glacial till (K range from 10?6 to 10?9 m s?1). Piezometers were purged between 9 and 11 times for sampling over a period of five months. The effect of the purgings on piezometer development was evaluated by changes in slope of the water level recovery curves which were used to calculate hydraulic conductivity. The first five purgings following piezometer installation increased K in the 15 piezometers by an average of 34%. The average increase in a value of K after 10 purgings was 44%. Values measured for hydraulic conductivity in a 75 mm diameter auger hole appeared stable after four purgings but piezometers installed in larger diameter boreholes (100 mm to 280 mm) snowed increases in K with up to 10 purgings. The hydraulic conductivity determined for piezometers installed at a 30° angle to the vertical showed greater variability than was observed in the adjacent vertically installed piezometers at the same depth.  相似文献   

12.
A simple, inexpensive sampling pump has lately come into use in ground water monitoring. The pump is referred to as an inertial pump; its only downhole components are a foot valve connected to a length of tubing or pipe. The operating principle of the pump is based on the inertia of a column of water within the riser tubing. Ground water is drawn through the foot valve and up the riser tubing by rapid up and down movements of the tubing. This pumping method is not new, but has only recently been applied to monitoring wells. Foot valves are available in a variety of materials and sizes and can be used in monitoring wells as small as 19mm (3/4 inch) I.D. Flexible polyethylene or Teflon® tubing, and in some cases stainless steel tubing or rigid PVC pipe, is used as the riser. The inertial pump satisfies most of the criteria normally cited for an "ideal" sampling device. The pump is easy to operate, reliable, durable, portable, and virtually maintenance-free. It can be operated manually from as deep as 40m or from as deep as 60m using a motor drive. The pump is inexpensive, and therefore suitable for use as a dedicated sampling pump. Recent tests have shown the pump to be suitable for sampling volatile organics. The inertial pump has a high flow capacity and performs well in silty/sandy environments, which makes it useful for developing and purging monitoring wells. It may also be used to perform field hydraulic conductivity tests.  相似文献   

13.
Model ground water ages based on chlorofluorocarbons (CFCs) and tritium/helium-3 (3H/3He) data were obtained from two arrays of nested piezometers located on the north limb of an anticline in fractured sedimentary rocks in the Valley and Ridge geologic province of Pennsylvania. The fracture geometry of the gently east plunging fold is very regular and consists predominately of south dipping to subhorizontal to north dipping bedding-plane parting and east striking, steeply dipping axial-plane spaced cleavage. In the area of the piezometer arrays, which trend north-south on the north limb of the fold, north dipping bedding-plane parting is a more dominant fracture set than is steeply south dipping axial-plane cleavage. The dating of ground water from the piezometer arrays reveals that ground water traveling along paths parallel to the dip direction of bedding-plane parting has younger 3H/3He and CFC model ages, or a greater component of young water, than does ground water traveling along paths opposite to the dip direction. In predominantly unmixed samples there is a strong positive correlation between age of the young fraction of water and dissolved sodium concentration. The travel times inferred from the model ages are significantly longer than those previously calculated by a ground water flow model, which assumed isotropically fractured layers parallel to topography. A revised model factors in the directional anisotropy to produce longer travel times. Ground water travel times in the watershed therefore appear to be more influenced by anisotropic fracture geometry than previously realized. This could have significant implications for ground water models in other areas underlain by similarly tilted or folded sedimentary rock, such as elsewhere in the Valley and Ridge or the early Mesozoic basins.  相似文献   

14.
Ground water remediation of volatile organic compound (VOC) contamination at a site in Michigan was initiated as a result of a consent agreement between the Michigan Department of Natural Resources (MDNR) and the responsible party. Under the direction of the MDNR, the responsible party conducted a remedial investigation/feasibility study using federal guidelines to define the extent of contamination at the site and to select a response action for site remediation. The selected alternative included a combination of ground water extraction, treatment, and recharge, and soil flushing. The extraction system withdraws ground water from various depths in heavily contaminated areas. The ground water is treated using an air stripper. A spray distribution system spreads effluent from the stripper over a recharge basin constructed over the most contaminated areas. Additional contaminant removal is achieved by volatilization from the spray and percolation through the gravel bed. Recharge water moves downward through the contaminated soils, thus flushing residual soil contaminants. The initial operating data demonstrated that the system can effectively remove trichloroethylene (TCE) from ground water (approximately 95 percent overall removal efficiency). The annualized capital and operation and maintenance (O & M) costs of the remedial action were estimated for several operating periods (15, 20, and 30 years).  相似文献   

15.
Grout curtains are vertical grout walls installed in the ground. In karst terrains, their construction is primarily connected with dams and reservoirs. Their main role is to increase water tightness and to prevent progressive erosion, blocking possible seepage paths along karst fissures and conduits. In this article, changes in the behaviour of the groundwater level (GWL) and the water temperature in nine deep piezometers, which were caused by the construction of a grout curtain at the ?ale Reservoir on the Cetina River (Croatia), were analysed. The total length of the grout curtain is 3966 m. It spreads 120 m below the dam. The most analysed data are from the period after the dam had been built. Only few data and figures concern the comparison between pre‐ and post‐dam periods. The hourly data of the GWL and the water temperature were analysed for the period between 1 September 2008 at 02:00 h to 31 December 2009 at 23:00 h (11 687 h total) in six deep piezometers (marked in the text and figures as 1, 2, 3, 4, 5 and 6). For three piezometers (marked in the text and figures as A, B and C), some discontinuous measurements of the GWL and the water temperature were available for analysis. The construction of the grout curtain made strong, sudden and possibly dangerous changes to the characteristics of the aquifer and the circulation of groundwater in the local area. Special attention is paid to analyses of the behaviour of the hourly GWL data measured in the piezometers pairs (two neighbouring piezometers, one inside and the other outside of the grout curtain). During more than 80% of the analysed period, the GWL was higher in the piezometer inside the grout curtain than the one outside of it. The intensity and range of the dynamics of GWL was higher in piezometer outside the grout curtain than the inside ones. After the construction of the grout curtain, the maximum measured hydrostatic pressure on some parts of the grout curtain was approximately 40 m. It changes quickly in both time and direction. The water temperature was found to be similar in all of the measured piezometers, and it varies between 10.2 and 15.7 °C with an average value of 12.7 °C. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

16.
Waste disposal sites with volatile organic compounds (VOCs) frequently contain contaminants that are present in both the ground water and vadose zone. Vertical sampling is useful where transport of VOCs in the vadose zone may effect ground water and where steep vertical gradients in chemical concentrations are anticipated. Designs for combination ground water and gas sampling wells place the tubing inside the casing with the sample port penetrating the casing for sampling. This physically interferes with pump or sampler placement. This paper describes a well design that combines a ground water well with gas sampling ports by attaching the gas sampling tubing and ports to the exterior of the casing. Placement of the tubing on the exterior of the casing allows exact definition of gas port depth, reduces physical interference between the various monitoring equipment, and allows simultaneous remediation and monitoring in a single well. The usefulness and versatility of this design was demonstrated at the Idaho National Engineering and Environmental Laboratory (INEEL) with the installation of seven wells with 53 gas ports, in a geologic formation consisting of deep basalt with sedimentary interbeds at depths from 7.2 to 178 m below land surface. The INEEL combination well design is easy to construct, install, and operate.  相似文献   

17.
In these studies, the efficiency of various decontamination protocols was tested on small pieces of materials commonly used in ground water sampling devices. Three materials, which ranged in ability to sorb organic solutes, were tested: stainless steel (SS), rigid polyvinyl chloride (PVC), and polytetrafluoroethylene (PTFE). The test pieces were exposed to two aqueous test solutions: One contained three volatile organic compounds (VOCs) and one nitroaromatic compound, and the other contained four pesticides. Also, three types of polymeric tubing were exposed to pesticide solutions. Generally, the contact times were 10 minutes and 24 hours for sorption and desorption.
The contaminants were removed from the nonpermeable SS and the less-sorptive rigid PVC test pieces simply by washing with a hot detergent solution and rinsing with hot water. Additional treatment was required for the PTFE test pieces exposed to the VOCs and for the low-density polyethylene (LDPE) tubing exposed to the pesticide test solution. Solvent rinsing did not improve removal of the three VOCs from the PTFE and only marginally improved removal of the residual pesticides from the LDPE. However, a hot water and detergent wash and rinse followed by oven drying at approximately 105°C was effective for removing the VOCs from the PTFE and substantially reduced pesticide contamination from the LDPE.  相似文献   

18.
The principal difficulties with determinations of volatile organic compounds (VOCs) in ground water are the reliability of sampling procedures and analytical methods. Two integrated methods have been developed for routine sampling, processing, and analysis of VOCs in ground water. These methods involve in situ collection of ground water using a modified syringe sampler from PVC piezometers or using dedicated glass syringes from stainless steel multilevel bores. The samples are processed in the syringe using purge and trap or microsolvent extraction and analyzed by GC/MSD.
The modified purge-and-trap method is time-consuming and limited to volatile organic compounds. However, it is extremely sensitive and flexible: the volume of sample used can be varied by the use of different-size glass syringes (sample volumes from 1 to 100 mL).
In cases where extremely low sensitivity (<10 mg 1−1) is not critical, the microextraction technique is a more cost-effective method, allowing twice as many samples to be analyzed in the same time as the purge-and-trap method. It enables less volatile compounds such as polynuclear aromatic hydrocarbons, phenol, and cresols to be analyzed in the same GC run. Also, the microextraction method can be used in the field to avoid delays associated with transportation of ground water samples to the laboratory.  相似文献   

19.
Loss of volatile organics during sampling is a well-recognized source of bias in ground water monitoring; sampling protocols attempt to minimize such loss. Such bias could be enhanced for ground water highly charged with dissolved gases such as methane. Such ground water was the object of this study. A positive-displacement bladder pump, a momentum-lift pump and a suction-lift, peristaltic pump were employed in sampling both methane-charged ground water for volatile aromatic hydrocarbons and a CO2-charged reservoir water for volatile chlorinated hydrocarbons. In both cases, the suction-lift pump produced samples with a significant negative bias (9 to 33 percent) relative to the other methods. Little difference between samples produced by the other pump Systems was noted at the field site, but in sampling the reservoir, the bladder pump produced samples that were 13 to 19 percent lower in halocarbon concentration than were samples from the momentum-lift pump.
These negative biases are tentatively interpreted as losses due to volatilization during sampling. Slightly greater negative biases occur for compounds of higher volatility as estimated from their Henry's law constants. Additional studies appear to be warranted in order to adequately establish the scientific basis for recommending protocols for sampling ground water in which degassing could enhance the loss of volatile organics during sampling.  相似文献   

20.
A single-hole multilevel sampling piezometer system (MLSPS) has been designed by the Geological Survey of Canada (GSC) to be installed using drilling systems that continuously core (e.g., Rotosonic) or continuously sample (e.g., hollow-stem auger, Becker hammer) overburden and that have the flexibility of allowing additional coring (diamond drilling) or sampling (hammer drilling) of bedrock. The GSC-MLSPS (under license to Solinst Canada Ltd.) uses a patented GSC dry injection system for accurate emplacement of filter packs and seals. This system permits (a) the use of variable screen lengths; (b) the complete evacuation of piezometers before introduction of new ground water (no bailing); (c) the use of a number of types of hydraulic tests (e.g., slug, withdrawal/recovery, vacuum, pressure-pulse); (d) ground water sampling under a nitrogen atmosphere; (e) dissolved gas sampling; (f) a great deal of flexibility in the use of design materials; and (g) the elimination of bridging and collapse of filter packs and seals.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号