共查询到18条相似文献，搜索用时 187 毫秒
1.
半无限横观各向同性介质中多裂纹相互作用分析 总被引：2，自引：0，他引：2
为评估含矩形裂纹的半无限横观各向同性介质的局部强度和稳定性,采用基于双横观各向同性材料基本解的对偶边界元数值方法,分析了在沿裂纹面法向和切向均布力分别作用下矩形裂纹的应力强度因子及两个共面或平行的矩形裂纹的相互作用问题。通过数值计算考察了自由面对应力强度因子值的影响,以及裂纹间距、边长比及自由面对共面或平行双裂纹相互作用效应的影响。结果表明,自由面的存在引起该类裂纹应力强度因子值大于无限域情况;裂纹形状和裂纹间距对共面或平行双裂纹相互作用效应均有较明显的影响,但自由面对共面或平行双裂纹的相互作用效应均影响较小。 相似文献
2.
由于沉积等作用使得天然土材料内部颗粒排列表现为各向异性。土材料的各向异性使得材料内各平面滑动的内摩擦角不同。因此,在分析各向异性土的破坏问题中,除了考虑来自外部的应力分布以外,还需考虑土材料内部的强度分布。以横观各向同性土为例,阐述了同时考虑材料外部应力分布与材料内部强度分布下各向异性土的破坏机制。为说明,文中假定横观各向同性土内部各平面的内摩擦角正切值随空间方向而线性分布。外部加载进行时,横观各向同性土材料内部各处的应力不断变化,当其内部某处首次出现的应力达到该处的强度时,土材料发生破坏。进一步通过类比得出：区别于金属,各向同性土不是在最大剪应力面而是在最大剪压比面发生破坏;区别于各向同性土,各向异性土不是在最大剪压比面而是在最大剪压强比面发生破坏。 相似文献
3.
4.
模拟三维裂纹问题的扩展有限元法 总被引：4，自引：1，他引：3
扩展有限元法是一种在常规有限元框架内求解强和弱不连续问题的新型数值方法,其计算网格与不连续面相互独立,因此模拟移动不连续面时无需对网格进行重新剖分。给出了模拟三维裂纹问题的扩展有限元法。在常规有限元位移模式中,基于单位分解的思想加进一个阶跃函数和二维渐近裂尖位移场,反映裂纹处位移的不连续性。用两个水平集函数表示裂纹。采用线性互补法求解裂纹面非线性接触条件,不需要迭代,提高了计算效率。采用两点位移外推法计算裂纹前缘应力强度因子。给出了3个三维弹性静力问题算例,其结果显示了所提方法能获得高精度的应力强度因子,并能有效地处理裂纹面间的接触问题,同时表明扩展有限元结合线性互补法求解不连续问题具有较好的前景。 相似文献
5.
采用修正应力法考虑各向异性对土的抗剪强度的影响,该方法引入组构张量调整不同方向应力分量的相对大小,使得各向异性土在修正应力空间中等效成各向同性土。用修正应力张量代替真实应力张量,就能将摩尔-库仑强度准则发展至横观各向同性,公式的形式不发生改变,强度参数仍为与加载方向无关的常量。通过对比根据3种不同的修正应力公式得到的内摩擦角与加载方向的关系曲线,分析了组构值对内摩擦角变化规律的影响,在偏平面上绘出了连续规则的强度包线,并预测了不同各向异性岩土类材料的三轴压缩和真三轴试验结果。最后,根据横观各向同性摩尔-库仑准则计算水平沉积地层中挡土墙上的被动土压力,得到了简洁的显式表达式,验证了修正应力法的实用性。 相似文献
6.
针对线弹性断裂力学问题,提出扩展径向点插值无网格法（X-RPIM）。该方法基于单位分解思想,在传统径向点插值无网格法的位移模式中加入扩展项来描述裂纹两侧的不连续位移场和裂尖奇异场。由于其形函数具有Kronecker ? 函数性质,易于施加本质边界条件。详细描述了X-RPIM不连续位移模式的建立,支配方程的离散形式以及J积分计算混合模式裂纹的应力强度因子的实现过程,讨论了不同积分区域对应力强度因子的影响。数值算例分析证明了该方法在求解断裂问题时的可行性和有效性,同时说明扩展径向点插值无网格法在模拟裂纹扩展问题时具有良好的前景。 相似文献
7.
考虑裂隙水压力的岩体压剪裂纹扩展规律研究 总被引：3，自引：2，他引：1
在库水位大幅度升、降变化时,容易导致岩体内增量裂隙压力的集中,使断裂面上有效应力降低,裂纹面尖端的应力强度因子增加。当达到临界强度因子时,可能使岩体内裂纹、裂隙贯通、扩展,形成连续的复式破坏面,从而使边坡稳定性降低,造成边坡的失稳。基于此,从断裂力学角度分析了裂隙水压力对裂纹强度因子的影响,对考虑裂隙水压力作用的Ⅰ、Ⅱ型复合裂纹扩展规律进行了研究,结果表明：Ⅰ、Ⅱ型复合裂纹的裂纹扩展角的变化,不仅与裂纹的闭合程度、斜裂纹倾角、双向应力大小有关,还与裂隙水压力的大小、裂纹面的摩擦系数有关;并且在相同情况下,未闭合裂纹的扩展角要大于闭合裂纹的扩展角;对于闭合裂纹,裂纹面摩擦系数越小,扩展角越大;最后,推导了基于摩尔-库仑准则考虑裂隙水压力的岩体断裂韧度KIc、KIIc和压剪状态下Ⅰ、Ⅱ型复合断裂判据。研究成果为分析水岩作用下裂隙岩体的失稳破坏提供了重要的参考。 相似文献
8.
断裂问题的扩展有限元法研究 总被引：3，自引：0，他引：3
扩展有限元（extended finite element method,XFEM）是近年来发展起来的、在常规有限元框架内求解不连续问题的有效数值计算方法,其基于单位分解的思想,在常规有限元位移模式中加入能够反映裂纹面不连续性的跳跃函数及裂尖渐进位移场函数,避免了采用常规有限元计算断裂问题时需要对裂纹尖端重新加密网格造成的不便。在推导扩展有限元算法的基础上,分析了应力强度因子的J积分计算方法及积分区域的选取。采用XFEM对I型裂纹进行了计算,有限元网格独立于裂纹面,无需在裂纹尖端加密网格;分析了积分区域、网格密度对应力强度因子计算精度的影响,指出了计算应力强度因子的合适参数,验证了此方法的可靠性和准确性。 相似文献
9.
10.
层状岩体由于层理面或者结构面的存在,在力学上具有横观各向同性的特点,现有的各向同性蠕变模型难以全面反映横观各向同性岩体的蠕变力学特性。为构建能够反映横观各向同性岩体的三维蠕变模型,以能反映瞬时应变、减速蠕变和稳态蠕变特征的黏弹性Burgers模型为基础,基于常泊松比假定,在三维各向同性蠕变本构方程的基础上,按照算子替换的方法,将横观各向同性柔度矩阵代替各向同性柔度矩阵,并考虑了平行和垂直层理方向岩体蠕变力学行为的差异性,推导了横观各向同性岩体的三维蠕变本构方程。根据本构方程的特点,提出了根据平行和垂直方向岩体蠕变试验结果进行三维蠕变本构模型中蠕变参数的辨识方法。将提出的模型应用于三轴蠕变试验参数辨识,从而获得了一套完整的三维蠕变参数,并与试验结果进行对比分析,从而验证了所提模型与方法的合理性和有效性。进一步,指出了传统蠕变试验设计方案的局限性,给出了横观各向同性材料蠕变试验设计建议。研究成果为研究岩体三维蠕变机制提供了新思路,可对岩体蠕变试验设计提供相应的科研支撑。 相似文献
11.
Omid Saeidi Vamegh Rasouli Rashid Geranmayeh Vaneghi Raoof Gholami Seyed Rahman Torabi 《地学前缘(英文版)》2014,5(2):215-225
A modified failure criterion is proposed to determine the strength of transversely isotropic rocks. Me-chanical properties of some metamorphic and sedimentary rocks including gneiss, slate, marble, schist, shale, sandstone and limestone, which show transversely isotropic behavior, were taken into consider-ation. Afterward, introduced triaxial rock strength criterion was modified for transversely isotropic rocks. Through modification process an index was obtained that can be considered as a strength reduction parameter due to rock strength anisotropy. Comparison of the parameter with previous anisotropy in-dexes in literature showed reasonable results for the studied rock samples. The modified criterion was compared to modified Hoek-Brown and Ramamurthy criteria for different transversely isotropic rocks. It can be concluded that the modified failure criterion proposed in this study can be used for predicting the strength of transversely isotropic rocks. 相似文献
12.
L. CUI A. H. D. CHENG V. N. KALIAKIN Y. ABOUSLEIMAN J.-C. ROEGIERS 《国际地质力学数值与分析法杂志》1996,20(6):381-401
The finite element equations for non-linear, anisotropic poroelasticity are cast in the form of measurable engineering constants. Two problems of importance to the rock and petroleum industry are analysed by the FEM. First, the classical Mandel's problem with an extension to transversely isotropic case is investigated. Second, the problem of an inclined borehole is explored. In particular, the effect of material anisotropy on stress concentration near the wall with implication to borehole instability is examined in detail. 相似文献
13.
Elastic closed-form solutions for the displacements and stresses in a transversely isotropic half-space subjected to various buried loading types are presented. The loading types include finite line loads and asymmetric loads (such as uniform and linearly varying rectangular loads, or trapezoidal loads). The planes of transverse isotropy are assumed to be parallel to its horizontal surface. These solutions are directly obtained from integrating the point load solutions in a transversely isotropic half-space, which were derived using the principle of superposition, Fourier and Hankel transformation techniques. The solutions for the displacements and stresses in transversely isotropic half-spaces subjected to linearly variable loads on a rectangular region are never mentioned in literature. These exact solutions indicate that the displacements and stresses are influenced by several factors, such as the buried depth, the loading types, and the degree and type of rock anisotropy. Two illustrative examples, a vertical uniform and a vertical linearly varying rectangular load acting on the surface of transversely isotropic rock masses, are presented to show the effect of various parameters on the vertical surface displacement and vertical stress. The results indicate that the displacement and stress distributions accounted for rock anisotropy are quite different for those calculated from isotropic solutions. Copyright © 1999 John Wiley & Sons, Ltd. 相似文献
14.
In this paper, a single-region boundary element method (BEM) is presented for the analysis of transversely isotropic bi-material halfspaces with arbitrarily inclined planes of isotropy and material interfaces. The proposed BEM uses the fundamental solution of a transversely isotropic bi-material fullspace and five boundary element techniques. Infinite boundary elements are introduced to consider the far-fields of a transversely isotropic bi-material halfspace. The effective integration methods are proposed for dealing with various integrals in the discretized boundary integral equation. The stresses at internal points are obtained using the coordinate transformation of kernel functions, and the stresses on the boundary surface are calculated using an improved traction recovered method. Numerical verifications of displacements and stresses for a benchmark problem are conducted, and excellent agreement with previously published results is obtained. Numerical examples are presented to illustrate the influence of non-horizontal or horizontal planes of isotropy in bi-material halfspaces on the displacements and stresses induced by the tractions on the horizontal boundary surface. Results reveal that the elastic fields vary clearly with the dip angle of the isotropic plane and the stresses across the bi-material interface are closely related to the ratios of the elastic parameters of the bi-material. 相似文献
15.
This paper presents the development of a three-dimensional discrete element model using flat-joint and smooth-joint contact models to investigate the effect of anisotropy on the tensile behaviour of slate, a transversely isotropic rock, under Brazilian testing from both macro and microscales. The effect of anisotropy is further realised by exploring the influence of foliation orientations (β and ψ) on the tensile strength, fracture pattern, microcracking and stress distribution of the transversely isotropic rock. The variation of tensile strength with foliation orientation is presented. The cross-weak-plane fracture growth observed in laboratory is reproduced, and the criterion for which to form is also given from the aspect of foliation orientation. Furthermore, the proportional variations of microcracks well account for the effects of foliation orientation on the tensile strength and failure pattern. Finally, it is found that the existence of weak planes increases both the heterogeneity and the anisotropy of stress distributions within the transversely isotropic rock, with the degree of influence varying with the foliation orientation. 相似文献
16.
We rederive and present the complete closed-form solutions of the displacements and stresses subjected to a point load in a transversely isotropic elastic half-space. The half-space is bounded by a horizontal surface, and the plane of transverse isotropy of the medium is parallel to the horizontal surface. The solutions are obtained by superposing the solutions of two infinite spaces, one acting a point load in its interior and the other being free loading. The Fourier and Hankel transforms in a cylindrical co-ordinate system are employed for deriving the analytical solutions. These solutions are identical with the Mindlin and Boussinesq solutions if the half-space is homogeneous, linear elastic, and isotropic. Also, the Lekhnitskii solution for a transversely isotropic half-space subjected to a vertical point load on its horizontal surface is one of these solutions. Furthermore, an illustrative example is given to show the effect of degree of rock anisotropy on the vertical surface displacement and vertical stress that are induced by a single vertical concentrated force acting on the surface. The results indicate that the displacement and stress accounted for rock anisotropy are quite different for the displacement and stress calculated from isotropic solutions. © 1998 John Wiley & Sons, Ltd. 相似文献
17.
Existing solutions to Mandel's problem focus on isotropic, transversely isotropic, and orthotropic materials, the last two of which have one of the material symmetry axes coincide with the vertical loading direction. The classical plane strain condition holds for all these cases. In this work, analytical solution to Mandel's problem with the most general matrix anisotropy is presented. This newly derived analytical solution for fully anisotropic materials has all the three nonzero shear strains. Warping occurs in the cross sections, and a generalized plane strain condition is fulfilled. This solution can be applied to transversely isotropic and orthotropic materials whose material symmetry axes are not aligned with the vertical loading direction. It is the first analytical poroelastic solution considering mechanical general anisotropy of elasticity. The solution captures the effects of material anisotropy and the deviation of the material symmetry axes from the vertical loading direction on the responses of pore pressure, stress, strain, and displacement. It can be used to match, calibrate, and simulate experimental results to estimate anisotropic poromechanical parameters. This generalized solution is capable of reproducing the existing solutions as special cases. As an application, the solution is used to study the responses of transversely isotropic and orthotropic materials whose symmetry axes are not aligned with the vertical loading direction. Examples on anisotropic shale rocks show that the effects of material anisotropy are significant. Mandel-Cryer's effects are highly impacted by the degree of material anisotropy and the deviation of the material symmetry axes from the vertical loading direction. 相似文献
18.
In many areas of engineering practice, applied loads are not uniformly distributed but often concentrated towards the centre of a foundation. Thus, loads are more realistically depicted as distributed as linearly varying or as parabola of revolution. Solutions for stresses in a transversely isotropic half‐space caused by concave and convex parabolic loads that act on a rectangle have not been derived. This work proposes analytical solutions for stresses in a transversely isotropic half‐space, induced by three‐dimensional, buried, linearly varying/uniform/parabolic rectangular loads. Load types include an upwardly and a downwardly linearly varying load, a uniform load, a concave and a convex parabolic load, all distributed over a rectangular area. These solutions are obtained by integrating the point load solutions in a Cartesian co‐ordinate system for a transversely isotropic half‐space. The buried depth, the dimensions of the loaded area, the type and degree of material anisotropy and the loading type for transversely isotropic half‐spaces influence the proposed solutions. An illustrative example is presented to elucidate the effect of the dimensions of the loaded area, the type and degree of rock anisotropy, and the type of loading on the vertical stress in the isotropic/transversely isotropic rocks subjected to a linearly varying/uniform/parabolic rectangular load. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献