共查询到20条相似文献，搜索用时 15 毫秒
1.
This paper investigates the performance of a small axisymmetric buoy under wave-by-wave near optimal control in surge, heave, and pitch modes in long-crested irregular waves. Wave prediction is obtained using a deterministic propagation model. The paper describes the overall formulation leading up to the derivation of the feedforward control forces in surge and heave, and the control moment in pitch. The radiation coupling between surge and pitch modes is accounted for in the model. Actuation is relative to deeply submerged reaction masses. Heave oscillations are constrained by the swept-volume limit. Oscillation constraints are also applied on the surge and pitch oscillations. The paper discusses time-domain simulations for an irregular wave input with and without the present control. Also discussed are results obtained over a range of irregular wave conditions derived for energy periods from 7 s to 17 s, and a significant wave height of 1 m. It is found that, while the gains in power capture enabled by the present control are significant, the actuation forces are also very large, given the small size of the buoy. Further, due to the small size, heave is found to be the dominant contributor to power capture, with relatively modest contributions from surge and pitch. 相似文献
2.
K.R. Drake 《Ocean Engineering》2011,38(5-6):810-814
An analytical solution is presented for the horizontal drift force acting on a uniform circular cylinder that is undergoing surge and pitch motion in regular waves. The solution is exact to second order, for a perturbation expansion in terms of wave steepness, but is limited in a strict sense to the hypothetical case when the draught is equal to the water depth. The formulation is used to provide an analytical approximation for investigating the influence of key parameters on the horizontal drift force acting on a deep draught spar. 相似文献
3.
Interactions between water waves and non-wall-sided cylinders are analyzed based on velocity potential theory with fully nonlinear boundary conditions on the free surface and the body surface. The finite element method (FEM) is adopted together with a 3D mesh generated through an extension of a 2D Delaunay grid on a horizontal plane along the depth. The linear matrix equation for the velocity potential is constructed by imposing the governing equation and boundary conditions through the Galerkin method and is solved through an iterative method. By imposing the gradient of the potential equal to the velocity, the Galerkin method is used again to obtain the velocity field in the fluid domain. Simulations are made for bottom mounted and truncated cylinders with flare in a numerical tank. Periodic waves and wave groups are generated by a piston type wave maker mounted on one end of the tank. Results are obtained for forces, wave profiles and wave runups. Further simulations are made for a cylinder with flare subjected to forced motion in otherwise still open water. Results are provided for surge and heave motion in different amplitudes, and for a body moving in a circular path in the horizontal plane. Comparisons are made in several cases with the results obtained from the second order solution in the time domain. 相似文献
4.
To assist in the prototyping and controller design of point-absorber wave energy converters (WECs), an easy-to-implement hybrid integral-equation method is presented for computing the frequency-domain hydrodynamic properties of bodies with a vertical axis of symmetry in waves. The current hybrid method decomposes the flow domain into two parts: an inner domain containing the body and an outer domain extending to infinity. The solution in the inner domain is computed using the boundary-element method, and the outer-domain solution is expressed using eigenfunctions. Proper matching at the domain boundary is achieved by enforcing continuity of velocity potential and its normal derivative. Body symmetry allows efficient computation using ring sources in the inner domain. The current method is successfully applied to three different body geometries including a vertical truncated floating cylinder, the McIver toroid, and the coaxial-cylinder WEC being developed in the authors’ laboratory. In particular, the current results indicate that, by replacing the flat bottom of the coaxial-cylinder WEC with the Berkeley-Wedge (BW) shape, viscous effect can be significantly reduced with only minor negative impact on wave-exciting force, thus increasing WEC efficiency. Finally, by comparing to experimental measurements, the current method is demonstrated to accurately predict the heave added mass and wave-exciting force on the coaxial-cylinder WEC with BW geometry. If a viscous damping correction factor is used, the heave motion amplitude can also be accurately computed. 相似文献
5.
6.
This paper investigates wave-by-wave control of a wave energy converter using incident wave prediction based on up-wave surface elevation measurement. The goal of control is to approach the hydrodynamically optimum velocity leading to optimum power absorption. This work aims to study the gains in energy conversion from a deterministic wave propagation model that accounts for a range of group velocities in deriving the prediction. The up-wave measurement distance is assumed to be small enough to allow a deterministic propagation model, and further, both wave propagation and device response are assumed to be linear. For deep water conditions and long-crested waves, the propagation process is also described using an impulse response function (e.g. [1]). Approximate low and high frequency limits for realistic band-limited spectra are used to compute the corresponding group velocity limits. The prediction time into the future is based on the device impulse response function needed for the evaluation of the control force. The up-wave distance and the duration of measurement are then determined using the group velocity limits above.A 2-body axisymmetric heaving device is considered, for which power capture is through the relative heave oscillation between the two co-axial bodies. The power take-off is assumed to be linear and ideal as well as capable of applying the necessary resistive and reactive load components on the relative heave oscillation. The predicted wave profile is used along with device impulse response functions to compute the actuator force components at each instant. Calculations are carried out in irregular waves generated using a number of uni-modal wave spectra over a range of energy periods and significant wave heights. Results are compared with previous studies based on the use of instantaneous up-wave wave-profile measurements, both without and with oscillation constraints imposed. Considerable improvements in power capture are observed with the present approach over the range of wave conditions studied. 相似文献
7.
基于细长体水动力模型比较了Truss Spar平台在波流联合作用下运动响应预报的三种方法。分别采用波流耦合、速度叠加及力叠加计算Truss Spar平台在波流联合作用下的水动力载荷,根据流场水质点运动规律和Truss Spar外部形状特点,分段高效计算水动力载荷。利用Runge-Kutta-Fehlberg方法求解刚体非线性运动方程得Truss Spar在波流场中的运动响应。研究结果表明力叠加法所预报的Truss Spar纵荡和纵摇运动明显大于其他两种方法的相应运动响应预报结果,而波流耦合法与速度叠加法所预报的纵荡与纵摇运动响应幅值相当,三种方法所预报的垂荡运动响应的大小取决于具体波流参数。 相似文献
8.
The paper provides a detailed analysis for the second-order diffraction of monochromatic waves. For the second-order potential on the free surface, the paper proposed a forward prediction method for computing the integration on the free surface. By this method we only need to run the infinity integration on the free surface directly for a few points; a one-step quadrature can then be applied successively outward from the body for potentials at other points. For wave diffraction from a body of revolution with a vertical axis, the paper derives a new integral equation, which can cancel the leading singularity in the derivative of ring Green's functions automatically. To obtain accurate results, different approaches are also used to deal with singularities in the ring Green's functions in the integration on both the body surface and free surface. The method has been implemented for bodies of revolution with vertical axes, but the theory is also available for arbitrary bodies.A numerical examination is made to validate the numerical code by comparing the second-order forces and moments on uniform and truncated cylinders and second-order diffraction potentials on the free surface with some published results. The comparison shows that the present results are in good agreement with those published. The method is also used to compute the second-order wave elevation around uniform and truncated cylinders. 相似文献
9.
In this study, a two-dimensional floating pier consists of single rectangular impermeable pontoon with side supporting pile-columns is studied. The purpose of this study is to present a theoretical solution for the linearized problem of incident waves exerting on a floating pier with pile-restrained. All boundary conditions are linearized in the problem, which is incorporated into a scattering problem and radiation problem with unit displacement. The method of separation of variables is used to solve for velocity potentials. For the radiation problem with unit heave and pitch amplitude, the boundary value problem with non-homogeneous boundary condition beneath the structure is solved by using a solution scheme. By calculating the wave force from velocity potential and solving the equation of motion of the floating structure simultaneously a close form theoretical solution for the problem is developed. The finite element method was also applied to calculate the dynamic responses on the supporting piles subjected to the pontoon motions and incident waves. 相似文献
10.
《Ocean Engineering》2004,31(3-4):269-304
The paper seeks to apply the methodology of matched asymptotic expansions to obtain analytical solutions for hydrodynamic properties of a circular cylindrical platform (truncated circular cylinder) in extremely shallow water. By matching potentials of the fluid flows outside and under the cylinder bottom with the inner flow near its edge the radiation problems are solved for heave, surge and pitch motions. Closed asymptotic formulae are derived for all hydrodynamic coefficients of the floating cylinder, which include the first-order terms in the gap height. The formulae are discussed and shown to compare well with numerical results published in literature. 相似文献
11.
浅水破碎波对直立圆柱作用力的试验研究 总被引：2，自引：0，他引：2
分析了桩柱破波力的构成特性,认为破碎波与桩柱作用过程中在不完全绕流区将出现由于附连质量迅速变化引起的冲击力和柱前后波面高度差引起的附加压差力;影响破碎波对直立圆柱作用力的因素应该包括确定破波特性的水底坡度i、入射深水波陡H_0/L_0及代表圆柱对破波作用影响的相对柱径D/H_0。通过从i=1/100到1/15五种底坡上桩柱破波力的系统试验,探索了桩柱破波力的作用特性,归纳了计算桩柱破波力的经验公式。 相似文献
12.
The wave runup caused by a vertical cylinder surging in regular waves is studied both experimentally and numerically. The so-called DualSPHysics Smoothed Particle Hydrodynamics (SPH) code is used for the 3-D numerical modelling. A wide range of cylinder sizes and wave conditions is investigated with results comparing favourably between the experimental and SPH model under both fixed and forced-surge conditions. The experimental and SPH results are further used to predict the maximum runup amplification, in particular the ratio of the runup caused by the surging cylinder to that of the fixed, over the phase difference between the incident wave and surge motion. This maximum runup ratio has been analysed for its dependence on factors such as wave steepness, wave scattering and surge amplitude. An empirical equation is proposed for predicting the maximum runup ratio from known incident wave and surge conditions. Comparison with results from linear solvers suggests that the linear solvers under-predict the full nonlinear runup by a factor of 1.3–1.5. 相似文献
13.
The finite element method(FEM) is employed to analyze the resonant oscillations of the liquid confined within multiple or an array of floating bodies with fully nonlinear boundary conditions on the free surface and the body surface in two dimensions.The velocity potentials at each time step are obtained through the FEM with 8-node quadratic shape functions.The finite element linear system is solved by the conjugate gradient(CG) method with a symmetric successive overelaxlation(SSOR) preconditioner.The waves at the open boundary are absorbed by the combination of the damping zone method and the Sommerfeld-Orlanski equation.Numerical examples are given by an array of floating wedgeshaped cylinders and rectangular cylinders.Results are provided for heave motions including wave elevations,profiles and hydrodynamic forces.Comparisons are made in several cases with the results obtained from the second order solution in the time domain.It is found that the wave amplitude in the middle region of the array is larger than those in other places,and the hydrodynamic force on a cylinder increases with the cylinder closing to the middle of the array. 相似文献
14.
The diffraction of linear waves by a uniform vertical cylinder with cosine-type radial perturbations
The interaction of linear waves with a uniform, bottom-mounted, surface-piercing cylinder whose diameter exhibits a cosine-type variation is investigated. Two solution methods are presented. One method is based on a perturbation theory, using a perturbation parameter defined in terms of the surface geometry of the cylinder. The analysis includes terms up to the first-order in this parameter, where the zeroth-order solution corresponds to a circular cylinder. The velocity potentials at the zeroth and first orders are expressed as eigenfunction expansions involving unknown coefficients that are subsequently determined through the cylinder boundary conditions. The second method is based on Green's theorem and gives rise to an integral equation for the fluid velocity potential on the cylinder surface. A comparison between the results of these two methods has proved that they are in good agreement for small values of the perturbation parameter. Numerical results are presented that illustrate the influence of the magnitude and frequency of these perturbations on the resulting hydrodynamic force and the wave runup on the cylinder. 相似文献
15.
The finite element method (FEM) is employed to analyze the resonant oscillations of the liquid confined within multiple or an array of floating bodies with fully nonlinear boundary conditions on the free surface and the body surface in two dimensions. The velocity potentials at each time step are obtained through the FEM with 8-node quadratic shape functions. The finite element linear system is solved by the conjugate gradient (CG) method with a symmetric successive overelaxlation (SSOR) preconditioner. The waves at the open boundary are absorbed by the combination of the damping zone method and the Sommerfeld-Orlanski equation. Numerical examples are given by an array of floating wedge- shaped cylinders and rectangular cylinders. Results are provided for heave motions including wave elevations, profiles and hydrodynamic forces. Comparisons are made in several cases with the results obtained from the second order solution in the time domain. It is found that the wave amplitude in the middle region of the array is larger than those in other places, and the hydrodynamic force on a cylinder increases with the cylinder closing to the middle of the array. 相似文献
16.
Floating pontoon breakwaters 总被引：1，自引：0，他引：1
The hydrodynamic properties of a pair of long floating pontoon breakwaters of rectangular section are investigated theoretically. The structures are partially restrained by linear symmetric moorings fore and aft. The fluid motion is idealized as linearized, two-dimensional potential flow. The breakwater motions are assumed to be two-dimensional, in surge, heave and pitch. The solution for the fluid motion is obtained by the boundary integral equation method using an appropriate Green's function. Numerical results are presented that illustrate the effects of the various wave and structural parameters on the efficiency of the breakwaters as barriers to wave action. It is found that the wave reflection properties of the structures depend strongly on their width, draft and spacing and the mooring line stiffnesses, while their excess buoyancy is of lesser importance. 相似文献
17.
The substructures of offshore wind turbines are subjected to extreme breaking irregular wave forces. The present study is focused on investigating breaking irregular wave forces on a monopile using a computational fluid dynamics (CFD) based numerical model. The breaking irregular wave forces on a monopile mounted on a slope are investigated with a numerical wave tank. The experimental and numerical irregular free surface elevations are compared in the frequency-domain for the different locations in the vicinity of the cylinder. A numerical analysis is performed for different wave steepness cases to understand the influence of wave steepness on the breaking irregular wave loads. The wave height transformation and energy level evolution during the wave shoaling and wave breaking processes is investigated. The higher-frequency components generated during the wave breaking process are observed to play a significant role in initiating the secondary force peaks. The free surface elevation skewness and spectral bandwidth during the wave transformation process are analysed and an investigation is performed to establish a correlation of these parameters with the breaking irregular wave forces. The role of the horizontal wave-induced water particle velocity at the free surface and free surface pressure in determining the breaking wave loads is highlighted. The higher-frequency components in the velocity and pressure spectrum are observed to be significant in influencing the secondary peaks in the breaking wave force spectrum. 相似文献
18.
Floating wind turbine has been the highlight in offshore wind industry lately. There has been great effort on developing highly sophisticated numerical model to better understand its hydrodynamic behaviour. A engineering-practical method to study the nonlinear wave effects on floating wind turbine has been recently developed. Based on the method established, the focus of this paper is to quantify the wave nonlinearity effect due to nonlinear wave kinematics by comparing the structural responses of floating wind turbine when exposed to irregular linear Airy wave and fully nonlinear wave. Critical responses and fatigue damage are studied in operational conditions and short-term extreme values are predicted in extreme conditions respectively. In the operational condition, wind effects are dominating the mean value and standard deviation of most responses except floater heave motion. The fatigue damage at the tower base is dominated by wind effects. The fatigue damage for the mooring line is more influenced by wind effects for conditions with small wave and wave effects for conditions with large wave. The wave nonlinearity effect becomes significant for surge and mooring line tension for large waves while floater heave, pitch motion, tower base bending moment and pontoon axial force are less sensitive to the nonlinear wave effect. In the extreme condition, linear wave theory underestimates wave elevation, floater surge motion and mooring line tension compared with fully nonlinear wave theory while quite close results are predicted for other responses. 相似文献
19.
针对张力腿系泊浮式风力机的基础运动,忽略柔性构件的影响,建立气动—水动—系泊非线性耦合运动方程。在运动控制方程中包含张力腿系泊系统的非线性回复刚度,桨距角控制以及浮式基础运动对空气动力载荷的影响。在波浪载荷的计算中考虑二阶波浪载荷的作用。采用随机频率相位角调制法生成畸形波波面时历,计算在畸形波作用下张力腿型浮式风力机的动力响应特性。数值模拟结果表明,在畸形波作用下,浮式基础的运动及空气动力性能均受到了显著的影响。其中浮式基础的纵荡和纵摇运动分别受二阶差频与和频波浪力的影响,而垂荡运动的增加则主要是受下沉运动的影响。在畸形波经过的时刻,风力机的功率系数迅速下降,水平方向的风载荷波动先减小,随后其数值急剧下降,而垂直方向的风载荷波动增大。 相似文献
20.
The mooring of offshore floating structures, such as offshore platforms, in large waves against drift forces and rotational moments is a challenging problem in offshore engineering. To accurately investigate such problems, called positioning problems, the time-averaged steady forces of the second order known as the wave drift forces must be taken into account. Fortunately, a cloaking phenomenon occurs under certain conditions and dramatically reduces the wave drift force acting on such a floating body, as previously reported by several researchers. In the diffraction problem of water waves, cloaking refers to the condition where there is no scattering in the form of radial outgoing waves. The reduction of wave drift force on a truncated cylinder with the occurrence of cloaking phenomenon has been numerically and experimentally confirmed. In this paper, the arrangement of several small circular cylinders at regular intervals in a circle concentric with a fixed floating body is considered as an effective means of reducing the wave drift force. Using a combination of a higher-order boundary element method (HOBEM) and wave interaction theory, the influences of the geometric parameters of the outer surrounding cylinders on the wave drift force and the total scattered-wave energy are systematically investigated and discussed. A quasi-cloaking phenomenon is first found and reported in the present study, which is beneficial and flexible for application in practical engineering. More than one quasi-cloaking trigger (where a trigger is an occurrence condition) can be found simply by varying the distance between the inner and outer floating bodies. 相似文献