共查询到20条相似文献，搜索用时 15 毫秒
1.
A study on DEM-derived primary topographic attributes for hydrologic applications: Sensitivity to elevation data resolution 总被引：1，自引：0，他引：1
Primary topographic attributes play a critical role in determining watershed hydrologic characteristics for water resources modeling with raster-based digital elevation models (DEM). The effects of DEM resolution on a set of important topographic derivatives are examined in this study, including slope, upslope contributing area, flow length and watershed area. The focus of the study is on how sensitive each of the attributes is to the resolution uncertainty by considering the effects of overall terrain gradient and bias from resampling. Two case study watersheds of different gradient patterns are used with their 10 m USGS DEMs. A series of DEMs up to 200 m grid size are produced from the base DEMs using three commonly used resampling methods. All the terrain variables tested vary with the grid size change. It is found that slope angles decrease and contributing area values increase constantly as DEMs are aggregated progressively to coarser resolutions. No systematic trend is observed for corresponding changes of flow path and watershed area. The analysis also suggests that gradient profile of the watershed presents an important factor for the examined sensitivities to DEM resolution. 相似文献
2.
地形信息对确定DEM适宜分辨率的影响 总被引：2，自引：0，他引：2
分辨率会直接影响基于栅格数字高程模型（DEM）的数字地形分析结果,因此在实际应用中,需要选择适宜的DEM分辨率。目前采取的基本方法,基于某种地形信息定量刻画尺度效应曲线,从而确定DEM适宜分辨率,但对于采用不同地形信息时所产生的影响尚缺乏研究。本文针对该方法中通常采用的坡度、剖面曲率、水平曲率等3 种地形信息,每种地形信息提取时,分别使用两种不同的常用算法,在3 个不同地形特征的研究区中,逐一计算其在不同分辨率下的局部方差均值,以刻画尺度效应曲线,确定相应的DEM适宜分辨率,并进行对比分析。结果表明：① 采用剖面曲率或水平曲率所得适宜分辨率结果基本相同,但采用坡度所得出的适宜分辨率结果则有明显差别,后者所得的适宜分辨率更粗;② 采用不同地形信息时,越是在平缓地形为主的研究区,所得的适宜分辨率结果越相近,在复合地形特征的研究区所得到的适宜分辨率区间均明显较宽;③ 地形属性计算时所用的算法对适宜分辨率结果的影响不明显。 相似文献
3.
Monia Santini Salvatore Grimaldi Fernando Nardi Andrea Petroselli Maria Cristina Rulli 《Geomorphology》2009,113(1-2):110
Terrain analysis applications using remotely sensed Digital Elevation Models (DEMs), nowadays easily available, permit to quantify several river basin morphologic and hydrologic properties (e.g. slope, aspect, curvature, flow path lengths) and indirect hydrogeomorphic indices (e.g. specific upslope area, topographic wetness index) able to characterize the physical processes governing the landscape evolution (e.g. surface saturation, runoff, erosion, deposition). Such DEMs often contain artifacts and the automated hydrogeomorphic characterization of the watershed is influenced by terrain analysis procedures consisting in artificial depression (pit) and flat area treatment approaches combined with flow direction methods.In shallow landslide deterministic models, when applied using topographic dataset at medium scale (e.g. 30 m of resolution), the choice of the most suitable DEM-processing procedure is not trivial and can influence model results. This also affects the selection of most critical areas for further finer resolution studies or for the implementation of countermeasures aiming to landslide risk mitigation.In this paper such issue is investigated using as topographic input the ASTER DEMs and comparing two different combinations of DEM correction and flow routing schemes. The study areas comprise ten catchments in Italy for which hydrogeomorphic processes are significant. Aims of this paper are: 1) to introduce a parameter estimation procedure for the physically-based DEM correction method PEM4PIT (Physical Erosion Model for PIT removal); 2) to investigate the influence of different terrain analysis procedures on results of the slope stability model SHALSTAB (SHAllow Landsliding STABility) using remotely-sensed ASTER DEMs; 3) trying to assess which of terrain analysis methods is more appropriate for describing terrain instability. 相似文献
4.
不同分辨率DEM提取地面坡度的不确定性模拟:以在黄土高原的试验为例 总被引：1，自引：0，他引：1
Slope is one of the crucial terrain variables in spatial analysis and land use planning,especially in the Loess Plateau area of China which is suffering from serious soil erosion. DEM based slope extracting method has been widely accepted and applied in practice. However slope accuracy derived from this method usually does not match with its popularity. A quantitative simulation to slope data uncertainty is important not only theoretically but also necessarily to applications. This paper focuses on how resolution and terrain complexity impact on the accuracy of mean slope extracted from DEMs of different resolutions in the Loess Plateau of China. Six typical geomorphologic areas are selected as test areas, representing different terrain types from smooth to rough. Their DEMs are produced from digitizing contours of 1:10,000 scale topographic maps. Field survey results show that 5 m should be the most suitable grid size for representing slope in the Loess Plateau area. Comparative and math-simulation methodology was employed for data processing and analysis. A linear correlativity between mean slope and DEM resolution was found at all test areas,but their regression coefficients related closely with the terrain complexity of the test areas. If taking stream channel density to represent terrain complexity, mean slope error could be regressed against DEM resolution (X) and stream channel density (S) at 8 resolution levels and expressed as (0.0015S2+0.031S-0.0325)X-0.0045S2-0.155S+0.1625, with a R2 value of over 0.98. Practical tests also show an effective result of this model in applications. The new development methodology applied in this study should be helpful to similar researches in spatial data uncertainty investigation. 相似文献
5.
TANGGuoan ZHAOMudan LITianwen LIUYongmei ZHANGTing 《地理学报(英文版)》2003,13(4):387-394
Slope is one of the crucial terrain variables in spatial analysis and land use planning, especially in the Loess Plateau area of China which is suffering from serious soil erosion. DEM based slope extracting method has been widely accepted and applied in practice. However slope accuracy derived from this method usually does not match with its popularity. A quantitative simulation to slope data uncertainty is important not only theoretically but also necessarily to applications. This paper focuses on how resolution and terrain complexity impact on the accuracy of mean slope extracted from DEMs of different resolutions in the Loess Plateau of China. Six typical geomorphologic areas are selected as test areas, representing different terrain types from smooth to rough. Their DEMs are produced from digitizing contours of 1:10,000 scale topographic maps. Field survey results show that 5 m should be the most suitable grid size for representing slope in the Loess Plateau area. Comparative and math-simulation methodology was employed for data processing and analysis. A linear correlativity between mean slope and DEM resolution was found at all test areas, but their regression coefficients related closely with the terrain complexity of the test areas. If taking stream channel density to represent terrain complexity, mean slope error could be regressed against DEM resolution (X) and stream channel density (S) at 8 resolution levels and expressed as(0.0015S2 0.031S-0.0325)X-0.0045S2-0.155S 0.1625, with a R2 value of over 0.98. Practical tests also show an effective result of this model in applications. The new development methodology applied in this study should be helpful to similar researches in spatial data uncertainty investigation. 相似文献
6.
Slope is one of the crucial terrain variables in spatial analysis and land use planning, especially in the Loess Plateau area of China which is suffering from serious soil erosion. DEM based slope extracting method has been widely accepted and applied in practice. However slope accuracy derived from this method usually does not match with its popularity. A quantitative simulation to slope data uncertainty is important not only theoretically but also necessarily to applications. This paper focuses on how resolution and terrain complexity impact on the accuracy of mean slope extracted from DEMs of different resolutions in the Loess Plateau of China. Six typical geomorphologic areas are selected as test areas, representing different terrain types from smooth to rough. Their DEMs are produced from digitizing contours of 1:10,000 scale topographic maps. Field survey results show that 5 m should be the most suitable grid size for representing slope in the Loess Plateau area. Comparative and math-simulation methodology was employed for data processing and analysis. A linear correlativity between mean slope and DEM resolution was found at all test areas, but their regression coefficients related closely with the terrain complexity of the test areas. If taking stream channel density to represent terrain complexity, mean slope error could be regressed against DEM resolution (X) and stream channel density (S) at 8 resolution levels and expressed as (0.0015S2+0.031S-0.0325)X-0.0045S2-0.155S+0.1625, with a R2 value of over 0.98. Practical tests also show an effective result of this model in applications. The new development methodology applied in this study should be helpful to similar researches in spatial data uncertainty investigation. 相似文献
7.
Automated classifications of topography from DEMs by an unsupervised nested-means algorithm and a three-part geometric signature 总被引：7，自引：3，他引：7
An iterative procedure that implements the classification of continuous topography as a problem in digital image-processing automatically divides an area into categories of surface form; three taxonomic criteria–slope gradient, local convexity, and surface texture–are calculated from a square-grid digital elevation model (DEM). The sequence of programmed operations combines twofold-partitioned maps of the three variables converted to greyscale images, using the mean of each variable as the dividing threshold. To subdivide increasingly subtle topography, grid cells sloping at less than mean gradient of the input DEM are classified by designating mean values of successively lower-sloping subsets of the study area (nested means) as taxonomic thresholds, thereby increasing the number of output categories from the minimum 8 to 12 or 16. Program output is exemplified by 16 topographic types for the world at 1-km spatial resolution (SRTM30 data), the Japanese Islands at 270 m, and part of Hokkaido at 55 m. Because the procedure is unsupervised and reflects frequency distributions of the input variables rather than pre-set criteria, the resulting classes are undefined and must be calibrated empirically by subsequent analysis. Maps of the example classifications reflect physiographic regions, geological structure, and landform as well as slope materials and processes; fine-textured terrain categories tend to correlate with erosional topography or older surfaces, coarse-textured classes with areas of little dissection. In Japan the resulting classes approximate landform types mapped from airphoto analysis, while in the Americas they create map patterns resembling Hammond's terrain types or surface-form classes; SRTM30 output for the United States compares favorably with Fenneman's physical divisions. Experiments are suggested for further developing the method; the Arc/Info AML and the map of terrain classes for the world are available as online downloads. 相似文献
8.
基于高分辨率DEM的黄土地貌正负地形自动分割技术研究 总被引：4，自引：0，他引：4
黄土地貌正负地形自动分割是构建地表空间分布式机理-过程模型的基础。在分析黄土高原地区典型地貌坡面形态及汇流过程特征的基础上,提出了基于5m分辨率栅格DEM自动分割黄土正、负地形的技术方案。该方案首先利用坡面上下游栅格点的坡度对比识别沟沿线点,然后利用汇水模型提取沟沿线点约束的上游汇水区域,从而实现正、负地形的自动分割。在黄土塬区及丘陵沟壑区的实验结果表明,该方法的优点是提取精度高,人工干预少,在不同地貌类型区域内有很好的应用适宜性。 相似文献
9.
Objective landslide detection and surface morphology mapping using high-resolution airborne laser altimetry 总被引：6，自引：0，他引：6
A map of extant slope failures is the most basic element of any landslide assessment. Without an accurate inventory of slope instability, it is not possible to analyze the controls on the spatial and temporal patterns of mass movement or the environmental, human, or geomorphic consequences of slides. Landslide inventory maps are tedious to compile, difficult to make in vegetated terrain using conventional techniques, and tend to be subjective. In addition, most landslide inventories simply outline landslide boundaries and do not offer information about landslide mechanics as manifested by internal deformation features. In an alternative approach, we constructed accurate, high-resolution DEMs from airborne laser altimetry (LIDAR) data to characterize a large landslide complex and surrounding terrain near Christchurch, New Zealand. One-dimensional, circular (2-D) and spherical (3-D) statistics are used to map the local topographic roughness in the DEMs over a spatial scale of 1.5 to 10 m. The bedrock landslide is rougher than adjacent unfailed terrain and any of the statistics can be employed to automatically detect and map the overall slide complex. Furthermore, statistics that include a measure of the local variability of aspect successfully delineate four kinematic units within the gently sloping lower half of the slide. Features with a minimum size of surface folds that have a wavelength of about 11 to 12 m and amplitude of about 1 m are readily mapped. Two adjacent earthflows within the landslide complex are distinguished by a contrast in median roughness, and texture and continuity of roughness elements. The less active of the earthflows has a surface morphology that presumably has been smoothed by surface processes. The Laplacian operator also accurately maps the kinematic units and the folds and longitudinal levees within and at the margins of the units. Finally, two-dimensional power spectra analyses are used to quantify how roughness varies with length scale. These results indicate that no dominant length scale of roughness exists for smooth, unfailed terrain. In contrast, zones with different styles of landslide deformation exhibit distinctive spectral peaks that correspond to the scale of deformation features, such as the compression folds. The topographic-based analyses described here may be used to objectively delineate landslide features, generate mechanical inferences about landslide behavior, and evaluate relatively the recent activity of slides. 相似文献
10.
11.
Terrain Pattern Recognition and Spatial Decision Making for Regional Slope Stability Studies 总被引：1，自引：0，他引：1
A terrain partition scheme is presented that allows the identification of regions with high landslide risk in natural terrain zones on the basis of geomorphometric criteria from moderate resolution DEMs. The key factor being the terrain segmentation to aspect regions (regions formed by points preserving the same aspect direction) instead of using an artificial regular-grid terrain partition scheme. The study area is in western Greece (NW Peloponnesus) whereas a moderate resolution digital elevation model with spacing 75 m is used. Landslide inventory analysis and knowledge conceptualization identified that the landslide susceptibility of a particular aspect region is high, if the mean elevation is low and the mean gradient is high. Each aspect region was parametrically represented on the basis of its mean gradient and elevation. The domain of each parameter was divided to seven slices (classes) on the basis of the observed density. Subsequent knowledge based mapping identified aspect regions with high landslide susceptibility for the following spatial rule: (a) “mean slope in class 6 or 7” and (b) “mean elevation in class 1 to 5”. Alternatively the rule is expressed as mean slope to be equal or greater than 15∘ whereas mean elevation to be in the range 0 to 750 m. These identified zones correspond to regions where historical landslides occurred (populated coastal areas in the North) as well as to south regions (natural terrain zone) where no landslide record is available, because of the limitations posed by the natural terrain landslide mapping program in Greece. The presented terrain segmentation technique combined to the spatial decision-making process, provided both an object framework for integrating geomorphometric parameters and a method for landslide risk analysis in natural terrain zones. 相似文献
12.
基于DEM的地形单元多样性指数及其算法 总被引：4，自引：0，他引：4
在阐述地形信息表达研究进展的基础上,提出基于DEM地形单元多样性指数的概念和算法。地形单元多样性指数综合了高程、坡度、坡位、坡向、汇流量和水域信息等要素。其算法集成地形位置指数和地形湿度指数算法,采用图层叠加分析,设定分类、分级指标,进行重分类组合,划分地形单元类型,利用窗口分析法计算地形单元多样性指数。以四川省为试验区,利用精度为100 m的DEM数据和水域分布数据进行模拟计算,地形单元划分为13种典型类型,统计窗口半径设为900 m,计算出的多样性指数值小于0.5的区域仅占总面积的11%,大于0.75的区域达57%,符合实验区地形特征,并对算法进行了可行性分析和验证。结果表明,该算法提取的地形单元多样性指数可以有效反映地表形态的多样性特征及其变化。该研究结果为进一步探讨基于DEM地表形态信息的概念体系,以及从微观到宏观的地形信息空间分析研究创造了条件。 相似文献
13.
Ana Casado Borbála Hortobágyi Erwan Roussel 《International journal of geographical information science》2018,32(12):2427-2446
The geometry of impounded surfaces is a key tool to reservoir storage management and projection. Yet topographic data and bathymetric surveys of average-aged reservoirs may be absent for many regions worldwide. This paper examines the potential of contour line interpolation (TOPO) and Structure from Motion (SfM) photogrammetry to reconstruct the topography of existing reservoirs prior to dam closure. The study centres on the Paso de las Piedras reservoir, Argentina, and assesses the accuracy and reliability of TOPO- and SfM- derived digital elevation models (DEMs) using different grid resolutions. All DEMs were of acceptable quality. However, different interpolation techniques produced different types of error, which increased (or decreased) with increasing (or decreasing) grid resolution as a function of their nature, and relative to the terrain complexity. In terms of DEM reliability to reproduce area–elevation relationships, processing-related disagreements between DEMs were markedly influenced by topography. Even though they produce intrinsic errors, it is concluded that both TOPO and SfM techniques hold great potential to reconstruct the bathymetry of existing reservoirs. For areas exhibiting similar terrain complexity, the implementation of one or another technique will depend ultimately on the need for preserving accurate elevation (TOPO) or topographic detail (SfM). 相似文献
14.
DEM提取黄土高原地面坡度的不确定性 总被引：72，自引：0，他引：72
选择陕北黄土高原6个典型地貌类型区为试验样区,采用野外实测及高精度的1:1万比例尺DEM为基准数据,研究栅格分辨率及地形粗糙度对DEM所提取地面平均坡度精度的影响。结果显示,对于1:1万比例尺DEM,5 m是保证该地区地形描述精度的理想分辨率尺度;多要素逐步回归模拟的方法进一步揭示了DEM所提取的地面平均坡度误差E与栅格分辨率X以及地形起伏的代表性因子-沟壑密度S之间存在的量化关系为E = (0.0015S2+0.031S-0.0325)X-0.0045S2-0.155S+0.1625,该结果也为确定适用的DEM分辨率提供了理论依据。 相似文献
15.
Qiming Zhou Xuejun Liu Yizhong Sun 《International journal of geographical information science》2013,27(10):1137-1147
The objective of this research is to study the relationship between terrain complexity and terrain analysis results from grid‐based digital elevation models (DEMs). The impact of terrain complexity represented by terrain steepness and orientation on derived parameters such as slope and aspect has been analysed. Experiments have been conducted to quantify the uncertainties created by digital terrain analysis algorithms. The test results show that (a) the RMSE of derived slope and aspect is negatively correlated with slope steepness; (b) the RMSE of derived aspect is more sensitive to terrain complexity than that of derived slope; and (c) the uncertainties in derived slope and aspect tend to be found in flatter areas, and decrease with increasing terrain complexity. The study shows that although primary surface parameters can be well defined mathematically, the implementation of those mathematical models in a GIS environment may generate considerable uncertainties related to terrain complexity. In general, when terrain is rugged with steep slopes, the uncertainty of derived parameters is quite minimal. While in flatter areas, the DEM‐based derivatives, particularly the aspect, may contain a great amount of uncertainty, causing significant limitation in applying the analytical results. 相似文献
16.
Jane Xinxin Zhang Kang‐Tsung Chang Joan Qiong Wu 《International journal of geographical information science》2013,27(8):925-942
Digital elevation models (DEMs) vary in resolution and accuracy by the production method. DEMs with different resolutions and accuracies can generate varied topographic and hydrological features, which can in turn affect predictions by soil erosion models, such as the WEPP (Water Erosion Prediction Project) model. This study investigates the effects of DEMs on deriving topographic and hydrological attributes, and on predicting watershed erosion using WEPP v2006.5. Six DEMs at three resolutions from three sources were prepared for two small forested watersheds located in northern Idaho, USA. These DEMs were used to calculate topographic and hydrological parameters that served as inputs to WEPP. The model results of sediment yields and runoffs were compared with field observations. For both watersheds, DEMs with different resolutions and sources generated varied watershed shapes and structures, which in turn led to different extracted hill slope and channel lengths and gradients, and produced substantially different erosion predictions by WEPP. 相似文献
17.
T. Edwin Chow Michael E. Hodgson 《International journal of geographical information science》2013,27(10):1277-1295
This paper examines the effect of scale (exhibited by spatial sampling) in modeling mean slope from lidar data using two representations of scale: lidar posting density (i.e. post‐spacing) and DEM resolution (i.e. cell size). The study areas selected include six small (i.e. approximately 3 km2) urban drainage basins in Richland County, SC, USA, which share similar hydrologic characteristics. This research spatially sampled an airborne lidar dataset collected in 2000 at a 2 m nominal posting density to simulate lidar posting density at various post‐spacings, from 2 m through 10 m. DEMs were created from the lidar observations at a corresponding cell size using spatial interpolation. Finally, using these DEMs, a sensitivity analysis between modeled terrain slope and lidar post‐spacing was conducted. Results of the sensitivity analyses showed that the deviation between mean slope and modeled mean slope decreases with finer posting density and DEM resolution. The relationship of mean slope with varying cell sizes and post‐spacing suggests a linear and a logarithmic function, respectively, for all study areas. More importantly, cell size has a greater effect on mean slope than lidar posting density. Implications of these results for lumped hydrologic modeling are then postulated. 相似文献
18.
JAY GAO 《International journal of geographical information science》2013,27(2):199-212
This paper examines the impact of DEM resolution on the accuracy of terrain representation and of the gradient determined. The DEMs of three terrain types with diverse complexities were constructed from digitizing contours and then kriging. The accuracy (RMSE) of the DEMs was regressed against contour density (D) and DEM resolution (S) at six resolution levels. It is found that RMSE may be expressed as (7.274 1.666S)D/1000 with an R value of 0.9659. The representation accuracy decreases moderately at an intermediate resolution, but sharply at coarse resolutions for all three terrain types. Resolution reduction profoundly affects the gradient determined from the DEM. While exerting little influence on mean gradient, resolution significantly affects the standard deviation of gradient, especially for a simple terrain. The results obtained in this study may be used to determine the DEM resolution that is appropriate to the accuracy requirements of a particular user. 相似文献
19.
基于DEM的山地总辐射模型及实现 总被引：15，自引：0，他引：15
总辐射状况是决定山地气候的主导性因子。山区地形条件复杂,总辐射分布差异显著,为了便于研究山区总辐射的地域分布规律,该文建立了一种基于DEM模拟山区总辐射的方法,通过提取数字坡度模型、数字高度模型以及地形遮蔽度模型等信息,并采用多层面复合分析的方法,建立了山区直接辐射、散射辐射以及总辐射的数字模型。实验证明,太阳总辐射及其分量在山区中有很强的地域分布规律。该方法采用的DEM精度高,能够精细地反映太阳辐射的地区分布差异,为山地气候资源调查与利用、生态环境建设乃至精细农业的实施提供重要依据。 相似文献
20.
Drainage density, slope angle, and relative basin position in Japanese bare lands from high-resolution DEMs 总被引：2，自引：0，他引：2
Relationships between drainage density and slope angle for three bare lands in Japan were analyzed with special attention to channels at early erosion stages and channels in a badland-type terrain. Two of the bare lands were caused by volcanic eruptions 1 or 30–40 years ago, and the other one is a landslide scar formed more than 100 years ago. Raster digital elevation models (DEMs) with a 1-m resolution and ortho aerial photos were generated using digital photogrammetry to enable detailed stream-net extraction and topographic analyses. Data for drainage density, slope angle, and relative height for 88 subwatersheds were obtained from the DEMs and derived stream-nets. The relationship between drainage density and slope angle for each subwatershed can be divided into two types: downward sloping and convex upward. Although previous studies suggested that drainage density positively correlates with slope angle if overland flow is dominant, this correlation seldom occurs in the study areas. The two types of drainage density–slope angle relationships correspond to differing channelization stages that reflect the extension and integration of existing channels, as well as the formation of new low-order streams in response to base-level lowering. The location of subwatersheds within each study area seems to play a major role in determining the stages of channel development and, in turn, the types of drainage density–slope angle relationships. 相似文献