首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 671 毫秒
1.
It has been observed that the field biodegradation rates for soluble hydrocarbon plumes are significantly smaller than the aerobic rates observed in the laboratory. It is believed that this difference is related to the fact that in the field oxygen and hydrocarbon must be mixed before the biodegradation reaction can occur, and that the effective degradation rate is controlled by the actual, not mean, concentrations of oxygen and hydrocarbon. In this work, we present a conceptual model of oxygen-mixing limited biodegradation, which indicates that the effective degradation rate should depend on the cross correlation between the oxygen and hydrocarbon concentration fluctuations. This is followed by a development of a rigorous, field-scale model.  相似文献   

2.
Petroleum hydrocarbon vapors biodegrade aerobically in the subsurface. Depth profiles of petroleum hydrocarbon vapor and oxygen concentrations from seven locations in sandy and clay soils across four states of Australia are summarized. The data are evaluated to support a simple model of biodegradation that can be used to assess hydrocarbon vapors migrating toward built environments. Multilevel samplers and probes that allow near‐continuous monitoring of oxygen and total volatile organic compounds (VOCs) were used to determine concentration depth profiles and changes over time. Collation of all data across all sites showed distinct separation of oxygen from hydrocarbon vapors, and that most oxygen and hydrocarbon concentration profiles were linear or near linear with depth. The low detection limit on the oxygen probe data and because it is an in situ measurement strengthened the case that little or no overlapping of oxygen and hydrocarbon vapor concentration profiles occurred, and that indeed oxygen and hydrocarbon vapors were largely only coincident near the location where they both decreased to zero. First‐order biodegradation rates determined from all depth profiles were generally lower than other published rates. With lower biodegradation rates, the overlapping of depth profiles might be expected, and yet such overlapping was not observed. A model of rapid (instantaneous) reaction of oxygen and hydrocarbon vapors compared to diffusive transport processes is shown to explain the important aspects of the 13 depth profiles. The model is simply based on the ratio of diffusion coefficients of oxygen and hydrocarbon vapors, the ratio of the maximum concentrations of oxygen and hydrocarbon vapors, the depth to the maximum hydrocarbon source concentration, and the stoichiometry coefficient. Whilst simple, the model offers the potential to incorporate aerobic biodegradation into an oxygen‐limited flux‐reduction approach for vapor intrusion assessments of petroleum hydrocarbon compounds.  相似文献   

3.
A vertical soil column setup integrated with wetlands is developed to study the biodegradation and transport of toluene, a light non‐aqueous phase liquid (LNAPL), in the subsurface environment. LNAPL‐contaminated water is applied to infiltrate from the top of the soil column. The observed and simulated breakthrough curves show high equilibrium concentration at top ports rather than at lower ports, indicating effective toluene biodegradation with soil depth. The observed equilibrium concentration of toluene is higher in the case of unplanted wetland, asserting an accelerated biodegradation rate in the planted case. A difference in the relative concentration of toluene between input and output fluxes at 100 h is found as 13.34% and 30.86% for planted and unplanted wetland setups, respectively. Estimated biodegradation rates show that toluene degradation is 2.5 times faster in the planted wetland setup. In addition, the difference in the observed bacterial count and dissolved oxygen prove that toluene degraded aerobically at a faster rate in the planted setup. Simulations show that as time reached 80–100 h, there is no significant change in concentration profile, thereby confirming the equilibrium condition. The results of this study will be useful to frame plant‐assisted bioremediation techniques for LNAPL‐contaminated soil–water resources in the field.  相似文献   

4.
Respiration tests were carried out during a seven month bioremediation field trial to monitor biodegradation rates of weathered diesel non-aqueous phase liquid (NAPL) contaminating a shallow sand aquifer. Multiple depth monitoring of oxygen concentrations and air-filled porosity were carried out in nutrient amended and nonamended locations to assess the variability of degradation rate estimates calculated from respiration tests.
The field trial consisted of periodic addition of nutrients (nitrogen and phosphorus) and aeration of a 100 m2 trial plot. During the bioremediation trial, aeration was stopped periodically, and decreases in gaseous oxygen concentrations were logged semi-continuously using data loggers attached to recently developed in situ oxygen probes placed at multiple depths above and within a thin NAPL-contaminated zone. Oxygen usage rate coefficients were determined by fitting zero-and first-order rate equations to the oxygen concentration reduction curves, although only zero-order rates were used to calculate biodegradation rates. Air-filled porosity estimates were found to vary by up to a factor of two between sites and at different times.
NAPL degradation rates calculated from measured air-filled porosity and oxygen usage rate coefficients ranged up to 69 mg kg-1 day-1. These rates are comparable to and higher than rates quoted in other studies, despite the high concentrations and weathered state of the NAPL at this test site. For nutrient-amended sites within the trial plot, estimates of NAPL degradation rates were two to three times higher than estimates from nonamended sites. Rates also increased with depth.  相似文献   

5.
A detailed seasonal study of soil vapor intrusion at a cold climate site with average yearly temperature of 1.9 °C was conducted at a house with a crawlspace that overlay a shallow dissolved‐phase petroleum hydrocarbon (gasoline) plume in North Battleford, Saskatchewan, Canada. This research was conducted primarily to assess if winter conditions, including snow/frost cover, and cold soil temperatures, influence aerobic biodegradation of petroleum vapors in soil and the potential for vapor intrusion. Continuous time‐series data for oxygen, pressure differentials, soil temperature, soil moisture, and weather conditions were collected from a high‐resolution monitoring network. Seasonal monitoring of groundwater, soil vapor, crawlspace air, and indoor air was also undertaken. Petroleum hydrocarbon vapor attenuation and biodegradation rates were not significantly reduced during low temperature winter months and there was no evidence for a significant capping effect of snow or frost cover that would limit oxygen ingress from the atmosphere. In the residual light nonaqueous phase liquid (LNAPL) source area adjacent to the house, evidence for biodegradation included rapid attenuation of hydrocarbon vapor concentrations over a vertical interval of approximately 0.9 m, and a corresponding decrease in oxygen to less than 1.5% v/v. In comparison, hydrocarbon vapor concentrations above the dissolved plume and below the house were much lower and decreased sharply within a few tens of centimeters above the groundwater source. Corresponding oxygen concentrations in soil gas were at least 10% v/v. A reactive transport model (MIN3P‐DUSTY) was initially calibrated to data from vertical profiles at the site to obtain biodegradation rates, and then used to simulate the observed soil vapor distribution. The calibrated model indicated that soil vapor transport was dominated by diffusion and aerobic biodegradation, and that crawlspace pressures and soil gas advection had little influence on soil vapor concentrations.  相似文献   

6.
This study evaluates the theory, and some practical aspects of using temperature measurements to assess aerobic biodegradation in hydrocarbon contaminated soil. The method provides an easily applicable alternative for quantifying the rate of biodegradation and/or evaluating the performance of in situ remediation systems. The method involves two nonintrusive procedures for measuring vertical temperature profiles down existing monitoring wells; one using a thermistor on a cable for one‐time measurements and the other using compact temperature data loggers deployed for 3‐month to 1‐year period. These vertical temperature profile measurements are used to identify the depth and lateral extent of biodegradation as well as to monitor seasonal temperature changes throughout the year. The basic theory for using temperature measurements to estimate the minimum rate of biodegradation will be developed, and used to evaluate field measurements from sites in California where biodegradation of spilled petroleum hydrocarbons is due to natural processes. Following, temperature data will be used to evaluate the relative rates of biodegradation due to natural processes and soil vapor extraction (SVE) at a former refinery site in the North‐Central United States. The results from this study show that the temperature method can be a simple, cost effective tool for assessing biodegradation in the soil, and optimizing remediation systems at a wide variety of hydrocarbon spill sites.  相似文献   

7.
Aerobic biodegradation of vapor-phase petroleum hydrocarbons was evaluated in an intact soil core from the site of an aviation gasoline release. An unsaturated zone soil core was subjected to a flow of nitrogen gas, oxygen, water vapor, and vapor-phase hydrocarbons in a configuration analogous to a biofilter or an in situ bioventing or sparging situation. The vertical profiles of vapor-phase hydrocarbon concentration in the soil core were determined by gas chromatography of vapor samples. Biodegradation reduced low influent hydrocarbon concentrations by 45 to 92 percent over a 0.6-m interval of an intact soil core. The estimated total hydrocarbon concentration was reduced by 75 percent from 26 to 7 parts per million. Steady-state concentrations were input to a simple analytical model balancing advection and first-order biodegradation of hydrocarbons. First-order rate constants for the major hydrocarbon compounds were used to calibrate the model to the concentration profiles. Rate constants for the seven individual hydrocarbon compounds varied by a factor of 4. Compounds with lower molecular weights, fewer methyl groups, and no quaternary carbons tended to have higher rate constants. The first-order rate constants were consistent with kinetic parameters determined from both microcosm and tubing cluster studies at the field site.  相似文献   

8.
The temperature sensitivity of microbial populations is reflected in measured source attenuation rates at hydrocarbon‐impacted sites. The objective of this study was to evaluate the correlation between temperature and source attenuation rates (concentration vs. time attenuation rate over many years) of benzene and toluene by analyzing groundwater monitoring data from >2000 hydrocarbon sites. Historical monitoring records were obtained from three databases, processed to yield long‐term multiyear source attenuation rates, and then compared with representative temperatures at each site. Statistically significant and positive relationships between temperature and source attenuation rates were established for benzene and toluene, indicating that temperature does impact hydrocarbon degradation, but is one of many factors that contribute to source attenuation. There was an observed 1.1 to 1.6 times increase in attenuation rates per 10 °C increase in temperature, which is less than the rate increases predicted by the Arrhenius equation. The temperature dependence on attenuation rate is consistent with several lines of evidence that methanogenesis plays a key role in the rate of hydrocarbon source zone attenuation rather than being controlled strictly by the availability of electron acceptors. First, methanogenesis is known to be strongly influenced by temperature, with significantly higher rates up to about 35 °C. Second, the temperature‐degradation rate relationship was stronger at sites with deeper water tables (>30 ft) that are less susceptible to oxygen influx than sites with shallow water tables (<15 ft). Third, dissolved methane concentrations were higher at sites with warmer temperatures. Overall, these results provide indirect support for a conceptual model where methanogenesis is a key degradation process at hydrocarbon sites, and that attenuation of these source zones is temperature‐sensitive.  相似文献   

9.
Geochemical Indicators of Intrinsic Bioremediation   总被引：19，自引：0，他引：19  
A detailed field investigation has been completed at a gasoline-contaminated aquifer near Rocky Point, NC, to examine possible indicators of intrinsic bioremediation and identify factors that may significantly influence the rate and extent of bioremediation. The dissolved plume of benzene, toluene, ethylbenzene, and xylene (BTEX) in ground water is naturally degrading. Toluene and o-xylene are most rapidly degraded followed by m-, p-xylene, and benzene. Ethylbenzene appears to degrade very slowly under anaerobic conditions present in the center of the plume. The rate and extent of biodegradation appears to be strongly influenced by the type and quantity of electron acceptors present in the aquifer. At the upgradient edge of the plume, nitrate, ferric iron, and oxygen are used as terminal electron acceptors during hydrocarbon biodegradation. The equivalent of 40 to 50 mg/I of hydrocarbon is degraded based on the increase in dissolved CO2 relative to background ground water. Immediately downgradient of the source area, sulfate and iron are the dominant electron acceptors. Toluene and o-xylene are rapidly removed in this region. Once the available oxygen, nitrate, and sulfate are consumed, biodegradation is limited and appears to be controlled by mixing and aerobic biodegradation at the plume fringes.  相似文献   

10.
The fate of hydrocarbons in the subsurface near Bemidji, Minnesota, has been investigated by a multidisciplinary group of scientists for over a quarter century. Research at Bemidji has involved extensive investigations of multiphase flow and transport, volatilization, dissolution, geochemical interactions, microbial populations, and biodegradation with the goal of providing an improved understanding of the natural processes limiting the extent of hydrocarbon contamination. A considerable volume of oil remains in the subsurface today despite 30 years of natural attenuation and 5 years of pump‐and‐skim remediation. Studies at Bemidji were among the first to document the importance of anaerobic biodegradation processes for hydrocarbon removal and remediation by natural attenuation. Spatial variability of hydraulic properties was observed to influence subsurface oil and water flow, vapor diffusion, and the progression of biodegradation. Pore‐scale capillary pressure‐saturation hysteresis and the presence of fine‐grained sediments impeded oil flow, causing entrapment and relatively large residual oil saturations. Hydrocarbon attenuation and plume extent was a function of groundwater flow, compound‐specific volatilization, dissolution and biodegradation rates, and availability of electron acceptors. Simulation of hydrocarbon fate and transport affirmed concepts developed from field observations, and provided estimates of field‐scale reaction rates and hydrocarbon mass balance. Long‐term field studies at Bemidji have illustrated that the fate of hydrocarbons evolves with time, and a snap‐shot study of a hydrocarbon plume may not provide information that is of relevance to the long‐term behavior of the plume during natural attenuation.  相似文献   

11.
The occurrence of aerobic biodegradation in the vadose zone between a subsurface source and a building foundation can all-but eliminate the risks from methane and petroleum vapor intrusion (PVI). Understanding oxygen availability and the factors that affect it (e.g., building sizes and their distribution) are therefore critical. Uncovered ground surfaces allow oxygen access to the subsurface to actively biodegrade hydrocarbons (inclusive of methane). Buildings can reduce the net flux of oxygen into the subsurface and so reduce degradation rates. Here we determine when PVI and methane risk is negligible and/or extinguished; defined by when oxygen is present across the entire sub-slab region of existing or planned slab-on-ground buildings. We consider all building slab sizes, all depths to vapor sources and the effect of spacings between buildings on the availability of oxygen in the subsurface. The latter becomes critical where buildings are in close proximity or when increased building density is planned. Conservative assumptions enable simple, rapid and confident screening should sites and building designs comply to model assumptions. We do not model the aboveground “building” processes (e.g., air exchange), and assume the slab-on-ground seals the ground surface so that biodegradation of hydrocarbons is minimized under the built structure (i.e., the assessment remains conservative). Two graphs represent the entirety of the outcomes that allow simple screening of hydrocarbon vapors based only on the depth to the source of vapors below ground, the concentration of vapors within the source, the width of the slab-on-ground building, and the gap between buildings; all independent of soil type. Rectangular, square, and circular buildings are considered. Comparison with field sites and example applications are provided, along with a simple 8-step screening guide set in the context of existing guidance on PVI assessment.  相似文献   

12.
Xu R  Yong LC  Lim YG  Obbard JP 《Marine pollution bulletin》2005,51(8-12):1101-1110
Nutrient concentration and hydrocarbon bioavailability are key factors affecting biodegradation rates of oil in contaminated beach sediments. The effect of a slow-release fertilizer, Osmocote, as well as two biopolymers, chitin and chitosan, on the bioremediation of oil-spiked beach sediments was investigated using an open irrigation system over a 56-day period under laboratory conditions. Osmocote was effective in sustaining a high level of nutrients in leached sediments, as well as elevated levels of microbial activity and rates of hydrocarbon biodegradation. Chitin was more biodegradable than chitosan and gradually released nitrogen into the sediment. The addition of chitin or chitosan to the Osmocote amended sediments enhanced biodegradation rates of the alkanes relative to the presence of Osmocote alone, where chitosan was more effective than chitin due to its greater oil sorption capacity. Furthermore, chitosan significantly enhanced the biodegradation rates of all target polycyclic aromatic hydrocarbons.  相似文献   

13.
Enhanced subsurface biorestoration is rapidly becoming recognized as a valuable tool for the restoration of hydrocarbon-contaminated aquifers and sediments. Previous field and laboratory studies at a former wood creosoting facility near Conroe, Texas, have indicated that insufficient oxygen is the primary factor limiting the biotransformation of polynuclear aromatics (PNAs) in sediments and ground water at this site. A series of laboratory experiments and field push-pull injection tests were performed as part of this project to: (1) study the effect of low oxygen concentrations on the biotransformation of PNAs; (2) identify the minimum concentration of PNAs that could be achieved through the addition of oxygen alone; (3) confirm that enhanced subsurface biorestoration is feasible at this site; and (4) test an existing numerical model of the biotransformation process (BIOPLUME). The laboratory studies demonstrated that biotransformation of the PNAs was not inhibited at dissolved oxygen concentrations as low as 0.7 mg/L although this work did suggest that there may be a minimum PNA concentration of 30 to 70 μg/L total PNAs below which biotransformation was inhibited. The field push-pull tests confirmed that addition of oxygen was effective in enhancing the subsurface biodegradation of the PNAs. The minimum concentration achieved using oxygen alone was approximately 60 μg/L total PNAs. Minimal biotransformation of these compounds was observed without oxygen addition. The numerical model BIOPLUME was tested against monitoring data from the field experiments and appears to provide a good approximation of the biodegradation process.  相似文献   

14.
Transport and Biological Fate of Toluene in Low-Permeability Soils   总被引：1，自引：0，他引：1  
The effect of simultaneous sorption, diffusion, and biodegradation on the fate and transport of toluene in low-permeability soil formations was examined. A transport model accounting for vapor and liquid sorption, vapor diffusions, and first-order biodegradation was developed to describe the movement of volatile solute in unsaturated soils. Modeling studies were followed with laboratory batch and column studies on fine-grained soil samples obtained from a gasoline-contaminated site. Batch experiments yielded the sorption and diffusion coefficients for generating theoretical solute transport profiles. Column studies were conducted to examine toluene sorption, diffusion, and biodegradation under aerobic and denitrifying conditions. Results from the column studies indicated that vapor sorption onto the soil was minimal due to the high moisture content of the soil. Comparison of model predictions with experimental results indicated that the SASK model, which is based on the resistivity theory, provided a more accurate prediction of the vapor phase tortuosity than the frequently used Millington-Quirk equation. Laboratory results of toluene concentration profiles matched well with the model predictions and yielded degradation rates comparable to those obtained in the field. Column studies, examining toluene biodegradation under aerobic and denitrifying conditions in low-permeability soils, indicated that the presence of excess nitrate in aerobic environments yielded higher solute degradation rates than those observed under exclusively aerobic systems.  相似文献   

15.
Modeling oil biodegradation is an important step in predicting the long term fate of oil on beaches. Unfortunately, existing models do not account mechanistically for environmental factors, such as pore water nutrient concentration, affecting oil biodegradation, rather in an empirical way. We present herein a numerical model, BIOB, to simulate the biodegradation of insoluble attached hydrocarbon. The model was used to simulate an experimental oil spill on a sand beach. The biodegradation kinetic parameters were estimated by fitting the model to the experimental data of alkanes and aromatics. It was found that parameter values are comparable to their counterparts for the biodegradation of dissolved organic matter. The biodegradation of aromatics was highly affected by the decay of aromatic biomass, probably due to its low growth rate. Numerical simulations revealed that the biodegradation rate increases by 3–4 folds when the nutrient concentration is increased from 0.2 to 2.0 mg N/L.  相似文献   

16.
Oxygen probes developed to measure in situ oxygen concentrations in gaseous and aqueous environments were evaluated in laboratory tests and during long-term field evaluation trials at contaminated sites. The oxygen probes were shown to have a linear calibration and to be accurate compared to conventional dissolved oxygen electrodes and gas chromatography, both of which require labor-intensive sample collection and processing. The probes, once calibrated, required no maintenance or recalibration for up to a period of 7 years in low-oxygen environments, demonstrating long-term stability. Times to achieve 90% of the stabilized concentration ( t 90) after a step change in aqueous oxygen concentration were 100–120 min in laboratory experiments and up to 180 min in field experiments, which is adequate for monitoring subsurface changes. Field application data demonstrated that the oxygen probes could monitor oxygen concentrations in hydrocarbon-contaminated ground water to a depth of 20 m below the water table or in pyritic vadose zones over extended periods. During bioremediation field trials, oxygen monitoring enabled estimation of oxygen utilization rates by microorganisms and hydrocarbon biodegradation rates. Also, probes were able to monitor the development of ground water desaturation during air sparging trials, enabling the automated assessment of the distribution of injected air.  相似文献   

17.
Natural Attenuation of Aromatic Hydrocarbons in a Shallow Sand Aquifer   总被引：8，自引：0，他引：8  
Inadvertent release of petroleum products such as gasoline into the subsurface can initiate ground water contamination, particularly by the toxic, water-soluble and mobile gasoline components: benzene, toluene and xylenes (BTX). This study was undertaken to examine the processes controlling the rate of movement and the persistence of dissolved BTX in ground water in a shallow, unconfined sand aquifer.
Water containing about 7.6 mg/ L total BTX was introduced below the water table and the migration of contaminants through a sandy aquifer was monitored using a dense sampling network. BTX components migrated slightly slower than the ground water due to sorptive retardation. Essentially all the injected mass of BTX was lost within 434 days due to biodegradation. Rates of mass loss were similar for all monoaromatics; benzene was the only component to persist beyond 270 days. Laboratory biodegradation experiments produced similar rates, even when the initial BTX concentration varied.
A dominant control over BTX biodegradation was the availability of dissolved oxygen. BTX persisted at the field site in layers low in dissolved oxygen. Decreasing mass loss rates over time observed in the field experiment are not likely due to first-order deeradation rates, but rather to the persistence of small fractions of BTX mass in anoxic layers.  相似文献   

18.
The effects of adding oxygen to anaerobic aquifer materials on biodegradation of phenoxy acid herbicides were studied by laboratory experiments with aquifer material from two contaminated sites (a former agricultural machinery service and an old landfill). At both sites, the primary pollutants were phenoxy acids and related chlorophenols. It was found that addition of oxygen enhanced degradation of the six original phenoxy acids and six original chlorophenols. Inverse modeling on 14C 4-chloro-2-methylphenoxypropanoic acid (MCPP) degradation curves revealed that increasing the oxygen concentrations from <0.3 mg/L up to 7 to 8 mg/L shortened the lag phases (from approximately 150 d to 5 to 25 d) and increased first-order degradation rate constants by 1 order of magnitude (from approximately 5 x 10(-2) d(-1) to up to 30 x 10(-2) d(-1)). Additionally, the degree of MCPP mineralization was increased (30% to 50% mineralized at low oxygen concentrations and 50% to 70% mineralized at high oxygen concentrations, based on 14CO2 recovery). These positive effects on degradation were observed even at relatively low oxygen concentrations (2 mg/L). Furthermore, effects related to the addition of oxygen on the general geochemistry were studied. An oxygen consumption of 2.2 to 2.6 mg O2/g dw was observed due to oxidation of solid organic matter and, to some extent (0.5% to 11% of the total oxygen consumption), water-soluble compounds such as Fe2+, dissolved Mn, nonvolatile organic carbon, and NH4+. Overall, the results suggest that stimulated biodegradation by addition of oxygen might be a feasible remediation technology at herbicide-contaminated sites, although oxygen consumption by the sediment could limit the applicability.  相似文献   

19.
Natural source zone depletion (NSZD) refers to processes within chemically impacted vadose and saturated zones that reduce the mass of contaminants remaining in a defined source control volume. Studies of large petroleum hydrocarbon release sites have shown that the depletion rate by vapor phase migration of degradation products from the source control volume through the vadose zone (V‐NSZD) is often considerably higher than the rate of depletion from the source control volume by groundwater flow carrying dissolved petroleum hydrocarbons arising from dissolution, desorption, or back diffusion, and degradation products arising from biodegradation (GW‐NSZD). In this study, we quantified vadose zone and GW‐NSZD at a small unpaved fuel release site in California typical of those in settings with predominantly low permeability media. We estimated vadose zone using a dense network of efflux monitoring locations at four sampling events over 2 years, and GW‐NSZD using groundwater monitoring data downgradient of the source control volume in three depth intervals spanning up to 9 years. On average, vadose zone was 17 times greater than GW‐NSZD during the time interval of comparison, and vadose zone was in the range of rates quantified at other sites with petroleum hydrocarbon releases. Estimating vadose zone and GW‐NSZD rates is challenging but the vadose zone rate is the best indicator of overall source mass depletion, whereas GW‐NSZD rates may be useful as baselines to quantify progress of natural or engineered remediation in portions of the saturated zone in which there are impediments to loss of methane and other gases to the vadose zone.  相似文献   

20.
We compare two methods for estimating the natural source zone depletion (NSZD) rate at fuel release sites that occurs by groundwater flow through the source zone due to dissolution and transport of biodegradation products. Dissolution is addressed identically in both methods. The “mass budget method”, previously proposed and applied by others, estimates the petroleum hydrocarbon biodegradation rate based on dissolved electron acceptor delivery and dissolved biodegradation product removal by groundwater flow. The mass budget method relies on assumed stoichiometry for the degradation reactions and differences in concentrations of dissolved species (oxygen, nitrate, sulfate, reduced iron, reduced manganese, nonvolatile dissolved organic carbon, methane) at monitoring locations upgradient and downgradient of the source zone. We illustrate a refinement to account for degradation reactions associated with loss of reduced iron from solution. The “carbon budget method,” a simplification of approaches applied by others, addresses carbon‐containing species in solution or lost from solution (precipitated) and does not require assumptions about stoichiometry or information about electron acceptors. We apply both methods to a fuel release site with unusually detailed monitoring data and discuss applicability to more typical and less thoroughly monitored sites. The methods, as would typically be applied, yield similar results but have different constraints and uncertainties. Overall, we conclude that the carbon budget method has greater practical utility as it is simpler, requires fewer assumptions, accounts for most iron‐reducing reactions, and does not include CO2 that escapes from the saturated to the unsaturated zone.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号