首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 125 毫秒
1.
Anisotropy and heterogeneity of hydraulic conductivity (K) are suspected of greatly affecting rates and patterns of ground‐water seepage in peats. A new laboratory method, termed here the modified cube method, was used to measure horizontal and vertical hydraulic conductivity (Kh and Kv) of 400 samples of bog peat. The new method avoids many of the problems associated with existing field and laboratory methods, and is shown to give relatively precise measurements of K. In the majority of samples tested, Kh was much greater than Kv, indicating that the bog peat was strongly anisotropic. Log10Kh, log10Kv, and log10 (Kh/Kv) were found to vary significantly with depth, although none of the relationships was simple. We comment on the scale dependency of our measurements. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

2.
Peat soils are heterogeneous, anisotropic porous media. Compared to mineral soils, there is still limited understanding of physical and solute transport properties of fen peat soils. In this study, we aimed to explore the effect of soil anisotropy on solute transport in degraded fen peat. Undisturbed soil cores, taken in vertical and horizontal direction, were collected from one drained and one restored fen peatland both in a comparable state of soil degradation. Saturated hydraulic conductivity (K s) and chemical properties of peat were determined for all soil cores. Miscible displacement experiments were conducted under saturated steady state conditions using potassium bromide as a conservative tracer. The results showed that (1) the K s in vertical direction (K sv) was significantly higher than that in horizontal direction (Ksh), indicating that K s of degraded fen peat behaves anisotropically; (2) pronounced preferential flow occurred in vertical direction with a higher immobile water fraction and a higher pore water velocity; (3) the 5% arrival time (a proxy for the strength of preferential flow) was affected by soil anisotropy as well as study site. A strong correlation was found between 5% arrival time and dispersivity, K s and mobile water fraction; (4) phosphate release was observed from drained peat only. The impact of soil heterogeneity on phosphate leaching was more pronounced than soil anisotropy. The soil core with the strongest preferential flow released the highest amount of phosphate. We conclude that soil anisotropy is crucial in peatland hydrology but additional research is required to fully understand anisotropy effects on solute transport.  相似文献   

3.
The parallel physically-based surface–subsurface model PARFLOW was used to investigate the spatial patterns and temporal dynamics of river–aquifer exchange in a heterogeneous alluvial river–aquifer system with deep water table. Aquifer heterogeneity at two scales was incorporated into the model. The architecture of the alluvial hydrofacies was represented based on conditioned geostatistical indicator simulations. Subscale variability of hydraulic conductivities (K) within hydrofacies bodies was created with a parallel Gaussian simulation. The effects of subscale heterogeneity were investigated in a Monte Carlo framework. Dynamics and patterns of river–aquifer exchange were simulated for a 30-day flow event. Simulation results show the rapid formation of saturated connections between the river channel and the deep water table at preferential flow zones that are characterized by high conductivity hydrofacies. Where the river intersects low conductivity hydrofacies shallow perched saturated zones immediately below the river form, but seepage to the deep water table remains unsaturated and seepage rates are low. Preferential flow zones, although only taking up around 50% of the river channel, account for more than 98% of total seepage. Groundwater recharge is most efficiently realized through these zones. Subscale variability of Ksat slightly increased seepage volumes, but did not change the general seepage patterns (preferential flow zones versus perched zones). Overall it is concluded that typical alluvial heterogeneity (hydrofacies architecture) is an important control of river–aquifer exchange in rivers overlying deep water tables. Simulated patterns and dynamics are in line with field observations and results from previous modeling studies using simpler models. Alluvial heterogeneity results in distinct patterns and dynamics of river–aquifer exchange with implications for groundwater recharge and the management of riparian zones (e.g. river channel-floodplain connectivity via saturated zones).  相似文献   

4.
This study used a two‐dimensional steady‐state finite‐element groundwater flow model to simulate groundwater flow in two Newfoundland blanket peat complexes and to examine flow system sensitivity to changes in water table recharge and aquifer properties. The modelling results were examined within the context of peat‐forming processes in the two complexes. Modelled flow compared favourably with observed flow. The sensitivity analyses suggested that more highly decomposed bog peat along bog margins probably has/had a positive impact on net peat accumulation within bog interiors. Peat with lower hydraulic conductivity along bog margins effectively impedes lateral drainage, localizes water table drawdown to extreme bog margins, and elevates water tables along bog interiors. Peat formation and elevated water tables in adjacent poor fens/laggs currently rely on placic and ortstein horizons impeding vertical drainage and water flow inputs from adjacent bogs. Modest reductions in atmospheric recharge were found to govern bog‐flow‐system geometries in a way that would adversely affect paludification processes in adjacent fens/laggs. Copyright © 2004 John Wiley & Sons, Ltd.  相似文献   

5.
The hyporheic zone (HZ), which is the region beneath or alongside a streambed, plays an important role in the stream's ecology. The duration that a water molecule or a solute remains within the HZ, or residence time (RT), is one of the most common metrics used to evaluate the function of the HZ. The RT is greatly influenced by the streambed's hydraulic conductivity (K), which is intrinsically difficult to characterize due to its heterogeneity and anisotropy. Many laboratory and numerical studies of the HZ have simplified the streambed K to a constant, thus producing RT values that may differ from those gathered from the field. Some studies have considered the heterogeneity of the HZ, but very few have accounted for anisotropy or the natural K distributions typically found in real streambeds. This study developed numerical models in MODFLOW to examine the influence of heterogeneity and anisotropy, and that of the natural K distribution in a streambed, on the RT of the HZ. Heterogeneity and anisotropy were both found to shorten the mean and median RTs while increasing the range of the RTs. Moreover, heterogeneous K fields arranged in a more orderly pattern had longer RTs than those with random K distributions. These results could facilitate the design of streambed K values and distributions to achieve the desired RT during river restoration. They could also assist the translation of results from the more commonly considered homogeneous and/or isotropic conditions into heterogeneous and anisotropic field situations.  相似文献   

6.
Various subsurface flow systems exhibit a combination of small‐scale to large‐scale anisotropy in hydraulic conductivity (K). The large‐scale anisotropy results from systematic trends (e.g., exponential decrease or increase) of K with depth. We present a general two‐dimensional solution for calculation of topography‐driven groundwater flow considering both small‐ and large‐scale anisotropy in K. This solution can be applied to diverse systems with arbitrary head distribution and geometry of the water table boundary, such as basin or hyporheic flow. In a special case, this solution reduces to the well‐known Tóth model of uniform isotropic basin. We introduce an integral measure of flushing intensity that quantifies flushing at different depths. Using this solution, we simulate heads and streamlines and provide analyses of flow structure in the flow domain, relevant to basin analyses or hyporheic flow. It is shown that interactions between small‐scale anisotropy and large‐scale anisotropy strongly control the flow structure. In the classic Tóth flow model, the flushing intensity curves exhibit quasi‐exponential decrease with depth. The new measure is capable of capturing subtle changes in the flow structure. Our study shows that both small‐ and large‐scale anisotropy characteristics have substantial effects that need to be integrated into analysis of topography‐driven flow.  相似文献   

7.
We designed and evaluated a “tube seepage meter” for point measurements of vertical seepage rates (q), collecting groundwater samples, and estimating vertical hydraulic conductivity (K) in streambeds. Laboratory testing in artificial streambeds show that seepage rates from the tube seepage meter agreed well with expected values. Results of field testing of the tube seepage meter in a sandy‐bottom stream with a mean seepage rate of about 0.5 m/day agreed well with Darcian estimates (vertical hydraulic conductivity times head gradient) when averaged over multiple measurements. The uncertainties in q and K were evaluated with a Monte Carlo method and are typically 20% and 60%, respectively, for field data, and depend on the magnitude of the hydraulic gradient and the uncertainty in head measurements. The primary advantages of the tube seepage meter are its small footprint, concurrent and colocated assessments of q and K, and that it can also be configured as a self‐purging groundwater‐sampling device.  相似文献   

8.
By modifying a previous method with constant elements, we developed a quadratic element method for more accurately estimating groundwater flow by the inversion of tilt data. In this method: (1) a region of groundwater flow is divided into quadratic elements in which the change in groundwater volume per unit volume of rock (Δv) and the Skempton coefficient (B) vary in a quadratic manner with the coordinates, (2) the values of Δv are set to zero at the boundaries of the region of groundwater flow and (3) the sum of the squared second derivatives of Δv is adopted as a constraining condition that is weighted and added to the sum of the squared errors in tilt. First, analyses were performed for a flow model to determine the accuracy of this method for estimating groundwater flow and also to clarify the effect of the assumed size of a region of groundwater flow. These analyses showed that the quadratic element method proposed in this study gives a much better estimation of Δv than the constant element method and that a large region of groundwater flow should be assumed, rather than a small region, since the values of Δv at points outside of the actual region of groundwater flow are estimated to be nearly zero when a large region is assumed while these values are greatly overestimated when an excessively small region is assumed. Finally, the quadratic element method was applied to the site of the Mizunami Underground Research Laboratory in the Tono area, Japan. Inverse analyses were performed for tilt data measured by four tiltmeters with a resolution of 10−9 radians during the excavation of two shafts under the assumption that the rock mass is an isotropic and homogeneous half- space. The results showed that the method proposed in this study reproduced the tilt data very accurately. Thus, the distribution of Δv was estimated without sacrificing the reproducibility of the tilt data. The contour maps of B(1 + ν)Δv (ν: Poisson’s ratio) showed that the heterogeneous flow of groundwater occurred at the site and that groundwater volume decreased mainly in the area surrounded by two faults. The latter result is consistent with the finding obtained by previous investigations that these faults have low permeability in the direction perpendicular to the strike and may act as a flow barrier.  相似文献   

9.
Alan R. Hill 《水文研究》2012,26(20):3135-3146
The effect of preferential flow in soil pipes on nitrate retention in riparian zones is poorly understood. The characteristics of soil pipes and their influence on patterns of groundwater transport and nitrate dynamics were studied along four transects in a 1‐ to >3‐m deep layer of peat and marl overlying an oxic sand aquifer in a riparian zone in southern Ontario, Canada. The peat‐marl deposit, which consisted of several horizontal layers with large differences in bulk density, contained soil pipes that were generally 0.1 to 0.2 m in diameter and often extended vertically for 1 to >2 m. Springs that produced overland flow across the riparian area occurred at some sites where pipes extended to the peat surface. Concentrations of NO3?–N (20–30 mg L?1) and dissolved oxygen (DO) (4–6 mg L?1) observed in peat pipe systems and surface springs were similar to values in the underlying sand aquifer, indicating that preferential flow transported groundwater with limited nitrate depletion. Low NO3?–N concentrations of <5 mg L?1 and enriched δ15N values indicated that denitrification was restricted to small areas of the peat where pipes were absent. Groundwater DO concentrations declined rapidly to <2 mg L?1 in the peat matrix adjacent to pipes, whereas high NO3?–N concentrations of >15 mg L?1 extended over a larger zone. Low dissolved organic carbon values at these locations suggest that supplies of organic carbon were not sufficient to support high rates of denitrification, despite low DO conditions. These data indicate that it is important to develop a greater understanding of pipes in peat deposits, which function as sites where the transport of large fluxes of water with low biogeochemical reaction rates can limit the nitrate removal capacity of riparian zones. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

10.
The hydraulic conductivity (K) of many low permeability materials is strongly scale‐dependent. In raised mires and other types of peat deposit the effects of features such as abandoned infilled ditches, root holes and localized woody material, cause K to be heterogeneous and scale‐dependent. Despite this, field measurements are routinely made using auger hole (slug) tests at the scale of only a few tens of centimetres. Such measurements are locally valid, but where the regional subsurface movement of water through peat bogs is simulated using groundwater models, typically at the scale of hundreds of metres, they give rise to a systematic underestimate of flows and an overprediction of water table elevations. Until now, techniques to obtain values at a scale sufficiently large to include the effects of localized features of higher permeability have not been applied routinely. Research at Thorne Moor, a large raised mire, demonstrates that the K of peat varies over several orders of magnitude when measured at different scales, using a variety of techniques. Laboratory and auger hole tests cannot be relied upon to provide results that represent the hydraulic conductivity of large expanses of peatland. This has significant implications for the management and long‐term restoration of peatlands where both regional and local control of water levels is crucial. For groundwater models to be used successfully to plan such schemes, it is essential to apply the K values relevant to the scale of the simulation. This paper describes and tests novel techniques, using ditches, for the derivation of K at large scales which overcome many of the problems that have been identified with conventional techniques and are capable of producing estimates that are appropriate to the application of physically based regional flow models. Copyright © 2004 John Wiley & Sons, Ltd.  相似文献   

11.
The hydraulic properties of aquitards are not easily obtained because monitoring wells are usually installed in aquifers for groundwater resources management. Earthquake‐induced crust stress (strain) triggers groundwater level variations over a short period of time in a large area. These groundwater anomalies can be used to investigate aquifer systems. This study uses a poroelastic model to fit the postseismic variations of groundwater level triggered by the Chi‐Chi earthquake to evaluate the hydraulic properties of aquitards in the Jhoushuei River alluvial fan (JRAF), Taiwan. Six of the adopted eight wells with depths of 70 to 130 m showed good agreement with the recovery theory. The mean hydraulic conductivities (K) of the aquifers for the eight wells are 1.62 × 10?4 to 9.06 × 10?4 m/s, and the thicknesses are 18.8 to 46.1 m. The thicknesses of the aquitards are 11.3 to 42.0 m. Under the isotropic assumption for K, the estimated values of K for the aquitards are 3.0 × 10?8 to 2.1 × 10?6 m/s, corresponding to a silty medium. The results match the values obtained for the geological material of the drilling core and those reported in previous studies. The estimated values were combined with those given in previous studies to determine the distribution of K in the first two aquitards in the JRAF. The distribution patterns of the aquitards reflect the sedimentary environments and fit the geological material. The proposed technique can be used to evaluate the K value of aquitards using inverse methods. The inversion results can be used in hydrogeological analyses, contaminant modeling, and subsidence evaluation.  相似文献   

12.
Our understanding of hydraulic properties of peat soils is limited compared with that of mineral substrates. In this study, we aimed to deduce possible alterations of hydraulic properties of peat soils following degradation resulting from peat drainage and aeration. A data set of peat hydraulic properties (188 soil water retention curves [SWRCs], 71 unsaturated hydraulic conductivity curves [UHCs], and 256 saturated hydraulic conductivity [Ks] values) was assembled from the literature; the obtained data originated from peat samples with an organic matter (OM) content ranging from 23 to 97 wt% (weight percent; and according variation in bulk density) representing various degrees of peat degradation. The Mualem‐van Genuchten model was employed to describe the SWRCs and UHCs. The results show that the hydraulic parameters of peat soils vary over a wide range confirming the pronounced diversity of peat. Peat decomposition significantly modifies all hydraulic parameters. A bulk density of approximately 0.2 g cm?3 was identified as a critical threshold point; above and below this value, macroporosity and hydraulic parameters follow different functions with bulk density. Pedotransfer functions based on physical peat properties (e.g., bulk density and soil depth) separately computed for bog and fen peat have significantly lower mean square errors than functions obtained from the complete data set, which indicates that not only the status of peat decomposition but also the peat‐forming plants have a large effect on hydraulic properties. The SWRCs of samples with a bulk density of less than 0.2 g cm?3 could be grouped into two to five classes for each peat type (botanical composition). The remaining SWRCs originating from samples with a bulk density of larger than 0.2 g cm?3 could be classified into one group. The Mualem‐van Genuchten parameter values of α can be used to estimate Ks if no Ks data are available. In conclusion, the derived pedotransfer functions provide a solid instrument to derive hydraulic parameter values from easily measurable quantities; however, additional research is required to reduce uncertainty.  相似文献   

13.
This article presents the results of a field investigation of saturated hydraulic conductivity Ksat and bulk density (ρbd) in an Atlantic blanket bog in the southwest of Ireland. Starting at a peatland stream and moving along an uphill transect toward the peatland interior, ρbd and Ksat were examined at regular intervals. Saturated horizontal hydraulic conductivity (Khsat) and vertical (Kvsat) was estimated at two depths: 10–20 and 30–40 cm below the peat surface, whereas ρbd was estimated for the full profile. We consider two separate zones, one a riparian zone extending 10 m from the stream and a second zone in the bog interior. We found that the Ksat was higher (~10–5 m s–1) in the bog interior than that in the riparian zone (~10–6 m s–1), whereas the converse applied to bulk density, with lowest density (~0.055 g cm–3) at the interior and highest (~0.11 g cm–3) at the riparian zone. In general, we found Khsat to be approximately twice the Kvsat. These results support the idea that the lower Ksat at the margins control the hydrology of blanket peatlands. It is therefore important that the spatial variation of these two key properties be accommodated in hydrological models if the correct rainfall runoff characteristics are to be correctly modelled. Stream flow analysis over 3 years at the peatland catchment outlet showed that the stream runoff was composed of 8% base flow and 92% flood flow, suggesting that this blanket peatland is a source rather than a sink for floodwaters. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

14.
Saturated hydraulic conductivity (K) is one of the most important parameters determining groundwater flow and contaminant transport in both unsaturated and saturated porous media. Although several well‐established laboratory methods exist for determining K, in situ measurements of this parameter remain very complex and scale dependent. Often, the limited accessibility of subsurface sediments for sampling means an additional impediment to our ability to quantify subsurface K heterogeneity. One potential solution is the use of outcrops as analogues for subsurface sediments. This paper investigates the use of air permeameter measurements on outcrops of unconsolidated sediments to quantify K and its spatial heterogeneity on a broad range of sediment types. The Neogene aquifer in northern Belgium is used as a case study for this purpose. To characterize the variability in K, 511 small‐scale air permeability measurements were performed on outcrop sediments representative over five of the aquifer's lithostratigraphic units. From these measurements, outcrop‐scale equivalent K tensors were calculated using numerical upscaling techniques. Validation of the air permeameter‐based K values by comparison with laboratory constant head K measurements reveals a correlation of 0.93. Overall, the results indicate that hand‐held air permeameters are very efficient and accurate tools to characterize saturated K, as well as its small‐scale variability and anisotropy on a broad range of unconsolidated sediments. The studied outcrops further provided a qualitative understanding of aquifer hydrostratigraphy and quantitative estimates about K variability at the centimetre‐scale to metre‐scale. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

15.
Remediation of subsurface contamination requires an understanding of the contaminant (history, source location, plume extent and concentration, etc.), and, knowledge of the spatial distribution of hydraulic conductivity (K) that governs groundwater flow and solute transport. Many methods exist for characterizing K heterogeneity, but most if not all methods require the collection of a large number of small‐scale data and its interpolation. In this study, we conduct a hydraulic tomography survey at a highly heterogeneous glaciofluvial deposit at the North Campus Research Site (NCRS) located at the University of Waterloo, Waterloo, Ontario, Canada to sequentially interpret four pumping tests using the steady‐state form of the Sequential Successive Linear Estimator (SSLE) ( Yeh and Liu 2000 ). The resulting three‐dimensional (3D) K distribution (or K‐tomogram) is compared against: ( 1 ) K distributions obtained through the inverse modeling of individual pumping tests using SSLE, and ( 2 ) effective hydraulic conductivity (Keff) estimates obtained by automatically calibrating a groundwater flow model while treating the medium to be homogeneous. Such a Keff is often used for designing remediation operations, and thus is used as the basis for comparison with the K‐tomogram. Our results clearly show that hydraulic tomography is superior to the inversions of single pumping tests or Keff estimates. This is particularly significant for contaminated sites where an accurate representation of the flow field is critical for simulating contaminant transport and injection of chemical and biological agents used for active remediation of contaminant source zones and plumes.  相似文献   

16.
  相似文献   

17.
The Malloryville Wetland Complex, a small kettle-hole peatland, contains a diversity of peatland types. The wetland has a ‘rich’ side that contains wetland vegetation associated with solute-rich, near-neutral pH (minerotrophic) water, and a ‘poor’ side containing vegetation that grows in solute-poor and acidic (ombrotrophic) water. Vertical head gradients at piezometer clusters located in the rich side clearly show that groundwater is moving upwards towards the land surface, consistent with the vegetation types and surface water quality. In contrast, vertical head gradients also show that groundwater is moving upward in the poor side even though the vegetation and surface water chemistry are not minerotrophic. An incipient raised bog in the center of the poor side is the only site where groundwater moves consistently downward.

A peat core collected at the bog center shows that the bog site was initially covered by minerotrophic vegetation, typically found in groundwater discharge zones, which was later replaced by ombrotrophic bog vegetation. Theoretical computer simulation experiments of the bog hydrogeologic setting through time suggest that the direction of vertical groundwater flow at the bog site permanently changed from up to down when a water table mound developed under a convex-shaped fen peat mound that probably formed because of differential peat accumulation. Ombrotrophic conditions and bog vegetation probably began when the fen water table mound grew sufficiently large enough to divert the upward movement of regional groundwater. The transition from rich to poor environments probably occurred when the wetland water table was substantially below the elevation of the surrounding regional water table.  相似文献   


18.
The analysis of hydrogeological problems arising in bog watering by methods enabling the depth to groundwater table to be controlled was used to develop a method for estimating the efficiency of such control when data for directly solving groundwater flow problems are lacking. The effect of nonmonotone dependence of the rate of groundwater level rise on the hydraulic conductivity of peat underlain by high-permeability sand rocks is described. This effect is shown to be significant in assessing the potentialities of the operational control of groundwater level in bog massifs with this type of geological structure.  相似文献   

19.
Fine‐scale dynamics of groundwater flow were studied in a 1·5 ha peatland in central New York. Measurements of the hydraulic head throughout a detailed network of piezometer clusters revealed spatial and temporal variability in the direction of groundwater flow at a very fine (within a few metres) scale of analysis. Within the small wetland, there were areas of groundwater recharge, discharge and lateral flow. Such patterns of groundwater flow frequently reversed or changed due to fluctuations of only a few centimetres in hydraulic head. Specific conductance, deuterium signatures and calcium concentrations of groundwater corroborated the groundwater flow patterns determined with hydraulic head measurements and illustrated the influence of source water chemistry and evaporation on different layers in the peat column. The control of peat chemistry by such fine‐scale groundwater flow may have important implications for plant community composition and diversity in groundwater‐fed peatlands. Copyright © 1999 John Wiley & Sons, Ltd.  相似文献   

20.
The form and functioning of peatlands depend strongly on their hydrological status, but there are few data available on the hydraulic properties of tropical peatlands. In particular, the saturated hydraulic conductivity (K) has not previously been measured in neotropical peatlands. Piezometer slug tests were used to measure K at two depths (50 and 90 cm) in three contrasting forested peatlands in the Peruvian Amazon: Quistococha, San Jorge and Buena Vista. Measured K at 50 cm depth varies between 0.00032 and 0.11 cm s?1, and at 90 cm, it varies between 0.00027 and 0.057 cm s?1. Measurements of K taken from different areas of Quistococha showed that spatial heterogeneity accounts for ~20% of the within‐site variance and that depth is a good predictor of K. However, K did not vary significantly with depth at Buena Vista and San Jorge. Statistical analysis showed that ~18% of the variance in the K data can be explained by between‐site differences. Simulations using a simple hydrological model suggest that the relatively high K values could lead to lowering of the water table by >10 cm within ~48 m of the peatland edge for domed peatlands, if subjected to a drought lasting 30 days. However, under current climatic conditions, even with high K, peatlands would be unable to shed the large amount of water entering the system via rainfall through subsurface flow alone. We conclude that most of the water leaves these peatlands via overland flow and/or evapotranspiration. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号