首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 500 毫秒
1.
Local site conditions substantially affect the characteristics of seismic waves and its potential to cause earthquake damage. To accurately identify the variation of seismic hazard at different locations within the cities, measurements from a three-component station may be used for estimating the resonance frequencies and evaluate the expected level of damage at each site. This information can also be complemented with array measurements of ambient noise in order to estimate the Vs profiles and characterize the corresponding sediment layers at each site.  相似文献   

2.
Throughout their long history, the towns of Lod and Ramle have been severely affected by strong earthquakes. The last destructive earthquake occurred on July 11, 1927 and caused the destruction of large parts of these cities, reaching a seismic intensity of VIII–IX on the MSK scale. Such a high intensity from a relatively distant earthquake (about 70 km) of magnitude 6.2 is likely to be the result of local site effects of the sedimentary layers that may have significantly enhanced earthquake ground motions. This study is focused on estimating the seismic hazard to Lod and Ramle by implementing a three-step process (1) detailed mapping of the characteristics of the H/V spectral ratios from ambient noise, (2) incorporating geological information and well data to construct subsurface models for different sites within the investigated area and (3) estimating the seismic hazard in terms of uniform hazard site-specific accelerations. The horizontal-to-vertical spectral ratios of ambient noise were used to approximate the fundamental resonance frequencies of the subsurface and their associated amplitudes. About 360 sites in Lod and Ramle were instrumented for varying periods. The soil sites exhibits H/V peak amplitudes ranging from 4 to 6 in the frequency range 0.5–2.5 Hz. These data were used to constrain 1-D subsurface models that were developed using geological data and borehole information. H/V spectral ratio observations were checked against theoretical subsurface transfer functions at locations where borehole information is available farther constraint the range of possible Vs velocities of the different layers and thus, by means of trial an error it was possible to conclude a systematic spatial distribution of the Vs velocity and thickness in the substrata that are also consistent with the spatial distribution of the fundamental resonance frequencies of the soft sediments obtained by means of the H/V spectral ratios, and other geological and geophysical information available at different locations in the study area. The evaluated subsurface models are introduced using the SEEH procedure of Shapira and van~Eck [(1993) Natural Hazards 8, 201–205] to assess Uniform Hazard Site-Specific Acceleration Spectra for different zones within the towns of Lod and Ramle. These evaluations are very important for realistic assessment of the vulnerabilities of all types of existing and newly designed structures and for urban and land use planning.  相似文献   

3.
In this contribution, new relationship between the fundamental site frequency and the thickness of soft sediments is obtained for many sites in Egypt. The Horizontal-to-Vertical Spectral Ratio (“H/V”) technique (known as Nakamura technique) can be used as a robust tool to determine the thickness of soft sediments layers overlaying bedrock from observations and measurements of seismic ambient noise data. In Egypt, numerous seismic ambient noise measurements have been conducted in several areas to determine the dynamic properties of soft soil for engineering purposes. At each site in each studied area, the fundamental site frequency was accurately estimated from the main peak in the spectral ratio between the horizontal and vertical component. Consequently, an extensive database of microtremor measurements, well logging data, and shallow seismic refraction data have been configured and assembled for the studied areas. New formula between fundamental site frequency (f0) and thickness of soft sediments (h) is established. The new formula has been validated and compared with other formulas of earlier scientists, and the results indicate that the calculated depth and geometry of the bedrock surface using new formula are in a good agreement with well logs data and previously published seismic refraction surveys in the investigated sites.  相似文献   

4.
It has been two decades since the last comprehensive standard model of ambient earth noise was published Peterson (Observations and modelling of seismic background noise, US Geological Survey, open-file report 93–322, 1993). The PETERSON model was updated by analyzing the absolute quietest conditions for stations within the GSN (Berger et al. in J Geophys Res 109, 2005; Mcnamara and Buland in Bull Seism Soc Am 94:1517–1527, 2004; Ringler et al. in Seismol Res Lett 81(4) doi:10.1785/gssrl.81.4.605, 2010). Unfortunately, both the original model and the updated models did not include any deployed station in North Africa and Middle East, which reflects the noise levels within the desert environment of those regions. In this study, a survey was conducted to create a new seismic noise model from very broadband stations which recently deployed in North Africa. For this purpose, 1 year of continuous recording of seismic noise data of the Egyptian National Seismic Network (ENSN) was analyzed in order to create a new noise model. Seasonal and diurnal variations in noise spectra were recorded at each station. Moreover, we constructed a new noise model for each individual station. Finally, we obtained a new cumulative noise model for all the stations. We compared the new high-noise model (EHNM) and new low-noise model (ELNM) with both the high-noise model (NHNM) and low-noise model (NLNM) of Peterson (Observations and modelling of seismic background noise, US Geological Survey, open-file report 93–322, 1993). The obtained noise levels are considerably lower than low-noise model of Peterson (Observations and modelling of seismic background noise, US Geological Survey, open-file report 93–322, 1993) at ultra long period band (ULP band), but they are still below the high-noise model of Peterson (Observations and modelling of seismic background noise, US Geological Survey, open-file report 93–322, 1993). The results of this study could be considered as a first step to create permanent seismic noise models for North Africa and Middle East regions.  相似文献   

5.
Subsurface lithology and seismic site classification of Lucknow urban center located in the central part of the Indo-Gangetic Basin (IGB) are presented based on detailed shallow subsurface investigations and borehole analysis. These are done by carrying out 47 seismic surface wave tests using multichannel analysis of surface waves (MASW) and 23 boreholes drilled up to 30 m with standard penetration test (SPT) N values. Subsurface lithology profiles drawn from the drilled boreholes show low- to medium-compressibility clay and silty to poorly graded sand available till depth of 30 m. In addition, deeper boreholes (depth >150 m) were collected from the Lucknow Jal Nigam (Water Corporation), Government of Uttar Pradesh to understand deeper subsoil stratification. Deeper boreholes in this paper refer to those with depth over 150 m. These reports show the presence of clay mix with sand and Kankar at some locations till a depth of 150 m, followed by layers of sand, clay, and Kankar up to 400 m. Based on the available details, shallow and deeper cross-sections through Lucknow are presented. Shear wave velocity (SWV) and N-SPT values were measured for the study area using MASW and SPT testing. Measured SWV and N-SPT values for the same locations were found to be comparable. These values were used to estimate 30 m average values of N-SPT (N 30) and SWV (V s 30 ) for seismic site classification of the study area as per the National Earthquake Hazards Reduction Program (NEHRP) soil classification system. Based on the NEHRP classification, the entire study area is classified into site class C and D based on V s 30 and site class D and E based on N 30. The issue of larger amplification during future seismic events is highlighted for a major part of the study area which comes under site class D and E. Also, the mismatch of site classes based on N 30 and V s 30 raises the question of the suitability of the NEHRP classification system for the study region. Further, 17 sets of SPT and SWV data are used to develop a correlation between N-SPT and SWV. This represents a first attempt of seismic site classification and correlation between N-SPT and SWV in the Indo-Gangetic Basin.  相似文献   

6.
Local site effect microzonation of Lorca town (SE Spain)   总被引：1，自引：0，他引：1  
Local site effect assessment based on subsurface ground conditions is often the key to evaluate urban seismic hazard. The site effect evaluation in Lorca town (south-eastern Spain) started with a classification of urban geology through the geological mapping at scale 1:10,000 and the use of geotechnical data and geophysical surveys. The 17 geological formations identified were classified into 5 geological/seismic formations according to their seismic amplification capacity obtained from ambient vibration measurements as well as from simultaneous strong motion records. The shear-wave velocity structure of each geological/seismic formation was evaluated by means of inversion of Rayleigh wave dispersion data obtained from vertical-component array records of ambient noise. Nakamura’s method was applied to determine a predominant period distribution map. The spectral amplification factors were fourfold the values recorded in a reference hard-rock site. Finally, the capability of this study for explaining the damage distribution caused by the May 11th, 2011 Lorca destructive earthquake (Mw \(=\) 5.2) was examined. The methods used in this work are of assistance to evaluate ground amplification phenomena in urban areas of complex geology as Lorca town due to future earthquakes with applicability on urban seismic risk management.  相似文献   

7.
The International Data Centre (IDC) in Vienna, Austria, is determining, as part of automatic processing, sensor noise levels for all seismic, hydroacoustic, and infrasound (SHI) stations in the International Monitoring System (IMS) operated by the Provisional Technical Secretariat of the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO). Sensor noise is being determined several times per day as a power spectral density (PSD) using the Welch overlapping method. Based on accumulated PSD statistics a probability density function (PDF) is also determined, from which low and high noise curves for each sensor are extracted. Global low and high noise curves as a function of frequency for each of the SHI technologies are determined as the minimum and maximum of the individual station low and high noise curves, respectively, taken over the entire network of contributing stations. An attempt is made to ensure that only correctly calibrated station data contributes to the global noise models by additionally considering various automatic detection statistics. In this paper global low and high noise curves for 2010 are presented for each of the SHI monitoring technologies. Except for a very slight deviation at the microseism peak, the seismic global low noise model returns identically the Peterson (1993) NLNM low noise curve. The global infrasonic low noise model is found to agree with that of Bowman et al. (2005, 2007) but disagrees with the revised results presented in Bowman et al. (2009) by a factor of 2 in the calculation of the PSD. The global hydroacoustic low and high noise curves are found to be in quantitative agreement with Urick’s oceanic ambient noise curves for light to heavy shipping. Whale noise is found to be a feature of the hydroacoustic high noise curves at around 15 and 25 Hz.  相似文献   

8.
Three-dimensional frequency dependent S-wave quality factor (Qβ(f)) value for the central Honshu region of Japan has been determined in this paper using an algorithm based on inversion of strong motion data. The method of inversion for determination of three-dimensional attenuation coefficients is proposed by Hashida and Shimazaki (J Phys Earth. 32, 299–316, 1984) and has been used and modified by Joshi (Curr Sci. 90, 581–585, 2006; Nat Hazards. 43, 129–146, 2007) and Joshi et al. (J. Seismol. 14, 247–272, 2010). Twenty-one earthquakes digitally recorded on strong motion stations of Kik-net network have been used in this work. The magnitude of these earthquake ranges from 3.1 to 4.2 and depth ranging from 5 to 20 km, respectively. The borehole data having high signal to noise ratio and minimum site effect is used in the present work. The attenuation structure is determined by dividing the entire area into twenty-five three-dimensional blocks of uniform thickness having different frequency-dependent shear wave quality factor. Shear wave quality factor values have been determined at frequencies of 2.5, 7.0 and 10 Hz from record in a rectangular grid defined by 35.4°N to 36.4°N and 137.2°E to 138.2°E. The obtained attenuation structure is compared with the available geological features in the region and comparison shows that the obtained structure is capable of resolving important tectonic features present in the area. The proposed attenuation structure is compared with the probabilistic seismic hazard map of the region and shows that it bears some remarkable similarity in the patterns seen in seismic hazard map.  相似文献   

9.
The work presented in this paper lies under the scope of a research program aiming to assess the impact of deep coal mining induced vibrations on the surface constructions. The concerned section of the program is dedicated to the study of geological site effects and their influence on the mining induced vibrations for which the experimental investigations have been carried out and developed in this paper (Part 1). The empirical methods based on H/V spectral ratios have been applied on data sets provided from mining induced vibrations recorded within private residences above the deep coalmine as well as complementary measurements of ambient noise. The results evidence an amplified zone in the southern part of the Gardanne basin where drilling data confirmed the presence of particularly fractured and soft stratigraphic units. This joint analysis of induced seismicity and ambient noise enabled to validate the method based on H/V ratios applied to the mining context.  相似文献   

10.
The Algiers–Boumerdes regions were hit by an M w 6.8 destructive earthquake on May 21, 2003. The accelerometric and seismometric networks successfully recorded the main shock and many aftershocks at some locations where the damage was most extensive. A microtremor measurement was performed in the same locations; some of them are localized on the Mitidja basin. In this paper, we propose to analyze earthquake-induced site effect derived from horizontal to vertical spectral ratio from ambient noise (noise horizontal to vertical—NHV), or from very weak, weak, moderate and strong ( peak ground acceleration—PGA >10 % g) seismic motions (EHV), and transfer function evaluation from soil velocity profile data at four sites. H/V spectral ratios are computed by using both Fourier and response spectra. Compared to the transfer function, the obtained results show that in the case of soft soils, NHV as well as EHV give a good estimation of the soil's fundamental frequency, whereas the NHV underestimate the H/V amplitude and the EHV amplitude increase with the seismic motion intensity. In the case of firm soils, whereas the NHV gives flat curves synonymous for a rock site or a bump, the EHV is more appropriate as seen by identifying clear peaks with non negligible amplitude. In the case of soft sites as well as in the case of firm sites, strong peaks at frequencies higher than the fundamental one are found from EHV curves. Those peaks would not be found when looking at NHV ratios alone, are evidenced by the computed transfer function as well as by an analytical formulation, and are in agreement with the observed distribution of damage during the M w 6.8 2003 Boumerdes earthquake. Finally, the same analysis is performed by using response spectra rather than Fourier spectra and leads to the same conclusions. Moreover, the calculation of the response spectra is more easily compared with the smoothing operation of the Fourier spectra.  相似文献   

11.
Unloaded natural rock masses are known to generate seismic signals (Green et al., 2006; Hainzl et al., 2006; Husen et al., 2007; Kraft et al., 2006). Following a 1,000 m3 mass failure into the Mediterranean Sea, centimeter-wide tensile cracks were observed to have developed on top of an unstable segment of the coastal cliff. Nanoseismic monitoring techniques (Wust-Bloch and Joswig, 2006; Joswig, 2008), which function as a seismic microscope for extremely weak seismic events, were applied to verify whether brittle failure is still generated within this unconsolidated sandstone mass and to determine whether it can be detected. Sixteen days after the initial mass failure, three small-aperture sparse arrays (Seismic Navigation Systems-SNS) were deployed on top of this 40-m high shoreline cliff. This paper analyzes dozens of spiky nanoseismic (?2.2 ≥ M L ≥ ?3.4) signals recorded over one night in continuous mode (at 200 Hz) at very short slant distances (3–67 m). Waveform characterization by sonogram analysis (Joswig, 2008) shows that these spiky signals are all short in duration (>0.5 s). Most of their signal energy is concentrated in the 10–75 Hz frequency range and the waveforms display high signal similarity. The detection threshold of the data set reaches M L ?3.4 at 15 m and M L ?2.7 at 67 m. The spatial distribution of source signals shows 3-D clustering within 10 m from the cliff edge. The time distribution of M L magnitude does not display any decay pattern of M L over time. This corroborates an unusual event decay over time (modified Omori’s law), whereby an initial quiet period is followed by regained activity, which then fades again. The polarization of maximal waveform amplitude was used to estimate spatial stress distribution. The orientation of ellipses displaying maximal signal energy is consistent with that of tensile cracks observed in the field and agrees with rock mechanics predictions. The M L– surface rupture length relationship displayed by our data fits a constant-slope extrapolation of empirical data collected by Wells and Coppersmith (1994) for normal fault features at much larger scale. Signal characterization and location as well as the absence of direct anthropogenic noise sources near the monitoring site, all indicate that these nanoseismic signals are generated by brittle failure within the top section of the cliff. The atypical event decay over time that was observed suggests that the cliff material is undergoing post-collapse bulk strain accommodation. This feasibility study demonstrates the potential of nanoseismic monitoring in rapidly detecting, locating and analyzing brittle failure generated within unconsolidated material before total collapse occurs.  相似文献   

12.
  相似文献   

13.
A probabilistic relation between seismic activity and the volumeV of extracted deposits in mines is derived $$\Sigma E = C \cdot V^B ,$$ whereC andB are parameters characterizing mining works and the state of rock mass. Assuming that the measure of seismic hazard is the amount of seismic energy released in a given time interval, it is shown how the hazard can be evaluated continuously. The derived relations were tested in selected coal mines in Upper Silesia.  相似文献   

14.
背景噪声层析成像技术已被广泛应用于地壳和上地幔速度结构的研究,这种方法不依靠地震的发生和人工源爆破,只需记录连续的噪声信号而无需产生信号,因为噪声穿过地下介质时会携带信息,然后通过利用台站记录到的连续背景噪声数据进行互相关计算和叠加,即可得到台站间的经验格林函数,从而获取对地下结构的认识。这种方法已经很好地应用于中国的东北地区、华北克拉通、青藏高原以及华南地区,并成功地揭示了这些地区地壳与上地幔顶部的速度结构。此外近年来,一些学者还利用噪声互相关技术研究地下介质地震波速度随时间的变化,通过对汶川大地震前后连续噪声记录的研究发现,大震发生后呈现同震波速降低和震后波速逐渐恢复的特点,这表明可以通过观测地震波特性的变化来监测地下应力的变化,从而为大震的预测预防工作提供科学依据。本文主要综述了近些年来背景噪声技术及其在中国大陆地区的应用。  相似文献   

15.
Nakamura (Q Rep Railway Tech Res Inst 30:25–33, 1989) popularized the application of the horizontal-to-vertical spectral ratio (HVSR) analysis of microtremor (seismic noise or ambient vibration) recordings to estimate the predominant frequency and amplification factor of earthquake shaking. During the following quarter century, popularity in the microtremor HVSR (MHVSR) method grew; studies have verified the stability of a site’s MHVSR response over time and validated the MHVSR response with that of earthquake HVSR response. Today, MHVSR analysis is a popular reconnaissance tool used worldwide for seismic microzonation and earthquake site characterization in numerous regions, specifically, in the mapping of site period or fundamental frequency and inverted for shear-wave velocity depth profiles, respectively. However, the ubiquity of MHVSR analysis is predominantly a consequence of its ease in application rather than our full understanding of its theory. We present the state of the art in MHVSR analyses in terms of the development of its theoretical basis, current state of practice, and we comment on its future for applications in earthquake site characterization.  相似文献   

16.
In this paper we describe a stable automatic method to estimate in real time the seismic moment, moment magnitude and corner frequency of events recorded by a network comprising broad-band and accelerometer sensors. The procedure produces reliable results even for small-magnitude events $\hbox {M}_{\mathrm{W}}\approx 3$ . The real-time data arise from both the Transfrontier network at the Alps-Dinarides junction and from the Italian National Accelerometric Network (RAN). The data is pre-processed and the S-wave train identified through the application of an automatic method, which estimates the arrival times based on the hypocenter location, recording site and regional velocity model. The transverse component of motion is used to minimize conversion effects. The source spectrum is obtained by correcting the signals for geometrical spreading and intrinsic attenuation. Source spectra for both velocity and displacement are computed and, following Andrews (1986), the seismic moment and the first estimate of the corner frequency, $f_{0}$ , derived. The procedure is validated using the recordings of some recent moderate earthquakes (Carnia 2002; Bovec 2004; Parma 2008; Aquila 2009; Macerata 2009; Emilia 2012) and the recordings of some minor events in the SE Alps area for which independent seismic moment and moment magnitude estimates are available. The results obtained with a dataset of 843 events recorded by the Transfrontier and RAN networks show that the procedure is reliable and robust for events with $\hbox {M}_{\mathrm{W}}\ge 3$ . The estimates of $f_{0}$ are less reliable. The results show a scatter, principally for small events with $\hbox {M}_{\mathrm{W}}\le 3$ , probably due to site effects and inaccurate locations.  相似文献   

17.
We made an attempt to assess the shear wave velocity values V S and, to a lesser extent, the V P values from ambient noise recordings in an array configuration. Five array sites were situated in the close proximity to borehole sites. Shear wave velocity profiles were modeled at these five array sites with the aid of two computational techniques, viz. spatial autocorrelation (SPAC) and H/V ellipticity. Out of these five array sites, velocity estimates could be reliably inferred at three locations. The shear wave velocities estimated by these methods are found to be quite consistent with each other. The computed V S values up to 30 m depth are in the range from 275 to 375 m/s in most of the sites, which implies prevalence of a low velocity zone at some pocket areas. The results were corroborated by evidence of site geology as well as geotechnical information.  相似文献   

18.
This paper estimates fundamental translational period and damping ratio parameters and examines the changes in dynamic characteristics of a set of low-to-medium rise buildings in Lorca town (SE of Spain) affected by the May 11th, 2011 earthquake. These building parameters have been calculated analysing structural dynamic response from ambient vibration measurements recorded at top RC buildings pre- and post earthquake, using the Fast Fourier Transform and the Randomdec technique. The empirical expression relating period \((T)\) and number of floor \((N)\) here obtained analysing ambient noise recorded on 59 healthy buildings before the earthquake is \(T= (0.054\pm 0.002)\, N\) , very similar to others empirical period–height relationships obtained for RC structures in the European built environment but quite different from code provisions. Measurements performed in 34 damaged buildings show a period elongation after the quake according to \(T^{*} =(0.075\pm 0.002)\,N\) expression. Moreover, we found a rise of the fundamental period with the EMS’s grade of damage of buildings. In contrast to natural frequency, damping ratio \((\xi )\) do not shows a significant variation with earthquake damage degree and the product \(\xi \, T\) remains near constant.  相似文献   

19.
The Load/Unload Response Ratio (LURR) method is a proposed technique to predict earthquakes that was first put forward by Yin (1987). LURR is based on the idea that when an area enters the damage regime, the rate of seismic activity during loading of the tidal cycle increases relative to the rate of seismic activity during unloading in the months to one year preceding a large earthquake. Since earth tides generally contribute the largest temporal variations in crustal stress, it seems plausible that earth tides would trigger earthquakes in areas that are close to failure (e.g., Vidale et al., 1998). However, the vast majority of studies have shown that earth tides do not trigger earthquakes (e.g., Vidale et al., 1998; Heaton, 1982; Rydelek et al., 1992). In this study, we conduct an independent test of the LURR method, since there would be important scientific and social implications if it were proven to be a robust method of earthquake prediction. Smith and Sammis (2004) undertook a similar study and found no evidence that there was predictive significance to the LURR method. We have repeated calculations of LURR for the Northridge earthquake in California, following both the parameters of X.C. Yin (personal communication) and the somewhat different ones of Smith and Sammis (2004). Though we have followed both sets of parameters closely, we have been unable to reproduce either set of results. Our examinations have shown that the LURR method is very sensitive to certain parameters. Thus it seems likely that the discrepancies between our results and those of previous studies are due to unaccounted for differences in the calculation parameters. A general agreement was made at the 2004 ACES Workshop in China between research groups studying LURR to work cooperatively to resolve the differences in methods and results, and thus permit more definitive conclusions on the potential usefulness of the LURR method in earthquake prediction.  相似文献   

20.
Seismic site characterization is the basic requirement for seismic microzonation and site response studies of an area. Site characterization helps to gauge the average dynamic properties of soil deposits and thus helps to evaluate the surface level response. This paper presents a seismic site characterization of Agartala city, the capital of Tripura state, in the northeast of India. Seismically, Agartala city is situated in the Bengal Basin zone which is classified as a highly active seismic zone, assigned by Indian seismic code BIS-1893, Indian Standard Criteria for Earthquake Resistant Design of Structures, Part-1 General Provisions and Buildings. According to the Bureau of Indian Standards, New Delhi (2002), it is the highest seismic level (zone-V) in the country. The city is very close to the Sylhet fault (Bangladesh) where two major earthquakes (M w > 7) have occurred in the past and affected severely this city and the whole of northeast India. In order to perform site response evaluation, a series of geophysical tests at 27 locations were conducted using the multichannel analysis of surface waves (MASW) technique, which is an advanced method for obtaining shear wave velocity (V s) profiles from in situ measurements. Similarly, standard penetration test (SPT-N) bore log data sets have been obtained from the Urban Development Department, Govt. of Tripura. In the collected data sets, out of 50 bore logs, 27 were selected which are close to the MASW test locations and used for further study. Both the data sets (V s profiles with depth and SPT-N bore log profiles) have been used to calculate the average shear wave velocity (V s30) and average SPT-N values for the upper 30 m depth of the subsurface soil profiles. These were used for site classification of the study area recommended by the National Earthquake Hazard Reduction Program (NEHRP) manual. The average V s30 and SPT-N classified the study area as seismic site class D and E categories, indicating that the city is susceptible to site effects and liquefaction. Further, the different data set combinations between V s and SPT-N (corrected and uncorrected) values have been used to develop site-specific correlation equations by statistical regression, as ‘V s’ is a function of SPT-N value (corrected and uncorrected), considered with or without depth. However, after considering the data set pairs, a probabilistic approach has also been presented to develop a correlation using a quantile–quantile (Q–Q) plot. A comparison has also been made with the well known published correlations (for all soils) available in the literature. The present correlations closely agree with the other equations, but, comparatively, the correlation of shear wave velocity with the variation of depth and uncorrected SPT-N values provides a more suitable predicting model. Also the Q–Q plot agrees with all the other equations. In the absence of in situ measurements, the present correlations could be used to measure V s profiles of the study area for site response studies.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号