首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 30 毫秒
1.
This article explores the possibility to measure deformations of building foundations from measurements of ambient noise and strong motion recordings. The case under study is a seven-storey hotel building in Van Nuys, California. It has been instrumented by strong motion accelerographs, and has recorded several earthquakes, including the 1971 San Fernando (ML=6.6, R=22 km), 1987 Whittier–Narrows (ML=5.9, R=41 km), 1992 Landers (ML=7.5, R=186 km), 1992 Big Bear (ML=6.5, R=149 km), and 1994 Northridge (ML=6.4, R=1.5 km) earthquake and its aftershocks (20 March: ML=5.2, R=1.2 km; 6 December, 1994: ML=4.3, R=11 km). It suffered minor structural damage in 1971 earthquake and extensive damage in 1994. Two detailed ambient vibration tests were performed following the Northridge earthquake, one before and the other one after the 20 March aftershock. These included measurements at a grid of points on the ground floor and in the parking lot surrounding the building, presented and analyzed in this article. The analysis shows that the foundation system, consisting of grade beams on friction piles, does not act as a “rigid body” but deforms during the passage of microtremor and therefore earthquake waves. For this geometrically and by design essentially symmetric building, the center of stiffness of the foundation system appears to have large eccentricity (this is seen both from the microtremor measurements and from the earthquake recordings). This eccentricity may have contributed to strong coupling of transverse and torsional responses, and to larger than expected torsional response, contributing to damage during the 1994 Northridge, earthquake.  相似文献   

2.
The majority of structural health monitoring methods are based on detecting changes in the modal properties, which are global characteristics of the structure, and are not sensitive to local damage. Wave travel times between selected sections of a structure, on the other hand, are local characteristics, and are potentially more sensitive to local damage. In this paper, a structural health monitoring method based on changes in wave travel times is explored using strong motion data from the Imperial Valley Earthquake of 1979 recorded in the former Imperial County Services (ICS) Building, severely damaged by this earthquake. Wave travel times are measured from impulse response functions computed from the recorded horizontal seismic response in three time windows—before, during, and after the largest amplitude response, as determined from previous studies of this building, based on analysis of novelties in the recorded response. The results suggest initial spatial distribution of stiffness consistent with the design characteristics, and reduction of stiffness following the major damage consistent with the spatial distribution of the observed damage. The travel times were also used to estimate the fundamental fixed-base frequency of the structure f1 (assuming the building deformed as a shear beam), and its changes during this earthquake. These estimates are consistent with previous estimates of the soil–structure system frequency, fsys, during the earthquakes (f1<fsys as expected from soil–structure interaction studies), and with other estimates of frequency (f1 from ETABS models, and fsys from ambient vibration tests, and “instantaneous” f1 from high-frequency pulse propagation).  相似文献   

3.
Following the Mw 7.3 Martinique earthquake, November 29th, 2007, a post-seismic survey was conducted by the Bureau Central Sismologique Français (BCSF) for macroseismic intensities assessment. In addition to the inventories, ambient vibration recordings were performed close to the particularly damaged zones in the free-field and the buildings. The objective of the paper is to show the relevancy of performing ambient vibration recordings for post-earthquake surveys. The analyses of the recordings aim at explaining the variability of the damages through site effects, structure vulnerability or resonance phenomena and to help the characterization of the post-seismic building integrity. In three sites prone to site effects, we suspect damage to be related to a concordance between soil fundamental frequency and building resonance frequency. Besides, the recordings of ambient vibrations at La Trinité hospital before and after the earthquake allow us to quantify the damage due to earthquake in terms of stiffness loss.  相似文献   

4.
The microtremor horizontal-to-vertical-spectral-ratio (HVSR) technique is widely used in the urban environment to assess the fundamental frequency response of the ground. Extensive literature exists about case histories using HVSR for microzonation in several cities, but no systematic studies have been devoted to check the presence of soil–structure interaction effects, and even less attention to study building behaviour after earthquake damage. To evaluate the above-mentioned effects, a series of experiments are reported in this article.We first made a series of microtremor measurements on buildings and civil structures to evaluate the reliability of fundamental frequency determinations. Then, we considered several case studies to evaluate the effect of soil–structure interaction in estimates of site response in the presence of tall buildings. Finally, an experiment on the frequency change due to damage was performed. It was possible to confirm that HVSR is able to detect building fundamental modes and once known the building frequency, it is also possible to detect the presence of soil–structure interaction. Thus, once the presence of the building natural frequency is identified, it is possible to infer the site response from free field measurements. We also found that the HVSR technique is equally useful for detecting structural damage by determining the frequency shift of the buildings.  相似文献   

5.
A shallow earthquake ofM S=6.2 occurred in the southern part of the Peloponnesus, 12 km north of the port of the city of Kalamata, which caused considerable damage. The fault plane solution of the main shock, geological data and field observations, as well as the distribution of foci of aftershocks, indicate that the seismic fault is a listric normal one trending NNE-SSW and dipping to WNW. The surface ruptures caused by the earthquake coincide with the trace of a neotectonic fault, which is located 2–3 km east of the city of Kalamata and which is related to the formation of Messiniakos gulf during the Pliocene-Quaternary tectonics. Field observations indicate that the earthquake is due to the reactivation of the same fault.A three-days aftershock study in the area, with portable seismographs, recorded many aftershocks of which 39 withM S1.7 were very well located. The distribution of aftershocks forms two clusters, one near the epicenter of the main shock in the northern part of the seismogenic volume, and the other near the epicenter of the largest aftershock (M S=5.4) in the southern part of this volume. The central part of the area lacks aftershocks, which probably indicates that this is the part of the fault which slipped smoothly during the earthquake.  相似文献   

6.
Three studies of site amplification factors, based on the recorded aftershocks, and one study based on strong motion data, are compared one with another and with the observed distribution of damage from the Northridge, CA, earthquake of 17 January 1994 (ML=6.4). In the epicentral area, when the peak ground velocities are larger than vm≈15 cm/s, nonlinear response of soil begins to distort the amplification factors determined from small amplitude (linear) wave motion. Moving into the area of near-field and strong ground motion (vm>30 cm/s), the site response becomes progressively more affected by the nonlinear soil response. Based on the published results, it is concluded that site amplification factors determined from small amplitude waves (aftershocks, small earthquakes, coda waves) and their transfer-function representation may be useful for small and distant earthquake motions, where soils and structures respond to earthquake waves in a linear manner. However in San Fernando Valley, during the Northridge earthquake, the observed distribution of damage did not correlate with site amplification determined from spectra of recorded weak motions. Mapping geographical distribution of site amplification using other than very strong motion data, therefore appears to be of little use for seismic hazard analyses.  相似文献   

7.
During the Mw=6.9 January 1, 1980 earthquake in the Azores, the damage distribution in the town of Angra do Heroísmo, in Terceira Island, had a non-homogeneous spatial character. In order to understand the observed pattern of damage a microtremor survey was carried out, using ambient vibrations, and the data were analysed with the J-Sesame software, following the H/V Nakamura methodology. The results are in good agreement with the surface geology and they show a good correlation with the observed damages. Two building surveys were performed, in 1980 on damage evaluation and in 2000 on characterization of few building parameters. With all these elements (surface geology type, soil peak frequency, building type, number of stories and damage level) for 2111 buildings it was possible to perform several interparameter analysis, which enabled the identification of indicators that could be used to improve the damage estimation for future events.  相似文献   

8.
Ambient vibration tests were conducted on a base-isolated apartment building in Takamatsu, Japan, to determine the mode shapes and the associated natural frequencies and damping ratios at very low levels of excitation. The latest developments in signal analysis for modal decomposition are used to analyze the ambient response data. A finite element model of the building and isolators was calibrated and refined using the experimental results from the ambient vibration tests. This model was then used to simulate the recorded response of the building under excitation from a small earthquake. The finite element model, calibrated by ambient vibration data and the low level of earthquake shaking, provides the starting point for modelling the non-linear response of the building when subjected to strong shaking.  相似文献   

9.
This paper presents low frequency wavenumbers in a seven-storey reinforced concrete building estimated from its recorded response to eleven earthquakes, one of which (1994 Northridge) caused visible structural damage, and two of which are its aftershocks. The wavenumbers, Ki,j(f), are estimated from pairs (i,j) of records at neighboring recording sites in the building, distributed vertically or horizontally. Changes in Ki,j(f) from one event to another are compared in the undamaged (lower) and in the damaged (upper) part of the building, with the aim to find whether trends in Ki,j(f) can indicate damage. The results suggest significant and permanent increase of the wavenumbers in the damaged parts for the 1994 Northridge earthquake and its aftershocks, which is not the case for the other events in the damaged parts, and for all eleven events in the undamaged parts of the building. This increase in wavenumbers in the damaged parts can be explained by reduced wave velocities through the damaged structural members, and by scattering of waves from the discontinuities created by the damage. It is concluded from this qualitative analysis that wavenumbers estimated from strong motion recordings in a building can indicate location of damage, and that it would be useful to refine further this method (extend it to higher frequencies, and add the capability to quantify the damage). However, this would require more dense strong motion instrumentation in buildings than currently available. Deployment of dense arrays in selected buildings would provide data for further work on this subject.  相似文献   

10.
In this study, we determine an updated finite element model of a reinforced concrete building—which was damaged from shaking during 1994 Northridge earthquake—using forced‐vibration test data and a novel model‐updating technique. Developed and verified in the companion paper (viz. BVLSrc, Earthquake Eng. Struct. Dyn. 2006; this issue), this iterative technique incorporates novel sensitivity‐based relative constraints to avoid ill conditioning that results from spatial incompleteness of measured data. We used frequency response functions and natural frequencies as input for the model‐updating problem. These data were extracted from measurements obtained during a white‐noise excitation applied at the roof of the building using a linear inertial shaker. Flexural stiffness values of properly grouped structural members, modal damping ratios, and translational and rotational mass values were chosen as the updating parameters, so that the converged results had direct physical interpretations, and thus, comparisons with common parameters used in seismic design and evaluation of buildings could be made. We investigated the veracity of the updated finite element model by comparing the predicted and measured dynamic responses under a second, and different type of forced (sine‐sweep) vibration, test. These results indicate that the updated model replicates the dynamic behaviour of the building reasonably well. Furthermore, the updated stiffness factors appear to be well correlated with the observed building damage patterns (i.e. their location and severity). Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

11.
以北京市防震减灾中心结构为例,进行了结构的地震反应观测及振动特性识别研究。基于半功率带宽法对结构脉动测试数据进行了分析,计算出了结构自振周期和振型以及相应的阻尼比。各振型都具有较大幅值的楼层分别位于3、6和8层,据此设计并建成了结构地震反应观测台阵。分析台阵地震记录识别出了结构的自振特性,同时功率谱曲线显示,井下数据存在高频特性,初步判定其来自钢套管振动。开展结构的数值模拟分析,利用观测楼层上地震记录的卓越频率不断修正结构数值模型,直至结构反应与地震记录的频率值相符,且与脉动测试数据基本一致,相对位移对比分析发现,在该模型基础上相对位移反应与相对位移记录基本吻合。结构地震反应观测和数值模拟分析较好地实现了结构地震反应观测台阵的观测目的。  相似文献   

12.
Three types of seismic data recorded near Coalinga, California were analyzed to study the behavior of scattered waves: 1) aftershocks of the May 2, 1983 earthquake, recorded on verticalcomponent seismometers deployed by the USGS; 2) regional refraction profiles using large explosive sources recorded on essentially the same arrays above; 3) three common-midpoint (CMP) reflection surveys recorded with vibrator sources over the same area. Records from each data set were bandpassed filtered into 5 Hz wide passbands (over the range of 1–25 Hz), corrected for geometric spreading, and fit with an exponential model of amplitude decay. Decay rates were expressed in terms of inverse codaQ (Q c –1 ).Q c –1 values for earthquake and refraction data are generally comparable and show a slight decrease with increasing frequency. Decay rates for different source types recorded on proximate receivers show similar results, with one notable exception. One set of aftershocks shows an increase ofQ c –1 with frequency.Where the amplitude decay rates of surface and buried sources are similar, the coda decay results are consistent with other studies suggesting the importance of upper crustal scattering in the formation of coda. Differences in the variation ofQ c –1 with frequency can be correlated with differences in geologic structure near the source region, as revealed by CMP-stacked reflection data. A more detailed assessment of effects such as the depth dependence of scattered contributions to the coda and the role of intrinsic attenuation requires precise control of source-receiver field geometry and the study of synthetic seismic data calculated for velocity models developed from CMP reflection data.  相似文献   

13.
The site response at 15 stations in the Adana-Ceyhan region (Southern Turkey) is calculated from the recordings of aftershocks of June 27, 1998 Adana-Ceyhan earthquake (MS=6.2) by using the Standard Spectral Ratio (SSR) and the Horizontal-to-Vertical Spectral Ratio (HVSR) methods. While the two methods are in good harmony at a few stations in determining the site effects, they show differences on the estimated amplifications or on the site resonance frequencies at most stations. It was not clear which one of the two methods underestimates or overestimates the amplification values. We observe that at some stations, where the local site conditions are rather complex, the vertical component records are strongly influenced from the local soil conditions. Thus, the HVSR method fails at these stations. The SSR method underestimates the amplifications at some stations since the rock site, selected as reference site, has its own site response and/or the path correction we applied, considering the geometrical spreading factor only, is insufficient. At the sites where high intensity values were observed, we found high amplifications. The fundamental soil frequencies characterize the damage properties observed in the Adana-Ceyhan earthquake. The fundamental soil frequency is nearly at 1.1 Hz at the Ceyhan site, where severe damage was observed in the 5–6 story buildings, while the fundamental soil frequency is between 3–6 Hz at the Adana site, where damage was in the low-story buildings. Therefore, in addition to inefficient construction practices, it is clear that the resonance effects have also contributed to the observed damage.  相似文献   

14.
An approach is formulated for the linear analysis of three-dimensional dynamic soil–structure interaction of asymmetric buildings in the time domain, in order to evaluate the seismic response behaviour of torsionally coupled buildings. The asymmetric building is idealized as a single-storey three-dimensional system resting on different soil conditions. The soil beneath the superstructure is modeled as linear elastic solid elements. The contact surface between foundation mat and solid elements of soil is discretised by linear plane interface elements with zero thickness. An interface element is further developed to function between the rigid foundation and soil. As an example, the response of soil–structure interaction of torsionally coupled system under two simultaneous lateral components of El Centro 1940 earthquake records has been evaluated and the effects of base flexibility on the response behaviour of the system are verified.  相似文献   

15.
A study on the seismic response of massive flexible strip-foundations embedded in layered soils and subjected to seismic excitation is presented. Emphasis is placed on the investigation of the system response with the aid of a boundary element–finite element formulation proper for the treatment of such soil–structure interaction problems. In the formulation, the boundary element method (BEM) is employed to overcome the difficulties that arise from modeling the infinite soil domain, and the finite element method (FEM) is applied to model the embedded massive flexible strip-foundation. The numerical solution for the soil–foundation system is obtained by coupling the FEM with the BEM through compatibility and equilibrium conditions at the soil–foundation and soil layer interfaces. A parametric study is conducted to investigate the effects of foundation stiffness and embedment on the seismic response.  相似文献   

16.
This paper presents a study of site effects in the urban area of Tecoman in Colima, Mexico. A variety of instruments (both accelerometers and seismometers) were used to record earthquakes and ambient vibration throughout the city. Earthquake records were analysed using several techniques to estimate site effects: spectral ratios relative to a reference station, spectral ratios of the horizontal components relative to the vertical recorded at the same site, and a parametric inversion of Fourier spectra. Ambient noise records were used to estimate a local transfer function using horizontal to vertical spectral ratios. The results show that local amplification at Tecoman is significant. Dominant frequency varies between 0.5 and 0.7 Hz, suggesting a large thickness of the soft sedimentary deposits. We did not observe systematic variations throughout the city. Our more reliable estimates indicate that maximum amplification is comprised between a factor 6 and 8. Comparisons among different sensors and recorders show that all combinations between velocimeters, accelerometers, and recorders provide reliable results provided that the electronic noise is smaller than the noise being recorded. This is notably not the case for accelerometers at quiet sites and for frequencies smaller than 2 Hz. This explains why previous studies disagree as to the usefulness of accelerometers to record ambient noise for site effect studies. This factor is, however, a function of noise amplitude at each site.  相似文献   

17.
Studies of structural responses and damage to high-frequency blast motion are very limited. Current practice uses some empirical allowable ground vibration limits in assessing structural performance. These empirical limits overlook the physical parameters that govern structural response and damage, such as the ground motion characteristics and inherent structural properties. This paper studies the response of RC frame structures to numerically simulated underground blast-induced ground motions. The structural response and damage characteristics of frame structures to ground motions of different frequencies are investigated first. The effects of blast ground motion spatial variations and soil–structure interaction on structural responses are also studied. A suitable discrete model that gives accurate response prediction is determined. A damage index defined based on the accumulated plastic hinge rotation is used to predict structural damage level. Numerical results indicated that both the low structural vibration modes (global modes) and the first elemental vibration mode (local) might govern the dynamic structural responses depending on the ground motion frequency and structural response parameters under consideration. Both ground motion spatial variations and soil–structure interaction effects are prominent. Neglecting them might yield inaccurate structural response prediction. The overall structural response and damage are highly ground motion frequency dependent. Numerical results of structural damage are also compared with some test results obtained in a previous study and with code specifications. Discussions on the adequacy of the code allowable ground vibration limits on RC frame structures are also made.  相似文献   

18.
In highly populated urban centers, traditional seismic survey sources can no longer be properly applied due to restrictions in modern civilian life styles. The ambient vibration noise, including both microseisms and microtremor, though are generally weak but available anywhere and anytime, can be an ideal supplementary source for conducting seismic surveys for engineering seismology and earthquake engineering. This is fundamentally supported by advanced digital signal processing techniques for effectively extracting the useful information out from the noise. Thus, it can be essentially regarded as a passive seismic method. In this paper we first make a brief survey of the ambient vibration noise, followed by a quick summary of digital signal processing for passive seismic surveys. Then the applications of ambient noise in engineering seismology and earthquake engineering for urban settings are illustrated with examples from Beijing metropolitan area. For engineering seismology the example is the assessment of site effect in a large area via microtremor observations. For earthquake engineering the example is for structural characterization of a typical reinforced concrete high-rise building using background vibration noise. By showing these examples we argue that the ambient noise can be treated as a new source that is economical, practical, and particularly valuable to engineering seismology and earthquake engineering projects for seismic hazard mitigation in urban areas.  相似文献   

19.
The paper highlights the use of fem and bi-directional lumped-mass-storey-stiffness numerical models for the study of the soil–structure interaction (ssi) effects on an instrumented building. Data on the structural response have been obtained through the project for seismic instrumentation of a 16-storey r/c cast-in-place dwelling building (Chisinau, Republic of Moldova) during a series of earthquakes (Gutenberg–Richter M GR = 5.0−6.7). The effect of soil–structure interaction is clearly observed comparing the responses recorded on foundation and free-field. ssi becomes more pronounced for higher level of ground shaking amplifying the natural period of the structure and slightly suppressing high frequences on the foundation in comparison with the free-field motion.  相似文献   

20.
In this paper, a simple two-dimensional soil–structure interaction model, based on Biot's theory of wave propagation in fluid saturated porous media, is used to explain the observed increase of the apparent frequencies of Millikan library in Pasadena, California, during heavy rainfall and recovery within days after the rain. These variations have been measured for small amplitude response (to microtremors and wind excitation), for which Biot's linear theory is valid. The postulated hypothesis is that the observed increases in frequency are due to the water saturation of the soil. The theoretical model used to explore this hypothesis consists of a shear wall supported by a circular foundation embedded in a poroelastic half-space. This rigid foundation model may be appropriate only for the NS response of Millikan library. This paper presents results for the foundation stiffness, and for the system response for model parameters similar to those for Millikan library (located on alluvium with shear wave velocity of about 300 m/s). The foundation impedance matrix, foundation input motion and system response are compared for dry and fully saturated half-space, with permeable and impermeable foundation. The results show that for embedded foundations, the effects of saturation on the horizontal foundation stiffness are as significant as for the vertical stiffness, contrary to what has been known for surface foundations investigated by other authors. Further, the results suggest a 1–2% increase in system frequency of the first two modes of vibration, depending on the drainage condition along the foundation–soil interface. Such increases agree qualitatively with the observations.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号