首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 484 毫秒
1.
In July 2007, new marine heat flow data were collected at ten sites (HF01–10) in the central and southwestern sectors of the Ulleung Basin (East Sea or Sea of Japan) as part of regional gas hydrate research. In addition, cores were collected at five of these sites for laboratory analysis. The results show that the geothermal gradient ranged from 103–137 mK/m, and the in-situ thermal conductivity from 0.82–0.95 W/m·K. Laboratory measurements of thermal conductivity were found to deviate by as much as 40% from the in-situ measurements, despite the precautions taken to preserve the cores. Based on the in-situ conductivity, the heat flow was found to increase with water depth toward the center of the basin, ranging from 84–130 mW/m2. Using a simple model, we estimated the heat flow from the depths of the BSR, and compared this with the observed heat flow. In our study area, the two sets of values were quite consistent, the observed heat flows being slightly higher than the BSR-derived ones. The evaluation of regional pre-1994 data revealed that the heat flow varied widely from 51–157 mW/m2 in and around the basin. Due to a large scatter in these older data, a clear relationship between heat flow and water depth was not evident, in contrast to what would be expected for a rifted sedimentary basin. This raises the question as to whether the pre-1994 data represent the true background heat flow from the underlying basin crust since the basin opening, and/or whether they contain large measurement errors. In fact, evidence in support of the latter explanation exists. BSRs are generally found in the deep parts of the basin, and vary by only ±15 m in depth below the seafloor. From the average BSR depth, we inferred the background heat flow using a simple model, which in the case of the Ulleung Basin is approximately 120 and 80 mW/m2 for 2.5 and 1 km below sea level, respectively.  相似文献   

2.
Drilling/coring activities onboard JOIDES Resolution for hydrate resource estimation have confirmed gas hydrate in the continental slope of Krishna-Godavari (KG) basin, Bay of Bengal and the expedition recovered fracture filled gas hydrate at the site NGHP-01-10. In this paper we analyze high resolution multi-channel seismic (MCS), high resolution sparker (HRS), bathymetry, and sub-bottom profiler data in the vicinity of site NGHP-01-10 to understand the fault system and thermal regime. We interpreted the large-scale fault system (>5 km) predominantly oriented in NNW-SSE direction near NGHP-01-10 site, which plays an important role in gas hydrate formation and its distribution. The increase in interval velocity from the baseline velocity of 1600 m/s to 1750–1800 m/s within the gas hydrate stability zone (GHSZ) is considered as a proxy for the gas hydrate occurrence, whereas the drop in interval velocity to 1400 m/s suggest the presence of free gas below the GHSZ. The analysis of interval velocity suggests that the high concentration of gas hydrate occurs close to the large-scale fault system. We conclude that the gas hydrate concentration near site NGHP-01-10, and likely in the entire KG Basin, is controlled primarily by the faults and therefore has high spatial variability.We also estimated the heat flow and geothermal gradient (GTG) in the vicinity of NGHP-01-10 site using depth and temperature of the seafloor and the BSR. We observed an abnormal GTG increase from 38 °C/km to 45 °C/km at the top of the mound, which remarkably agrees with the measured temperature gradient at the mound (NGHP-01-10) and away from the mound (NGHP-01-03). We analyze various geological scenarios such as topography, salinity, thermal non-equilibrium of BSR and fluid/gas advection along the fault system to explain the observed increase in GTG. The geophysical data along with the coring results suggest that the fluid advection along the fault system is the primary mechanism that explains the increase in GTG. The approximate advective fluid flux estimated based on the thermal measurement is of the order of few tenths of mm/yr (0.37–0.6 mm/yr).  相似文献   

3.
The Upper Cretaceous Mukalla coals and other organic-rich sediments which are widely exposed in the Jiza-Qamar Basin and believed to be a major source rocks, were analysed using organic geochemistry and petrology. The total organic carbon (TOC) contents of the Mukalla source rocks range from 0.72 to 79.90% with an average TOC value of 21.50%. The coals and coaly shale sediments are relatively higher in organic richness, consistent with source rocks generative potential. The samples analysed have vitrinite reflectance in the range of 0.84–1.10 %Ro and pyrolysis Tmax in the range of 432–454 °C indicate that the Mukalla source rocks contain mature to late mature organic matter. Good oil-generating potential is anticipated from the coals and coaly shale sediments with high hydrogen indices (250–449 mg HC/g TOC). This is supported by their significant amounts of oil-liptinite macerals are present in these coals and coaly shale sediments and Py-GC (S2) pyrograms with n-alkane/alkene doublets extending beyond nC30. The shales are dominated by Type III kerogen (HI < 200 mg HC/g TOC), and are thus considered to be gas-prone.One-dimensional basin modelling was performed to analysis the hydrocarbon generation and expulsion history of the Mukalla source rocks in the Jiza-Qamar Basin based on the reconstruction of the burial/thermal maturity histories in order to improve our understanding of the of hydrocarbon generation potential of the Mukalla source rocks. Calibration of the model with measured vitrinite reflectance (Ro) and borehole temperature data indicates that the present-day heat flow in the Jiza-Qamar Basin varies from 45.0 mW/m2 to 70.0 mW/m2 and the paleo-heat flow increased from 80 Ma to 25 Ma, reached a peak heat-flow values of approximately 70.0 mW/m2 at 25 Ma and then decreased exponentially from 25 Ma to present-day. The peak paleo-heat flow is explained by the Gulf of Aden and Red Sea Tertiary rifting during Oligocene-Middle Miocene, which has a considerable influence on the thermal maturity of the Mukalla source rocks. The source rocks of the Mukalla Formation are presently in a stage of oil and condensate generation with maturity from 0.50% to 1.10% Ro. Oil generation (0.5% Ro) in the Mukalla source rocks began from about 61 Ma to 54 Ma and the peak hydrocarbon generation (1.0% Ro) occurred approximately from 25 Ma to 20 Ma. The modelled hydrocarbon expulsion evolution suggested that the timing of hydrocarbon expulsion from the Mukalla source rocks began from 15 Ma to present-day.  相似文献   

4.
The Dongpu depression is located in the southern Bohai Bay Basin, North China, and it has abundant oil and gas reserves. There has been no systematic documentation of this depression's temperature field and thermal history. In this article, the present geothermal gradient and heat flow were calculated for 68 wells on the basis of 892 formation-testing data from 523 wells. Moreover, the Cenozoic thermal history was reconstructed using 466 vitrinite reflectance data from 105 wells. The results show that the Dongpu depression is characterized by a medium-temperature field between stable and active tectonic areas, with an average geothermal gradient of 34.8 °C/km and an average heat flow of 66.8 mW/m2. The temperature field in the Dongpu depression is significantly controlled by the Changyuan, Huanghe, and Lanliao basement faults and thin lithosphere thickness. The geothermal gradient twice experienced high peaks. One peak was during the Shahejie 3 Formation depositional period, ranging from 45 °C/km to 48 °C/km, and the second peak was in the middle and late of the Dongying Formation depositional period, ranging from 39 °C/km to 40 °C/km, revealing that the Dongpu depression experienced two strong tectonic rifts during the geothermal gradient high peak periods. The geothermal gradient began to decrease from the Neogene, and the geothermal gradient is 31–34 °C/km at the present day. In addition, these results reveal that source rock thermal evolution is controlled by the paleo temperature field of the Dongying Formation depositional period in the Dongpu depression. This study may provide a geothermal basis for deep oil and gas resource evaluation in the Dongpu depression.  相似文献   

5.
A wide-spread bottom simulating reflector (BSR), interpreted to mark the thermally controlled base of the gas hydrate stability zone, is observed over a close grid of multichannel seismic profiles in the Krishna Godavari Basin of the eastern continental margin of India. The seismic data reveal that gas hydrate occurs in the Krishna Godavari Basin at places where water depths exceed 850 m. The thickness of the gas hydrate stability zone inferred from the BSR ranges up to 250 m. A conductive model was used to determine geothermal gradients and heat flow. Ground truth for the assessment and constraints on the model were provided by downhole measurements obtained during the National Gas Hydrate Program Expedition 01 of India at various sites in the Krishna Godavari Basin. Measured downhole temperature gradients and seafloor-temperatures, sediment thermal conductivities, and seismic velocity are utilized to generate regression functions for these parameters as function of overall water depth. In the first approach the base of gas hydrate stability is predicted from seafloor bathymetry using these regression functions and heat flow and geothermal gradient are calculated. In a second approach the observed BSR depth from the seismic profiles (measured in two-way travel time) is converted into heat flow and geothermal gradient using the same ground-truth data. The geothermal gradient estimated from the BSR varies from 27 to 67°C/km. Corresponding heat flow values range from 24 to 60 mW/m2. The geothermal modeling shows a close match of the predicted base of the gas hydrate stability zone with the observed BSR depths.  相似文献   

6.
The Liwan Sag, with an area of 4 000 km~2, is one of the deepwater sags in the Zhujiang River(Pearl River) Mouth Basin, northern South China Sea. Inspired by the exploration success in oil and gas resources in the deepwater sags worldwide, we conducted the thermal modeling to investigate the tectono-thermal history of the Liwan Sag,which has been widely thought to be important to understand tectonic activities as well as hydrocarbon potential of a basin. Using the multi-stage finite stretching model, the tectonic subsidence history and the thermal history have been obtained for 12 artificial wells, which were constructed on basis of one seismic profile newly acquired in the study area. Two stages of rifting during the time periods of 49–33.9 Ma and 33.9–23 Ma can be recognized from the tectonic subsidence pattern, and there are two phases of heating processes corresponding to the rifting.The reconstructed average basal paleo-heat flow values at the end of the rifting events are ~70.5 and ~94.2 mW/m~2 respectively. Following the heating periods, the study area has undergone a persistent thermal attenuation phase since 23 Ma and the basal heat flow cooled down to ~71.8–82.5 mW/m~2 at present.  相似文献   

7.
The Hikurangi Margin, east of the North Island of New Zealand, is known to contain significant deposits of gas hydrates. This has been demonstrated by several multidisciplinary studies in the area since 2005. These studies indicate that hydrates in the region are primarily located beneath thrust ridges that enable focused fluid flow, and that the hydrates are associated with free gas. In 2009–2010, a seismic dataset consisting of 2766 km of 2D seismic data was collected in the undrilled Pegasus Basin, which has been accumulating sediments since the early Cretaceous. Bottom-simulating reflections (BSRs) are abundant in the data, and they are accompanied by other features that indicate the presence of free gas and concentrated accumulations of gas hydrate. We present results from a detailed qualitative analysis of the data that has made use of automated high-density velocity analysis to highlight features related to the hydrate system in the Pegasus Basin. Two scenarios are presented that constitute contrasting mechanisms for gas-charged fluids to breach the base of the gas hydrate stability zone. The first mechanism is the vertical migration of fluids across layers, where flow pathways do not appear to be influenced by stratigraphic layers or geological structures. The second mechanism is non-vertical fluid migration that follows specific strata that crosscut the BSR. One of the most intriguing features observed is a presumed gas chimney within the regional gas hydrate stability zone that is surrounded by a triangular (in 2D) region of low reflectivity, approximately 8 km wide, interpreted to be the result of acoustic blanking. This chimney structure is cored by a ∼200-m-wide low-velocity zone (interpreted to contain free gas) flanked by high-velocity bands that are 200–400 m wide (interpreted to contain concentrated hydrate deposits).  相似文献   

8.
The Pearl River Mouth Basin (PRMB) and Qiongdongnan Basin (QDNB) are oil and gas bearing basins in the northern margin of the South China Sea (SCS). Geothermal survey is an important tool in petroleum exploration. A large data set comprised of 199 thermal conductivities, 40 radioactive heat productions, 543 measured geothermal gradient values, and 224 heat flow values has been obtained from the two basins. However, the measured geothermal gradient data originated from diverse depth range make spatial comparison a challenging task. Taking into account the variation of conductivity and heat production of rocks, we use a “uniform geothermal gradient” to characterize the geothermal gradient distribution of the PRMB and QDNB. Results show that, in the depth interval of 0–5 km, the “uniform geothermal gradient” in the PRMB varies from 17.8 °C/km to 50.2 °C/km, with an average of 32.1 ± 6.0 °C/km. In comparison, the QDNB has an average “uniform geothermal gradient” of 31.9 ± 5.6 °C/km and a range between 19.7 °C/km and 39.5 °C/km. Heat flows in the PRMB and QDNB are 71.3 ± 13.5 mW/m2 and 72.9 ± 14.2 mW/m2, respectively. The heat flow and geothermal gradient of the PRMB and QDNB tend to increase from the continental shelf to continental slope owing to the lithosphereic/crustal thinning in the Cenozoic.  相似文献   

9.
Reconnaissance seismic reflection data indicate that Canada Basin is a >700,000 sq. km. remnant of the Amerasia Basin of the Arctic Ocean that lies south of the Alpha-Mendeleev Large Igneous Province, which was constructed across the northern part of the Amerasia Basin between about 127 and 89-83.5 Ma. Canada Basin was filled by Early Jurassic to Holocene detritus from the Beaufort-Mackenzie Deltaic System, which drains the northern third of interior North America, with sizable contributions from Alaska and Northwest Canada. The basin contains roughly 5 or 6 million cubic km of sediment. Three fourths or more of this volume generates low amplitude seismic reflections, interpreted to represent hemipelagic deposits, which contain lenses to extensive interbeds of moderate amplitude reflections interpreted to represent unconfined turbidite and amalgamated channel deposits.Extrapolation from Arctic Alaska and Northwest Canada suggests that three fourths of the section in Canada Basin is correlative with stratigraphic sequences in these areas that contain intervals of hydrocarbon source rocks. In addition, worldwide heat flow averages suggest that about two thirds of Canada Basin lies in the oil or gas windows. Structural, stratigraphic and combined structural and stratigraphic features of local to regional occurrence offer exploration targets in Canada Basin, and at least one of these contains bright spots. However, deep water (to almost 4000 m), remoteness from harbors and markets, and thick accumulations of seasonal to permanent sea ice (until its possible removal by global warming later this century) will require the discovery of very large deposits for commercial success in most parts of Canada Basin.  相似文献   

10.
The Yuqi block is an important area for oil and gas exploration in the northern Akekule uplift, Tarim Basin, northwestern China. The Upper Triassic Halahatang Formation (T3h) within the Yuqi block can be subdivided into a lowstand system tract (LST), a transgressive system tract (TST), and a highstand system tract (HST), based on a study of initial and maximum flood surfaces. Oil in the lowstand system tract of the Halahatang Formation is characterized by medium to lightweight (0.8075 g/cm3–0.9258 g/cm3), low sulfur content (0.41%–1.4%), and high paraffin content (9.65%–10.25%). The distribution of oil and gas is principally controlled by low-amplitude anticlines and faults. Based on studies of fluorescence thin sections and homogenization temperatures of fluid inclusions, reservoirs in the T3h were formed in at least two stages of hydrocarbon charge and accumulation. During the first stage (Jurassic–Cretaceous) both the structural traps and hydrocarbon reservoirs were initiated; during the second stage (Cenozoic) the structural traps were finally formed and the reservoirs were structurally modified. The reservoir-forming mechanism involved external hydrocarbon sources (i.e. younger reservoirs with oil and gas sourced from old rocks), two directions (vertical and lateral) of expulsion, and multi-stage accumulation. This model provides a theoretical fundament for future oil and gas exploration in the Tarim Basin and other similar basins in northwestern China.  相似文献   

11.
The petroleum generation and charge history of the northern Dongying Depression, Bohai Bay Basin was investigated using an integrated fluid inclusion analysis workflow and geohistory modelling. One and two-dimensional basin modelling was performed to unravel the oil generation history of the Eocene Shahejie Formation (Es3 and Es4) source rocks based on the reconstruction of the burial, thermal and maturity history. Calibration of the model with thermal maturity and borehole temperature data using a rift basin heat flow model indicates that the upper interval of the Es4 source rocks began to generate oil at around 35 Ma, reached a maturity level of 0.7% Ro at 31–30 Ma and a peak hydrocarbon generation at 24–23 Ma. The lower interval of the Es3 source rocks began to generate oil at around 33–32 Ma and reached a maturity of 0.7% Ro at about 27–26 Ma. Oil generation from the lower Es3 and upper Es4 source rocks occurred in three phases with the first phase from approximately 30–20 Ma; the second phase from approximately 20–5 Ma; and the third phase from 5 Ma to the present day. The first and third phases were the two predominant phases of intense oil generation.Samples from the Es3 and Es4 reservoir intervals in 12 wells at depth intervals between 2677.7 m and 4323.0 m were investigated using an integrated fluid inclusion workflow including petrography, fluorescence spectroscopy and microthermometry to determine the petroleum charge history in the northern Dongying Depression. Abundant oil inclusions with a range of fluorescence colours from near yellow to near blue were observed and were interpreted to represent two episodes of hydrocarbon charge based on the fluid inclusion petrography, fluorescence spectroscopy and microthermometry data. Two episodes of oil charge were determined at 24–20 Ma and 4–3 Ma, respectively with the second episode being the predominant period for the oil accumulation in the northern Dongying Depression. The oil charge occurred during or immediately after the modelled intense oil generation and coincided with a regional uplift and a rapid subsidence, suggesting that the hydrocarbon migration from the already overpressured source rocks may have been triggered by the regional uplift and rapid subsidence. The expelled oil was then charged to the already established traps in the northern Dongying Depression. The proximal locations of the reservoirs to the generative kitchens and the short oil migration distance facilitate the intimate relationship between oil generation, migration and accumulation.  相似文献   

12.
Gas hydrates in the western deep-water Ulleung Basin, East Sea of Korea   总被引：1，自引：0，他引：1  
Geophysical surveys and geological studies of gas hydrates in the western deep-water Ulleung Basin of the East Sea off the east coast of Korea have been carried out by the Korea Institute of Geoscience and Mineral Resources (KIGAM) since 2000. The work included a grid of 4782 km of 2D multi-channel seismic reflection lines and 11 piston cores 5–8 m long. In the piston cores, cracks generally parallel to bedding suggest significant in-situ gas. The cores showed high amounts of total organic carbon (TOC), and from the southern study area showed high residual hydrocarbon gas concentrations. The lack of higher hydrocarbons and the carbon isotope ratios indicate that the methane is primarily biogenic. The seismic data show areas of bottom-simulating reflectors (BSRs) that are associated with gas hydrates and underlying free gas. An important observation is the numerous seismic blanking zones up to 2 km across that probably reflect widespread fluid and gas venting and that are inferred to contain substantial gas hydrate. Some of the important results are: (1) BSRs are widespread, although most have low amplitudes; (2) increased P-wave velocities above some BSRs suggest distributed low to moderate concentration gas hydrate whereas a velocity decrease below the BSR suggests free gas; (3) the blanking zones are often associated with upbowing of sedimentary bedding reflectors in time sections that has been interpreted at least in part due to velocity pull-up produced by high-velocity gas hydrate. High gas hydrate concentrations are also inferred in several examples where high interval velocities are resolved within the blanking zones. Recently, gas hydrate recoveries by the piston coring and deep-drilling in 2007 support the interpretation of substantial gas hydrate in many of these structures.  相似文献   

13.
The Late Miocene Zeit Formation is exposed in the Red Sea Basin of Sudan and represents an important oil-source rock. In this study, five (5) exploratory wells along Red Sea Basin of Sudan are used to model the petroleum generation and expulsion history of the Zeit Formation. Burial/thermal models illustrate that the Red Sea is an extensional rift basin and initially developed during the Late Eocene to Oligocene. Heat flow models show that the present-day heat flow values in the area are between 60 and 109 mW/m2. The variation in values of the heat flow can be linked to the raise in the geothermal gradient from margins of the basin towards offshore basin. The offshore basin is an axial area with thick burial depth, which is the principal heat flow source.The paleo-heat flow values of the basin are approximately from 95 to 260 mW/m2, increased from Oligocene to Early Pliocene and then decreased exponentially prior to Late Pliocene. This high paleo-heat flow had a considerable effect on the source rock maturation and cooking of the organic matter. The maturity history models indicate that the Zeit Formation source rock passed the late oil-window and converted the oil generated to gas during the Late Miocene.The basin models also indicate that the petroleum was expelled from the Zeit source rock during the Late Miocene (>7 Ma) and it continues to present-day, with transformation ratio of more than 50%. Therefore, the Zeit Formation acts as an effective source rock where significant amounts of petroleum are expected to be generated in the Red Sea Basin.  相似文献   

14.
Bottom simulating reflectors (BSRs), known as the base of gas hydrate stability zone, have been recognized and mapped using good quality three-dimensional (3D) pre-stack migration seismic data in Shenhu Area of northern South China Sea. Additionally, seismic attribute technique has been applied to better constrain on the distribution of gas hydrate. The results demonstrate that gas hydrate is characterized by “blank” zone (low amplitude) in instantaneous amplitude attribute. The thickness of gas hydrate stability zone inferred from BSR ranges from 125 to 355 m with an average of 240 m at sea water depth from 950 to 1,600 m in this new gas hydrate province. The volume of gas in-place bound in hydrate is estimated from 1.7 × 109 to 4.8 × 109 m3, with the most likely value of around 3.3 × 109 m3, using Monte Carlo simulation. Furthermore, geothermal gradient and heat flow are derived from the depths of BSRs using a conductive heat transfer model. The geothermal gradient varies from 35 to 95°C km−1 with an average of 54°C km−1. Corresponding heat flow values range from 43 to 105 mW m−2 with an average of 64 mW m−2. By comparison with geological characteristics, we suggest that the distribution of gas hydrate and heat flow are largely associated with gas chimneys and faults, which are extensively distributed in Shenhu Area, providing easy pathways for fluids migrating into the gas hydrate stability zone for the formation of gas hydrate. This study can place useful constraints for modeling gas hydrate stability zone from measured heat flow data and understanding the mechanism of gas hydrate formation in Shenhu Area.  相似文献   

15.
In western Canada gas hydrates have been thought to exist primarily in the Cascadia accretionary prism off southern Vancouver Island, British Columbia (BC). We present evidence for the existence of gas hydrate in folds and ridges of the Winona Basin up to 40 km seaward from the foot of the continental slope off northern Vancouver Island. The occurrence of a bottom-simulating reflector (BSR) observed in a number of vintage seismic reflection profiles is strongly correlated to faulted, and folded sedimentary ridges and buried folds. The observed tectonic structures of the Winona Basin are within the rapidly evolving Juan de Fuca - Cascadia - Queen Charlotte triple junction off BC. Re-processing of multi-channel data imaged mildly to strongly deformed sediments; the BSR is confined to sediments with stronger deformation. Changes in the amplitude character of sediment-reflections above and below the depth of the base of gas hydrate stability zone were also used as an indicator for the presence of gas hydrate. Additionally, regional amplitude and frequency reduction below some strong BSR occurrences may indicate free gas accumulations. Gas hydrate formation in the Winona Basin appears strongly constrained to folds and ridges and thus correlated to deeper-routed fluid-advection regimes. Methane production from in situ microbial activities as a source of gas to form gas hydrates, as proposed to be a major contributor for gas hydrates within the accretionary prism to the south, appears to be insufficient to produce the widespread gas hydrate occurrences in the Winona Basin. Potential reasons for the lack of sufficient in situ gas production may be that sedimentation rates are 5-100 times higher than those in the accretionary prism so that available organic carbon moves too quickly through the gas hydrate stability field. The confinement of BSRs to ridges and folds within the Winona Basin results in an areal extent of gas hydrate occurrences that is a factor of five less than what is expected from regional gas hydrate stability field mapping using water-depth (pressure) as the only controlling factor only.  相似文献   

16.
We use a simple approach to estimate the present-day thermal regime along the northwestern part of the Western Indian Passive Margin, offshore Pakistan. A compilation of bottom borehole temperatures and geothermal gradients derived from new observations of bottom-simulating reflections (BSRs) allows us to constrain the relationship between the thermal regime and the known tectonic and sedimentary framework along this margin. Effects of basin and crustal structure on the estimation of thermal gradients and heat flow are discussed. A hydrate system is located within the sedimentary deep marine setting and compared to other provinces on other continental margins. We calculate the potential radiogenic contribution to the surface heat flow along a profile across the margin. Measurements across the continental shelf show intermediate thermal gradients of 38–44 °C/km. The onshore Indus Basin shows a lower range of values spanning 18–31 °C/km. The Indus Fan slope and continental rise show an increasing gradient from 37 to 55 °C/km, with higher values associated with the thick depocenter. The gradient drops to 33 °C/km along the Somnath Ridge, which is a syn-rift volcanic construct located in a landward position relative to the latest spreading center around the Cretaceous–Paleogene transition.  相似文献   

17.
Measurements of dispersed vitrinite along several exploration wells within the northern Rhinegraben are indicative of a thermal graben history that is influenced by a combination of basal conductive and groundwater-flow related convective heat transfer. To determine the conductive/convective components of heat transfer within the rift today, a series of 2D numerical groundwater flow and heat models are developed along a cross-sectional transect across the northern Rhinegraben. Fault zone permeability is varied in the simulations of these models to determine the possible fluid pathways and the effects of circulating groundwater on the graben temperature field. Depending on the fault permeability, negative thermal anomalies always develop in areas of cold recharging groundwater along the graben flanks regardless of fault permeability, whereas hot discharging groundwater near the topographic low of the graben only results in positive thermal anomalies under the assumption of high fault permeability. Simulation results suggest that the modern groundwater flow system has an overall net cooling effect on the temperature field of the rift.Without convective cooling by groundwater, vitrinite reflectance levels in wells would be expected to be much higher on average than are observed. Although relatively high heat flow densities (100 mW/m2) are documented in the Rhinegraben, an average of only 65 mW/m2 would be sufficient to produce the observed vitrinite reflectance levels. Thus, a long-lived (>10 My) cooling convective fluid flow in combination with a high basal heat flow seems to be active.  相似文献   

18.
Chengdao is an offshore area in the Bohai Bay Basin that contains approximately 25.7 × 108 bbl of oil and gas reserves within the sandstone reservoirs in Neogene strata. However, previous predictions of hydrocarbon accumulation in Neogene traps are inaccurate, resulting in a current failure rate of 50% when drilling for hydrocarbons in this area. To build an improved exploration model for Neogene traps, we select 92 traps from Neogene strata in the Chengdao area to quantify the filling degree, which is an indicator of hydrocarbon accumulation efficiency. The quantified filling degree is based on actual geological and exploration data and differs significantly among various trap types. The filling degree of traps also varies significantly with their structural locations and decreases generally from the northwest to the southeast along the Chengbei Fault zone. Vertically, the filling degree is highly heterogeneous, initially increasing from the bottom to the middle of Neogene strata and then decreasing towards the top of the strata. These Neogene hydrocarbon reservoirs are sourced from the Paleogene, and as they lay vertically away from the source rocks, their hydrocarbon enrichment is constrained largely by hydrocarbon migration distance and vertical migration pathways. The sealing capacity of faults and cap rocks, sandbody orientation and reservoir sedimentary facies determine the maximum column height, which in turn affects the amount of hydrocarbon accumulation within these traps. A scatter plot analysis of individual controls and volumetric filling for each trap type is compiled using multivariate linear regression analysis to quantify controls and the dominant control of hydrocarbon accumulation is determined.  相似文献   

19.
Knowledge of the in situ, or contemporary stress field is vital for planning optimum orientations of deviated and horizontal wells, reservoir characterization and a better understanding of geodynamic processes and their effects on basin evolution.This study provides the first documented analysis of in situ stress and pore pressure fields in the sedimentary formations of the Cuu Long and Nam Con Son Basins, offshore Vietnam, based on data from petroleum exploration and production wells.In the Cuu Long Basin, the maximum horizontal stress is mainly oriented in NNW–SSE to N–S in the northern part and central high. In the Nam Con Son Basin, the maximum horizontal stress is mainly oriented in NE–SW in the northern part and to N–S in the central part of the basin.The magnitude of the vertical stress has a gradient of approximately 22.2 MPa/km at 3500 m depth. Minimum horizontal stress magnitude is approximately 61% of the vertical stress magnitude in normally pressured sequences.The effect of pore pressure change on horizontal stress magnitudes was estimated from pore pressure and fracture tests data in depleted zone caused by fluid production, and an average pore pressure–stress coupling ratio (ΔSh/ΔPp) obtained was 0.66. The minimum horizontal stress magnitude approaches the vertical stress magnitude in overpressured zones of the Nam Con Son Basin, suggesting that an isotropic or strike-slip faulting stress regime may exist in the deeper overpressured sequences.  相似文献   

20.
The Gas Hydrate Research and Development Organization (GHDO) of Korea successfully accomplished both coring (hydraulic piston and pressure coring) and logging (logging-while-drilling, LWD, and wireline logging) to investigate the presence of gas hydrate during the first deep drilling expedition in the Ulleung Basin, East Sea of Korea (referred to as UBGH1) in 2007. The LWD data from two sites (UBGH1-9, UBGH1-10) showed elevated electrical resistivity (>80 Ω-m) and P-wave velocity (>2000 m/s) values indicating the presence of gas hydrate. During the coring period, the richest gas hydrate accumulation was discovered at these intervals. Based on log data, the occurrence of gas hydrate is primarily controlled by the presence of fractures. The gas hydrate saturation calculated using Archie’s relation shows greater than 60% (as high as ∼90%) of the pore space, although Archie’s equation typically overestimates gas hydrate saturation in near-vertical fractures. The saturation of gas hydrate is also estimated using the modified Biot-Gassmann theory (BGTL) by Lee and Collett (2006). The saturation values estimated rom BGTL are much lower than those calculated from Archie’s equation. Based on log data, the hydrate-bearing sediment section is approximately 70 m (UBGH1-9) to 130 m (UBGH1-10) in thickness at these two sites. This was further directly confirmed by the recovery of gas hydrate samples and pore water freshening collected from deep drilling core during the expedition. LWD data also strongly support the interpretation of the seismic gas hydrate indicators (e.g., vent or chimney structures and bottom-simulating reflectors), which imply the probability of widespread gas hydrate presence in the Ulleung Basin.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号