共查询到20条相似文献，搜索用时 31 毫秒
1.
Inelastic seismic response of torsionally unbalanced systems designed using elastic dynamic analysis
This paper evaluates the inelastic seismic response of torsionally unbalanced structural systems with strength distributed using elastic response spectrum analysis. The structural model is a single mass torsionally unbalanced system with lateral load resisting elements spanning in two principal directions. The element strength is distributed based on elastic response spectrum analysis and three different approaches to incorporate accidental torsion are considered: (a) without incorporating accidental torsion; (b) by applying static floor torques; (c) by shifting the location of the centre of mass. The seismic input is bidirectionally applied at the base of the model. It is shown that the inelastic responses depend strongly on the torsional stiffness of the system. For a torsionally stiff system, the torsional response leads to a decrease in the stiff edge displacement; however, for a torsionally flexible system, it tends to increase the stiff edge displacement. Using response spectrum analysis without including accidental torsion may lead to excessive additional ductility demand on the stiff edge element. With accidental torsion effect incorporated, the response spectrum analysis will give a strength distribution such that there will be no excessive additional ductility demands on the lateral load resisting elements. 相似文献
2.
This paper presents the results of an analytical study of the strength distribution of lateral load resisting elements in torsionally unbalanced systems designed based on codified torsional provisions. It is shown that the element strength can be expressed conveniently as the element strength of a similar but torsionally balanced system multiplied by a strength factor. This strength factor depends on three system parameters, namely, the location of the element relative to the centre of rigidity, and the torsional stiffness and eccentricity of the structure. In addition, it depends on the design coefficients of the code specified design eccentricity expressions. The influence of each of these factors on the element strength distribution is discussed. A new set of values for the design coefficients is proposed. By means of examples, it is shown that the proposed torsional provision is an improvement over those suggested in the National Building Code of Canada and the New Zealand code. 相似文献
3.
A large number of parameters affect the inelastic response of an eccentric system. The centre of resistance no longer remains constant due to continuous loading and unloading of various elements of the system in and out of the inelastic region. The objective of this study is to develop the concept of strength eccentricity for asymmetrical structures excited well into the inelastic region in the event of a severe earthquake. A single mass monosymmetric three-element system is selected. The torsional flexibility parameter is varied so as to obtain nine eccentric configurations covering the entire spectrum of such systems. These models were subjected to S00E component of the El Centro earthquake of 1940 which is considered to be a very severe earthquake. The concept of effective strength eccentricity is introduced which is defined as strength eccentricity at the point of intersection of ductility ratio curves of REE and FEE. It is proposed to provide additional strength in the elements of a torsionally unbalanced system independent of the design eccentricity. Empirical equations are proposed to account for design eccentricity and additional strength as well as distribution of the design strength. The proposed formulation is compared with the torsional provisions of UBC 1991, NBCC 1990 and NZC 1992. It is concluded that additional ductility demand on the REE and FEE designed based on the proposed formulation is almost nil as compared to that given by the three codes. The NZC and UBC require maximum ductility on the REE. The increase in overall strength of the system is least for the proposed formulation as compared to that given by the three codes. NBCC consistently requires the maximum total strength ratio. 相似文献
4.
Seismic building codes include design provisions to account for the torsional effects arising in torsionally unbalanced (asymmetric) buildings. These provisions are based on two alternative analytical procedures for determining the design load for the individual resisting structural elements. A previous study has shown that the linear elastic modal analysis procedure may not lead to conservative designs, even for multistorey buildings with regular asymmetry, when such structures are excited well into the inelastic range of response. The equivalent static force procedure as recommended by codes may also be deficient in accounting for additional ductility demand in the critical stiff-edge elements. This paper addresses the non-conservatism of existing static torsional provisions and examines aspects of element strength distribution and its influence on inelastic torsional effects. A recommendation is made for improving the effectiveness of the code-type static force procedure for torsionally unbalanced multistorey frame buildings with regular asymmetry, leading to a design approach which estimates conservatively the peak ductility demand of edge elements on both sides of the building. The modified approach also retains the simplicity of existing code provisions and results in acceptable levels of additional lateral design strength. It has recently been adopted by the new Australian earthquake code, which is due to be implemented early in 1993. 相似文献
5.
The effects of horizontal components of ground motion on the linear response of torsionally stiff and torsionally flexible systems, on soft and firm soil conditions, are examined. A one‐story, two‐way asymmetric structural system is used, subjected to uncorrelated ground motion components along their principal directions. Spectral densities for ground accelerations in firm and soft soils are modeled based on recorded data from large intensity Mexican earthquakes. It is shown that for firm soils, in general, these effects are important in the case of torsionally flexible systems that are stiff under translation, or for torsionally stiff systems that are flexible in translation. The percentage combination rules usually specified in seismic design codes are assessed against the dynamic response. Such combination rules can result in overly conservative design forces or underestimated design forces, particularly for torsionally flexible structures. Given the relative magnitude of the response to each ground motion component, it was found that using different percentage values in the combination rules has no significant effect on improving the estimation of the total response. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
6.
Uneven distribution of seismic demand in asymmetric-plan structures is a critical concern in earthquake-resistant design. Contemporary seismic design strategies that are based on linear elastic response, single load reduction factor, and uniform ductility demand throughout an asymmetric system generally lead to unsatisfactory performance in terms of realized ductilities and nonuniform damage distribution due to strong torsional coupling associated with asymmetric-plan systems. In many cases, actual nonlinear behavior of the structure displays significant deviation from what is estimated by a linear elastic, force-based seismic design approach. This study investigates the prediction of seismic demand distribution among structural members of a single-story, torsionally stiff asymmetric-plan system. The focus is on the effect of inherent unbalanced overstrength, resulting from current force-based design practices, on the seismic response of code-designed single-story asymmetric structures. The results obtained are utilized to compile unsymmetrical response spectra and uniform ductility spectra, which are proposed as assessment and preliminary design tools for estimating the seismic performance of multistory asymmetric structures. A simple design strategy is further suggested for improving the inelastic torsional performance of asymmetric systems. Providing additional strength to stiff edge members over their nominal design strength demands leads to a more balanced ductility distribution. Finally, seismic responses of several asymmetric case study structures designed with the aid of the proposed strategy are assessed for validating their improved performance. 相似文献
7.
Recently, a design modification has been proposed for eccentric, torsionally stiff, braced steel buildings, designed according to the current Eurocodes 3 and 8, that improves noticeably their inelastic response under the action of design level earthquakes. The improvement consists in a more uniform distribution of ductility demands throughout the building. In the present paper, a similar, though differently derived, modification is applied to torsionally flexible eccentric buildings and their response is again evaluated under pairs of design earthquake motions. A substantial improvement of their inelastic response is also observed, similar to what had been obtained for torsionally stiff buildings. The new approach is also tested with torsionally stiff buildings and leads to similarly satisfactory results. Thus it may be recommended for general application. 相似文献
8.
Static torsional provisions in most seismic codes require that the lateral force at each floor level be applied at some distance from the reference centre at that floor. However, codes do not specify how to determine the locations of these centres. As a result, several different definitions of the reference centres are being used to implement the code analysis. This investigation examined how the results using various reference centres differ and which of these centres would lead to results that are in agreement with those of dynamic analysis. For this purpose three different buildings ranging form torsionally stiff to torsionally flexible were analysed. It was shown that for the class of buildings studied in this investigation that although the locations of the reference centres were quite different, the results were very similar and nearly independent of the reference centre. Comparison of results calculated from static code equivalent lateral force procedures and results from dynamic response spectrum analyses showed that the static code procedures led to design forces very close (flexible wall) or slightly conservative (stiff wall) when compared to the dynamic analysis for the torsionally stiff building. However, the static code procedures significantly underestimated the design forces of the stiff walls and significantly overestimated the design forces of the flexible walls for the torsionally flexible buildings. © 1998 John Wiley & Sons, Ltd. 相似文献
9.
The paper investigates the influence of design procedures on the seismic response of multi-storey asymmetric buildings. To
this end, some structures are designed according to methods based on either static or modal analysis, with or without design
eccentricities. The seismic response of these systems is determined by means of inelastic dynamic analyses and the design
is thoroughly examined in order to explain the results of the dynamic analyses. Attention is basically focused on the ability
of design methods to prevent asymmetric buildings from experiencing ductility demands much larger than those of the corresponding
torsionally balanced systems. Numerical analyses underline that while design procedures based on either static or modal analysis
are suitable for the design of torsionally rigid structures only those based on modal analysis lead to the satisfactory performance
of torsionally flexible buildings. Furthermore, the study highlights the qualities of a design method proposed by the Authors.
Its application does not require any explicit calculation of design eccentricities and leads to proper seismic response of
both torsionally rigid and flexible asymmetric buildings. 相似文献
10.
The inelastic behaviour of eccentric single-storey building structures subjected to sinusoidal ground excitation is examined. The Kryloff-Bogoliuboff method is employed to provide approximate solutions in the amplitude-frequency domain. Structural resisting elements are assumed to exhibit bilinear hysteretic behaviour and coupled response is investigated in terms of both system response as well as individual element ductility requirements. In addition to demonstrating the well-known softening property inherent in yielding systems, the importance of the principal parameters governing coupled response is evaluated in a consistent parametric fashion. Within the context of earthquake resistant building design, the results indicate the absence of amplified response when torsional and translational frequencies are close, in contrast to the much emphasized observation of internal resonance for linear elastic structures. Equally important, structural elements located on the stiff edge of eccentric buildings are found to be only marginally affected by the magnitude of the eccentricity, thus indicating that seismic building codes which reduce design requirements for these elements underestimate actual behaviour substantially. 相似文献
11.
The static design requirements of some seismic codes, such as the Eurocode 8 and—in most cases—the Uniform Building Code, to allow for the effects of earthquake excitation acting in a direction other than the principal axes of the structure do not apply to one-way asymmetric systems. Therefore, with some exceptions, no specific provisions are considered for such systems to cover effects of structural asymmetry on the behaviour of elements located along the symmetric system direction. Aimed towards fulfilling this need, in this paper, a wide parametric study of the inelastic response of one-way asymmetric systems designed according to Uniform Building Code is carried out, considering two-component earthquake excitations. The analyses show that the maximum ductility demands on elements aligned along the asymmetric system direction are very close to, and even lower than, those obtained for symmetric reference systems. Conversely, the symmetric direction elements undergo significantly larger inelasticity than if they were located in symmetric reference systems. Subsequently, the overstrength needed by the symmetric direction elements to prevent such additional ductility demands for several stiffness and plan configurations is quantified. It is concluded that one-way asymmetry should be considered by seismic codes as an intrinsic system property, thus implying that specific provisions should be included for designing elements located along the symmetric system direction, in addition to those currently subscribed to design the asymmetric direction elements. © 1998 John Wiley & Sons, Ltd. 相似文献
12.
This paper develops an optimized procedure for the design of torsionally unbalanced structures subjected to earthquake loading, considering both the serviceability and the ultimate limit states. An optimal design eccentricity expression, in the form of design charts, and an optimal overstrength factor equation, are proposed. Results show that the recommended design procedure can result in nearly equal performance of both the rigid edge and the flexible edge elements. For a wide combination of primary system parameters, the responses of both edge elements are consistently lower than, or in the neighbourhood of, the response of the corresponding torsionally balanced reference model. The proposed procedure retains simplicity and can be easily implemented (with certain limitations) in design practice. It also has the added advantages of requiring the structure to be analysed only once for each limit state in each principal direction (as opposed to twice, in existing code torsional provisions), and results in a significantly lower overstrength factor, compared with the overstrength factors corresponding to the torsional provisions of seismic codes in the United States and Canada. The proposed procedure is also applicable to torsionally unbalanced structures with and without transverse resisting elements. © 1997 John Wiley & Sons, Ltd. 相似文献
13.
An Erratum has been published for this article in Earthquake Engng. Struct. Dyn. 2004; 33:1429. Based on structural dynamics theory, the modal pushover analysis (MPA) procedure retains the conceptual simplicity of current procedures with invariant force distribution, now common in structural engineering practice. The MPA procedure for estimating seismic demands is extended to unsymmetric‐plan buildings. In the MPA procedure, the seismic demand due to individual terms in the modal expansion of the effective earthquake forces is determined by non‐linear static analysis using the inertia force distribution for each mode, which for unsymmetric buildings includes two lateral forces and torque at each floor level. These ‘modal’ demands due to the first few terms of the modal expansion are then combined by the CQC rule to obtain an estimate of the total seismic demand for inelastic systems. When applied to elastic systems, the MPA procedure is equivalent to standard response spectrum analysis (RSA). The MPA estimates of seismic demand for torsionally‐stiff and torsionally‐flexible unsymmetric systems are shown to be similarly accurate as they are for the symmetric building; however, the results deteriorate for a torsionally‐similarly‐stiff unsymmetric‐plan system and the ground motion considered because (a) elastic modes are strongly coupled, and (b) roof displacement is underestimated by the CQC modal combination rule (which would also limit accuracy of RSA for linearly elastic systems). Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
14.
Using a single mass monosymmetric model, this paper examines the additional seismic inelastic deformations and displacement caused by structural asymmetry of the model. Stiffness eccentricity and resistance eccentricity are used as measures of asymmetry in the elastic and inelastic range respectively. Seven ways of specifying strength distribution among resisting elements are considered, including code provisions from Canada, Mexico, New Zealand and the United States. These specifications are related t o the model resistance eccentricity. It is shown that when torsional shears are included in the strength design of the elements, the structure in general will have small resistance eccentricity, even if it has large stiffness eccentricity in the elastic range. For structures which are designed with allowance for torsional shears, the ductility demands on the elements are similar to those when the structure is symmetrical. However, the edge displacements can be up to three times that if the system is symmetrical. This finding has significant implications in evaluating adequate separation between buildings to avoid the pounding problem during earthquakes. 相似文献
15.
T. Paulay 《地震工程与结构动力学》1998,27(10):1101-1121
It is postulated that in order to estimate torsional effects on the seismic response of ductile building structures, the associated plastic mechanism to be developed in the three-dimensional system should be identified. The proposed approach is very different from that embodied in building codes. Inelastic structures are classified as either torsionally unrestrained or restrained. It is shown that clearly defined mechanisms that are to be mobilized, enable the acceptable system ductility demand to be estimated. This should ensure that the corresponding demands imposed on critical translatory elements of the system do not exceed their established displacement ductility capacity. To this end familiar quantities, such as element yield displacement and stiffness, are redefined. Comparisons are made of the intents of existing codified design approaches and those emphasising the role of imposed inelastic displacements. A simple treatment of the consequences of earthquake-induced inelastic skew displacements is also addressed. The primary aim of the paper is to offer very simple concepts, based on easily identifiable plastic mechanisms, to be utilized in structural design rather than advancement in analyses. Detailed design applications of these concepts are described elsewhere. The approach is an extension of the deterministic philosophy of capacity design, now used in some countries. © 1998 John Wiley & Sons, Ltd. 相似文献
16.
This paper investigates the effects of supplemental viscous damping on the seismic response of one‐storey, asymmetric‐plan systems responding in the inelastic range of behaviour. It was found that addition of the supplemental damping reduces not only deformation demand but also ductility and hysteretic energy dissipation demands on lateral load resisting elements during earthquake loading. However, the level of reduction strongly depends on the plan‐wise distribution of supplemental damping. Nearly optimal reduction in demands on the outermost flexible‐side element, an element generally considered to be the most critical element, was realized when damping was distributed unevenly in the system plan such that the damping eccentricity was equal in magnitude but opposite in algebraic sign to the structural eccentricity of the system. These results are similar to those noted previously for linear elastic systems, indicating that supplemental damping is also effective for systems expected to respond in the inelastic range. Copyright © 2001 John Wiley & Sons, Ltd. 相似文献
17.
The accurate evaluation of code torsional provisions for plan-eccentric structures exhibiting inelastic response relies on the adoption of appropriate systems defining both the torsionally balanced (reference) and torsionally unbalanced cases. Whilst a considerable number of analytical studies of this problem have been presented in the literature, inconsistencies have arisen in their conclusions. It is evident from a review of previous studies that one factor contributing significantly to these discrepancies arises in the definition of the structural layout. An issue of particular importance is whether the transverse load-resisting elements oriented perpendicular to the assumed (lateral) direction of earthquake loading should, for purposes of realism, be included in model definitions. Given the diverse approaches in the existing literature, clarification of this issue is required in order to advance the understanding of inelastic torsional response behaviour and to assist the interpretation and comparison of previous studies. This paper aims to provide such clarification, based on analyses of a series of models defined rigorously according to code design provisions. Such models have been subjected to both uni- and bi-directional ground motion input. It is concluded that for the flexible-edge element, accurate estimates of additional ductility demand arising from torsional effects may be obtained from uni-directional models (in which both the transverse elements and the corresponding earthquake component are neglected) only for medium-period to long-period systems. Such estimates may be over-conservative for short-period systems, which constitute a large proportion of systems for which code static torsional provisions are utilized. It is further concluded that models incorporating the transverse elements but analysed under uni-directional lateral loading may underestimate by up to 100% the torsional effects in such systems, but are reasonably accurate for medium- and long-period structures. 相似文献
18.
The study of the torsional response of buildings in the inelastic range of behaviour is of great interest since the ability of structures to resist strong earthquakes mainly relies on their ductility and capacity for energy dissipation. Furthermore, an examination of the performance of structures during past earthquakes demonstrates that plan-asymmetric buildings suffered greater damage due to torsional response. The paper deals with this subject by analysing a model which idealizes a one-storey building with resisting elements oriented along two perpendicular directions. In addition to the parameters of the elastic behaviour, the inelastic system response depends on full yield capacity and plan-wise strength distribution. The influence of the criterion adopted for the design of resisting elements on local ductility demand and damage has been evaluated by parametric analysis. In particular, a comparison has been carried out between systems with equal design levels for all elements and systems with design levels dependent on the element location. For a given elastic behaviour and total capacity, the strength distributions in plan have been defined which minimize ductility demand and structural damage. Finally, based on these findings, responses from models designed according to several seismic codes have been compared. 相似文献
19.
Mario de Stefano Edoardo Michele Marino Pier Paolo Rossi 《Bulletin of Earthquake Engineering》2006,4(1):23-42
In past years, seismic response of asymmetric structures has been frequently analysed by means of single-storey models, because
of their simplicity and low computational cost. However, it is widely believed that use of more realistic multi-storey models
is needed in order to investigate effects of some system characteristics (such as overstrength, higher modes of vibration,
etc.) that make behaviour of multi-storey schemes different from that of single-storey systems. This paper examines effects
of the overstrength in element cross-sections on the seismic behaviour of multi-storey asymmetric buildings. It is shown that
in actual buildings this characteristic, which is sometimes very variable both in plan and along the height of the building,
may lead to distributions of ductility demands different from those expected according to the results from single-storey models.
Consequently, torsional provisions, which aim at reducing ductility demands of single-storey asymmetric systems to those of
the corresponding torsionally balanced systems, should be re-checked in light of the behaviour of realistic multi-storey buildings. 相似文献
20.
This paper aims to extend the consecutive modal pushover (CMP) procedure for estimating the seismic demands of two-way unsymmetric-plan tall buildings subjected to bi-directional seismic ground motions taking the effects of higher modes and torsion into account. Multi-stage and single-stage pushover analyses are carried out in both X and Y directions. Inelastic seismic responses obtained by multi-stage and single-stage pushover analyses for X and Y directions are combined using the SRSS combination scheme. The final seismic responses are determined by enveloping the combined results of multi-stage and single-stage pushover analyses. To evaluate the accuracy of the proposed procedure, it is applied to two-way unsymmetric-plan tall buildings which include torsionally stiff and torsionally flexible systems. The results derived from the CMP procedure are compared with those from nonlinear response history analysis (NL-RHA), as a benchmark solution. Moreover, the advantages of the proposed procedure are demonstrated by comparing the results derived from the CMP to those from pushover analysis with uniform and fundamental effective mode distributions. The proposed procedure is able to accurately predict amplification or de-amplification of the seismic displacements at the flexible and stiff edges of the two-way unsymmetric-plan tall buildings by considering the effects of higher modes and torsion. The extended CMP procedure can accurately estimate the peak inelastic responses, such as displacements and storey drifts. The CMP procedure features a higher potential in estimating plastic hinge rotations at both flexible and stiff sides of unsymmetric-plan tall buildings under bi-directional seismic excitation when compared to the uniform and fundamental effective mode force distributions. 相似文献