共查询到20条相似文献，搜索用时 31 毫秒
1.
In hydraulic fracturing treatments, locating not only hydraulic fractures but also any pre‐existing natural fractures and faults in a subsurface reservoir is very important. Hydraulic fractures can be tracked by locating microseismic events, but to identify the locations of natural fractures, an additional technique is required. In this paper, we present a method to image pre‐existing fractures and faults near a borehole with virtual reverse vertical seismic profiling data or virtual single‐well profiling data (limited to seismic reflection data) created from microseismic monitoring using seismic interferometry. The virtual source data contain reflections from natural fractures and faults, and these features can be imaged by applying migration to the virtual source data. However, the imaging zone of fractures in the proposed method is strongly dependent on the geographic extent of the microseismic events and the location and direction of the fracture. To verify our method, we produced virtual reverse vertical seismic profiling and single‐well profiling data from synthetic microseismic data and compared them with data from real sources in the same relative position as the virtual sources. The results show that the reflection travel times from the fractures in the virtual source data agree well with travel times in the real‐source data. By applying pre‐stack depth migration to the virtual source data, images of the natural fractures were obtained with accurate locations. However, the migrated section of the single‐well profiling data with both real and virtual sources contained spurious fracture images on the opposite side of the borehole. In the case of virtual single‐well profiling data, we could produce correct migration images of fractures by adopting directional redatuming for which the occurrence region of microseismic events is divided into several subdivisions, and fractures located only on the opposite side of the borehole are imaged for each subdivision. 相似文献
2.
Flavio Poletto Lorenzo Petronio Biancamaria Farina Andrea Schleifer 《Geophysical Prospecting》2011,59(3):464-476
We present the results of a seismic interferometry experiment in a shallow cased borehole. The experiment is an initial study for subsequent borehole seismic surveys in an instrumented well site, where we plan to test other surface/borehole seismic techniques. The purpose of this application is to improve the knowledge of the reflectivity sequence and to verify the potential of the seismic interferometry approach to retrieve high‐frequency signals in the single well geometry, overcoming the loss and attenuation effects introduced by the overburden. We used a walkaway vertical seismic profile (VSP) geometry with a seismic vibrator to generate polarized vertical and horizontal components along a surface seismic line and an array of 3C geophones cemented outside the casing. The recorded traces are processed to obtain virtual sources in the borehole and to simulate single‐well gathers with a variable source‐receiver offset in the vertical array. We compare the results obtained by processing the field data with synthetic signals calculated by numerical simulation and analyse the signal bandwidth and amplitude versus offset to evaluate near‐field effects in the virtual signals. The application provides direct and reflected signals with improved bandwidth after vibrator signal deconvolution. Clear reflections are detected in the virtual seismic sections in agreement with the geology and other surface and borehole seismic data recorded with conventional seismic exploration techniques. 相似文献
3.
按照井间地震的观测系统,用改进的突变点加插值射线追踪方法,追踪每炮每道的射线路径,计算几种主要类型的波沿射线路径的波至时间和射线振幅,制作井间地震多炮多道水平分量和垂直分量的合成记录.并将合成记录选排为井间共炮点道集、共接收点道集、共偏移距道集和共中心深度点道集,系统地分析了不同道集内几种主要类型的地震波的传播特征.对野外观测的实际井间地震记录进行了模拟,从复杂的井间地震记录中,识别出井间地震实际观测到的不同类型的波场,为随后的井间地震资料处理和应用提供了依据. 相似文献
4.
5.
Topography and severe variations of near‐surface layers lead to travel‐time perturbations for the events in seismic exploration. Usually, these perturbations could be estimated and eliminated by refraction technology. The virtual refraction method is a relatively new technique for retrieval of refraction information from seismic records contaminated by noise. Based on the virtual refraction, this paper proposes super‐virtual refraction interferometry by cross‐correlation to retrieve refraction wavefields by summing the cross‐correlation of raw refraction wavefields and virtual refraction wavefields over all receivers located outside the retrieved source and receiver pair. This method can enhance refraction signal gradually as the source–receiver offset decreases. For further enhancement of refracted waves, a scheme of hybrid virtual refraction wavefields is applied by stacking of correlation‐type and convolution‐type super‐virtual refractions. Our new method does not need any information about the near‐surface velocity model, which can solve the problem of directly unmeasured virtual refraction energy from the virtual source at the surface, and extend the acquisition aperture to its maximum extent in raw seismic records. It can also reduce random noise influence in raw seismic records effectively and improve refracted waves’ signal‐to‐noise ratio by a factor proportional to the square root of the number of receivers positioned at stationary‐phase points, based on the improvement of virtual refraction's signal‐to‐noise ratio. Using results from synthetic and field data, we show that our new method is effective to retrieve refraction information from raw seismic records and improve the accuracy of first‐arrival picks. 相似文献
6.
A modified reverse-time migration algorithm for offset vertical seismic profiling data is proposed. This algorithm performs depth imaging of target areas in the borehole vicinity without taking into account the overburden. Originally recorded seismograms are used; reliable results can be obtained using only the velocity profile obtained along the well. The downgoing wavefield emitted from a surface source is approximated in the target area using the transmitted P-wave, recorded by the receivers deployed in the well. This is achieved through a reverse-time extrapolation of the direct transmitted P-wave into the target area after its separation in offset vertical seismic profiling seismograms generated using a finite-difference scheme for the solution of the scalar wave equation.
The proposed approach produces 'kinematically' reliable images from reflected PP- and PS-waves and, furthermore, can be applied as a salt proximity tool for salt body flank imaging based on the transmitted PS-waves. Our experiments on synthetic data demonstrate that the modified reverse-time migration provides reliable depth images based on offset vertical seismic profiling data even if only the velocity profile obtained along the borehole is used. 相似文献
The proposed approach produces 'kinematically' reliable images from reflected PP- and PS-waves and, furthermore, can be applied as a salt proximity tool for salt body flank imaging based on the transmitted PS-waves. Our experiments on synthetic data demonstrate that the modified reverse-time migration provides reliable depth images based on offset vertical seismic profiling data even if only the velocity profile obtained along the borehole is used. 相似文献
7.
Flavio Poletto Biancamaria Farina Gualtiero Böhm Kees Wapenaar 《Geophysical Prospecting》2015,63(3):567-586
We present a modified interferometry method based on local tangent‐phase analysis, which corrects the cross‐correlated data before summation. The approach makes it possible to synthesize virtual signals usually vanishing in the conventional seismic interferometry summation. For a given pair of receivers and a set of different source positions, a plurality of virtual traces is obtained at new stationary projected points located along the signal wavefronts passing through the real reference receiver. The position of the projected points is estimated by minimizing travel times using wavefront constraint and correlation‐signal tangent information. The method uses mixed processing, which is partially based on velocity‐model knowledge and on data‐based blind interferometry. The approach can be used for selected events, including reflections with different stationary conditions and projected points with respect to those of the direct arrivals, to extend the interferometry representation in seismic exploration data where conventional illumination coverage is not sufficient to obtain the stationary‐phase condition. We discuss possible applications in crosswell geometry with a velocity anomaly and a time lapse. 相似文献
8.
A two-dimensional walkaway vertical seismic profiling survey using distributed acoustic sensing was conducted at an onshore site in Japan. The maximum depth and the deviation of the observation well were more than 4,000 m and 81 degrees, respectively. Among the several methods for installing fibre optic cables, we adopted the inside coiled tubing method, in which coiled tubing containing a fibre optic cable is deployed. The signal-to-noise ratio of the raw shot gather was low, possibly due to poor coupling between the fibre optic cable and the subsurface formation resulting from the fibre optic cable deployment method and the existence of considerable tubewave noise. Nevertheless, direct P-wave arrivals, P–P reflections and P–S converted waves exhibited acceptable signal-to-noise ratios after careful optimization of gauge length for distributed acoustic sensing optical processing and the application of carefully parameterized tubewave noise suppression. One of the challenges in current distributed acoustic sensing vertical seismic profile data processing is the separation of P- and S-waves using only one-component measurements. Hence, we applied moveout correction using two-dimensional ray tracing. This process effectively highlights only reflected P-waves, which are used in subsequent subsurface imaging. Comparison with synthetic well seismograms and two-dimensional surface seismic data confirms that the final imaging result has a sufficiently high quality for subsurface monitoring. We acquired distributed acoustic sensing vertical seismic profile data under both flowing conditions and closed conditions, in which the well was shut off and no fluid flow was allowed. The two imaging results are comparable and suggest the possibility of subsurface imaging and time-lapse monitoring using data acquired under flowing conditions. The results of this study suggest that, by adopting the inside coiled tubing method without drilling a new observation well, more affordable distributed acoustic sensing vertical seismic profile monitoring can be achieved in fields such as CO2 capture and storage and unconventional shale projects, where monitoring costs have to be minimized. 相似文献
9.
10.
Vertical seismic profiling using a daisy‐chained deployment of fibre‐optic cables in four wells simultaneously – Case study at the Ketzin carbon dioxide storage site 
下载免费PDF全文
下载免费PDF全文 The geological storage of carbon dioxide is considered as one of the measures to reduce greenhouse gas emissions and to mitigate global warming. Operators of storage sites are required to demonstrate safe containment and stable behaviour of the storage complex that is achieved by geophysical and geochemical monitoring, combined with reservoir simulations. For site characterization, as well as for imaging the carbon dioxide plume in the reservoir complex and detecting potential leakage, surface and surface‐borehole time‐lapse seismic monitoring surveys are the most widespread and established tools. At the Ketzin pilot site for carbon dioxide storage, permanently installed fibre‐optic cables, initially deployed for distributed temperature sensing, were used as seismic receiver arrays, demonstrating their ability to provide high‐resolution images of the storage formation. A vertical seismic profiling experiment was acquired using 23 source point locations and the daisy‐chained deployment of a fibre‐optic cable in four wells as a receiver array. The data were used to generate a 3D vertical seismic profiling cube, complementing the large‐scale 3D surface seismic measurements by a high resolution image of the reservoir close to the injection well. Stacking long vibro‐sweeps at each source location resulted in vertical seismic profiling shot gathers characterized by a signal‐to‐noise ratio similar to gathers acquired using geophones. A detailed data analysis shows strong dependency of data quality on borehole conditions with significantly better signal‐to‐noise ratio in regions with good coupling conditions. 相似文献
11.
12.
We present a simple method for estimating an effective source wavelet from the first arrival in marine vertical seismic profiling (VSP) data. The method, which utilizes the free-space Green's function of the Helmholz equation, is simple and very computer efficient. We show examples from synthetic and real offset and walkaway VSP data. In the synthetic examples, we show that data modelled with the estimated wavelet give small residuals when subtracted from the reference data. In the real data examples, we show that when modelling with the wavelet estimated from the real data, in a smooth macromodel, we obtain a good fit between the first arrivals in the real and modelled data. 相似文献
13.
介绍了井间地震数据采集方面取得的最新进展．为了使我国井间地震技术实用化,开展了大井间距井间地震数据采集试验．通过地面浅井激发深井接收、深井激发深井接收、不同炸药量、不同传播距离试验,确定了井间地震观测参数．应用改进后的井中安全炸药震源、一个三分量井中检波器和常规数据记录系统,在陕北顺宁油田的顺3井、顺4井和顺5井3口生产井中成功采集到两对大井间距、深井、油井中的井间地震资料,两对井的井距分别为307．92m和470．36m,采集井段为904．31-1272．32m．共设计了4种观测方式,采集到800多炮井间地震记录,对油井无损害．改进型井中安全炸药震源在使用效率和寿命方面有显著提高,可用于商业性并间地震数据采集． 相似文献
14.
Estimation of Thomsen＇s anisotropic parameters is very important for accuratetime-to-depth conversion and depth migration data processing. Compared with othermethods, it is much easier and more reliable to estimate anisotropic parameters that arerequired for surface seismic depth imaging from vertical seismic profile （VSP） data, becausethe first arrivals of VSP data can be picked with much higher accuracy. In this study, wedeveloped a method for estimating Thomsen＇s P-wave anisotropic parameters in VTImedia using the first arrivals from walkaway VSP data. Model first-arrival travel times arecalculated on the basis of the near-offset normal moveout correction velocity in VTI mediaand ray tracing using Thomsen＇s P-wave velocity approximation. Then, the anisotropicparameters 0 and e are determined by minimizing the difference between the calculatedand observed travel times for the near and far offsets. Numerical forward modeling, usingthe proposed method indicates that errors between the estimated and measured anisotropicparameters are small. Using field data from an eight-azimuth walkaway VSP in TarimBasin, we estimated the parameters 0 and e and built an anisotropic depth-velocity modelfor prestack depth migration processing of surface 3D seismic data. The results showimprovement in imaging the carbonate reservoirs and minimizing the depth errors of thegeological targets. 相似文献
15.
井间地震资料分辨率很高,但是缺乏成熟的解释方法,本文针对井间地震资料的特点,借鉴地面地震解释技术对井间地震资料开展了精细解释方法研究.首先在深度域资料特点分析的基础上,利用区域速度和层析成像速度将深度域井间地震资料转换到时间域进行研究,并通过粗化降频建立起井间地震资料与地面地震资料之间的相似性联系,得到对井间地震低频反射特征的认识,结合井旁道合成地震记录标定建立起井间地震资料的反射特征,准确的解释了井间地震的反射层位.采用地震瞬时属性分析和时频属性分析得到了对沉积环境的认识,进一步通过波阻抗反演更好的认识井间储层特征.在实际应用中综合多种方法进行解释,并结合测井资料对比落实了井间砂体展布特征,得到对井间储层的精细描述结果,解决了两口井之间储层分布范围、横向连通性及厚度变化等问题,取得了较好的应用效果. 相似文献
16.
We develop the true‐amplitude prestack migration of multicomponent data based on the use of elastic Gaussian beams for walkaway vertical seismic profile (VSP) acquisition systems. It consists in a weighted summation of multishot data with specific weights, computed by tracing elastic Gaussian beams from each imaging point of the target area towards the sources and receivers. Each pair of beams may be connected with either a pair of P‐rays (PP‐image) or the P‐ray towards sources and the S‐ray to receivers (PS‐image) and is uniquely determined by dip (the angle of the bisector between the rays and the vertical direction) and opening (the angle between the rays) angles. Shooting from the bottom towards the acquisition system helps to avoid well‐known troubles, in particular multipathing for the imaging conditions in complex velocity models. The ability to fix the dip angle and implement summation over opening angles leads to the so‐called selective images that contain mostly interfaces with desired slopes. On the other hand, a set of images computed for a range of opening angles by summation over all available dip angles is used as input of an AVO‐like inversion procedure for the recovery of elastic parameters. The feasibility of this imaging procedure is verified by synthetic data for 2D realistic elastic models. 相似文献
17.
在井间地震初至走时层析成像中,随着相邻地质体速度差的增大,使得射线分布不均匀,以及网格剖分不合适,导致层析成像结果不理想.物理和数值模型的井间走时层析成像表明：当速度差超过300%时,层析结果畸变较大;在300%～150%之间时,层析结果较好;低于150%时,层析结果好.在此基础上,提出了井间多尺度初至走时层析成像方法,即对同一模型采用多种网格剖分来同时进行层析成像,以获得研究区域的速度图像.数学和物理模型的井间多尺度走时层析结果表明：该方法很好地兼顾了层析成像的分辨率和精度,极大地改善了井间地震层析成像的质量.即使速度差超过30%,其多尺度的层析结果仍然较好.因此,这种方法具有实际应用的潜力. 相似文献
18.
为了研究松南地区陆相砂泥岩薄互层储层岩石物性横向变化、微构造等对油气聚集的影响和探索利用高分辨率井间地震技术直接指示油气分布的可能性,开展了井间地震及地面小三维地震、VSP、测井等立体地震观测．使用了自行研制的井中炸药震源和常规地震记录仪器．采用层析成像方法、反射资料叠前偏移成像方法等对采集到的资料进行研究,得到了不同分辨率的地下构造和岩石物性信息,展示出不同方法技术在分辨薄储层能力上的差异．高分辨率的井间地震成果较好地实现了井间地层对比,查清了两井间储层横向变化和油气分布情况．层析速度与构造信息等的综合应用解释了两井油气产能差异的原因,建立了油气地质模型．所得成果显示出井间地震技术在油气开发中的潜力． 相似文献
19.
Analysis of time‐lapse travel‐time and amplitude changes to assess reservoir compartmentalization 下载免费PDF全文
下载免费PDF全文 Fluid depletion within a compacting reservoir can lead to significant stress and strain changes and potentially severe geomechanical issues, both inside and outside the reservoir. We extend previous research of time‐lapse seismic interpretation by incorporating synthetic near‐offset and full‐offset common‐midpoint reflection data using anisotropic ray tracing to investigate uncertainties in time‐lapse seismic observations. The time‐lapse seismic simulations use dynamic elasticity models built from hydro‐geomechanical simulation output and a stress‐dependent rock physics model. The reservoir model is a conceptual two‐fault graben reservoir, where we allow the fault fluid‐flow transmissibility to vary from high to low to simulate non‐compartmentalized and compartmentalized reservoirs, respectively. The results indicate time‐lapse seismic amplitude changes and travel‐time shifts can be used to qualitatively identify reservoir compartmentalization. Due to the high repeatability and good quality of the time‐lapse synthetic dataset, the estimated travel‐time shifts and amplitude changes for near‐offset data match the true model subsurface changes with minimal errors. A 1D velocity–strain relation was used to estimate the vertical velocity change for the reservoir bottom interface by applying zero‐offset time shifts from both the near‐offset and full‐offset measurements. For near‐offset data, the estimated P‐wave velocity changes were within 10% of the true value. However, for full‐offset data, time‐lapse attributes are quantitatively reliable using standard time‐lapse seismic methods when an updated velocity model is used rather than the baseline model. 相似文献
20.
Retrieving virtual reflection responses at drill‐bit positions using seismic interferometry with drill‐bit noise 下载免费PDF全文
下载免费PDF全文 In the field of seismic interferometry, researchers have retrieved surface waves and body waves by cross‐correlating recordings of uncorrelated noise sources to extract useful subsurface information. The retrieved wavefields in most applications are between receivers. When the positions of the noise sources are known, inter‐source interferometry can be applied to retrieve the wavefields between sources, thus turning sources into virtual receivers. Previous applications of this form of interferometry assume impulsive point sources or transient sources with similar signatures. We investigate the requirements of applying inter‐source seismic interferometry using non‐transient noise sources with known positions to retrieve reflection responses at those positions and show the results using synthetic drilling noise as source. We show that, if pilot signals (estimates of the drill‐bit signals) are not available, it is required that the drill‐bit signals are the same and that the phases of the virtual reflections at drill‐bit positions can be retrieved by deconvolution interferometry or by cross‐coherence interferometry. Further, for this case, classic interferometry by cross‐correlation can be used if the source power spectrum can be estimated. If pilot signals are available, virtual reflection responses can be obtained by first using standard seismic‐while‐drilling processing techniques such as pilot cross‐correlation and pilot deconvolution to remove the drill‐bit signatures in the data and then applying cross‐correlation interferometry. Therefore, provided that pilot signals are reliable, drill‐bit data can be redatumed from surface to borehole depths using this inter‐source interferometry approach without any velocity information of the medium, and we show that a well‐positioned image below the borehole can be obtained using interferometrically redatumed reflection responses with just a simple velocity model. We discuss some of the practical hurdles that restrict the application of the proposed method offshore. 相似文献