共查询到20条相似文献，搜索用时 656 毫秒
1.
2.
The results of an experimental study aimed at characterizing the behavior of concrete for high confining pressures (up to 500 MPa) are reported. The main characteristics of the response under deviatoric conditions are quasi‐linearity in the elastic regime, stress‐path dependency, and gradual change from compressibility to dilatancy under increasing deviatoric stress. By performing the cyclic triaxial compression tests with several load–creep–unload and reload cycles, the time influence on the overall behavior was detected. Further, whether the main features of the observed behavior can be described within the framework of elastic/viscoplasticity theory was investigated. For this purpose, Cristescu's (Rock Rheology. Kluwer Academic Publishers: The Netherlands, 1989) approach was used. It was shown that the proposed elastic/viscoplastic model captures the main features of concrete behavior at high pressures. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
3.
Validation of a three‐dimensional constitutive model for nonlinear site response and soil‐structure interaction analyses using centrifuge test data 
下载免费PDF全文
下载免费PDF全文 The capability of a bounding surface plasticity model with a vanishing elastic region to capture the multiaxial dynamic hysteretic responses of soil deposits under broadband (eg, earthquake) excitations is explored by using data from centrifuge tests. The said model was proposed by Borja and Amies in 1994 (J. Geotech. Eng., 120, 6, 1051‐1070), which is theoretically capable of representing nonlinear soil behavior in a multiaxial setting. This is an important capability that is required for exploring and quantifying site topography, soil stratigraphy, and kinematic effects in ground motion and soil‐structure interaction analyses. Results obtained herein indicate that the model can accurately predict key response data recorded during centrifuge tests on embedded specimens—including soil pressures and bending strains for structural walls, structures' racking displacements, and surface settlements—under both low‐ and high‐amplitude seismic input motions, which was achieved after performing only a basic material parameter calibration procedure. Comparisons are also made with results obtained using equivalent linear models and a well‐known pressure‐dependent multisurface plasticity model, which suggested that the present model is generally more accurate. The numerical convergence behavior of the model in nonlinear equilibrium iterations is also explored for a variety of numerical implementation and model parameter options. To facilitate broader use by researchers and practicing engineers alike, the model is implemented as a “user material” in ABAQUS Standard for implicit time stepping. 相似文献
4.
HOU Zhenkun LI Xianwen ZHANG Yanming LIANG Huqing GUO Ying CHENG Hanlie GAO Ruchao 《《地质学报》英文版》2019,93(4):972-981
Shale, as a kind of brittle rock, often exhibits different nonlinear stress-strain behavior, failure and time-dependent behavior under different strain rates. To capture these features, this work conducted triaxial compression tests under axial strain rates ranging from 5×10?6 s?1 to 1×10?3 s?1. The results show that both elastic modulus and peak strength have a positive correlation relationship with strain rates. These strain rate-dependent mechanical behaviors of shale are originated from damage growth, which is described by a damage parameter. When axial strain is the same, the damage parameter is positively correlated with strain rate. When strain rate is the same, with an increase of axial strain, the damage parameter decreases firstly from an initial value (about 0.1 to 0.2), soon reaches its minimum (about 0.1), and then increases to an asymptotic value of 0.8. Based on the experimental results, taking yield stress as the cut-off point and considering damage variable evolution, a new measure of micro-mechanical strength is proposed. Based on the Lemaitre’s equivalent strain assumption and the new measure of micro-mechanical strength, a statistical strain-rate dependent damage constitutive model for shale that couples physically meaningful model parameters was established. Numerical back-calculations of these triaxial compression tests results demonstrate the ability of the model to reproduce the primary features of the strain rate dependent mechanical behavior of shale. 相似文献
5.
Experimental observations clearly show that the relative humidity (hr) conditions influence significantly the creep behavior of cement‐based materials, indicating that the water present within these materials plays a crucial role. This work presents a creep model for hardened cement pastes (HCP), based on a multiscale homogenization approach. It takes into account both free and adsorbed water contained in the porosity and investigates their effects on the HCP macroscopic creep behavior. The calcium silicate hydrate phase is assumed to be linear viscoelastic, and the Mori–Tanaka scheme is applied in the Laplace–Carson space to the composite formed of porosity, calcium silicate hydrate, and the other main hydrated compounds (which behavior is linearly elastic) by making use of the correspondence principle. With this model, estimations of the evolution of the macroscopic creep behavior of HCP submitted to constant external loading are examined under different hr and compared with available experimental data. Finally, a method for implementing the model in a finite element code is proposed, and simulations of standard creep tests are performed to assess its validity. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
6.
A model for the stress‐dependent elastic wave velocity response of fractured rock mass is proposed based on experimental evidence of stress‐dependent fracture normal and shear stiffness. Previously proposed models and previous experimental studies on stress‐dependent fracture stiffness have been reviewed to provide a basis for the new model. Most of the existing stress‐dependent elastic wave velocity models are empirical, with model parameters that do not have clear physical meanings. To propose the new model, the rock mass is assumed to have randomly oriented microscopic fractures. In addition, the characteristic length of microfractures is assumed to be sufficiently short compared to the rock mass dimensions. The macroscopic stress‐dependent elastic wave velocity response is assumed to be attributed to the stress dependency of fracture stiffness. The stress‐dependent fracture normal stiffness is defined as a generalized power law function of effective normal stress, which is a modification of the Goodman's model. On the other hand, the stress dependency of fracture shear stiffness is modeled as a linear function of normal stress based on experimental data. Ultrasonic wave velocity responses of a dry core sample of Berea sandstone were tested at effective stresses ranging from 2 to 55 MPa. Visual observation of thin sections obtained from the Berea sandstone confirms that the assumptions made for microstructure of rock mass model are appropriate. It is shown that the model can describe the stress‐dependent ultrasonic wave velocity responses of dry Berea sandstone with a set of reasonable material parameter values. Published 2013. This article is a U.S. Government work and is in the public domain in the USA. 相似文献
7.
For a potential geological barrier of high-level radioactive waste repositories in France, the long-term mechanical behavior of the Callovo-Oxfordian (COx) argillite is the most concern for engineers. In this paper, a micromechanical-based elasto-viscoplastic model is proposed, and its numerical realization is our main object. The COx argillite is considered as a three-phase composite consists of porous clay, quartz, and calcite. By assigning appropriate constitutive laws to those constituents, the macroscopic elasto-viscoplastic behavior of the COx argillite is determined with an extended Hill's incremental approach. The numerical aspects includes (a) a new formulation is proposed for the plastic multiplier when adopting the overstress (Perzyna) model to define the viscoplastic strain. Meanwhile, a new formulation is also proposed to solve it within the framework of an implicit returning mapping scheme. (b) The corresponding consistent tangent moduli are strictly derived by extending the method proposed for solving plastic problems; (c) the efficiency of the proposed integration algorithms for the local constitutive equations and the homogenization procedure are validated, receptively, by a built-in porous plasticity model of a commercial finite element (FE) program ABAQUS and by FE computations of a two-phase unit cell; and (d) the proposed micromechanical model is finally applied to simulate experiment data in short-term triaxial compression tests and long-term triaxial creep tests. And the numerical results show that it is able to reflect the variation of the mechanical behavior with respect to the varied mineralogical compositions. 相似文献
8.
This paper presents a biconcave bond model to investigate the effect of the cementation between grains on the mechanical behavior of rock. The proposed model considers the shape of the bonds among particles that have a biconcave cement form, based on observations of microscopic rock images. The general equations of the proposed model are based on Dvorkin theory. The accuracy and efficiency of the bond model is improved in three ways. After the biconcave bond model is implemented in the discrete element method software Particle Flow Code in 2 Dimensions, a series of numerical uniaxial compression tests were performed to investigate the relationships between the micro‐ to macro‐parameters. The simulations revealed that the biconcave bond model reflects the effect of micro‐parameters, such as the elastic modulus and Poisson's ratio of the cement, on the macroscopic deformation of cemented granular material. Variations in the bond geometry caused extremely diverse macro‐mechanical behaviors. Experimental results concerning rock demonstrate that the biconcave bond model accurately captures the mechanical behavior of intact rock and supports an innovative method for investigating the relationships between the micro‐ and macro‐parameters of cemented granular material. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
9.
This work addresses in‐plane pressure P and vertically polarized shear SV seismic wave propagation in a finite, laterally inhomogeneous, multilayered poroelastic geological region resting on the homogeneous elastic half‐space. The particular approach followed here is based on a combination of the (i) viscoelastic approximation (isomorphism) to Biot's equations of dynamic poroelasticity and on the (ii) boundary integral equation method (BIEM) using frequency‐dependent fundamental solutions of the governing wave equations. The problem is formulated under plane strain conditions and time‐harmonic motions are assumed. Validation of the viscoelastic isomorphism and verification of the BIEM is done by solution of benchmark examples. These simulation studies reveal that the proposed methodology is able to depict a sensitivity of the seismic signals recovered to the following parameters: (i) poroelastic properties of fluid saturated layers; (ii) lateral geological inhomogeneity; (iii) surface topography and (iv) frequency content and direction of the incident wave. It is concluded that the combination of viscoelastic isomorphism with BIEM software provides an effective numerical tool for evaluating site‐effect phenomena in multilayered, fluid saturated geological regions with complex geometry. The numerical results obtained demonstrate that dynamic poroelasticity interacting with other physical peculiarities of the Earth's surface layers, such as lateral heterogeneity, material properties along the wave path, local geological profile and type of elastic wave, gives rise to complex seismic signals on the free surface at the site of interest. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
10.
The unsaturated poromechanical behavior of Callovo-Oxfordian argillite (also referred to as Meuse/Haute–Marne argillite) is
analyzed by means of indentation tests at different hygrometries. Numerical simulations carried out with a finite element
code are then used to simulate flat punch indentation tests at different controlled hygrometries. The numerical response F(h) is compared to experimental data in order to estimate the drained Young’s modulus E and the internal friction angle
\Upphi\Upphi (at high confinement) by means of a back analysis. A linear decrease in the drained Young’s modulus and quasi-constant values
of the internal friction angle are observed when the relative humidity ranges. Some predictions of the model are also presented
to quantify the activation of hydraulic phenomena. Indeed, the maximal variation of the saturation and porosity relative to
the initial state of the specimen are lower than 10% and 8%, respectively. 相似文献
11.
Hyperplasticity theory was developed by Collins and Houlsby (Proc. Roy. Soc. Lon. A 1997; 453 :1975–2001) and Houlsby and Puzrin (Int. J. Plasticity 2000; 16 (9):1017–1047). Further research has extended the method to continuous hyperplasticity, in which smooth transitions between elastic and plastic behaviour can be modelled. This paper illustrates a development of a new constitutive model for soils using hyperplasticity theory. The research begins with a simple one‐dimensional elasticity model. This is extended in stages to an elasto‐plastic model with a continuous internal function. The research aims to develop a soil model, which addresses some of the shortcomings of the modified cam‐clay model, specifically the fact that it cannot model small strain stiffness, or the effects of immediate stress history. All expressions used are consistent with critical state soil mechanics terminology. Finally, a numerical implementation of the model using a rate‐dependent algorithm is described. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
12.
Solutions are presented for the problem of isothermal dessiccation shrinkage in a double‐layer porous partially saturated medium. The rheological model taken into account is linear poroelastic. Hence the analysis is mainly focused on hydromechanical coupling effects and contrasts of mechanical and hydraulic properties between two materials: a low thickness skin comprised between the outer boundary and the reference porous material. Three one‐dimensional ideal structures are taken into account: a wall of finite thickness (cartesian geometry), a thick cylinder and a thick sphere. The solution of the time‐dependent problem is arrived at by applying Laplace transforms to the field variables. Exact solutions are obtained in Laplace transform space using Mathematica© to solve the field equations whilst taking into account the continuity equations at the interface and the boundary conditions. The Talbot's modified algorithm has been performed to invert the Laplace transform solutions. A bibliographical and numerical study shows that this method is remarkably precise, stable and close to the analytical inversion. Results are presented using poroelastic data representative of a concrete material and involve a strong coupling effect between hydraulical and mechanical behaviours. A first approach elastic modelling of degradation process have been presented using a thin outer layer. Apart from emphasising the semi‐explicit solution utility due to accurate speed calculation, this paper deals with more complex problems than those which can be solved using purely analytical solutions. Copyright © 2001 John Wiley & Sons, Ltd. 相似文献
13.
The purpose of this paper is to develop the macroscopic model of hydro‐mechanical coupling for the case of a porous medium containing isolated cracks or/and vugs. In the development, we apply the asymptotic expansion homogenization method. It is shown that the general structure of Biot's model is the same as in the case of homogeneous medium, but the poro‐elastic parameters are modified. Two numerical examples are presented. They concern the computations of Biot's parameters in isotropic and anisotropic cases. It can also be seen how the presence of near‐zero‐volume cracks influences Biot's parameters of the porous matrix. It can significantly affect the coupled hydro‐mechanical behaviour of damaged porous medium. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
14.
15.
A new phenomenological macroscopic constitutive model for the numerical simulation of quasi‐brittle fracture and ductile concrete behavior, under general triaxial stress conditions, is presented. The model is particularly addressed to simulate a wide range of confinement stress states, as also, to capture the strong influence of the mean stress value in the concrete failure mechanisms. The model is based on a two‐surface damage‐plastic formulation. The mechanical behavior in different domains of the stress space is separately described by means of a quasi‐brittle or ductile material response:
16.
This paper presents an advanced thermomechanical model – TEAM in the framework of two‐surface plasticity for saturated clays, with emphasis put on some important thermomechanical features of natural clays evidenced experimentally such as the limited thermomechanical elastic zone, the smooth transition from elastic to plastic behavior. Two plastic mechanisms are introduced in the model: one is to reproduce the thermoplasticity involving thermal expansion and contraction observed at high over‐consolidation ratios and the second one describes the temperature effect on the yield behavior. The model adopts additional yield surfaces, namely inner yield surfaces that are associated with the two proposed plastic mechanisms to account for the plastic behavior inside the existing conventional thermomechanical yield surface namely yield surfaces. The general expressions of the yield surfaces and plastic potentials in p′–q–T space are introduced. A progressive plastic hardening mechanism associated with the inner yield surface is defined, enabling the plastic modulus to vary smoothly during thermomechanical loadings inside the yield surfaces. Several tests on natural Boom clay along different thermomechanical loading paths have been simulated by TEAM, and results show its relevance in describing the thermomechanical behavior of saturated clays. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
17.
描述岩石粘弹性固体性质的开尔文模型 总被引：1，自引：0，他引：1
大多数固体材料都具有弹性,但真实的固体却极少严格遵从弹性的虎克定律。这些固体材料的变形往往有对时间的依赖性,这种性质是流变学研究的内容。岩石是自然界最普遍的固体,它的力学性质在通常条件下可用虎克定律作精确的描述,而在漫长的地质过程中,岩石的流变特征就逐渐显现出来。地质作用越缓慢,岩石对变形时间的依赖性越明显。为精确描述岩石在地质过程的力学性质,流变学方法被引入地质学。笔者已经介绍过描述"牛顿流体"的马克斯威尔流变模型,文中介绍描述粘弹性固体的开尔文流变模型。和马克斯威尔模型一样,开尔文模型也是流变学的基本模型,它是由一个弹性元件和一个阻尼元件并联而成。文中给出开尔文模型的本构关系和地质应用的简介。 相似文献
18.
19.
Clayey rocks are frequently chosen as a geological barrier material for underground repositories. The inherent anisotropic mechanical behavior and the evolution of mechanical behavior with water content are two crucial material properties for the safety analysis of these structures. The present paper focuses on numerical modeling of the inherent anisotropy and the effect of water content, as well as the interactions of these properties in partially saturated clayey rocks with preferably oriented bedding planes. A discrete thermodynamic approach is adopted for describing the inherent anisotropic mechanical behavior, and the anisotropy of the elastic parameters, plastic evolution and damage evolution are considered. Capillary pressure is introduced to describe the effect of the water content with the help of the effective stress concept, and a procedure for the identification of the model parameters is presented. Finally, the proposed model is applied to a study of triaxial compression tests of argillite with different orientations of the bedding planes and variable water content. In summary, the main features of the studied material are well reproduced by the model. 相似文献
20.
This paper presents a three‐dimensional energy‐based solution for the time‐dependent response of a deeply embedded and unsupported semi‐infinite tunnel of circular cross‐section. The tunnel is taken to be excavated quasi‐instantaneously from an infinite rock body that initially exhibits an isotropic stress state and that is made up of a homogeneous, isotropic and viscoelastic material. The viscoelastic behaviour is modelled by means of Burger's model, and the rock is taken to behave volumetrically linear elastic and to exhibit exclusively deviatoric creep. This viscoelastic problem is transformed into the Laplace domain, where it represents a quasi‐elastic problem. The displacement fields in the new solution are taken to be the products of independent functions that vary in the radial and longitudinal directions. The differential equations governing the displacements of the system and appropriate boundary conditions are obtained using the principle of minimum potential energy. The solutions for these governing equations in the Laplace domain are then obtained analytically and numerically using a one‐dimensional finite difference technique. The results are then transformed back into the time domain using an efficient numerical scheme. The accuracy of the new solution is comparable with that of a finite element analysis but requires much less computation effort. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献