首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
Viscous and other damping devices are often used as elements of seismic isolation systems. Despite the widespread application of nonlinear viscous systems particularly in Japan (with fewer applications in the USA and Taiwan), the application of viscous damping devices in isolation systems in the USA progressed intentionally toward the use of supplementary linear viscous devices due to the advantages offered by these devices. This paper presents experimental results on the behavior of seismically isolated structures with low damping elastomeric (LDE) and single friction pendulum (SFP) bearings with and without linear and nonlinear viscous dampers. The isolation systems are tested within a six‐story structure configured as moment frame and then again as braced frame. Emphasis is placed both on the acquisition of data related to the structural system (drifts, story shear forces, and isolator displacements) and on non‐structural systems (floor accelerations, floor spectral accelerations, and floor velocities). Moreover, the accuracy of analytical prediction of response is investigated based on the results of a total of 227 experiments, using 14 historic ground motions of far‐fault and near‐fault characteristics, on flexible moment frame and stiff braced frame structures isolated with LDE or SFP bearings and linear or nonlinear viscous dampers. It is concluded that when damping is needed to reduce displacement demands in the isolation system, linear viscous damping results in the least detrimental effect on the isolated structure. Moreover, the study concludes that the analytical prediction of peak floor accelerations and floor response spectra may contain errors that need to be considered when designing secondary systems. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

2.
Base isolation has been established as the seismic design approach of choice when it comes to protecting nonstructural contents. However, while this protection technology has been widely shown to reduce seismic demands on attached oscillatory equipment and contents (EC), its effectiveness in controlling the response of freestanding EC that are prone to sliding has not been investigated. This study examines the seismic behavior of sliding EC inside base‐isolated buildings subjected to broadband ground motions. The effect of isolation system properties on the response of sliding EC with various friction coefficients is examined. Two widely used isolation models are considered: viscously damped linear elastic and bilinear. The study finds isolation to be generally effective in reducing seismic demands on sliding EC, but it also exposes certain situations where isolation in fact increases demands on EC, most notably for low friction coefficients and high earthquake intensities. Damping at the isolation level is effective in controlling the EC sliding displacements, although damping over about 20% is found to be superfluous. The study identifies a physically motivated dimensionless intensity measure and engineering demand parameter for sliding equipment in base‐isolated buildings subjected to broadband ground motions. Finally, the paper presents easy‐to‐use design fragility curves and an example that illustrates how to use them. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

3.
Semi‐active variable stiffness resettable devices can reduce seismic demands and damages in structures. Despite their advantages, variable stiffness resettable devices are under‐utilized mainly because of the shortage of fundamental research in quantifying the sensitivity of key seismic response parameters, and losses, in structures that use such systems for seismic hazard mitigation. Within this setting, the research summarized herein measures the effectiveness of semi‐active resettable energy dissipating devices in the Single‐Degree‐of‐Freedom domain aiming at quantifying the sensitivity of their seismic response to variation in control parameters and generating the required knowledge to utilize such semi‐active devices in the Multi‐Degree‐of‐Freedom domain. The performance (i.e. maximum relative displacement and peak absolute acceleration demands) of Single‐Degree‐of‐Freedom systems with an array of semi‐active control logics under various dynamic excitation regimes is studied. Two sets of 40 ground motions representing various seismic loading conditions (i.e. pulse‐like and rock‐site ground motions) are used, and an efficient control logic for mitigating these seismic demands is proposed. Numerical results show that proposed control logic enables a decrease of 40–60% for both maximum relative displacement and seismic base shear and 15–25% decrease for peak absolute acceleration. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

4.
In this study, the multi‐intensity seismic response of code‐designed conventional and base‐isolated steel frame buildings is evaluated using nonlinear response history analysis. The results of hazard and structural response analysis for three‐story braced‐frame buildings are presented in this paper. Three‐dimensional models for both buildings are created and seismic response is assessed for three scenario earthquakes. The response history analysis results indicate that the design objectives are met and the performance of the isolated building is superior to the conventional building in the design event. For the Maximum Considered Earthquake, isolation leads to reductions in story drifts and floor accelerations relative to the conventional building. However, the extremely high displacement demands of the isolation system could not be accommodated under normal circumstances, and creative approaches should be developed to control displacements in the MCE. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

5.
A probabilistic approach to estimate maximum inelastic displacement demands of single‐degree‐of‐freedom (SDOF) systems is presented. By making use of the probability of exceedance of maximum inelastic displacement demands for given maximum elastic spectral displacement and the mean annual frequency of exceedance of elastic spectral ordinates, a simplified procedure is proposed to estimate mean annual frequencies of exceedance of maximum inelastic displacement demands. Simplifying assumptions are thoroughly examined and discussed. Using readily available elastic seismic hazard curves the procedure can be used to compute maximum inelastic displacement seismic hazard curves and uniform hazard spectra of maximum inelastic displacement demands. The resulting maximum inelastic displacement demand spectra provide a more rational way of establishing seismic demands for new and existing structures when performance‐based approaches are used. The proposed procedure is illustrated for elastoplastic SDOF systems having known‐lateral strength located in a region of high seismicity in California. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

6.
The American Society of Civil Engineers (ASCE) 43‐05 presents two performance objectives for the design of nuclear structures, systems and components in nuclear facilities: (1) 1% probability of unacceptable performance for 100% design basis earthquake (DBE) shaking and (2) 10% probability of unacceptable performance for 150% DBE shaking. To aid in the revision of the ASCE 4‐98 procedures for the analysis and design of base‐isolated nuclear power plants and meet the intent of ASCE 43‐05, a series of nonlinear response‐history analyses was performed to study the impact of the variability in both earthquake ground motion and mechanical properties of isolation systems on the seismic responses of base‐isolated nuclear power plants. Computations were performed for three representative sites (rock and soil sites in the Central and Eastern United States and a rock site in the Western United States) and three types of isolators (lead rubber, Friction Pendulum and low‐damping rubber bearings) using realistic mechanical properties for the isolators. Estimates were made of (1) the ratio of the 99th percentile (90th percentile) response of isolation systems computed using a distribution of spectral demands and distributions of isolator mechanical properties to the median response of isolation systems computed using best‐estimate properties and 100% (150%) spectrum‐compatible DBE ground motions; (2) the number of sets of three‐component ground motions to be used for response‐history analysis to develop a reliable estimate of the median response of isolation systems. The results of this study provide the technical basis for the revision of ASCE Standard 4‐98. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

7.
This paper describes a proposed methodology, referred to as probabilistic seismic control analysis, for the development of probabilistic seismic demand curves for structures with supplemental control devices. The resulting curves may be used to determine the probability that any response measure, whether for a structure or control device, exceeds a pre‐determined allowable limit. This procedure couples conventional probabilistic seismic hazard analysis with non‐linear dynamic structural analyses to provide system specific information. This method is performed by evaluating the performance of specific controlled systems under seismic excitations using the SAC Phase II structures for the Los Angeles region, and three different control‐systems: (i) base isolation; (ii) linear viscous brace dampers; and (iii) active tendon braces. The use of a probabilistic format allows for consideration of structural response over a range of seismic hazards. The resulting annual hazard curves provide a basis for comparison between the different control strategies. Results for these curves indicate that no single control strategy is the most effective at all hazard levels. For example, at low return periods the viscous system has the lowest drift demands. However, at higher return periods, the isolation system becomes the most effective strategy. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

8.
The restoring capability (or re‐centering capability) is identified by the current design codes as a fundamental feature of seismic isolation systems. In this paper, the restoring capability of bilinear hysteretic or frictional seismic isolation systems is investigated in some detail. Certain energy considerations are examined first in order to provide insight into and reveal governing parameters on individual aspects of the problem. The restoring capability is then investigated through an extensive parametric study of smooth bilinear single‐degree‐of‐freedom hysteretic systems, with parameters covering a range of typical seismic isolation systems, subjected to a large group of recorded earthquakes. The results of the parametric analyses are processed statistically and regression analysis relations are derived that show the dependence of the residual displacement after the earthquake and the cumulative build up of displacements after a series of successive earthquakes on the governing parameters. Based on the analysis results, the features of the bilinear system that ensure sufficient restoring capability are identified. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

9.
The seismic response of light secondary systems in a building is dependent on the response of the primary structural system to the seismic ground motion with the result that very high accelerations can be induced in such secondary systems. This response can be reduced through the use of aseismic base isolation which is a design strategy whereby the entire building can be decoupled from the damaging horizontal components of seismic ground motion by the use of some form of isolation system. The paper presents a theoretical analysis of the response of light equipment in isolated structures and a parallel experimental programme both of which show that the use of base isolation can not only attenuate the response of the primary structural system but also reduce the response of secondary systems. Thus, the design of equipment and piping in a base-isolated building is very much simpler than that for a conventionally founded structure: inelastic response and equipment-structure interaction need not be considered and multiple support response analysis is rendered unnecessary. Although an isolation system with linear elastic bearings can reduce the acceleration of the structure, it may be accompanied by large relative displacements between the structure and the ground. A system using lead-rubber hysteretic bearings, having a force-displacement relation which is approximately a bilinear loop, can reduce these displacements. A parallel experimental programme was carried out to investigate the response of light equipment in structures isolated using lead-rubber bearings. The experimental results show that these bearings can dissipate energy and limit the displacement and acceleration of the structure but are less effective in reducing the accelerations in the internal equipment. The results of both the analysis and the tests show that base isolation is a very effective method for the seismic protection of light equipment items in buildings.  相似文献   

10.
考虑耦联影响的二次结构体系减震分析   总被引：3，自引：2，他引：1  
建立了基础隔震的主次结构体系耦联运动方程,开发了动力分析程序PS—BASE．FOR,对一典型结构的二次结构绝对加速度反应谱与相对位移反应谱计算分析表明,主体结构隔震或同时增大二次结构阻尼,是取得二次结构较好抗震性能的有效途径,增大主体结构的隔震阻尼对二次结构略有不利影响。  相似文献   

11.
Inter‐story isolation, an effective strategy for mitigating the seismic risk of both new and existing buildings, has gained more and more interest in recent years as alternative to base isolation, whenever the latter results to be impractical, technically difficult or uneconomic. As suggested by the name, the technique consists in inserting flexible isolators at floor levels other than the base along the height of a multi‐story building, thus realizing a non‐conventional Tuned Mass Damper (TMD). Consistent with this, an optimal design methodology is developed in the present paper with the objective of achieving the global protection of both the structural portions separated by the inter‐story isolation system, that is, the lower portion (below the isolation system) and the isolated upper portion (above the isolation system). The optimization procedure is formulated on the basis of an energy performance criterion that consists in maximizing the ratio between the energy dissipated in the isolation system and the input energy globally transferred to the entire structure. Numerical simulations, performed under natural accelerograms with different frequency content and considering increasing isolation levels along the height of a reference frame structure, are used to investigate the seismic performance of the optimized inter‐story isolation systems. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

12.
An Erratum has been published for this article in Earthquake Engng. Struct. Dyn. 2004; 33:1429. Based on structural dynamics theory, the modal pushover analysis (MPA) procedure retains the conceptual simplicity of current procedures with invariant force distribution, now common in structural engineering practice. The MPA procedure for estimating seismic demands is extended to unsymmetric‐plan buildings. In the MPA procedure, the seismic demand due to individual terms in the modal expansion of the effective earthquake forces is determined by non‐linear static analysis using the inertia force distribution for each mode, which for unsymmetric buildings includes two lateral forces and torque at each floor level. These ‘modal’ demands due to the first few terms of the modal expansion are then combined by the CQC rule to obtain an estimate of the total seismic demand for inelastic systems. When applied to elastic systems, the MPA procedure is equivalent to standard response spectrum analysis (RSA). The MPA estimates of seismic demand for torsionally‐stiff and torsionally‐flexible unsymmetric systems are shown to be similarly accurate as they are for the symmetric building; however, the results deteriorate for a torsionally‐similarly‐stiff unsymmetric‐plan system and the ground motion considered because (a) elastic modes are strongly coupled, and (b) roof displacement is underestimated by the CQC modal combination rule (which would also limit accuracy of RSA for linearly elastic systems). Copyright © 2004 John Wiley & Sons, Ltd.  相似文献   

13.
This paper assesses the influence of cyclic and in‐cycle degradation on seismic drift demands in moment‐resisting steel frames (MRF) designed to Eurocode 8. The structural characteristics, ground motion frequency content, and level of inelasticity are the primary parameters considered. A set of single‐degree‐of‐freedom (SDOF) systems, subjected to varying levels of inelastic demands, is initially investigated followed by an extensive study on multi‐storey frames. The latter comprises a large number of incremental dynamic analyses (IDA) on 12 frames modelled with or without consideration of degradation effects. A suite of 56 far‐field ground motion records, appropriately scaled to simulate 4 levels of inelastic demand, is employed for the IDA. Characteristic results from a detailed parametric investigation show that maximum response in terms of global and inter‐storey drifts is notably affected by degradation phenomena, in addition to the earthquake frequency content and the scaled inelastic demands. Consistently, both SDOF and frame systems with fundamental periods shorter than the mean period of ground motion can experience higher lateral strength demands and seismic drifts than those of non‐degrading counterparts in the same period range. Also, degrading multi‐storey frames can exhibit distinctly different plastic mechanisms with concentration of drifts at lower levels. Importantly, degrading systems might reach a “near‐collapse” limit state at ductility demand levels comparable to or lower than the assumed design behaviour factor, a result with direct consequences on optimised design situations where over‐strength would be minimal. Finally, the implications of the findings with respect to design‐level limit states are discussed.  相似文献   

14.
The accuracy of the three‐dimensional modal pushover analysis (MPA) procedure in estimating seismic demands for unsymmetric‐plan buildings due to two horizontal components of ground motion, simultaneously, is evaluated. Eight low‐and medium‐rise structures were considered. Four intended to represent older buildings were designed according to the 1985 Uniform Building Code, whereas four other designs intended to represent newer buildings were based on the 2006 International Building Code. The median seismic demands for these buildings to 39 two‐component ground motions, scaled to two intensity levels, were computed by MPA and nonlinear response history analysis (RHA), and then compared. Even for these ground motions that deform the buildings significantly into the inelastic range, MPA offers sufficient degree of accuracy. It is demonstrated that PMPA, a variant of the MPA procedure, for nonlinear systems is almost as accurate as the well‐known standard response spectrum analysis procedure is for linear systems. Thus, for practical applications, the PMPA procedure offers an attractive alternative to nonlinear RHA, whereby seismic demands can be estimated directly from the (elastic) design spectrum. In contrast, the nonlinear static procedure specified in the ASCE/SEI 41‐06 Standard is demonstrated to grossly underestimate seismic demands for some of the unsymmetric‐plan buildings considered. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

15.
The seismic response of a critical rotating machine either rigidly attached to a floor or independently isolated housed within an initially aseismically designed or uncontrolled structure are investigated. A particular isolation system, the Resilient‐Friction Base Isolator (RFBI), is employed. Finite element formulations of a rotor‐disk‐bearing model on a rigid base are developed. The equations of motion for the combined rotating machine–structure–RFBI systems are presented. Parametric studies are performed to investigate the effects of variations in system physical properties including friction coefficient, mass ratio, shaft flexibility, bearing rigidity, bearing damping and speed of rotation on the response of rotating machines for the combined rotating machine–structure–isolator systems. Comparative studies in the peak response of the rotating machine supported on various isolation systems and the corresponding fixed base system are carried out. The study indicates that the Resilient‐Friction Base Isolator can significantly reduce the seismic response of rotating components to potentially damaging ground excitations. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

16.
Requirements for the seismic resistance of nuclear power plants (NPPs) considerably differ from those for of other industrial facilities due to the necessity of protecting not only the NPP itself, but also the environment from radiation hazard. According to special regulations, even if an NPP construction site is located in a region with low seismicity, the NPP design should be based on the maximum design earthquake and peak acceleration typical of the region. Note that seismic warning systems for NPPs differ fundamentally in design and operation principles from conventional seismic monitoring systems. Seismic warning systems are required to reliably detect seismic events threatening the operability of nuclear power plants, to promptly inform operators, and to prevent false alarms and unauthorized access to the system. Atomseismoizyskaniya LLC has developed a seismic warming system (SSZ-1M) and put it into trial operation at the reactor units of the Smolensk NPP in 2014–2015. The system comprises six seismic groups: two groups per each reactor unit. Each group consists of three independent seismic recording channels, the sensors of which are distributed around the reactor unit at a distance of up to 500 m from the latter. Each channel records three components of seismic signals; the acceleration vector is calculated and compared with a preset threshold. Signals exceeding the threshold are fed to a coincidence circuit that generates an alarm if two of the three signals exceed the threshold. This scheme excludes false alarms. The components of the system are characterized by high reliability and stability. The performance of the system channels has been officially certified. The system automatically performs continuous fault diagnosis. The programs responsible for system function and diagnostics are independent; the system units have individual equipment. To exclude the possibility of external impacts, the SSZ-1M warning system has no Internet connection. Special seismic signal simulators were developed to test the operability of the system when deployed.  相似文献   

17.
核电工程应用隔震技术的可行性探讨   总被引：3，自引：0，他引：3  
本文旨在观察和分析有关基底隔震技术在核电工程中应用的相关问题,重点讨论如何将此类已经相当成熟的技术应用于核电这一类十分特殊、十分重要、十分敏感而又十分复杂的工程中.文中指出隔震技术有很多优点,可以整体改进核电工程的安全性和可靠性,有利于促进未来核电厂设计和建造的标准化,缩短建设时间,降低建厂的初始投资和生命周期中的运行...  相似文献   

18.
The effectiveness of seismic isolation in protecting structural and non‐structural elements from damage has been assessed in an extensive programme of shaking‐table tests, carried out on four identical 1/3.3‐scale, two‐dimensional, reinforced concrete (R/C) frames. Four different isolation systems were considered, namely: (i) rubber‐based, (ii) steel‐based, (iii) shape memory alloy (SMA)‐based and (iv) hybrid, i.e. based on both SMA and steel components, isolation systems. This paper presents a comprehensive overview of the main results of the experimental tests on base‐isolated models, whose structural response is described through: (i) maximum base displacements; (ii) maximum interstorey drifts; (iii) maximum storey accelerations and (iv) maximum storey shear forces. The evolution of the fundamental frequency of vibration of the R/C frame during the tests is also described. The beneficial effects of using base isolation resulted in no or slight damage, under strong earthquakes, to both structural and non‐structural members, as well as to the internal content of the building. The comparison with the experimental results obtained in shaking‐table tests on similar fixed‐base models emphasizes these positive aspects. Finally, advantages and drawbacks related to the use of each isolation system are discussed in the paper. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

19.
The paper deals with the seismic reliability of elastic structural systems equipped with friction pendulum isolators (friction pendulum system). The behavior of these systems is analyzed by employing a two‐degree‐of‐freedom model accounting for the superstructure flexibility, whereas the friction pendulum system device behavior is described by adopting a widespread model that considers the variation of the friction coefficient with the velocity. With reference to medium soil condition, the uncertainty in the seismic inputs is taken into account by considering a set of artificial records, obtained through Monte Carlo simulations within the power spectral density method, with different frequency contents and characteristics depending on the soil dynamic parameters and scaled to increasing intensity levels. The sliding friction coefficient at large velocity is also considered as random variable modeled through a uniform probability density function. Incremental dynamic analyses are developed in order to evaluate the probabilities exceeding different limit states related to both r.c. superstructure and isolation level defining the seismic fragility curves through an extensive parametric study carried out for different structural system properties. Finally, considering the seismic hazard curves related to a site near L'Aquila (Italy), the seismic reliability of the r.c. superstructure systems is evaluated, and seismic reliability‐based design abacuses are derived with the aim to define the radius in plan of the friction pendulum devices in function of the structural properties and reliability level expected. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

20.
Controlled rocking steel frames have been proposed as an efficient way to avoid the structural damage and residual deformations that are expected in conventional seismic force resisting systems. Although the base rocking response is intended to limit the force demands, higher mode effects can amplify member design forces, reducing the viability of the system. This paper suggests that seismic forces may be limited more effectively by providing multiple force‐limiting mechanisms. Two techniques are proposed: detailing one or more rocking joints above the base rocking joint and providing a self‐centring energy dissipative (SCED) brace at one or more levels. These concepts are applied to the design of an eight‐storey prototype structure and a shake table model at 30% scale. A simple numerical model that was used as a design tool is in good agreement with frequency characterization and low‐amplitude seismic tests of the shake table model, particularly when multiple force‐limiting mechanisms are active. These results suggest that the proposed mechanisms can enable better capacity design by reducing the variability of peak seismic force demands without causing excessive displacements. Similar results are expected for other systems that rely on a single location of concentrated nonlinearity to limit peak seismic loads. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号