首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 46 毫秒
1.
The use of shear wave velocity (V s) measurements as an in situ test for evaluation of liquefaction potential has increased substantially due to its advantages. Relatively large numbers of studies have been performed to establish the correlation between V s and liquefaction resistance (CRR) of clean sands. Usually, natural sands contain silt and/or clay, and previous studies have shown that both the amount of fines and their nature influence the values of CRR as well as V s. Therefore, the CRR–V s correlations may also be affected by fines content and type of sandy soils. However, effect of fines content and especially fines type of sandy soils on the correlation between V s and CRR is inadequately addressed in the literature. In this study, cyclic triaxial and bender element tests were conducted on samples of sand containing various amounts of different types of fines, and the effects of fines on the values of CRR and V s are investigated. The results show that G 0 and CRR reduce even when small amounts of fines are added to sand. Therefore, use of plasticity index (PI) of the fines fraction is better than the PI of the overall soil when trying to assess the effects of fines. Using obtained experimental data as well as the established semiempirical CRR–V s relationship, the CRR–V s correlation was developed for all the tested soils, and the effect of fines type on the correlation is also examined. Based on the results obtained in this study, CRR–V s correlation is affected by both the amount and the plasticity of the fines present in the sand, and this correlation is soil specific.  相似文献   

2.
  相似文献   

3.
  相似文献   

4.
In the present study, four different heuristic techniques viz. multi-layer perceptron (MLP), radial basis function (RBF), self-organizing maps (SOM), and co-active neuro-fuzzy inference system (CANFIS) with hyperbolic tangent and sigmoid transfer functions and two regression-based techniques, i.e., multiple linear regression (MLR) and sediment-rating curve (SRC), were used for suspended sediment modeling. Gamma test (GT), correlation function (CF), M test, and trail–error procedure were applied for estimation of appropriate input variables as well as training data length. The results of the GT and CF suggested the five input variables (Qt, Qt?1, Qt?2, St?1, and St?2, where Qt?1 and St?1 indicate the discharge and sediment values of one previous day) as the best combination. The optimal training data length (75% of total data) was estimated by M test and trail–error procedure for development of the applied models. The MLP with sigmoid transfer function (M-2) performed better than the all other models. The results of sensitivity analysis indicated that the present-day discharge (Qt), 1-day lag discharge (Qt?1) and 1-day lag suspended sediment (St?1) are the most influenced parameters in modeling current day suspended sediment (St).  相似文献   

5.
  相似文献   

6.
A new class of figures of equilibrium for a rotating gravitating fluid located inside a gravitating ring or torus is studied. These figures form a family of sequences of generalized oblate spheroids, in which there is for any value of the tidal parameter α in the interval 0 ≤ \(0 \leqslant \frac{\alpha }{{\pi G\rho }} \leqslant 0.1867\) ≤ 0.1867 a sequence of spheroids with oblatenesses emin (α) ≤ e ≤ emax (α). A series of classicalMaclaurin spheroids from a sphere to a flat disk is obtained for α = 0. At intermediate values 0 < α ≤ αmax, there are two limiting non-rotating spheroids in each sequence. When α = αmax, the sequence degenerates into a single non-rotating spheroid with ecr ≈ 0.9600, corresponding to the maximum oblateness of E7 elliptical galaxies. The second part of the paper considers the influence of rings of dark matter on the dynamics of elliptical galaxies. It is proposed that the equilibrium of an oblate isolated non-rotating galaxy is unstable, and it cannot be supported purely by anisotropy of the stellar velocity dispersion. A ring of dark matter can stabilize a weakly rotating galaxy, supplementing standard dynamical models for such stellar systems. In order for a galaxy to acquire appreciable oblateness, the mass of the ring must be an order of magnitude higher than the mass of the galaxy itself, consistent with the ratios of the masses of dark and baryonic matter in the Universe. The influence of massive external rings could shed light on the existence of galaxies with the critical oblateness E7.  相似文献   

7.
In this study, single crystals of pure enstatite (Mg2Si2O6) were synthesised under water-saturated conditions at 4 and 8 GPa and 1,150°C with variable silica activity, leading to phase assemblages enstatite + forsterite, enstatite or enstatite + coesite. Run products were investigated using an FTIR spectrometer equipped with a focal plane array detector enabling IR imaging with a lateral pixel resolution of 2.7 μm. IR spectra within the OH-absorption region show two different groups of absorption bands: group 1 (wavenumbers at 3,592 and 3,687 cm?1) shows strongest absorptions for E||n β, whereas group 2 (wavenumbers at 3,067 and 3,362 cm?1) shows strongest absorptions for E||n γ. The groups are related to different defect types, group 1 to tetrahedral defects (T-site vacancies) and group 2 to octahedral defects (M-site vacancies). The intensity ratio of the bands within one group (i.e. A 3067/A 3362 and A 3592/A 3687) and the intensity ratio of E||n γ and E||n α in group 2 bands remain constant within error. In contrast, the intensity ratio of group 2 to group 1 absorption bands [e.g. (A 3362)/(A 3687)] is sensitive to the SiO2 activity and pressure. On the basis of the results of this and previous studies, a barometer for pure orthoenstatite coexisting with forsterite can be formulated:\( P\,[{\text{GPa}}] = 1.056 + \sqrt {{\frac{{1.025 - A_{{\left( {3362} \right)/\left[ {(3362) + (3687)} \right]}} }}{0.009}}} , \) where A (3362) and A (3687) are the integral absorbances of the component E||n γ of the absorption bands at 3,362 cm?1 and the component E||n β of the absorption band at 3,687 cm?1, respectively.  相似文献   

8.
The strong adaptability of Broussonetia papyrifera (L.) Vent. to low phosphorus (P) conditions can be attributed to the large amount of root-exuded organic acids and the high efficiency of P extraction. However, microelement contents are influenced by low-P stress, and their effects on the photosynthetic capability of B. papyrifera remain unknown. In this study, we investigated the effects of low-P treatment on net photosynthetic rate (P N); chlorophyll a fluorescence (ChlF) characteristics; and Fe, Mn, Cu, and Zn contents of B. papyrifera and Morus alba L. seedlings. Results show that B. papyrifera exhibited better photosynthetic capability under moderate P deficiency (0.125, 0.063, and 0.031 mmol/L P treatments), whereas the photosynthetic capability of M. alba decreased under moderate and severe P deficiency (0.016 and 0 mmol/L P treatments). Under moderate P deficiency, the decrease in Cu and Zn contents in B. papyrifera was lower than that in M. alba. Under severe P deficiency, a considerable decrease of photosynthetic capability in B. papyrifera and M. alba was associated with low Cu and Zn contents. The P N of the two Moraceae species exhibited a better correlation with Cu and Zn contents than with Fe or Mn content. P deficiency could not only decrease cyclic photophorylation and photosynthetic efficiency, but could also affect the stability of thylakoid membrane structure and electron transport efficiency by influencing the contents of Cu or Zn, thereby affecting photosynthesis.  相似文献   

9.
Present work provides in-situ structural data at a fine temperature scale from RT to the melting point of nitratine, NaNO3. From the analysis of log e 33 versus log t plots, it is possible to prove that an univocal indication on the R \( \overline{3} \) c (low temperature, LT) → R \( \overline{3} \) m (high temperature, HT) transition mechanism cannot be obtained because of the relevant role played by the arbitrary assumptions required for defining the c 0 dependence from temperature of the HT phase. This is due to the occurrence of excess thermal expansion for the HT phase. A significantly better fit for an Ising-spin structural model over a non-Ising rigid-body one has been obtained for the LT phase. Moreover, the Ising model led to a smooth variation of the oxygen site x fractional coordinate throughout the transition. The structure of the HT polymorph has been successfully refined considering an oxygen site at x, 0, ½, with 50% occupancy. Such model was the only acceptable one from the crystal chemical point of view as the alternative model (oxygen site at x, y, z with 25% occupancy) led to unrealistically aplanar \( {\text{NO}}_{3}^{ - } \) groups.  相似文献   

10.
We apply the general concept of seismic risk analysis based on morphostructural analysis of the territory, pattern recognition of earthquake-prone nodes, and the Unified Scaling Law for Earthquakes, USLE, in another seismic region of Russia to the west from Lake Baikal, i.e., Altai–Sayan Region. The USLE generalizes the empirical Gutenberg–Richter relationship making use of apparently fractal distribution of earthquake sources of different size: \( \log_{10} N\left( {M,L} \right)\, = \,A\, + \,B \cdot \left( {5\, - \,M} \right)\, + \,C \cdot \log_{10} L, \) where N (M, L) is the expected annual number of earthquakes of a certain magnitude M within an seismically prone area of linear dimension L. The local estimates of A, B, and C allow determination of the expected maximum credible magnitude in a given time interval and the associated spread around ground shaking parameters (e.g., peak ground acceleration, PGA, or macroseismic intensity, I0). Compilation of the corresponding seismic hazard map of Altai–Sayan Region and its rigorous testing against the available seismic evidences in the past is used to model regional maps of specific earthquake risks for population, cities, and infrastructures.  相似文献   

11.
The unnamed mineral CuFe2S4 has been found from sulfide Cu–Ni ores of the Lovnoozero deposit in the Kola Peninsula, Russia. It occurs in norite composed of orthopyroxene (bronzite), Ca-rich plagioclase (66% An), pargasite, and phlogopite. The last two minerals are replaced by talc, chlorite and carbonates. Monoclinic pyrrhotite, pentlandite, chalcopyrite, and pyrite are associated ore minerals. Phase CuFe2S4 is enclosed predominantly in chalcopyrite, probably replacing it, and occurs in later carbonate veinlets together with redeposited sulfides. It is light yellow with a brownish tint and metallic luster. The Mohs hardness is 5–5.5; VHN 654 ± 86 kgs/mm2. Density (calc.) = 4.524 g/cm3. The mineral is anisotropic, internal reflections are absent. Reflectance values (λ, nm R′ g and R′ p %) are: 440 30.3 29.5, 500 43.7 42.8, 560 50.9 49.6, 620 52.4 51.2, 640 52.6 51.4, 680 52.8 51.6, 700 52.7 51.4. CuFe2S4 is monoclinic, a = 6.260(4), b = 5.39(1), c = 13.19(1) Å, β = 94.88(7)°, V = 443(1) Å3, Z = 4. The strongest reflections in the powder diffraction pattern are [d, Å (I) (hkl)]: 4.150 (10) (012), 3.559 (4) (\(11\bar 2\)), 3.020 (4) (\(10\bar 4\)), 2.560 (3) (\(21\bar 2\)), 2.500 (3) (\(10\bar 5\)), 2.340 (3) (\(12\bar 2\)), 1.817 (3) (215), 1.489 (3) (402). The chemical composition is as follows, wt %: 20.44 Cu, 35.85 Fe, 0.65 Ni, 0.14 Co, 43.15 S, total is 100.23. The empirical formula calculated on the basis of 7 atoms is Cu0.969(Fe1.934Ni0.034Co0.007)1.975S4.056. According to its mode of occurrence, the mineral was formed as a result of low temperature processes involving metamorphic hydrothermal solutions.  相似文献   

12.
Isotope fractionation during the evaporation of silicate melt and condensation of vapor has been widely used to explain various isotope signals observed in lunar soils, cosmic spherules, calcium–aluminum-rich inclusions, and bulk compositions of planetary materials. During evaporation and condensation, the equilibrium isotope fractionation factor (α) between high-temperature silicate melt and vapor is a fundamental parameter that can constrain the melt’s isotopic compositions. However, equilibrium α is difficult to calibrate experimentally. Here we used Mg as an example and calculated equilibrium Mg isotope fractionation in MgSiO3 and Mg2SiO4 melt–vapor systems based on first-principles molecular dynamics and the high-temperature approximation of the Bigeleisen–Mayer equation. We found that, at 2500 K, δ25Mg values in the MgSiO3 and Mg2SiO4 melts were 0.141?±?0.004 and 0.143?±?0.003‰ more positive than in their respective vapors. The corresponding δ26Mg values were 0.270?±?0.008 and 0.274?±?0.006‰ more positive than in vapors, respectively. The general \(\alpha - T\) equations describing the equilibrium Mg α in MgSiO3 and Mg2SiO4 melt–vapor systems were: \(\alpha_{{{\text{Mg}}\left( {\text{l}} \right) - {\text{Mg}}\left( {\text{g}} \right)}} = 1 + \frac{{5.264 \times 10^{5} }}{{T^{2} }}\left( {\frac{1}{m} - \frac{1}{{m^{\prime}}}} \right)\) and \(\alpha_{{{\text{Mg}}\left( {\text{l}} \right) - {\text{Mg}}\left( {\text{g}} \right)}} = 1 + \frac{{5.340 \times 10^{5} }}{{T^{2} }}\left( {\frac{1}{m} - \frac{1}{{m^{\prime}}}} \right)\), respectively, where m is the mass of light isotope 24Mg and m′ is the mass of the heavier isotope, 25Mg or 26Mg. These results offer a necessary parameter for mechanistic understanding of Mg isotope fractionation during evaporation and condensation that commonly occurs during the early stages of planetary formation and evolution.  相似文献   

13.
The South Jingyang Plateau, with a total area of 70 km2, is located in Shaanxi Province, China. Since 1976, more than 50 landslides of different types have occurred repeatedly on the edge slopes of the plateau due to the start of diversion irrigation on the plateau, resulting in great loss of lives and property. To better understand the initiation and movement mechanisms of these loess landslides, we surveyed them and carried out a detailed investigation of a large landslide in the Xihetan area. Our field survey results revealed that although most of these landslides had a long runout with high mobility, most of the landslide materials originating from the edge slopes may have been in an unsaturated state when the landslide occurred. This suggests that the materials at the toe of the edge slope as well as on the travel path along the river terrace might have played a key role in landslide movement. To examine how the materials on the travel path were involved in the landsliding, we used a multichannel surface wave technique and surveyed shear wave velocity (V s ) profiles of the landslide deposits. We also examined the internal geometry of the deposits that outcropped on the right-side slope of the landslide foot. The longitudinal profile of V s along the direction of movement showed that terrace deposits near the toe of the edge slope may have been sheared upward, indicating that at the toe, the surface of rupture might be located inside the terrace deposits. The V s contours showed an A-shaped fold within the landslide deposits in the middle part of the travel path and became greater in the most distal toe part. The V s profile across the deposits showed a U-shaped belt, in which the soil layers have smaller V s . This belt may be the boundary between the sliding landslide debris and terrace deposits. The observed internal geometry of the landslide deposits indicates that a sliding surface developed within the sandy layer underlying the gravel layer. Therefore, we inferred that after failure, the displaced landslide materials overrode and sheared the terrace deposits along its main sliding direction, resulting in the formation of thrust folds within the terrace deposits, and greater V s on the distal toe part of the landslide.  相似文献   

14.
We have used spectrograms taken with a dispersion of 8–12 Å per mm and Kurucz model atmospheres to study the supergiant 89 Her (F2Ibe).We find the effective temperature and gravity T eff = 6300 ± 150 K and log g = 0.5 ± 0.2. We have analyzed the microturbulence in the star’s atmosphere based on FeI, FeII, and TiII lines, deriving ξ t = 7.0 ± 0.5 km/s for the FeI and TiII lines and ξ t = 8.0 ± 0.5 km/s for the FeII lines. Abundances were determined for 23 elements. The elemental abundances in the atmosphere of 89 Her show deficiencies compared to the solar chemical composition, except for sodium, which is overabundant relative to the Sun.  相似文献   

15.
  相似文献   

16.
The results of hydrodynamical calculations of radially pulsating helium stars with masses 0.5M⊙≤M≤0.9M⊙, bolometric luminosities 600L⊙≤5×103L⊙, and effective temperatures 1.5×104 K≤Teff≤3.5×104 K are presented. The pulsation instability of these stars is due to the effects of ionization of iron-group elements in layers with temperatures T～2×105 K. The calculations were carried out using opacities for the relative mass abundances of hydrogen and heavy elements X=0 and Z=0.01, 0.015, and 0.02. Approximate formulas for the pulsation constant Q over the entire range of pulsation instability of the hot helium stars in terms of the mass M, radius R, effective temperature Teff, and heavy-element abundance Z are derived. The instability of BX Cir to radial pulsations with the observed period Π=0.1066 d occurs only for a mass M≥0.55M⊙, effective temperature Teff≥23000 K, and heavy-element abundance Z≥0.015. The allowed mass of BX Cir is in the range 0.55M⊙≤M≤0.8M⊙, which corresponds to luminosities 800L⊙≤M≤1400L⊙ and mean radii 1.7R⊙?R?2.1R⊙.  相似文献   

17.
Observations of eclipses of the radio pulsar B1259-63 by the disk of its Be-star companion SS 2883 provide an excellent opportunity to study the winds of stars of this type. The eclipses lead to variations in the radio flux (due to variations in the free-free absorption), dispersion measure, rotation measure, and linear polarization of the pulsar. We have carried out numerical modeling of the parameters of the Be-star wind and compared the results with observations. The analysis assumes that the Be-star wind has two components: a disk wind in the equatorial plane of the Be star with a power-law fall-off in the electron density n e with distance from the center of the star \(\rho (n_e \sim \rho ^{ - \beta _o } )\), and a spherical wind above the poles. The parameters for a disk model of the wind are estimated. The disk is thin (opening angle 7.5°) and dense (electron density at the stellar surface n0e ～ 1012 cm?3, β0 = 2.55). The spherical wind is weak (n0e ? 109 cm?3, β0 = 2). This is the first comparison of calculated and observed fluxes of the pulsating radio emission.  相似文献   

18.
Data quality control in geochemistry constitutes a fundamental problem that is still to be solved from the application of statistics and computation. We used refined Monte Carlo simulations of 10,000 replications and 190 independent experiments for sample sizes of 5 to 100. Statistical contaminations of 1 to 4 observations were used to compare 9 statistical parameters (4 central tendency—mean, median, trimean, and Gastwirth mean, and 5 dispersion estimates—standard deviation, median absolute deviation, S n , Q n , and \( {\widehat{\sigma}}_n \)). The presence of discordant observations in the data arrays rendered the outlier-based and robust parameters to disagree with each other. However, when the mean and standard deviation (outlier-based parameters) were estimated from censored data arrays obtained after the identification and separation of outlying observations, they generally provided a better estimate of the population than the robust estimates obtained from the original data arrays. This inference is contrary to the general belief, and therefore, reasons for the better performance of the outlier-based methods as compared to the robust methods are suggested. However, when all parameters were estimated from censored arrays and appropriate precise and accurate correction factors put forth in this work were applied, all of them became fully consistent, i.e., the mean agreed with the median, trimean and Gastwirth mean, and the standard deviation with the median absolute deviation, S n , Q n , and \( {\widehat{\sigma}}_n \). An example of inter-laboratory chemical data for a Hawaiian reference material BHVO-1 included sample sizes from 5 to 100, which showed that small samples of up to 20 provide inconsistent estimates, whereas larger samples of 20–100, especially >40, were more appropriate for estimating statistical parameters through robust or outlier-based methods. Although all statistical estimators provided consistent results, our simulation study shows that it is better to use the censored sample mean and population standard deviation as the best estimates.  相似文献   

19.
Diffusion couple experiments with wet half (up to 4.6 wt%) and dry half were carried out at 789–1,516 K and 0.47–1.42 GPa to investigate water diffusion in a peralkaline rhyolitic melt with major oxide concentrations matching Mount Changbai rhyolite. Combining data from this work and a related study, total water diffusivity in peralkaline rhyolitic melt can be expressed as:
$ D_{{{\text{H}}_{ 2} {\text{O}}_{\text{t}} }} = D_{{{\text{H}}_{ 2} {\text{O}}_{\text{m}} }} \left( {1 - \frac{0.5 - X}{{\sqrt {[4\exp (3110/T - 1.876) - 1](X - X^{2} ) + 0.25} }}} \right), $
$ {\text{with}}\;D_{{{\text{H}}_{ 2} {\text{O}}_{\text{m}} }} = \exp \left[ { - 1 2. 7 8 9- \frac{13939}{T} - 1229.6\frac{P}{T} + ( - 27.867 + \frac{60559}{T})X} \right], $
where D is in m2 s?1, T is the temperature in K, P is the pressure in GPa, and X is the mole fraction of water and calculated as X = (C/18.015)/(C/18.015 + (100 ? C)/33.14), where C is water content in wt%. We recommend this equation in modeling bubble growth and volcanic eruption dynamics in peralkaline rhyolitic eruptions, such as the ~1,000-ad eruption of Mount Changbai in North East China. Water diffusivities in peralkaline and metaluminous rhyolitic melts are comparable within a factor of 2, in contrast with the 1.0–2.6 orders of magnitude difference in viscosities. The decoupling of diffusivity of neutral molecular species from melt viscosity, i.e., the deviation from the inversely proportional relationship predicted by the Stokes–Einstein equation, might be attributed to the small size of H2O molecules. With distinct viscosities but similar diffusivity, bubble growth controlled by diffusion in peralkaline and metaluminous rhyolitic melts follows similar parabolic curves. However, at low confining pressure or low water content, viscosity plays a larger role and bubble growth rate in peralkaline rhyolitic melt is much faster than that in metaluminous rhyolite.
  相似文献   

20.
It is shown that the approximation of the complex, tidally distorted shape of a star as a circular disc with local line profiles and a linear limb-darkening law, which is usually applied when deriving equatorial stellar rotation velocities from line profiles, leads to overestimation of the equatorial velocity V rot sin i and underestimation of the component mass ratio q = M x /M v . A formula enabling correction of the effect of these simplifying assumptions on the shape of a star is used to re-determine the mass ratios q and the masses of the black holes M x and visual components M v in low-mass X-ray binary systems containing black holes. Taking into account the tidal–rotational distortion of the stellar shape can significantly increase the mass ratios q = M x /M v , reducing M v , while M x changes only slightly. The resulting distribution of M v attains its maximum near M v ? 0.35M ⊙, in disagreement with the results of population synthesis computations realizing standard models for Galactic X-ray novae with black holes. Possible ways to overcome this inconsistency are discussed. The derived distribution of M x also differs strongly from the mass distribution for massive stars in the Galaxy.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号