首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 343 毫秒
1.
Sassa and others in the Disaster Prevention Research Institute (DPRI), Kyoto University, developed a series of undrained ring-shear apparatus to physically simulate landslide initiation and motion, from DPRI-3 (Sassa 1992) to DPRI-7 (Sassa et al., Landslides 1(1):7–19, 2004). The maximum undrained capacities in the DPRI series ranged from 300 to 650 kPa. Sassa and others in the International Consortium on Landslides (ICL) have developed a new series of undrained ring-shear apparatus (ICL-1and ICL-2) for two projects of the International Programme on Landslides (IPL-161 and IPL-175). Both projects are supported by the Science and Technology Research Partnership for Sustainable Development Program (SATREPS) of Japan. ICL-1 was developed to create a compact and transportable apparatus for practical use in Croatia; one set was donated to Croatia in 2012. ICL-2 was developed in 2012–2013 to simulate the initiation and motion of megaslides of more than 100 m in thickness. The successful undrained capacity of ICL-2 is 3 MPa. This apparatus was applied to simulate possible conditions for the initiation and motion of the 1792 Unzen–Mayuyama megaslide (volume, 3.4?×?108 m3; maximum depth, 400 m) triggered by an earthquake. The megaslide and resulting tsunami killed about 15,000 people. The Unzen Restoration Office of the Ministry of Land, Infrastructure and Transport (MLIT) of Japan systematically collected various papers and reports and published two summary leaflets: one in English in 2002 and an extended version in Japanese in 2003. Samples were taken from the source area (for initiation) and the moving area (for motion). The hazard area was estimated by the integrated landslide simulation model LS-RAPID, using parameters obtained with the ICL-2 undrained ring-shear apparatus. The estimated hazard area agrees reasonably with the landslide moving area reported in the Ministry leaflets.  相似文献   

2.
The site investigation of low-gradient slopes composed by marly rocks usually focuses on shallow slides in weathered mantling material as it is assumed that the underlying bedrock has higher strength, but deeper investigations may reveal larger, active, deep-seated movements. A typical example of this is found in Montemartano (Perugia, Central Italy). Here aerial photo interpretation and field observations indicate that active movements involve the shallower portion of the slope, formed by a very old and large landslide body extending over an area of about 0.5 km2. Borehole core logging and probe inclinometer monitoring reveal that the area corresponding to the deep-seated landslide is moving at a maximum rate of 70 mm/year down to a maximum depth of 40 m. A comparison of inclinometer and piezometer data indicates that the movement seasonally reactivates even when rainfall and piezometer levels are below average values and suggests that structural setting of the whole slope influences both groundwater flow and movement kinematics. This hypothesis is reinforced by seepage analyses and stability analyses yielding a mobilized shear strength close to residual strength of the clayey interbeds of the marly limestone formations. This implies that instability occurs along bedding over a large part of the slide. The importance of these phenomena in land management policy is discussed and the critical aspects of their investigation and monitoring are addressed. The reconstruction of landslide geometry/stratigraphy and geotechnical characterization of the materials is closely considered, particularly as these are complicated by the limited representativeness of field and laboratory investigations in this type of material.  相似文献   

3.
在遥感解译、野外调查的基础上,采用高密度电法和电阻率测深法,并结合钻探对川西岷江河谷发育的尕米寺滑坡、俄寨村滑坡、格机寨滑坡等典型大型—巨型古滑坡的空间结构进行了勘探分析,有效确定了古滑坡的空间结构和滑带特征,并认为古滑坡的滑动面多具有高低阻相间的不稳定电性层,且滑坡前缘多位于不稳定电性层变薄收敛的地方。其中,俄寨村滑坡高低阻相间的不稳定电性层厚约0~45 m,为滑坡堆积层,古滑动面紧贴基岩面,滑动面平均埋深约30 m,弱风化基岩面埋深约5.6~61 m,强风化层厚约为3~12 m;尕米寺滑坡高低阻相间的不稳定电性层厚约2.5~43 m,为滑坡堆积层,沿剖面古滑动面平均埋深约35 m,在滑坡中部存在一圈闭的低阻异常体,推测为古河道,并与钻探结果相吻合,其埋深约56~96 m,弱风化基岩面埋深13.3~100 m,强风化及岩溶综合层厚一般约为5~20 m。基于古滑坡的地球物理勘探数据和解译结果,统计分析了川西岷江河谷地区大型—巨型古滑坡空间岩土体的地球物理物性参数,对指导该区滑坡调查分析具有重要的指导意义。  相似文献   

4.
Subaerial landslides falling into confined water bodies often generate impulsive waves. Damaging landslide tsunamis in Three Gorges Reservoir, China, have struck several times in the last 15 years. On June 24, 2015, a 23?×?104 m3 slope failure occurred on the east bank of the Daning River opposite Wushan Town. The sliding mass intruded into the Three Gorges Reservoir and initiated a reservoir tsunami that resulted in two deaths and significant damage to shipping facilities. A post-event survey revealed the landslide geometry and wave run-up distribution, while an eyewitness video captured most of the landslide motion. Employing these firm constraints, we applied the Tsunami Squares method to simulate the 2015 Hongyanzi landslide and tsunami. The simulation revealed that the landslide experienced a progressive failure in the first few seconds and impacted the water with a maximum velocity of ~?16 m/s. The initial wave propagated to the opposite shore in an arch shape, and the water surface reached a maximum amplitude of ~?11 m near the landslide. Wave amplitude-time curves at four points on the river cross section show that the initial wave reached Wushan town in about 50 s with an average wave velocity of ~?30 m/s. The maximum wave run-ups on the shoreline opposite the landslide are around 6 m and attenuate to less than 1 m beyond 2-km distance. The landslide simulation matches the observed geological profile and the eyewitness video, and the numerical results coincide with the observed wave run-up heights. Nearly 80% of landslide energy is lost due to frictional resistances, but the remaining fraction imparted to the tsunami carried catastrophic consequences to a large region. The numerical results emphasize the efficiency and accuracy of Tsunami Squares method for a “Quick Look” simulation of a potential landslide.  相似文献   

5.
On 11 January 2013, a catastrophic landslide of ～0.2 million m3 due to a prolonged low-intensity rainfall occurred in Zhenxiong, Yunnan, southwestern China. This landslide destroyed the village of Zhaojiagou and killed 46 people in the distal part of its path. The displaced landslide material traveled a horizontal distance of ～800 m with a vertical drop of ～280 m and stopped at 1520 m a.s.l. To examine the possible mechanism and behavior of the landslide from initiation to runout, the shear behavior of soil samples collected from the sliding surface and runout path was examined by means of ring shear tests. The test results show that the shear strength of sample from the sliding surface is less affected by shear rate while the shear rate has a negative effect on the shear strength of runout path material. It is suggested that the source and runout path materials follow the frictional and Voellmy rheology, respectively. Post-failure behavior of the landslide was modeled by using a DAN-W model, and the numerical results show that the selected rheological relationships and parameters based on the results of ring shear tests may provide good performance in modeling the Zhenxiong landslide.  相似文献   

6.
Every year, Australia experiences tropical cyclones that bring large amounts of rainfall, causing flooding and damage to infrastructure and road closure due to landslips. In March 2017, tropical cyclone Debbie hit the Queensland coast dumping 747 mm of rainfall within 2 days to the Gold Coast region. As a result, multiple shallow landslides occurred in Gold Coast and northern New South Wales due to the increase in soil saturation. A field investigation was conducted from several sites between Gold Coast-Springbrook road and Tallebudgera creek road to identify geological settings and landslide characteristics. Key findings show that slides predominantly occurred in weathered meta-sediments of the Neranleigh-Fernvale Beds within a depth of 1–2 m. Furthermore, a series of shear box tests revealed that the shear strength of the soil significantly decreased when saturation occurred.  相似文献   

7.
The 2008 Ms 8.0 Wenchuan earthquake triggered a large number of extensive landslides. It also affected geologic properties of the mountains such that large-scale landslides followed the earthquake, resulting in the formation of a disaster chain. On 10 July 2013, a catastrophic landslide–debris flow suddenly occurred in the Dujiangyan area of Sichuan Province in southeast China. This caused the deaths of 166 people and the burying or damage of 11 buildings along the runout path. The landslide involved the failure of ≈1.47 million m3, and the displaced material from the source area was ≈0.3 million m3. This landslide displayed shear failure at a high level under the effects of a rainstorm, which impacted and scraped an accumulated layer underneath and a heavily weathered rock layer during the release of potential and kinetic energies. The landslide body entrained a large volume of surface residual diluvial soil, and then moved downstream along a gully to produce a debris flow disaster. This was determined to be a typical landslide–debris flow disaster type. The runout of displaced material had a horizontal extent of 1200 m and a vertical extent of 400 m. This was equivalent to the angle of reach (fahrböschung angle) of 19° and covered an area of 0.2 km2. The background and motion of the landslide are described in this study. On the basis of the above analysis, dynamic simulation software (DAN3D) and rheological models were used to simulate the runout behavior of the displaced landslide materials in order to provide information for the hazard zonation of similar types of potential landslide–debris flows in southeast China following the Wenchuan earthquake. The simulation results of the Sanxicun landslide revealed that the frictional model had the best performance for the source area, while the Voellmy model was most suitable for the scraping and accumulation areas. The simulations estimated that the motion could last for ≈70 s, with a maximum speed of 47.7 m/s.  相似文献   

8.
Subsurface structures from two different districts of Istanbul, hosting waste and freshwater transmission lines, were imaged by geoelectrical method. The environmental impact on Ka??thane-Terkos freshwater transmission line is one of the issues. That waterline underwent a substantial landslide damage. The previous site selection of Ka??thane-Terkos line was only based on surface geological observations. Even though the pipeline was positioned away from the surface scarps of landslides, the pipes were damaged. To find out the reason, we made some vertical electrical sounding measurements using Schlumberger array in the region. We inverted the electrical sounding data using 2D inversion technique. The final geoelectrical images show main landslide failures, at about 10–30 m depth, which are overlain by debris with a resistivity value of with <6 Ω m. The geoelectrical findings reveal that a buried major failure surrounds the surface landslides behind. Consequently, the water infrastructure remains under the influence of landslide. Our second application site was the area of the Sazl?dere tunnel, which will transfer wastewater, polluting Sazl?dere dam, to the treatment plant. The geoelectrical images along Sazl?dere tunnel route show resistive (<100 Ω m) and moderately conductive (≤50 Ω m) structures along the tunnel axis, representing unaltered to highly weathered rocks, respectively. Furthermore, consecutive hidden fault zones which severely affect the construction process of the tunnel are detected and located.  相似文献   

9.
A calamitous landslide happened at 22:00 on September 1, 2014 in the Yunyang area of Chongqing City, southwest China, enforcing the evacuation of 508 people and damaging 23 buildings. The landslide volume comprised 1.44 million m3 of material in the source area and 0.4 million m3 of shoveled material. The debris flow runout extended 400 m vertically and 1600 m horizontally. The Xianchi reservoir landslide event has been investigated as follows: (1) samples collected from the main body of landslide were carried out using GCTS ring shear apparatus; (2) the parameters of shear and pore water pressure have been measured; and (3) the post-failure characteristics of landslide have been analyzed using the numerical simulation method. The excess pore-water pressure and erosion in the motion path are considered to be the key reasons for the long-runout motion and the scale-up of landslides, such as that at Xianchi, were caused by the heavy rainfall. The aim of this paper is to acquired numerical parameters and the basic resistance model, which is beneficial to improve simulation accuracy for hazard assessment for similar to potentially dangerous hillslopes in China and elsewhere.  相似文献   

10.
Tsaoling is located in Southwestern Taiwan, 10 km east of the frontal thrusts of the mountain belt. Five large historical landslide events were recorded from 1862 to 1999. No details of the earliest landslide event (1862) are available, thus this paper deals with the 1941 landslide event. Using the Particle Flow Code in two dimensions (PFC 2D) to simulate the mechanism of the Tsaoling landslide in 1941, this study shows that the landslide block developed cracks and slid down 0.2–1.8 m on the sliding plane. The cracks concentrated in certain zones, which corresponded to future landslide detachment planes. During the vibration simulation, the cracks spread from the shear plane to ground surface. Monitoring the variations of the displacements, velocity, and stress during vibration simulation showed that the peak velocity and stress in the transition zones occurred at 3 s. The displacement of the left part of the block exceeded 1.3 m, and the displacement of the right part was less than 1.3 m during vibration simulation. These results suggest that the left part of the block was pushed down by the right part, ultimately inducing a landslide during an earthquake.  相似文献   

11.
Frequent failures of monsoons have forced to opt the groundwater as the only source of irrigation in non-command areas. Groundwater exploration in granitic terrain of dry land agriculture has been a major concern for farmers and water resource authorities. The hydrogeological complexities and lack of understanding of the aquifer systems have resulted in the failure of a majority of the borehole drillings in India. Hence, a combination of geophysical tools comprising ground-penetrating radar (GPR), multielectrode resistivity imaging (MERI), and vertical electrical sounding (VES) has been employed for pinpointing the groundwater potential zones in dry land agricultural of granitic terrain in India. Results obtained and verified with each other led to the detection of a saturated fracture within the environs. In GPR scanning, a 40-MHz antenna is used with specifications of 5 dielectric constant, 600 scans/nS, and 40 m depth. The anomalies acquired on GPR scans at various depths are confirmed with low-resistivity ranges of 27–50?Ω m at 23 and 27 m depths obtained from the MERI. Further, drilling with a down-the-hole hammer was carried out at two recommended sites down to 50–70 m depth, which were complimentary of VES results. The integrated geophysical anomalies have good agreement with the drilling lithologs validating the MERI and GPR data. The yields of these bore wells varied from 83 to 130 l/min. This approach is possible and can be replicated by water resource authorities in thrust areas of dry land environs of hard rock terrain around the world.  相似文献   

12.
A rock avalanche is a geological event that is always sudden, rapid and with a long run-out, and can result in large loss of lives and property. The Wenjiagou rock avalanche was a high-speed rock landslide caused by a strong earthquake, in Mianzhu, Sichuan Province, southwest China. In this study, we reproduce the movement and deposition processes of the sliding mass by numerical simulation. We analyze the effects of the friction coefficient of each slip surface and the strength of the parallel bonds and contact stiffness between particles on the dynamic process and deposit features using three-dimensional particle flow code (PFC3D). The simulation results agree with the field measurements when the friction coefficient is 0.2, parallel bond strength is 2 MPa, and contact stiffness is 2?×?108 kN/m. The landslide lasted about 115 s from the initial movement to the final deposition at the exit of the valley. The maximum velocity of the sliding mass was 114 m/s.  相似文献   

13.
风化岩体中压力型锚索锚固段的剪应力分析   总被引：1，自引：0，他引：1  
夏元友  叶红  刘笑合  陈杰 《岩土力学》2010,31(12):3861-3866
岩体在风化过程中,其物理力学性质会随着风化程度的不同有所差异。结合均质岩体中压力型锚索受力特点,以及内部对称荷载作用下横观各向同性弹性体内的剪应力分布特点,推导出了压力型锚索在横观各向同性弹性岩体内的剪应力分布方程。假定风化岩体为横观各向同性弹性体,其弹性模量及剪切模量均按指数函数变化,分析结果表明：①由于风化岩体的弹性模量随着深度的变化,锚索锚固段的剪应力也随着岩体的弹性模量的增加（减小）而增加（减小）;②在承压板附近,锚索锚固段的剪应力随锚索孔半径的增加而减小,由于风化岩体剪切模量的变化,因而导致剪应力的变化量很大;③在承压板附近,锚索锚固段接触面上的剪应力随着垂直于岩体横向等向面的剪切模量的改变而相应的改变。研究成果可为实际工程中压力型锚索设计提供参考。  相似文献   

14.
This study analyzes the mechanism of the landslide event at Hsiaolin Village during Typhoon Morakot in 2009. This landslide event resulted in 400 deaths. The extremely high intensity and accumulative rainfall events may cause large-scale and complex landslide disasters. To study and understand a landslide event, a combination of field investigations and numerical models is used. The landslide area is determined by comparing topographic information from before and after the event. Physiographic parameters are determined from field investigations. These parameters are applied to a numerical model to simulate the landslide process. Due to the high intensity of the rainfall event, 1,675 mm during the 80 h before the landslide event, the water content of soil was rapidly increased causing a landslide to occur. According to the survivors, the total duration of the landslide run out was less than 3 min. Simulation results indicated that the total duration was about 150 s. After the landslide occurrence, the landslide mass separated into two parts by a spur at EL 590 in about 30 to 50 s. One part passed the spur in about 30 to 60 s. One part inundated the Hsiaolin Village and the other deposited at a local river channel and formed a landslide dam. The landslide dam had height between 50 and 60 m and length between 800 and 900 m. The simulation result shows that the proposed model can be used to evaluate the potential areas of landslides induced by extremely high intensity rainfall events.  相似文献   

15.
An investigation of excess pore-pressure generation of a weathered granitic sand, taken from the source area of a typical landslide caused as a result of liquefaction, and a fine silica sand was conducted, in which grain crushing within the shear zone of ring-shear test specimens was examined as the key phenomenon of rapid long-runout motion of landslides. In order to investigate and explain the low average apparent-friction angle, mobilized in a liquidized landslide, speed-controlled ring-shear tests were conducted under undrained conditions on weathered granitic-sand specimens, formed under a wide range of initial void ratios. It was revealed that very small steady-state shear resistances were obtained irrespective of the initial void ratios, which can explain the low average apparent-friction angle. In addition, two series of ring-shear tests on weathered-granitic and fine-silica sands were conducted under naturally drained conditions by keeping the upper drain valve of the shear box open during the tests. The first series of tests was performed under differing total normal stresses, but at the same shear speed, and the second series was conducted at differing shear speeds, but under the same total normal stress. In order to investigate and analyze excess pore-pressure generation and dissipation within the shear zone that is associated with grain crushing, permeability analyses were conducted by passing water through the sample box of the ring-shear test apparatus before and after shearing. In addition, grain-size distribution analyses of samples taken from the shear zone after shearing were carried out. For the weathered granitic-sand samples, a significant change in bulk permeability and large amount of grain crushing were observed. In these tests on the above soil, a considerable reduction of shear resistance, which increased proportionally to the total normal stress and shear speed, were obtained. It was observed that due to grain crushing, finer grains that lowered the permeability of the soil in the shear zone, were formed. It is likely that the decrease in permeability facilitated the generation of high excess pore pressures by reducing the pore-pressure dissipation rate from the shear zone; thus, flow behaviour was exhibited even under naturally drained conditions.  相似文献   

16.
  相似文献   

17.
The Daguangbao landslide is the largest co-seismic landslide triggered by the Wenchuan earthquake (Ms 8.0) occurred on 12 May 2008. The landslide, which is 4.6 km long and 3.7 km wide, involves a volume of approximately 1.2 × 109 m3. An exposed slip surface, situated at the southern flank of its source area, was observed with a length of 1.8 km along the main sliding direction and an area of 0.3 km2. To study the geological and tectonic characteristics of the source area and their contributions to the landslide formation during the earthquake, detailed geological investigations were firstly conducted. And it is reached that the landslide occurred on the northwestern limb of the Dashuizha anticline with its scarp showing several geological structures, including joint sets, local faults, and folds. These tectonic-related structures potentially influenced the failure of the landslide. Secondly, further investigations were focused on the inclined planar sliding surface using 12 exploratory trenches, nine boreholes, a tunnel, borehole sonic data, and micro-images. These data reveal that the rock mass along the sliding surface was the fragmented rock of a bedding fault. A pulverized zone was observed on the sliding surface, which was the zone of shear localization during the landslide. This suggests that the shear failure of the Daguangbao landslide developed within the bedding fault. The rapid failure of the landslide was associated with the degradation of the rock mass strength of the bedding fault both before and during the 2008 Wenchuan earthquake. With this study, we propose that a pre-existing large discontinuity within a slope may be the basis for initiating a large landslide during earthquake.  相似文献   

18.
This study investigates the causes and failure mechanism of the Aksu landslide that occurred during the construction of the Giresun–Espiye road between KM: 1 + 030–1 + 170 in northern Turkey and recommends proper stabilization techniques. For the purpose of investigating the causes and mechanism of this slope failure, engineering geological mapping, geotechnical investigation and rock mass characterization were performed. From top to bottom, weathered tuffite, tuffite, flysch, and dacitic tuffite were the major units in the study area. The disturbance of the slope by the excavations performed at the toe of the slope (i.e., due to the foundation excavation for the Tünel restaurant building and for the road cut) led to a “translational slide”. The “translational slide” occurred in completely weathered tuffite due to the disturbance of the stability of the slope by the excavations performed at the toe of the slope, particularly for the foundation excavation of the Tünel restaurant building and for the road cut along the Giresun–Espiye road. The rise in the groundwater level was also another important factor that has contributed to the occurrence of the landslide. After establishing the geometry of the landslide in detail, the shear strength parameters of the failure surface were determined by the back analysis method. Sensitivity analyses were performed and landslide failure mechanisms were modeled to quantify the contributing factors that have caused the formation of the Aksu landslide. The influence of an earthquake was investigated through pseudostatic slope stability analysis. Toe buttressing, ground water drainage, and surface water drainage alternatives were considered for stabilizing the slope.  相似文献   

19.
The effectiveness of inversion apparent resistivity data to determine accurately the true resistivity distribution over 2D structures has been investigated using a common inversion scheme based on smoothness-constrained nonlinear least-squares optimization with enhancing horizontal resolution (EHR) technique by numerical simulation. The theoretical model generates in RES2DMOD software at specific distance and depth using Wenner, Wenner–Schlumberger, and pole–dipole arrays were inverted. The inversion model was compared with the original 2D model in RES2DINV software. The study model includes horizontal layering, vertical resolution, and horizontal two layers with different resistivity. Also, the response to variations in data density of these arrays was investigated. The study shows the best array suitable to be used in the survey was chosen for real data acquisition at the actual site. Subsequently, the results from borehole were used to verify the results of 2D resistivity imaging method with and without EHR technique. Saturated zone (0–40 Ω-m) was found scattered at the depth of 10–20 m. The borehole is located at 63 m at 2D resistivity imaging survey which shows at depth 10–20 m is sandy silt. Highly weathered sandstone was found at 6 m depth with resistivity value of 800 Ω-m and SPT N value of 20. The bedrock was found at 27 m depth with resistivity value of 3,000 Ω-m and SPT N value of 50. The application of 2D resistivity imaging with EHR technique indicate the ability of the proposed approach in terms of density, depth, and resistivity value of anomalous and layer in a computationally and numerically efficient manner and to exhibit good performance in the data inversion.  相似文献   

20.
The groundwater in the karst region of northeastern Vietnam is found in various structural zones such as the Ha Lang, Song Hien, Hon Gai, Song Lo, Song Gam, and Hoang Lien Son Zones, etc. Results from this study show that groundwater in this region is at different depths: ~120 m deep at Quang Ninh, ~100 m at Lang Son, ~80 m at Cao Bang (The most water-abundant depth observed at Cao Bang varies from 40 to 45 m) while it varies from 18–25 to 80 m deep at Quan Ba (Ha Giang), especially at Meo Vac (Ha Giang), where groundwater is observed at 700–800 m deep (equivalent to local base level of the Nho Que River). Overall, groundwater in the region is fresh with total minerals varying from 250 to 400 mg/l; except for the coastal area of Quang Ninh, where groundwater is characterized by much higher total minerals (M = 3–18 g/l) due to the mixing with the saline sea water. The chemistry of water in the region demonstrates that the water is mainly bicarbonate with a [HCO3 ?] concentration varying from 150 to 265 mg/l, pH is of 6.5–8.1, and its hardness is of 3.7–6.0 meq/l.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号