首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 156 毫秒
1.
提出了一种基于经验模态分解(EMD)对载波相位测量进行周跳探测的新方法.利用非差和双差组成检验量,对采样率分别为1 S和30 S的观测值进行周跳探测,并与小波分析法进行对比.实验表明,经验模态分解法对于10周以内的周跳探测可以取得满意的效果.相对于小波分析法探测周跳,经验模态分解可以做到自适应.解决了由于小波基的选取不当对周跳探测结果的影响.并且进一步分析了EMD的端点效应对周跳探测的影响.  相似文献   

2.
详细概述了GPS周跳产生的原因及其探测周跳的重要性.利用小波分析方法对常用的GPS周跳检测量进行了周跳探测,并将结果与其他常规周跳探测方法进行了比较.通过实际数据测试,结果表明,采用bior3.1进行周跳探测并以电离层残差与宽巷载波减窄巷伪距的值作为检测值可以精确修复各频段上周跳,具有实际工程应用意义.  相似文献   

3.
利用改进的TurboEdit算法与Chebyshev多项式探测与修复周跳   总被引:1,自引:0,他引:1  
根据利用TurboEdit方法对GPS观测数据进行周跳探测的特点,设计了固定弧段长度的滑动窗口拟合模型,对其中的Geometry-Free组合法进行改进;在探测出周跳后,利用最小二乘Chebyshev多项式拟合来修复周跳。实验结果表明,改进后的TurboEdit算法可以探测出等周的1周小周跳、等周的大周跳和连续的小周跳、大周跳,同时,最小二乘Chebyshev多项式拟合可以精确修复以上周跳对。  相似文献   

4.
准确探测周跳并进行修复是提高北斗系统导航定位精度的核心问题之一,针对电离层残差法可以高效地探测小周跳但却无法修复周跳与无法正常探测出某些特定组合的周跳,以及多普勒积分法并不完全适用于北斗系统高轨卫星的周跳探测与修复等缺陷,提出了基于电离层残差法和多普勒积分联合探测修复周跳的方法,并应用实测数据进行了算例验证。  相似文献   

5.
基于小波变换的周跳探测与修复   总被引:2,自引:1,他引:1  
探测和修复周跳一直是GPS定位中的关键问题。利用小波变换对相位减伪距观测量进行周跳探测。首先介绍小波变换周跳探测的一般方法,然后在此基础上提出改进。改进方法可以对周跳进行探测和直接修复,进而探测和修复多次周跳,同时有效地克服一般方法可能出现探测失误的缺点。这种改进方法的效果在实验中得到验证。  相似文献   

6.
随着GPS广泛应用于高精度定位测量,周跳探测已经成为GPS研究的热点。针对双频载波观测值的特点,通过相邻历元的相位观测值求差来探测周跳,并通过实例证明该方法可以有效地进行周跳探测。  相似文献   

7.
为了准确地探测和确定GPS/GLONASS周跳并且提高小周跳探测和修复的能力,综合电离层残差法和相位减伪距法,提出了一种新的GPS/GLONASS周跳探测和确定方案:采用电离层残差法探测出周跳;由相位减伪距法确定周跳数的搜索范围;根据搜索范围组合出所有周跳数的候选值;最后,由电离层残差法检验量与其观测噪声最为接近的候选值为最佳的周跳值。采用该方案对江苏CORS和青岛CORS部分基准站观测数据进行处理分析。结果表明:该方法具备探测和确定小周跳的能力,其搜索的成功率在95%,探测分辨率可以达到0.03周,且修复精度可以达到±0.031周。  相似文献   

8.
影响周跳探测完整性的关键问题就是不敏感周跳的探测。针对这个问题,本文详细阐述了周跳探测在空间几何中的含义,包括组合系数的类型和数量与探测不敏感周跳之间的几何关系。依据空间几何原理的分析和尽可能减少不敏感周跳数据的要求,采用两个无几何相位组合和一个MW(MelbourneWbbena)组合构成周跳检验量。最后利用北斗三频实测数据对本文算法的正确性和可靠性进行验证计算。计算结果说明:本文算法具有较强的周跳探测修复能力,可以有效地避免不敏感周跳对探测结果的影响。  相似文献   

9.
针对山基GPS掩星观测值历元多、采用常规周跳探测方法不能快速探测周跳值的情况,提出首先利用三差法探测与修复大周跳,再利用Vondrak法探测与修复小周跳。试验证明,将两种方法相结合可以增加探测与修复周跳的效率。  相似文献   

10.
几种周跳探测方法在COMPASS数据预处理中的应用   总被引:1,自引:0,他引:1  
周跳探测一直是数据预处理中的关键问题,文中介绍高次差法、电离层残差法、M—W组合法进行周跳探测的原理及实现方法,并利用COMPASS监测站实测数据进行周跳探测试验,对周跳发生前后检验序列的变化做对比,结果表明,以上各方法可以准确、高效地检测出COMPASS载波相位观测量中的周跳。  相似文献   

11.
The difficulty to detect and repair cycle slip of carrier phase measurements is a key limit for continuously high accuracy of GNSS positioning and navigation services. We propose an automated cycle slip detection and repair method for data preprocessing of a CORS network. The method jointly uses double-differenced (DD) geometry-free (GF) combination and ionospheric-free observation corrected for the computed geometrical distance (IF-OMC) to estimate the cycle slips in dual-frequency observations. The DD GF combination, which is only affected by the ionospheric residual, can be used to detect cycle slips with high reliability except for special pairs such as (77, 60) on GPS L1/L2 frequencies. The detection principle of the IF-OMC observable is such that there is a large discontinuity related to the previous epoch when cycle slips occur at the present epoch. The disadvantages of these two combinations can be overcome employing the proposed detection method. The cycle slip pair (77, 60) has no effect on the GF combination, while a change of 14.65 m is derived from GPS L1/L2 observations using the IF-OMC algorithm. Using pre-determined station coordinates as precise values, we found that the accuracy of the DD IF-OMC combination was 18 mm for a 200-km CORS baseline. Therefore, cycle slips in dual-frequency observations can be correctly and uniquely determined using DD GF and IF-OMC equations. The proposed method was verified by adding simulated cycle slips in observations collected from the CORS network under a quiet ionosphere and shown to be effective. Moreover, the method was assessed with observations made during intense ionospheric activity, which generated extensive cycle slips. The results show that the algorithm can detect and repair all cycle slips apart from two exceptions relating to long data gaps.  相似文献   

12.
徐园  杨力  耿彦龙 《测绘工程》2012,21(3):49-52
随着GPS现代化、伽利略计划和Compass的建立,多频载波相位的研究已是一个热点方向。利用模拟的GPS多频数据通过多频载波/伪距数据组合进行周跳探测和修复,并对模拟的L5数据进行检验。实验结果表明,文中方法不仅对一系列的大周跳具有良好的探测和修复效果,对小周跳的探测和修复也很理想。  相似文献   

13.
随着GPS现代化的实施和L5频率的开设,GPS进入了三频时代。相对于双频观测数据三频观测值线性组合可以形成更多长波长、弱电离层、低噪声的组合。本文分析了GPS三频无几何相位组合的特性,利用两个GPS三频无几何相位组合和一个三频伪距载波组合组成观测矩阵探测周跳,并采用搜索方法确保周跳修复的正确。最后利用模拟的L5观测数据进行验证,结果表明该算法可以有效地探测并修复周跳。  相似文献   

14.
针对典型周跳探测与修复方法中的电离层残差法当同一历元多个频点发生周跳时,无法准确探测及修复周跳的问题,提出了一种用多普勒辅助电离层残差法的周跳探测与修复的改进方法。基于实测及仿真数据,证明了该方法能够有效解决电离层残差法存在的上述问题,即使某一历元多个频点同时发生周跳,也可以准确探测周跳发生的位置、频点及相应数值,精度达到1周,有效提高了电离层残差法探测与修复周跳的准确性与可靠性。  相似文献   

15.
周跳探测与修复是星载GPS数据预处理的重要内容。首先使用SWARM卫星实测数据对TurboEdit算法的有效性进行了分析,针对算法在观测噪声较大情况下无法有效探测小周跳的问题,提出了一种改进算法。该算法利用载波相位观测值对伪距组合观测值进行平滑,降低了观测噪声对宽巷模糊度的影响,提高了周跳探测能力。实验结果表明,改进算法能够有效提高小周跳的探测能力。   相似文献   

16.
Cycle slip detection and repair is an important issue in the GPS data processing. Different methods have been developed to detect and repair cycle slips on undifferenced , single- or double-differenced observations. The issue is still crucial for high-precision GPS positioning, especially for the undifferenced GPS observations. A method is proposed to fix cycle slips based on the generalized likelihood ratio (GLR) test. The method has a good performance on cycle slip fixing of undifferenced carrier phase observations on individual frequencies, either on L1 or on L2, without making a linear combination among the observables. The functional model is a piecewise cubic curve fitted to a number of consecutive data using the least squares cubic spline approximation (LS-CSA). For fixing the cycle slips, an integer estimation technique is employed to determine the integer values from the float solution. The performance of the proposed method is then compared with the existing two methods using simulated data. The results on a few GPS data sets with sampling rate of 1 Hz or higher confirm that this method can detect and correct all simulated cycle slips regardless of the size of the cycle slip or the satellite elevation angle. The efficacy of the method is then investigated on the GPS data sets with lower sampling rates of 5, 10, and 30 s. The results indicate that the proposed method always performs the best for the data sets considered. This is thus an appropriate method for cycle slip detection and repair of single-frequency GPS observations.  相似文献   

17.
This paper develops a new automated cycle slip detection and repair method that is based on only one single dual-frequency GPS receiver. This method jointly uses the ionospheric total electron contents (TEC) rate (TECR) and Melbourne–Wübbena wide lane (MWWL) linear combination to uniquely determine the cycle slip on both L1 and L2 frequencies. The cycle slips are inferred from the information of ionospheric physical TECR and MWWL ambiguity at the current epoch and that at the previous epoch. The principle of this method is that when there are cycle slips, the MWWL ambiguity will change and the ionospheric TECR will usually be significantly amplified, the part of artificial TECR (caused by cycle slips) being significantly larger than the normal physical TECR. The TECR is calculated based on the dual-frequency carrier phase measurements, and it is highly accurate. We calculate the ionospheric change information (including TECR and TEC acceleration) using the previous epochs (30 epochs in this study) and use the previous data to predict the TECR for the epoch needing cycle slip detection. If the discrepancy is larger than our defined threshold 0.15 TECU/s, cycle slips are regarded to exist at that epoch. The key rational of method is that during a short period (1.0 s in this study) the TECR of physical ionospheric phenomenon will not exceed the threshold. This new algorithm is tested with eight different datasets (including one spaceborne GPS dataset), and the results show that the method can detect and correctly repair almost any cycle slips even under very high level of ionospheric activities (with an average Kp index 7.6 on 31 March 2001). The only exception of a few detected but incorrectly repaired cycle slip is due to a sudden increased pseudorange error on a single satellite (PRN7) under very active ionosphere on 31 March 2001. This method requires dual-frequency carrier phase and pseudorange data from only one single GPS receiver. The other requirement is that the GPS data rate ideally is 1 Hz or higher in order to detect small cycle slips. It is suitable for many applications where one single receiver is used, e.g. real-time kinematic rover station and precise point positioning. An important feature of this method is that it performs cycle slip detection and repair on a satellite-by-satellite basis; thus, the cycle slip detection and repair for each satellite are completely independent and not affected by the data of other satellites.  相似文献   

18.
由于卫星信号被遮挡、低信噪比或接收机运动等原因,载波相位观测值较正常值会发生周跳。为解决这一问题,基于精密单点定位与惯导组合系统,提出了一种有效的惯导辅助周跳探测与修复方法。该方法基于无电离层(ionospheric free,IF)组合与宽巷(wide lane,WL)组合,利用惯导短时高精度信息代替伪距消除站星几何距离,结合历元间差、星间差等建立惯导辅助的IF组合模型和惯导辅助的WL组合模型。惯导辅助的IF组合模型不受电离层延迟影响,但无法探测特殊比例周跳,惯导辅助的WL组合模型波长较长,却无法探测双频等周周跳,两者的综合使用实现了优势互补。实验结果表明,该方法不仅能有效探测出各种大、小、双频等周和特殊比例周跳,而且在一定卫星信号中断时间内能实现周跳瞬时校正。  相似文献   

19.
三频GNSS电离层周跳处理   总被引:1,自引:0,他引:1  
在分析三频无几何无电离层组合特性的基础上,构造了3个线性无关的三频无几何无电离层组合作为周跳探测检验量,以解决电离层延迟活跃期时的周跳处理问题。为保证周跳修复的准确性,提出采用两次历元差分后的电离层残差值对周跳修复值进行验证与确认。通过高电离层延迟条件下的三频观测数据对本文算法进行了验证分析。试验结果表明,该方法可实现高电离层延迟条件下对周跳的探测与修复,并可适用于三频实时、非差导航定位的周跳处理。  相似文献   

20.
针对传统码-载波相位周跳探测方法应用于单频RTK时,存在的对小周跳不敏感、易受码观测噪声的影响等问题,本文提出一种多普勒观测值辅助的单频周跳探测方法。该方法将连续两个相邻历元多普勒观测值与载波相位差分观测值相结合,以构造实时周跳探测的多普勒-载波相位差分序列。然后应用假设检验方法,检测单频载波相位观测值是否存在周跳。实测数据分析表明:本文提出的方法能够准确探测单频载波相位观测数据中的小周跳,且该方法对周跳探测的灵敏度比传统码-相位差分序列方法更高,适用于单频RTK定位技术。   相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号