共查询到20条相似文献，搜索用时 358 毫秒
1.
通过模型试验研究了竖向荷载作用下砂土中斜桩的荷载传递性状,分析了桩身倾角及长径比对斜桩桩身轴力、弯矩、剪力、桩侧摩阻力及端阻比的影响。试验结果表明：在桩顶竖向荷载作用下,斜桩桩身轴力均小于相应直桩桩身轴力,桩身倾角越大,轴力沿深度衰减得越快,桩长径比越大,轴力沿深度衰减得也越快;斜桩桩身最大弯矩随桩身倾角及长径比的增加而增加,最大弯矩出现的深度与桩身倾角无关,只与长径比相关;不论桩身倾角及长径比的大小,斜桩桩身最大剪力均出现在桩顶截面处,桩身最大剪力随着桩身倾角的增加而增大;桩身倾角越大,斜桩最大摩阻力越大,长径比越大,斜桩最大摩阻力越小,斜桩最大摩阻力出现在桩顶下1/4～1/5桩长处;斜桩端阻比随着桩顶竖向荷载的增加而增大,随着桩身倾角及长径比的增加而减小。 相似文献
2.
A hypoplastic macroelement for single vertical piles in sand subject to three-dimensional loading conditions 总被引：2，自引：2，他引：0
This paper presents a novel macroelement for single vertical piles in sand developed within the hypo-plasticity theory, where the incremental nonlinear constitutive equations are defined in terms of generalized forces, displacements and rotations. Inspired from the macroelement for shallow foundations of Salciarini and Tamagnini (Acta Geotech, 4(3):163–176, 2009), the new element adopts the “intergranular displacement” mutuated from Niemunis and Herle (Mech Cohes Frict Mater, 2:279–299, 1997) to reproduce the behavior under cyclic loading. Analytical and numerical strategies are provided to calibrate the macroelement’s parameters. Comparisons with experimental results show the performance of the macroelement that while being simple and computational fast is suitable for finite element calculations and engineering design. 相似文献
3.
To a practicing foundation engineer, the performance of batter pile under seismic conditions still remains a questionable prospect. The contradictory findings reported by various investigators with regard to the performance of batter piles add to this dilemma. This calls for a rigorous three-dimensional investigation to evaluate seismic behavior of batter pile groups. In this study, a comparative assessment of three-dimensional seismic behavior of a 2 × 2 vertical and batter pile groups having batter angle of 15° was carried out using a full three-dimensional finite element code developed in MATLAB (Sarkar 2009). The effects of centre to centre spacing of piles and soil modulus values were investigated. Idealized soil profiles having constant and triangular variation of soil modulus were adopted for the study. Results of analyses for both the vertical and batter pile groups are presented in terms of dynamic stiffness and kinematic interaction factors. Results indicate better seismic performance of batter pile groups in comparison to that of vertical pile groups. To demonstrate the importance of the findings, a five-storied portal frame structure supported separately on vertical and batter pile groups were considered and analyzed for El-Centro Earthquake (1940) time history. The difference in structural response considering vertical and batter pile groups is highlighted. 相似文献
4.
This article derives the closed‐form solutions for estimating the vertical surface displacements of cross‐anisotropic media due to various loading types of batter piles. The loading types include an embedded point load for an end‐bearing pile, uniform skin friction, and linear variation of skin friction for a friction pile. The planes of cross‐anisotropy are assumed to be parallel to the horizontal ground surface. The proposed solutions are never mentioned in literature and can be developed from Wang and Liao's solutions for a horizontal and vertical point load embedded in the cross‐anisotropic half‐space. The present solutions are identical with Wang's solutions when batter angle equals to 0°. In addition, the solutions indicate that the surface displacements in cross‐anisotropic media are influenced by the type and degree of material anisotropy, angle of inclination, and loading types. An illustrative example is given at the end of this article to investigate the effect of the type and degree of soil anisotropy (E/E′, G′/E′, and ν/ν′), pile inclination (α), and different loading types (a point load, a uniform skin friction, and a linear variation of skin friction) on vertical surface displacements. Results show that the displacements accounted for pile batter are quite different from those estimated from plumb piles, both driven in cross‐anisotropic media. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
5.
This work presents analytical solutions to compute the vertical stresses for a cross‐anisotropic half‐space due to various loading types by batter piles. The loading types are an embedded point load for an end‐bearing pile, uniform skin friction, and linear variation of skin friction for a friction pile. The cross‐anisotropic planes are parallel to the horizontal ground surface. The proposed solutions can be obtained by utilizing Wang and Liao's solutions for a horizontal and vertical point load acting in the interior of a cross‐anisotropic medium. The derived cross‐anisotropic solutions using a limiting approach are in perfect agreement with the isotropic solutions of Ramiah and Chickanagappa with the consideration of pile inclination. Additionally, the present solutions are identical to the cross‐anisotropic solutions by Wang for the batter angle equals to 0. The influential factors in yielded solutions include the type and degree of geomaterial anisotropy, pile inclination, and distinct loading types. An example is illustrated to clarify the effect of aforementioned factors on the vertical stresses. The parametric results reveal that the stresses considering the geomaterial anisotropy and pile batter differ from those of previous isotropic and cross‐anisotropic solutions. Hence, it is imperative to take the pile inclination into account when piles are required to transmit both the axial and lateral loads in the cross‐anisotropic media. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
6.
Goit Chandra Shekhar Saitoh Masato Igarashi Takumi Sasaki Shun 《Acta Geotechnica》2021,16(4):1231-1245
Physical-scaled model testing under 1 g conditions is carried out in obtaining the vertical response of fixed head floating-inclined single piles embedded in dry sand. Practical pile inclinations of 5° and 10° besides a vertical pile (0°) subjected to static and dynamic vertical pile head loadings are considered. To account for the effects of soil nonlinearity as well as the soil–pile interface nonlinearity on the response of piles, a range of low-to-high magnitude of pile head displacements is considered for the static case while a varying amplitude of harmonic accelerations for a wide range of frequencies is considered for the dynamic case. Experimental results are obtained in the form of pile head stiffnesses and strains generated in the pile under both the static and dynamic loadings. Results suggest that the nonlinear behavior of soil as well as the nonlinearity generated at the interface between the soil and the pile as the result of applied loading considerably affect the response of piles. The soil–pile interface nonlinearity that governs the slippage of pile shows a clear influence on the pile head stiffnesses by providing two distinct values of stiffnesses corresponding to the push and the pull directional movement of piles; the two values are significantly different. Axial and bending strains generated in the piles show expected dependency on the amplitude of applied loading; the pile head-level bending strain increases almost linearly with the increase in the angle of pile inclination.
相似文献7.
This paper presents a numerical formulation of a three dimensional embedded beam element for the modeling of piles, which incorporates an explicit interaction surface between soil and pile. The formulation is herein implemented for lateral loading of piles but is able to represent soil–pile interaction phenomena in a general manner for different types of loading conditions or ground movements. The model assumes perfect adherence between beam and soil along the interaction surface. The paper presents a comparison of the results obtained by means of the present formulation and by means of a previously formulated embedded pile element without interaction surface, as well as reference semi‐analytical solutions and a fully 3D finite element (FE) model. It is seen that the proposed embedded element provides a better convergence behavior than a previously formulated embedded element and is able to reproduce key features of a full 3D FE model. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
8.
The geothermal use of concrete geostructures (piles, walls and slabs) is an environmentally friendly way of cooling and heating buildings. With such geothermal structures, it is possible to transfer energy from the ground to fluid‐filled pipes cast in concrete and then to building environments. To improve the knowledge in the field of geothermal structures, the behaviour of a pile subjected to thermo‐mechanical loads is studied in situ. The aim is to study the increased loads on pile due to thermal effects. The maximum thermal increment applied to the pile is on the order of 21°C and the mechanical load reached 1300 kN. Coupled multi‐physical finite element modelling is carried out to simulate the observed experimental results. It is shown that the numerical model is able to reproduce the most significant thermo‐mechanical effects. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
9.
This paper presents a three‐dimensional finite element analysis of the response of battered piles to the combined lateral and vertical pullout loads. Analyses are carried out using an elastoplastic constitutive law based on the non‐associated Mohr–Coulomb criterion. The influence of the contact condition at the pile–soil interface is also investigated. Analyses show that the load's inclination with regard to the pile's axis affects both the lateral and axial response of the battered piles. Analyses also show that the pullout capacity of battered piles is affected by the pile's inclination regarding the vertical axis as well as the load's inclination regarding the pile's axis. The investigation of the influence of the contact condition at the soil–pile interface shows that the possibility of sliding at the soil–pile interface affects the response of battered piles subjected to loads with low inclination regarding the pile's axis. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
10.
砂土地基斜桩水平承载特性p-y曲线法 总被引：2，自引：0，他引：2
基于Reese建议的砂土p-y曲线,提出了适用于斜桩水平承载特性分析的修正p-y曲线及相应的有限元分析方法。根据桩前土体受力特点,假设桩前浅层土体达到极限破坏状态时桩侧被动破坏区为一个三维楔形体,采用极限平衡分析方法导出了斜桩桩侧极限土抗力表达式,对比研究了斜桩倾角、桩-土界面摩擦系数等因素对极限土抗力的影响规律,并给出了斜桩初始地基反力模量确定方法。在此基础上,修正Reese提出的直桩p-y曲线,提出了砂土地基中斜桩p-y曲线确定方法。利用虚功原理,导出了斜桩水平承载特性分析的有限单元列式,编制相应的分析程序,通过算例验证了方法的合理性和有效性。最后,采用修正的p-y曲线法对一离心机模型试验进行了模拟分析,结果表明,计算与试验结果吻合得很好 相似文献
11.
A piled raft foundation is a combined foundation, which is developed to utilize the load-carrying capabilities of both raft and piles. To obtain an optimum piled raft design, it is important to properly evaluate and consider the load-sharing behavior between the raft and piles, which changes according to the settlement level of the piled raft. In this study, 27 three-dimensional finite element models were analyzed to investigate the piled raft coefficient with linear and nonlinear load-settlement behaviors. The length of piles was varied between 10, 15, and 20 m. The spacing between pile centers was varied between 3D, 5D, and 7D, and the pile diameter was kept constant. The number of piles and the distance between the exterior piles and the edge of the raft were maintained at 9 and 1 m, respectively. The sand conditions varied between dense, medium, and loose. The results indicated that the piled raft coefficient increases when the load-settlement curve is linear and decreases when the load-settlement curve is nonlinear. The influence of the incremental increase in pile length on the piled raft coefficient is more pronounced in short piles than in longer piles. The raft thickness has a negligible effect on the piled raft coefficient. 相似文献
12.
A simplified method of numerical analysis has been developed to estimate the deformation and load distribution of piled raft foundations subjected to vertical, lateral, and moment loads, using a hybrid model in which the flexible raft is modelled as thin plates and the piles as elastic beams and the soil is treated as springs. Both the vertical and lateral resistances of the piles as well as the raft base are incorporated into the model. Pile–soil–pile, pile–soil–raft and raft–soil–raft interactions are taken into account based on Mindlin's solutions for both vertical and lateral forces. The validity of the proposed method is verified through comparisons with several existing methods for single piles, pile groups and piled rafts. Workable design charts are given for the estimation of the lateral displacement and the load distribution of piled rafts from the stiffnesses of the raft alone and the pile group alone. Additionally, parametric studies were carried out concerning batter pile foundations. It was found that the use of batter piles can efficiently improve the deformation characteristics of pile foundations subjected to lateral loads. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
13.
《Geomechanics and Geoengineering》2013,8(4):263-282
Vertical loads effect on the lateral response of a 3×5 pile group embedded in sand is studied through a two-dimensional finite element analysis. The soil-pile interaction in three-dimensional type is idealized in the two-dimensional analysis using soil-pile interaction springs with a hysteretic nonlinear load displacement relationship. Vertical loads inducing a vertical pile head displacement of 0.1-pile diameter increase the lateral resistance of the single pile at a 60 mm lateral deflection by 8%. Vertical loads inducing the same vertical displacement applied to a pile group spaced at 3.92-pile diameter increase the overall lateral resistance by 9%. The effect on individual piles, however, depends on the pile position. The vertical load decreases the lateral resistance of the leading pile (pile 1) by 10% and increases the lateral resistances of piles 2, 3, 4, and 5 by 9%, 14%, 17%, and 35%, respectively. Vertical loads applied to the pile group increase the confining pressures in the sand deposit confined by the piles but the rate of increase in those outside the group is relatively small, resulting in the difference in a balance of lateral soil pressures acting at the back of and in front of the individual pile. 相似文献
14.
The driving response of thin‐walled open‐ended piles is studied using numerical simulation of the wave propagation inside the soil plug and the pile. An elastic finite element analysis is carried out to identify the stress wave propagation in the vicinity of the pile toe. It is found that the shear stress wave has the highest magnitude above the bottom of the soil plug. Below the bottom of the soil plug, the vertical stress wave has the highest magnitude. Although the shear stress wave propagating in the radial direction is similar in magnitude to the vertical stress wave at the bottom of the soil plug, it decays rapidly while travelling downwards. The highest vertical stress at the bottom of the soil plug appears after the vertical stress wave interacts with the shear stress wave travelling in the radial direction. Initially, the vertical stress wave propagates with the dilation wave velocity in both the radial and vertical directions. After it interacts with the shear stress wave, the vertical stress wave starts to propagate with the shear wave velocity in the radial direction and with the axial wave velocity downwards. It is concluded that at the bottom of the soil plug, the interaction between the waves travelling in radial and vertical directions is important. The capabilities of several one‐dimensional pile‐in‐pile models to reproduce the driving response given by a two‐dimensional axisymmetric finite element model is studied. It is seen that when the base of the soil plug fails, a one‐dimensional pile‐in‐pile model can be used to achieve results in agreement with the finite element model. However, when the pile is unplugged, where the base of the soil plug does not fail, a reduced finite element mesh that permits the radial wave propagation inside the soil plug must be used. Copyright © 2001 John Wiley & Sons, Ltd. 相似文献
15.
This paper presents an embedded beam formulation for discretization independent finite element (FE) analyses of interactions between pile foundations or rock anchors and the surrounding soil in geotechnical and tunneling engineering. Piles are represented by means of finite beam elements embedded within FEs for the soil represented by 3D solid elements. The proposed formulation allows consideration of piles and pile groups with arbitrary orientation independently from the FE discretization of the surrounding soil. The interface behavior between piles and the surrounding soil is represented numerically by means of a contact formulation considering skin friction as well as pile tip resistance. The pile–soil interaction along the pile skin is considered by means of a 3D frictional point‐to‐point contact formulation using the integration points of the beam elements and reference points arbitrarily located within the solid elements as control points. The ability of the proposed embedded pile model to represent groups of piles objected to combined axial and shear loading and their interactions with the surrounding soil is demonstrated by selected benchmark examples. The pile model is applied to the numerical simulation of shield driven tunnel construction in the vicinity of an existing building resting upon pile foundation to demonstrate the performance of the proposed model in complex simulation environments. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
16.
This paper evaluates the potential of two machine learning approaches i.e. Support vector machine (SVR) and Gaussian processes (GP) regression to model the oblique load capacity of batter pile groups. Linear regression was used to compare the performance of both SVR and GP based regression approaches to model the oblique load. Data set used consists of 147 samples obtained from the laboratory experiments. Out of the total sample size, 105 randomly selected samples were used for training whereas remaining 42 were used for testing the models. Input data set consist of angle of oblique load, pile length, sand relative density, number of vertical piles, number of batter piles where as oblique load was considered as output. Two kernel functions i.e. Polynomial and radial based kernel function were used with both SVR and GP regression. A comparison of results suggest that radial basis function based SVR approach works well in comparison to GP and linear regression based approaches and it could successfully be employed in modelling the oblique load capacity of batter pile groups. Parametric analysis and sensitivity analysis suggest that loading angle, pile length and number of batter pile were important in prediction of oblique load. 相似文献
17.
桩的上拔承载性能的宏观力学现象与桩周土细观结构变化相关,应用细观力学的颗粒流（PFC2D）数值模拟方法对承受上拔荷载作用的桩基进行了分析,数值模拟了上拔荷载作用的桩及桩周土的细观力学特征,研究了桩侧摩阻力的分布、桩周土剪切带的形成过程,较好的再现了桩的荷载－位移关系的实验结果,并与宏观物理实物试验的位移实测结果作了对比分析。分析了土体中剪切带形成过程中的颗粒间的细观变化及其形成过程,当上拔荷载达到极限时,上拔桩的剪切带形成原因是密砂的应变软化效应;颗粒流数值模拟的颗粒接触力与实物物理试验桩侧摩阻力是同一的,数值模拟的荷载-位移曲线与实物物理试验的荷载-位移曲线一致;桩侧摩阻力、桩上拔过程中剪切带的形成过程、桩上拔荷载-位移关系与颗粒流数值模拟的颗粒分布、速度、接触力的细观参数的变化密切相关。桩承受荷载过程中土颗粒细观结构变化的颗粒流仿真,是关于细观力学特征与宏观力学响应的初步研究。 相似文献
18.
The influence of vertical loads on the lateral response of group piles installed in sandy soil and connected together by a concrete cap is studied through finite elements analyses. The analyses focus on the five piles in the middle row of 3 × 5 pile groups. The vertical load is applied by enforcing a vertical displacement equivalent to 2% of the pile diameter through the pile cap prior to the application of the lateral loads. The results have shown that the lateral resistance of the leading pile (pile 1) does not appear to vary considerably with the vertical load. However, the vertical load leads to 23%, 36%, 64%, and 82% increase in the lateral resistance of piles 2–5, respectively. The increase in the lateral pressures in the sand deposit is the major driving factor to contribute the change in the lateral resistance of piles, depending on the position of the pile in the group. The distribution of lateral loads among piles in the group tends to be more uniform when vertical loads were considered leading to a more economical pile foundation design. 相似文献
19.
Rodrigo Salgado 《国际地质力学数值与分析法杂志》2011,35(15):1605-1635
In recent years, pile jacking has become a viable alternative installation method for displacement piles. Pile jacking produces minimal noise, vibration and air pollution during installation. In addition, it is possible, at the end of jacking, to have a good estimate of the ultimate static capacity of the pile. In this paper, the shaft resistance of piles jacked into sand is studied using one‐dimensional finite element analysis. The finite element simulations, using a two‐surface plasticity model, demonstrate the effects of relative density and confinement on the unit shaft resistance of piles jacked in sand. The impact of the number of jacking strokes on the unit shaft capacity is also assessed. Based on the numerical results, we developed equations for shaft resistance quantifying the effects of relative density, initial confinement and number of jacking strokes. Predictions using these equations are compared with data obtained from centrifuge tests and field tests. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
20.
《Geomechanics and Geoengineering》2013,8(4):291-298
The buckling behaviour of the 360 × 152 steel H-piles supporting the integral abutments of the Scotch Road Bridge, located in Trenton, New Jersey, has been studied for the cases of single pile and pile bent. Three-dimensional finite-element models for single pile and pile bent have been developed to study the behaviour of these fully embedded piles under axial and lateral loading. An iterative analysis based on extracting the eigenvalues and eigenvectors (mode shapes) that correspond to the pile(s) critical buckling loads has been adopted. The pile(s) and the surrounding sand were modelled using solid continuum elements in the finite-element model. Material non-linearity is accounted for in both the piles and the soil in the base state of the model. A parametric study has been utilized to determine the effect of the geometric and material properties of the pile and the surrounding sand on the predicted critical buckling loads of the piles. The effects of four parameters have been studied: soil stiffness, pile length, type of connection, and combining vertical and lateral loads. The results from the parametric study showed that the variation of the percentage change in the sand stiffness, pile length, and combining vertical and lateral loads with the critical buckling loads of the 360 × 152 H-piles is nonlinear. Furthermore, the parameters studied are more influential in affecting the critical buckling load of a single pile than a pile bent, with the exception of the ‘type of connection’ parameter. 相似文献