共查询到20条相似文献，搜索用时 31 毫秒
1.
In many geotechnical systems, such as reinforced slopes and embankments, soil-structure interfaces are often unsaturated. Shear behaviour of unsaturated interfaces is strongly dependent on their matric suctions, as revealed by the results of extensive laboratory tests. So far, constitutive models for unsaturated interfaces are very limited in the literature. This paper reports a new bounding surface model for saturated and unsaturated interfaces. New formulations were developed to incorporate suction effects on the flow rule and plastic modulus. To examine the capability of the proposed model, it was applied to simulate suction- and stress-controlled direct shear tests on unsaturated soil–cement, soil–steel and soil–geotextile interfaces. Measured and computed results are well matched, demonstrating that the proposed model can well capture key features of the shear behaviour of unsaturated interfaces, including suction-dependent dilatancy, stress–strain relation and peak and critical state shear strengths. 相似文献
2.
3.
以三峡库区黄土坡滑坡临江I号崩滑体的滑带土为研究对象,研究基质吸力对非饱和滑带土的强度与变形等力学性质的影响。利用GDS非饱和反压直剪仪对滑带土进行了不同净法向应力和基质吸力组合下的直剪试验。试验结果表明:相同的基质吸力作用下,滑带土抗剪强度随着净法向应力的增大而增大。当滑带土试样中基质吸力较小时(50kPa),试样剪切过程中的应力-应变曲线,随着净法向应力的增大表现为应变硬化型。之后随着基质吸力的增加,当吸力大于净法向应力时,剪切应力-应变曲线表现为较明显的达到峰值后软化。反之,应力-应变曲线表现为应变硬化型。相同净法向应力下,抗剪强度随着吸力的增大而增大,剪切应力-应变曲线由低法向应力下的达到峰值后软化向高法向应力下的应变硬化转变。剪切过程的轴向位移表现为:当吸力大于净法向应力时,表现为剪胀; 反之,表现为剪缩。滑带土固结排水剪切条件下得到的黏聚力随着基质吸力呈线性增长关系。得到了滑带土的吸力摩擦角b为13.7,有效内摩擦角有较小增长,平均有效内摩擦角15.9。 相似文献
4.
为了模拟实际工程中黄土在不排水条件下的破坏,在控制含水率不变条件下,利用非饱和土真三轴仪对不同初始吸力非饱和原状黄土进行了等向固结试验和不同中主应力参数b值的剪切试验,研究了非饱和原状黄土的力学特性。研究结果表明：真三轴等向压缩屈服应力随着初始吸力的增大而增大,吸力随着净平均应力的增大而减小,净平均应力对吸力的影响程度随着初始吸力的增大而增大。不同 值条件下,广义剪应力和净平均应力破坏状态线近似呈平行直线关系,广义剪应力和有效净平均球应力试验点可归一为饱和土的排水剪切破坏状态线;剪切破坏时吸力随着b值的增大基本呈线性增大趋势;孔隙比和净平均应力对数临界状态线近似呈线性平行关系,其斜率比饱和土大,且大于等向压缩屈服前的斜率;非饱和土孔隙比和有效净平均球应力对数临界状态线与饱和土的临界状态线近似呈线性平行关系;不同净围压条件下,不同 值非饱和土与饱和土的破坏状态孔隙比的比值与气体饱和度的试验点分布于1.0～1.2的直线带内,但同一净有效球应力条件下可以归一为一条非线性曲线。 相似文献
5.
6.
Generalization of soil–structure interface models from dry/saturated states to consider partially saturated states is studied in this paper. For this purpose, basic constitutive equations of a conventional elasto-plastic interface model are firstly presented. Then, consideration is given to the effect of partial saturation on definition of effective stress, location of the critical state line as well as the impact of interface state on plastic hardening modulus and dilatancy. For each concern, proper independent approaches together with associated constitutive equations are discussed to be included in the basic model as complementary ingredients. Among many different possibilities to combine complementary constitutive equations for effective stress, relocation of the critical state line with degree of saturation, and impact of the interface state on plastic hardening modulus and dilatancy, six essential cases are selected. Evaluations show that all six cases can realistically consider the impact of partial degree of saturation on the peak and residual shear strengths as well as the volume change behavior of unsaturated interfaces. 相似文献
7.
以高液限土为填料的加筋挡墙广泛在南方地区应用,加筋挡墙土体吸力经常随气候变化而发生变化,直接影响筋土界面强度特性,考虑吸力变化的非饱和高液限黏土-土工织物界面强度特性亟待深入研究。利用ZFY-1A型非饱和土应变控制式直剪仪对非饱和高液限黏土-土工织物界面进行控制吸力的剪切试验,探讨吸力循环变化（干湿循环）对筋-土界面剪切特性的影响。研究表明,高液限黏土-土工织物界面的抗剪强度随着净法向应力的增加而增大;随着循环次数的增加,界面强度呈现先升高而后衰减的变化规律。经历3次干湿循环的界面强度低于未经历干湿循环的强度。随着循环次数的增加,界面强度总体上呈降低趋势。吸力增加的速率 随吸力循环次数的增加先增大后减小,有效界面摩擦角 、界面有效黏聚力 、界面综合摩擦系数 、综合摩擦系数比K与此类似。 含水率变化量的最大值随着净法向应力、循环次数的增加而增大。最大剪胀量 随循环次数的增加先增大后减小,随净法向应力的增大而减小。最后通过对数拟合,得出经历若干次基质吸力循环后的界面强度计算公式。 相似文献
8.
A constitutive model for simulation of the behavior of unsaturated interfaces is presented here. The model is an extension of an existing critical state compatible interface model for dry and saturated interfaces that was already proposed by one of the authors [Lashkari, A. 2013. Int. J. Numer. Anal. Meth. Geomech. 37 (8): 904–931]. For a proper simulation of the behavior of partially saturated interfaces, the extended model is formulated in terms of two pairs of work conjugate stress–strain‐like variables. The modified model simulations are compared with the existing data of dry, unsaturated, and saturated interfaces. For each interface type, it is shown that the proposed model can capture the essential elements of the behavior using a unique set of parameters. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
9.
非饱和土应力变量选取原则刍议 总被引：2，自引：0，他引：2
在非饱和土本构模型研究中,所选取的变量是否是非饱和土合适的应力变量往往被研究人员所忽视,这会阻碍本构模型的进一步发展。从土体的微观结构、能量守衡及力学平衡这3方面对非饱和土应力变量进行研究,以此提出了非饱和土应力变量选取应遵循的3个原则,强调指出非饱和土应力变量与应力状态变量的区别,并对本构模型研究中常用的应力变量进行分析,发现基质吸力、净法向应力并非为非饱和土应力变量,而有效应力和吸应力为其应力变量。建议使用有效应力来建立本构关系,其除了能满足文中提出的选取原则外,还能与饱和土理论之间有很好的过渡。文中的非饱和土应力变量选取原则还不成熟,但其重要性不容忽视,该研究还有待进一步补充和完善。 相似文献
10.
An elasto-plastic model is proposed for modeling the constitutive behavior of the interface between gravelly soils and structural materials. This model is based on the two-surface plasticity formulation and it is compatible with the concept of critical state soil mechanics. The model requires the same set of eight calibration parameters for predicting the monotonic and cyclic responses of both loose and dense interfaces. The model simulates cyclic densification, shear degradation and the effects of normal pressure, soil density, and stress path. The performance of the proposed constitutive model is validated by tests data under different normal stresses and boundary conditions. 相似文献
11.
非饱和土的本构模型研究 总被引：1，自引：0，他引：1
引用平均土骨架应力的概念,研究推导出非饱和土的刚度参数随吸力变化而变化的关系式,进而推导得到用平均土骨架应力表述的非饱和土LC屈服面函数以及硬化规律。从土力学原理推导,得到土样由于在净应力和吸力作用下产生体积变形引起土样饱和度变化的关系式。由平均土骨架应力推广,得到三轴应力状态的椭圆屈服函数,这一非饱和土本构模型的优点在于考虑了应力作用后土样饱和度的变化,通过对已有试验数据的初步验证,表明提出的非饱和土本构模型的合理性和适用性。 相似文献
12.
应力路径对土的强度和变形性质具有重要影响。相对于饱和土而言,控制吸力条件下的非饱和土三轴压缩状态的应力路径研究更加复杂。随着非饱和土本构理论的不断发展,理论和试验研究结果表明,非饱和土弹塑性本构模型可以用来近似地描述非饱和土的强度和变形性质。因而,运用非饱和土弹塑性本构模型对控制吸力条件下的3种非饱和土三轴压缩应力路径试验进行数值模拟是一种有效的理论研究手段。采用Barcelona模型能够对此类试验进行较好的数值模拟,其研究结果表明,在控制吸力条件的三轴压缩状态下应力路径对非饱和土的强度和变形性质具有重要影响。 相似文献
13.
A three-dimensional (3D) soil–structure interface model is proposed within the two-mechanism constitutive theory and bounding surface theory originally established for soils. The proposed model has two main characteristics: first, the model is formulated based on two different and superposed deformation mechanisms. The first mechanism is due to the stress ratio increment, and the second is due to the normal stress increment. Each mechanism induces a shear strain component and a normal strain component. The proposed model can be reduced to the conventional single-mechanism interface model. Second, the plastic modulus and stress dilatancy are defined using the bounding surface theory. The plastic flow rule under cyclic loading is modified and assumed to be dependent on both the stress state of the mapping point and the stress reversal loading direction. The proposed model was validated against the available 3D interface tests and was found to satisfactorily reflect the salient features of the interfaces under monotonic and cyclic loading paths with different normal boundaries. The problem in which the elastic normal stiffness in conventional single-mechanism interface models is often underestimated to enhance the simulation performance under varying normal stress conditions is solved by incorporating the second mechanism. And the effect of the second mechanism on the modeling behavior is discussed. The modified plastic flow direction accurately simulates the 3D cyclic shear response, and the difference between the model simulation and test result increases with the number of cycles by use of the plastic flow direction defined in conventional bounding surface theory. 相似文献
14.
吸力历史对非饱和土力学性质的影响 总被引：1，自引：0，他引：1
现在被广泛公认的由Fredlund提出的非饱和土力学的双参数理论,即净应力和吸力为非饱和土的应力状态变量,不能直接考虑吸力历史及其饱和度对非饱和土的应力-应变关系和强度的影响。非饱和土三轴试验结果表明,即使净应力和吸力相同的条件下,经过干-湿循环试样与未经过干-湿循环试样的应力比-应变关系和强度是不相同的。在其他条件相同时,经历过干-湿循环的试样比未经过干-湿循环试样的应力比-应变关系要高、强度大和体变小。经过干-湿循环试样的饱和度低而强度高,主要是由于经过先期较高的吸力,相当于受过较大的前期有效压力,使试样成为超固结土。更多不同吸力历史的对比试验有待于进一步研究,以便为非饱和土的水力-力学特性耦合弹塑性本构模型定量地表示上述非饱和土的性质提供基础性试验数据。 相似文献
15.
基于广义位势理论建立的岩土体材料本构模型以及岩土体材料与结构接触面本构模型原理相通,只是前者是在三轴剪切试验条件下的三维应力空间建模,后者是在单剪试验条件下的二维应力空间建模。单剪试验条件下土与结构的接触面问题可以看作是法向与切向应力空间上的二维问题,其试验结果可以表达成由应力、应变组成的二维矢量。结合接触面力学特性,确定应力空间中的势函数以及塑性状态方程,可以推导出双重势面接触面弹塑性本构方程的一般表达式。进一步取两个势函数分别为法向应力和切向应力,建立简化双重势面接触面弹塑性模型的本构方程,该方程可直接应用于有限元等数值分析。结合试验实例对建模方法的合理性进行验证,模型拟合效果良好。研究结果表明,基于广义塑性位势理论建立接触面本构模型无需推求塑性势函数和屈服函数,可以直接得到弹塑性刚度矩阵,且建模方便。 相似文献
16.
考虑体变对非饱和土土-水状态的影响,将状态曲面函数引入传统的Vanapalli强度公式得到与孔隙比相关的抗剪强度准则,新准则使用饱和土的强度参数和两条不同孔隙比对应的土-水特征曲线。选择一种尾矿砂和高岭土的混合土料为研究对象,进行一系列的土-水特征曲线试验、吸力控制的等向压缩和三轴剪切试验。试验结果表明,新准则能更准确地预测非饱和土的强度,证明了传统强度预测的误差主要来源于忽略了体变导致的土-水状态变化,并提出在不同应力空间内精确地获得抗剪强度包线的方法,合理地解释了强度包线斜率在净应力-强度平面内随吸力增大、强度包线形状在吸力-强度平面内随净应力发生变化的特性。 相似文献
17.
吸力对弱膨胀土强度贡献的试验研究与预测分析 总被引：1，自引：1，他引：0
对部分应用土-水特征曲线来预测非饱和土抗剪强度的公式进行了归纳分析。应用压力板仪与非饱和三轴仪,测试了荆门原状弱膨胀土的土-水特征曲线和控制吸力的非饱和三轴抗剪强度参数,并将试验结果与各抗剪强度公式的预测值进行对比,分析了各强度公式的局限性。试验结果表明,非饱和原状膨胀土的净法向应力摩擦角随着吸力的不同而变化,根据双应力变量理论确定的吸力对强度的贡献与围压有关,不同围压下吸力对强度的贡献不同,表观凝聚力 与吸力间符合乘幂函数关系。 相似文献
18.
法向应力对土与结构接触面循环单剪力学特性的影响研究具有重要意义。运用80 t大型三维接触面试验机,进行了不同法向应力下粗粒土与结构接触面单剪试验,分析了法向应力对接触面循环单剪力学特性的影响规律。试验结果表明,法向应力对接触面变形位移、滑动位移、切向应力、可逆性剪切体变和不可逆性剪切体变以及抗剪强度等接触面性能参量的数值有显著影响,但对参量间关系形式影响较小。法向应力越大,接触面变形位移在初始几个循环内越大,随循环剪切的进行,其减小速率越快,最终稳定值越小;切向刚度越大,切向应力稳定值也越大,初始几个循环内切向刚度系数越小;不可逆性剪切体变越大,可逆性剪切体变峰值和稳定值越小,相变位移和相变应力比越小;抗剪强度越大,其异向程度则先增大后减小。不同法向应力下,接触面循环抗剪强度与法向应力符合摩尔-库仑准则;切向应力比-切向位移关系、不可逆性剪切体变和剪切功密度关系均具有良好一致性,基本不受法向应力影响,可用双曲线模型描述,这将大大简化接触面本构描述。 相似文献
19.
A simple semi-hyperbolic state-dependent constitutive model for sand-structure interfaces is proposed. The model formulation is consistent with critical state soil mechanics since void ratio evolves continuously with shear strain from initial state towards asymptotic critical state at extremely large shear strains. The model takes into account influence of normal stiffness on volume change and stress path. The proposed interface model is implemented in a pile segment analysis scheme for simulation of shaft resistance mobilization in non-displacement piles. Results reveal that the proposed pile segment analysis can well predict shaft resistance of model piles embedded in different sands. 相似文献
20.
A hierarchical thermo‐hydro‐plastic constitutive model for unsaturated soils and its numerical implementation 
下载免费PDF全文
下载免费PDF全文 《国际地质力学数值与分析法杂志》2018,42(15):1785-1805
Unsaturated soils are highly heterogeneous 3‐phase porous media. Variations of temperature, the degree of saturation, and density have dramatic impacts on the hydro‐mechanical behavior of unsaturated soils. To model all these features, we present a thermo‐hydro‐plastic model in which the hydro‐mechanical hardening and thermal softening are incorporated in a hierarchical fashion for unsaturated soils. This novel constitutive model can capture heterogeneities in density, suction, the degree of saturation, and temperature. Specifically, this constitutive model has 2 ingredients: (1) it has a “mesoscale” mechanical state variable—porosity and 3 environmental state variables—suction, the degree of saturation, and temperature; (2) both temperature and mechanical effects on water retention properties are taken into account. The return mapping algorithm is applied to implement this model at Gauss point assuming an infinitesimal strain. At each time step, the return mapping is conducted only in principal elastic strain space, assuming no return mapping in suction and temperature. The numerical results obtained by this constitutive model are compared with the experimental results. It shows that the proposed model can simulate the thermo‐hydro‐mechanical behavior of unsaturated soils with satisfaction. We also conduct shear band analysis of an unsaturated soil specimen under plane strain condition to demonstrate the impact of temperature variation on shear banding triggered by initial material heterogeneities. 相似文献