共查询到20条相似文献，搜索用时 132 毫秒
1.
Residual displacements of single‐degree‐of‐freedom systems due to ground motions with velocity pulses or fling step displacements are presented as a function of period T and of its ratio to the pulse period Tp. Four hysteretic behaviors are considered: bilinear elastoplastic, stiffness‐degrading with cycling, stiffness‐cum‐strength degrading, with or without pinching. When expressed in terms of T/Tp, peak inelastic and residual displacements due to motions with a pulse or fling appear similar to those due to far‐fault motions, if the response to far‐field records are expressed in terms of the ratio of T to the record's characteristic period. However, as the latter is usually much shorter than the pulse period of motions with fling, the range of periods of interest for common structures becomes a short‐period range under fling motions and exhibits very large amplification of residual and peak inelastic displacements. Similar, but less acute, are the effects of motions with a velocity pulse. Wavelets of different complexity are studied as approximations to near‐fault records. Simple two‐parameter wavelets for fling motions overestimate peak inelastic displacements; those for pulse‐type motions overestimate residual displacements. A more complex four‐parameter wavelet for motions with a velocity pulse predicts overall well residual and peak displacements due to either pulse‐ or fling‐type motions; a hard‐to‐identify parameter of the wavelet impacts little computed residual displacements; another significantly affects them and should be carefully estimated from the record. Even this most successful of wavelets overpredicts residual displacements for the periods of engineering interest. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
2.
This paper summarizes the results of a comprehensive statistical study aimed at evaluating peak lateral inelastic displacement demands of structures with known lateral strength and stiffness built on soft soil site conditions. For that purpose, empirical information on inelastic displacement ratios which are defined as the ratio of peak lateral inelastic displacement demands to peak elastic displacement demands are investigated. Inelastic displacement ratios were computed from the response of single‐degree‐of‐freedom systems having 6 levels of relative lateral strength when subjected to 118 earthquake ground motions recorded on bay‐mud sites of the San Francisco Bay Area and on soft soil sites located in the former lake‐bed zone of Mexico City. Mean inelastic displacement ratios and their corresponding scatter are presented for both ground motion ensembles. The influence of period of vibration normalized by the predominant period of the ground motion, the level of lateral strength, earthquake magnitude, and distance to the source are evaluated and discussed. In addition, the effects of post‐yield stiffness and of stiffness and strength degradation on inelastic displacement ratios are also investigated. It is concluded that magnitude and distance to the source have negligible effects on constant‐strength inelastic displacement ratios. Results also indicate that weak and stiffness‐degrading structures in the short spectral region could experience inelastic displacement demands larger than those corresponding to non‐degrading structures. Finally, a simplified equation obtained using regression analyses aimed at estimating mean inelastic displacement ratios is proposed for assisting structural engineers in performance‐based assessment of structures built on soft soil sites. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
3.
In two companion papers a simplified non‐linear analysis procedure for infilled reinforced concrete frames is introduced. In this paper a simple relation between strength reduction factor, ductility and period (R–µ–T relation) is presented. It is intended to be used for the determination of inelastic displacement ratios and of inelastic spectra in conjunction with idealized elastic spectra. The R–µ–T relation was developed from results of an extensive parametric study employing a SDOF mathematical model composed of structural elements representing the frame and infill. The structural parameters, used in the proposed R–µ–T relation, in addition to the parameters used in a usual (e.g. elasto‐plastic) system, are ductility at the beginning of strength degradation, and the reduction of strength after the failure of the infills. Formulae depend also on the corner periods of the elastic spectrum. The proposed equations were validated by comparing results in terms of the reduction factors, inelastic displacement ratios, and inelastic spectra in the acceleration–displacement format, with those obtained by non‐linear dynamic analyses for three sets of recorded and semi‐artificial ground motions. A new approach was used for generating semi‐artificial ground motions compatible with the target spectrum. This approach preserves the basic characteristics of individual ground motions, whereas the mean spectrum of the whole ground motion set fits the target spectrum excellently. In the parametric study, the R–µ–T relation was determined by assuming a constant reduction factor, while the corresponding ductility was calculated for different ground motions. The mean values proved to be noticeably different from the mean values determined based on a constant ductility approach, while the median values determined by the different procedures were between the two means. The approach employed in the study yields a R–µ–T relation which is conservative both for design and performance assessment (compared with a relation based on median values). Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
4.
Evaluation of seismic displacement demands from the September 19, 2017 Puebla‐Morelos (Mw = 7.1) earthquake in Mexico City 
下载免费PDF全文
下载免费PDF全文 This short communication presents the assessment of seismic inelastic and elastic displacement demands computed from earthquake ground motions (EQGMs) recorded in Mexico City during the intermediate‐depth intraslab Puebla‐Morelos earthquake on 19 September 2017 (Mw = 7.1). Evaluation is conducted by means of peak elastic and inelastic displacement demand spectra, inelastic displacement ratio, CR, spectra, and generalized interstory drift spectra computed for selected recording stations located in different soil sites of Mexico City, including those located in areas of reported collapsed buildings. Results of this study confirm previous observations made from interplate (subduction) EQGMs that peak inelastic displacement demands are greater than corresponding elastic counterparts for short‐to‐medium period structures, while the opposite is true for medium‐to‐long period structures. Possible basin site effects were identified from generalized interstory drift spectra. It is also shown that an equation introduced in the literature to obtain estimates of CR developed from interplate EQGMs provides also a good estimate for mean CR computed from the intermediate‐depth intraslab EQGMs. 相似文献
5.
The seismic performance of existing structures can be assessed based on nonlinear static procedures, such as the Capacity Spectrum Method. This method essentially approximates peak responses of an inelastic single‐degree‐of‐freedom (SDOF) system using peak responses of an equivalent linear SDOF model. In this study, the equivalent linear models of inelastic SDOF systems are developed based on the constant strength approach, which does not require iteration for assessing the seismic performance of existing structures. To investigate the effects of earthquake type and seismic region on the equivalent linear models, four ground‐motion data sets—Japanese crustal/interface/inslab records and California crustal records—are compiled and used for nonlinear dynamic analysis. The analysis results indicate that: (1) the optimal equivalent linear model parameters (i.e. equivalent vibration period ratio and damping ratio) decrease with the natural vibration period, whereas they increase with the strength reduction factor; (2) the impacts of earthquake type and seismic region on the equivalent linear model parameters are not significant except for short vibration periods; and (3) the degradation and pinching effects affect the equivalent linear model parameters. We develop prediction equations for the optimal equivalent linear model parameters based on nonlinear least‐squares fitting, which improve and extend the current nonlinear static procedure for existing structures with degradation and pinching behavior. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
6.
Results of an analytical study aimed at evaluating residual displacement ratios, Cr, which allow the estimation of residual displacement demands from maximum elastic displacement demands is presented. Residual displacement ratios were computed using response time‐history analyses of single‐degree‐of‐freedom systems having 6 levels of relative lateral strength when subjected to an ensemble of 240 earthquake ground motions recorded in stations placed on firm sites. The results were statistically organized to evaluate the influence of the following parameters: period of vibration, level of relative lateral strength, site conditions, earthquake magnitude, and distance to the source. In addition, the influence of post‐yield stiffness ratio in bilinear systems and of the unloading stiffness in stiffness‐degrading systems was also investigated. A special emphasis is given to the uncertainty of these ratios. From this study, it is concluded that mean residual displacement ratios are more sensitive to changes in local site conditions, earthquake magnitude, distance to the source range and hysteretic behaviour than mean inelastic displacement ratios. In particular, residual displacement ratios exhibit large levels of record‐to‐record variability and, therefore, this dispersion should be taken into account when estimating residual displacements. A simplified expression is presented to estimate mean residual displacements ratios for elastoplastic systems during the evaluation of existing structures built on firm soil sites. Copyright © 2005 John Wiley & Sons, Ltd. 相似文献
7.
This study develops a straightforward approximate method to estimate inelastic displacement ratio, C1 for base‐isolated structures subjected to near‐fault and far‐fault ground motions. Taking into account the inelastic behavior of isolator and superstructure, a 2 degrees of freedom model is employed. A total of 90 earthquake ground motions are selected and classified into different clusters according to the frequency content features of records represented by the peak ground acceleration to peak ground velocity ratio, Ap/Vp. A parametric study is conducted, and effective factors in C1 (i.e., fundamental vibration period of the superstructure, Ts; postyield stiffness ratio of the superstructure, αs; strength reduction ratio, R; vibration period of the isolator, Tb; strength of the isolator, Q; ratio of superstructure mass to total mass of the system, γm) are recognized. The results indicate that the practical range of C1 values could be expected for base‐isolated structures. Subsequently, effective parameters are included in simple predictive equations. Finally, the accuracy of the proposed approximate equations is evaluated and verified through error measurement, and comparisons are made in the analyses. 相似文献
8.
It is widely accepted that ductility design improves the seismic capacity of structures worldwide. Nevertheless, inelastic deformation allows serious damage to occur in structures. Previous studies have shown that a certain level of postyield stiffness may reduce both the peak displacement and residual deformation of a structure. In recent years, several high-strength elastic materials, such as fiber-reinforced polymer (FRP) and high-strength steel bars, have been developed. Application of these materials can easily provide a structure with a much higher and more stable postyield stiffness. Many materials, members, and structures that incorporate both high-strength elastic materials and conventional materials show significant postyield hardening (PYH) behaviors. The significant postyield stiffness of PYH structures can help effectively reduce both peak and residual deformations, providing a choice when designing resilient structures. However, the findings of previous studies of structures with elastic-perfectly plastic (EPP) behavior or small postyield stiffness may not be accurate for PYH structures. The postyield stiffness of a structure must be considered an important primary structural parameter, in addition to initial stiffness, yielding strength, and ductility. In this paper, extensive time history and statistical analyses are carried out for PYH single–degree-of-freedom (SDOF) systems. The mean values and coefficients of variation of the peak displacement and residual deformation are obtained and discussed. A new R-μp-T-α relationship and damage index for PYH structures are proposed. A theoretical model for the calculation of residual deformation is also established. These models provide a basis for developing the appropriate seismic design and performance evaluation procedures for PYH structures. 相似文献
9.
Residual displacements are sensitive to ground motion details, hence more random than peak inelastic displacements. Among the factors with systematic impact on residual displacements, the post‐yield‐stiffness‐ratio has been studied thoroughly; its effects are not investigated further. Concerning another important factor, the hysteresis law, past studies have focused on the bilinear model, which does not represent concrete structures. Residual displacements from nonlinear response‐history analyses of bilinear systems are compared to those from models tuned to concrete structures, conforming to modern codes, deficient or intermediate. Deficient‐type structures, with their narrow, almost self‐centering hysteresis loops, develop markedly smaller residual displacements than those with stable energy‐dissipating behavior. A velocity pulse in the motion increases peak inelastic and residual displacements by about the same proportion. As a fraction of the peak inelastic or spectral displacement, residual displacements are on average almost independent of the period and increase when the lateral strength ratio increases, reaching a limit at a lateral strength ratio of 2 to 5. Peak inelastic displacements are a better basis for estimation of residual displacements than spectral ones: the ratio of the two is almost independent of the period, the lateral strength ratio (beyond values of 2 to 3) and velocity pulses. The spectrum of the ratio of residual displacement to peak inelastic or spectral displacement is considered as a random process of period; its mean and variance functions, marginal probability distributions and autocorrelation functions are given in terms of the lateral strength ratio, the hysteresis model and the presence of a velocity pulse. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
10.
Results of a detailed statistical study of constant relative strength inelastic displacement ratios to estimate maximum lateral inelastic displacement demands on existing structures from maximum lateral elastic displacement demands are presented. These ratios were computed for single‐degree‐of‐freedom systems with different levels of lateral strength normalized to the strength required to remain elastic when subjected to a relatively large ensemble of recorded earthquake ground motions. Three groups of soil conditions with shear wave velocities higher than 180m/s are considered. The influence of period of vibration, level of lateral yielding strength, site conditions, earthquake magnitude, distance to the source, and strain‐hardening ratio are evaluated and discussed. Mean inelastic displacement ratios and those associated with various percentiles are presented. A special emphasis is given to the dispersion of these ratios. It is concluded that distance to the source has a negligible influence on constant relative strength inelastic displacement ratios. However, for periods smaller than 1s earthquake magnitude and soil conditions have a moderate influence on these ratios. Strain hardening decreases maximum inelastic displacement at a fairly constant rate depending on the level of relative strength for periods of vibration longer than about 1.0s while it decreases maximum inelastic displacement non‐linearly as the period of vibration shortens and as the relative‐strength ratio increases for periods of vibration shorter than 1.0s. Finally, results from non‐linear regression analyses are presented that provide a simplified expression to be used to approximate mean inelastic displacement ratios during the evaluation of existing structures built on firm sites. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
11.
SPO2IDA is introduced, a software tool that is capable of recreating the seismic behaviour of oscillators with complex quadrilinear backbones. It provides a direct connection between the static pushover (SPO) curve and the results of incremental dynamic analysis (IDA), a computer‐intensive procedure that offers thorough demand and capacity prediction capability by using a series of nonlinear dynamic analyses under a suitably scaled suite of ground motion records. To achieve this, the seismic behaviour of numerous single‐degree‐of‐freedom (SDOF) systems is investigated through IDA. The oscillators have a wide range of periods and feature pinching hysteresis with backbones ranging from simple bilinear to complex quadrilinear with an elastic, a hardening and a negative‐stiffness segment plus a final residual plateau that terminates with a drop to zero strength. An efficient method is introduced to treat the backbone shape by summarizing the analysis results into the 16, 50 and 84% fractile IDA curves, reducing them to a few shape parameters and finding simpler backbones that reproduce the IDA curves of complex ones. Thus, vast economies are realized while important intuition is gained on the role of the backbone shape to the seismic performance. The final product is SPO2IDA, an accurate, spreadsheet‐level tool for performance‐based earthquake engineering that can rapidly estimate demands and limit‐state capacities, strength reduction R‐factors and inelastic displacement ratios for any SDOF system with such a quadrilinear SPO curve. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
12.
13.
In order to investigate the response of structures to near‐fault seismic excitations, the ground motion input should be properly characterized and parameterized in terms of simple, yet accurate and reliable, mathematical models whose input parameters have a clear physical interpretation and scale, to the extent possible, with earthquake magnitude. Such a mathematical model for the representation of the coherent (long‐period) ground motion components has been proposed by the authors in a previous study and is being exploited in this article for the investigation of the elastic and inelastic response of the single‐degree‐of‐freedom (SDOF) system to near‐fault seismic excitations. A parametric analysis of the dynamic response of the SDOF system as a function of the input parameters of the mathematical model is performed to gain insight regarding the near‐fault ground motion characteristics that significantly affect the elastic and inelastic structural performance. A parameter of the mathematical representation of near‐fault motions, referred to as ‘pulse duration’ (TP), emerges as a key parameter of the problem under investigation. Specifically, TP is employed to normalize the elastic and inelastic response spectra of actual near‐fault strong ground motion records. Such normalization makes feasible the specification of design spectra and reduction factors appropriate for near‐fault ground motions. The ‘pulse duration’ (TP) is related to an important parameter of the rupture process referred to as ‘rise time’ (τ) which is controlled by the dimension of the sub‐events that compose the mainshock. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
14.
A probabilistic approach to estimate maximum inelastic displacement demands of single‐degree‐of‐freedom (SDOF) systems is presented. By making use of the probability of exceedance of maximum inelastic displacement demands for given maximum elastic spectral displacement and the mean annual frequency of exceedance of elastic spectral ordinates, a simplified procedure is proposed to estimate mean annual frequencies of exceedance of maximum inelastic displacement demands. Simplifying assumptions are thoroughly examined and discussed. Using readily available elastic seismic hazard curves the procedure can be used to compute maximum inelastic displacement seismic hazard curves and uniform hazard spectra of maximum inelastic displacement demands. The resulting maximum inelastic displacement demand spectra provide a more rational way of establishing seismic demands for new and existing structures when performance‐based approaches are used. The proposed procedure is illustrated for elastoplastic SDOF systems having known‐lateral strength located in a region of high seismicity in California. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
15.
Giovanni De Francesco 《地震工程与结构动力学》2019,48(2):188-209
This paper focuses on constant-ductility inelastic displacement ratios of self-centering single-degree-of-freedom (SDF) systems with two different levels of energy dissipation capacity, in the presence of 5% viscous damping ratio. A statistical analysis is developed considering an earthquake database composed of 228 ground motions recorded in California with magnitudes greater than six and organized for NEHRP soil class, ground motion duration, and peak ground acceleration. The response of self-centering SDF systems with large variability of initial periods, ductility levels, and postyield stiffness ratios is investigated and compared with the responses of SDF systems with bilinear plastic, Clough, and Takeda hysteresis. The inelastic demand variation with soil class, initial period, postyield stiffness ratio, unloading stiffness degradation, ductility level, and hysteretic behavior is highlighted. Simple and conservative analytical estimates of constant-ductility inelastic displacement ratios for mean and 90th percentile values in terms of initial period, ductility level, and postyield stiffness ratio are proposed to allow the extension of the Displacement-Based Design via Inelastic Displacement Ratio (CμDBD) to self-centering structural systems. 相似文献
16.
The conventional approach of obtaining the inelastic response spectra for the aseismic design of structures involves the reduction of elastic spectra via response modification factors. A response modification factor is usually taken as a product of (i) strength factor, RS, (ii) ductility factor, Rμ, and (iii) redundancy factor, RR. Ductility factor, also known as strength reduction factor (SRF), is considered to primarily depend on the initial time period of the single‐degree‐of‐freedom (SDOF) oscillator and the displacement ductility demand ratio for the ground motion. This study proposes a preliminary scaling model for estimating the SRFs of horizontal ground motions in terms of earthquake magnitude, strong motion duration and predominant period of the ground motion, geological site conditions, and ductility demand ratio, with a given level of confidence. The earlier models have not considered the simultaneous dependence of the SRFs on various governing parameters. Since the ductility demand ratio is not a complete measure of the cumulative damage in the structure during the earthquake‐induced vibrations, the existing definition of the SRF is sought to be modified with the introduction of damage‐based SRF (in place of ductility‐based SRF). A parallel scaling model has been proposed for estimating the damage‐based SRFs. This model considers damage and ductility supply ratio as parameters instead of ductility demand ratio. Through a parametric study on ductility‐based SRFs, it has been shown that the hitherto assumed insensitivity of earthquake magnitude and strong motion duration may not be always justified and that the initial time period of the oscillator plays an important role in the dependence of SRF on these parameters. Further, the damage‐based SRFs are found to show similar parametric dependence as observed in the case of the ductility‐based SRFs. Copyright © 2000 John Wiley & Sons, Ltd. 相似文献
17.
Period lengthening, exhibited by structures when subjected to strong ground motions, constitutes an implicit proxy of structural inelasticity and associated damage. However, the reliable prediction of the inelastic period is tedious and a multi‐parametric task, which is related to both epistemic and aleatory uncertainty. Along these lines, the objective of this paper is to investigate and quantify the elongated fundamental period of reinforced concrete structures using inelastic response spectra defined on the basis of the period shift ratio (Tin/Tel). Nonlinear oscillators of varying yield strength (expressed by the force reduction factor, Ry), post‐yield stiffness (ay) and hysteretic laws are examined for a large number of strong motions. Constant‐strength, inelastic spectra in terms of Tin/Tel are calculated to assess the extent of period elongation for various levels of structural inelasticity. Moreover, the influence that structural characteristics (Ry, ay and degrading level) and strong‐motion parameters (epicentral distance, frequency content and duration) exert on period lengthening are studied. Determined by regression analyses of the data obtained, simplified equations are proposed for period lengthening as a function of Ry and Tel. These equations may be used in the framework of the earthquake record selection and scaling. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
18.
Capacity-based inelastic displacement spectra that comprise an inelastic displacement ratio (CR ) spectrum and the corresponding damage index (DI ) spectrum are proposed in this study to aid seismic design and evaluation of reinforced concrete (RC) bridges. Nonlinear time history analyses of single-degree-of-freedom (SDOF) systems are conducted using a versatile smooth hysteretic model when subjected to far-field and near-fault ground motions. It is demonstrated that the Park and Ang damage index can be a good indicator for assessing the actual visible damage condition of columns regardless of its loading history, providing a better insight into the seismic performance of bridges. The computed spectra for near-fault (NF) ground motions show that as the magnitude of pulse period ranges increases from NF1 (0.5-2.5 seconds) to NF2 (2.5-5.5 seconds), the spectral ordinates of the CR and DI spectra increase moderately. In contrast, the computed spectra do not show much difference between NF2 and NF3 (5.5-10.5 seconds) when the period of vibration Tn≤ 1.5 seconds, after which the spectral ordinates of NF3 tend to increase obviously, whereas those of NF2 decrease with increasing Tn . Moreover, when relative strength ratio R = 5.0, nearly all of the practical design scenarios could not survive NF3. On the basis of the computed spectra, CR and DI formulae are presented as a function of Tn , R , and various design parameters for far-field and near-fault ground motions. Finally, an application of the proposed spectra to the performance-based seismic design of RC bridges is presented using DI as the performance objective. 相似文献
19.
This paper presents a statistical study of the kinematic soil-foundation-structure interaction effects on the maximum inelastic
deformation demands of structures. Discussed here is the inelastic displacement ratio defined as the maximum inelastic displacement
demands of structures subjected to foundation input motions divide by those of structures subjected to free-field ground motions.
The displacement ratio is computed for a wide period range of elasto-plastic single-degree-of-freedom (SDOF) systems with
various levels of lateral strength ratios and with different sizes of foundations. Seventy-two earthquake ground motions recorded
on firm soil with average shear wave velocities between 180 m/s and 360 m/s are adopted. The effects of period of vibration,
level of lateral yielding strength and dimension of foundations are investigated. The results show that kinematic interaction
will reduce the maximum inelastic displacement demands of structures, especially for systems with short periods of vibration,
and the larger the foundation size the smaller the maximum inelastic displacement becomes. In addition, the inelastic displacement
ratio is nearly not affected by the strength ratio of structures for systems with periods of vibration greater than about
0.3 s and with strength ratios smaller than about 3.0. Expressions obtained from nonlinear regression analyses are also proposed
for estimating the effects of kinematic soil-foundation-structure interaction from the maximum deformation demand of the inelastic
system subjected to free-field ground motions. 相似文献
20.
Quantification of ground-motion parameters and response spectra in the near-fault region 总被引：2，自引：1，他引：1
R. Rupakhety S. U. Sigurdsson A. S. Papageorgiou R. Sigbj?rnsson 《Bulletin of Earthquake Engineering》2011,9(4):893-930
This study focuses on the characteristics of near-fault ground motions in the forward-direction and structural response associated
with them. These ground motions are narrow-banded in nature and are characterized by a predominant period at which structures
excited by them are severely affected. In this work, predominant period is defined as the undamped natural period of a single-degree-of-freedom
(SDOF) oscillator at which its 5% damped linear elastic pseudo-spectral velocity (PSV) contains a clear and dominant peak. It is found that a linear relationship exists between predominant period and seismic
moment. An empirical equation describing this relationship is presented by using a large set of accelerograms. Attenuation
equations are developed to estimate peak ground velocity (PGV) as a function of earthquake magnitude and source-to-site distance. In addition, a predictive equation for spectral shapes
of PSV (i.e., PSV normalized by PGV) is presented as a continuous function of the undamped natural period of SDOF oscillators. The model is independent of PGV, and can be used in conjunction with any available PGV attenuation relation applicable to near-fault ground motion exhibiting forward-directivity effects. Furthermore, viscous
damping of the SDOF is included in the model as a continuous parameter, eliminating the use of so-called damping correction
factors. Finally, simple equations relating force reduction factors and displacement ductility of elasto-plastic SDOF systems
are presented. 相似文献