首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 62 毫秒
1.
Dried, mature leaves of Aegle Marmelos tree were converted to a powder, which was used as a biosorbent for dyes in water with methylene blue as a case study. The biosorbent had a surface area of 52.63 mg/g, and FTIR spectra showed the presence of –COOH, –NH2, –R–SC=O (thioester) and R1–S(=O, =O)-N(–R2, –R3) groups on the surface. The particles were found to be porous in nature from scanning electron micrographs, and EDX measurements showed the elements C, O, Na, Mg, K, Ca and Fe on the surface. Batch adsorption experiments showed that the adsorption of the dye was preferred at near-neutral conditions. Adsorption equilibrium was achieved in ~120 min with maximum dye uptake of 19.9 mg/g. Investigation into the kinetics of adsorption indicated that second-order kinetics gave the best fit to the experimental data, and a rate coefficient of 8.0 × 10?2 to 32.3 × 10?2 g mg?1 min?1 was obtained.  相似文献   

2.
In the present research, coal fly ash, a waste by-product of thermal power plant, has been segregated to obtain hollow and spherical cenospheres which combined with activated carbon in different ratio for effectual remediation of wastewater. Fabricated cenospheres activated carbon (CNAC) composites were characterized by ATR-FTIR, SEM, XRD, BET and CILAS for functionality, surface modification, crystallinity, surface area, pore volume, pore size and particle size analysis, respectively. Batch adsorption has been applied to appraised maximum removal of Disperse Orange 25 (DO) and Disperse Blue 79:1 (DB) dyes at varying solution pH 2 to 12, adsorbent dose 0.1 g cenospheres + 0.1 g AC to 1.0 g cenospheres + 1.0 g AC, dye concentration 10 to 100 mg/L, agitation speed 80 to 240 rpm and contact time 5 to 300 min at three different temperatures (25, 35 and 45 °C). The maximum percentage removal was found to be 79 and 76% for DO and DB dyes, respectively, at optimized condition. Langmuir isotherm showed good interaction with adsorption data, and the obtained maximum equilibrium adsorption capacity was found to be 90.91 mg/g for DO and 83.33 mg/g for DB at 45 °C. Eventually, the negative ?G° (? 7.513 for DO and ? 7.767 for DB) has suggested the feasibility of dyes adsorption on CNAC composites.  相似文献   

3.
Biofilms wasted from biotrickling filters was dried and used as biosorbent for Cd(II) removal from aqueous solutions. The adsorption condition and effect, adsorption isotherms and kinetics of Cd(II) removal were investigated, and the effects of competitive metal ions on Cd(II) removal were also examined. Results showed that the dry waste biofilms reached the maximum adsorption capacity of 42 mg/g of Cd(II) at 25 °C for 120 min when the initial concentration of Cd(II) and their pH were 50 mg/L and 6.0, respectively. Under these conditions, the removal efficiency of Cd(II) reached to 89.3% when the biosorbent dosage was 2.0 g/L. The Langmuir isotherm model correlated with the isotherm data better than the Freundlich isotherm model, and the pseudo-second-order model fitted the kinetic data better than the pseudo-first-order model. These results indicated that the adsorption was monolayer accompanied with chemical adsorption. In the presence of other metal ions, divalent metal ions of Ca and Zn inhibited the performance of Cd(II) biosorption significantly, while Na(I), K(I) and Fe(III) which had a higher or lower valence than Ca(II) affected slightly when containing 50 mg/L Cd(II), 0.5 g/L adsorbent dosage and pH 6.0. The analyses of scanning electron microscopy and Fourier transform infrared spectroscopy illuminated that the biosorbent had porous structures and the amide group was the majorly responsible for Cd(II) removal. Dry biofilms were novel sorbents for effective removal Cd(II), and it could be reused and recycled if necessary.  相似文献   

4.
In this study, sepiolite-nano zero valent iron composite was synthesized and applied for its potential adsorption to remove phosphates from aqueous solution. This composite was characterized by different techniques. For optimization of independent parameters (pH = 3–9; initial phosphate concentration = 5–100 mg/L; adsorbent dosage = 0.2–1 g/L; and contact time = 5–100 min), response surface methodology based on central composite design was used. Adsorption isotherms and kinetic models were done under optimum conditions. The results indicated that maximum adsorption efficiency of 99.43 and 92% for synthetic solution and real surface water sample, respectively, were achieved at optimum conditions of pH 4.5, initial phosphate concentration of 25 mg/L, adsorbent dosage of 0.8 g/L, and 46.26 min contact time. The interaction between adsorbent and adsorbate is better described with the Freundlich isotherm (R 2 = 0.9537), and the kinetic of adsorption process followed pseudo-second-order model. Electrostatic interaction was the major mechanisms of the removal of phosphates from aqueous solution. The findings of this study showed that there is an effective adsorbent for removal of phosphates from aqueous solutions.  相似文献   

5.
The objective of this study was to investigate the biosorption of an azo dye (Methylene blue) by a wetland phytomass (Typha angustata) under post-phytoremediation scenario. Thus, the phytomass was used without any chemical modification. The batch adsorption experiments were conducted to evaluate the effects of contact time and temperatures (25–45 °C) on the adsorption of methylene blue (MB) from aqueous solution by cattail phytomass (CP). More than 80 % of MB dye was removed from the aqueous solution within first 10 min of the experiment. Langmuir isotherm was modeled to describe the monolayer adsorption of MB dye (R 2 = 0.995) with the maximum adsorption capacity of 8.1 mg/g at 25 °C. Pseudo-second-order kinetic model adequately described the kinetics of absorption process (R 2 = 0.999). The adsorption of MB on the cattail phytomass was a spontaneous and endothermic process that was governed by chemisorption. Hence, CP could be applied as a potential low cost biosorbent to treat dyeing wastewater.  相似文献   

6.
Acacia nilotica was used for the adsorption of Reactive Black 5 (RB5) dye from an aqueous solution. Both the raw and activated (with H3PO4) carbon forms of Acacia nilotica (RAN and ANAC, respectively) were used for comparison. Various parameters (including dye concentration, contact time, temperature, and pH) were optimized to obtain the maximum adsorption capacity. RAN and ANAC were characterized using Fourier transform infrared spectroscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The maximum experimental adsorption capacities for RAN and ANAC were 34.79 and 41.01 mg g?1, respectively, which agreed with the maximum adsorption capacities predicted by the Langmuir, Freundlich, and Dubinin–Radushkevich equilibrium isotherm models. The adsorption data of ANAC showed a good fit to the isotherm models based on the coefficient of determination (R 2): Langmuir type II (R 2 = 0.99) > Freundlich (R 2 = 0.9853) > Dubinin–Radushkevich (R 2 = 0.9659). This result suggested monolayer adsorption of RB5 dye. The adsorption of RB5 dye followed pseudo-second-order kinetics. The RAN adsorbent reflected an exothermic reaction (enthalpy change, ΔH = ?0.006 kJ mol?1) and increased randomness (standard entropy change, ΔS = 0.038 kJ mol?1) at the solid–solution interface. In contrast, ANAC reflected both exothermic [?0.011 kJ mol?1 (303–313 K)] and endothermic [0.003 kJ mol?1 (313–323 K)] reactions. However, the ΔS value of ANAC was lower when the RB5 adsorption increased from 313 to 323 K. The negative values for the Gibbs free energy change at all temperatures indicated that the adsorption of RB5 dye onto RAN and ANAC was spontaneous in the forward direction.  相似文献   

7.
This study assesses the ability of two low-cost adsorbents made from waste of Rapanea ferruginea treated with ethanol (WRf) and its H2SO4-treated analog (WRf/H2SO4) for the removal of two cationic dyes methylene blue (MB) and crystal violet (CV) from aqueous solutions. The adsorbent was characterized by scanning electron microscopy, Fourier transform infrared spectrometry, thermogravimetric analysis, point of zero charge (pHpzc), specific surface, and functional groups. The adsorption of dye onto the adsorbents was studied as a function of pH solution (2–12), contact time (up to 120 min) and initial concentration (20–120 mg/L), and temperature (25, 35, and 55 °C). The influence of these parameters on adsorption capacity was studied using the batch process. The response surface methodology (RSM) was used in the experimental design, modeling of the process, and optimizing of the variables and was optimized by the response involving Box–Behnken factorial design (15 runs). The results show that the data correlated well with the Sips isotherm. The maximum adsorption capacities of MB and CV onto WRf were found to be 69 and 106 mg/g, and onto WRf/H2SO4, the adsorption capacities were 33 and 125 mg/g, respectively. The kinetic data revealed that adsorption of cationic dyes onto the adsorbents closely follows the pseudo-second-order kinetic model. Regression analysis showed good fit of the experimental data to the second-order polynomial model, with coefficient of determination (R2) values for MB (R2?=?0.9685) and MB (R2?=?0.9832) for WRf and CV (R2?=?0.9685) and CV (R2?=?0.9832) for WRf/H2SO4 indicated that regression analysis is able to give a good prediction of response for the adsorption process in the range studied. The results revealed that waste from R. ferruginea is potentially an efficient and low-cost adsorbent for adsorption of MB and CV.  相似文献   

8.
The Pb(II) and Ni(II) biosorption of a fungal biomass isolated from mine drainage of metal-processing industries in Balya (Bal?kesir province, Turkey) was optimized using a response surface methodology by altering parameters such as pH, initial metal concentration, contact time and biosorbent dosage. This strain was shown to be highly similar to Penicillium sp. Furthermore, zeta potential measurements and Fourier transform infrared spectroscopy were performed to understand the adsorption mechanism. A Box–Behnken design with 29 experiments was used to evaluate the interactions between independent variables. The results showed that the fungal biomass isolated from the metal mine drainage could have a significant environmental impact through the biosorption of Pb(II) and Ni(II) in waters polluted with heavy metals, particularly in the drainage from metal mines. The maximum removal values were 76 and 47 % at pH 4.5 for both Pb(II) and Ni(II), with 123 and 33 mg/L initial metal concentrations, 65 and 89 min contact times and 0.2 and 1.6 g/L biosorbent, respectively.  相似文献   

9.
Adsorption and desorption of uranium(VI) from dilute aqueous solutions by Eucalyptus citriodora distillation sludge was studied in a batch mode. The potential of Eucalyptus citriodora distillation sludge to remove uranium(VI) from aqueous solutions has been investigated at different conditions of solution pH, metal ion concentrations, biosorbent dosage, biosorbent particle size, contact time and temperature. The results indicated that biosorption capacity of Eucalyptus citriodora distillation sludge was strongly affected by the medium pH, the biosorbent dose, metal ion concentrations and medium temperature. Reduction in particle size increased the biosorption capacity. Langmuir and Freundlich isotherm models were applied to biosorption data to determine the biosorption characteristics. An optimum biosorption capacity (57.75 mg/g) was achieved with pH 4.0, particle size 0.255 mm, biosorbent dose 0.5 g/100 mL and initial uranium(VI) concentration of 100 mg/L. Uranium(VI) removal by Eucalyptus citriodora distillation sludge was rapid, the equilibrium was established within 60 min and pseudo-second-order model was found to fit with the experimental data. The biosorption process decreased with an increase in the temperature indicating its exothermic nature. Pretreatments of biomass with different reagents affected its biosorption capacity. A significant increase (34 %) in biosorption capacity (83.25 mg/g) was observed with benzene treatment. Fourier-transform infra-red studies showed the involvement of carbonyl, carboxyl and amide groups in the biosorption process. The results indicated that sulfuric acid had the best effects as an eluent showing 93.24 % desorption capacity.  相似文献   

10.
This paper investigates the potential of alginate-immobilised Chlorella sorokiniana for removing Cu2+, Ni2+ and Cd2+ ions from drinking water solutions. The effects of initial metal concentrations, contact times and temperatures on the biosorptions and removal efficiencies of the tested metals were investigated at initial pH values of 5, and pH effects were studied within the range of 3–7. When studying the effects of initial metal concentrations, the highest experimental removal yields achieved for Cu2+, Ni2+ and Cd2+ ions were 97.10, 50.94 and 64.61 %, respectively. The maximum biosorption capacities obtained by the Langmuir isotherm model for the biosorptions of Cu2+, Ni2+ and Cd2+ ions by alginate-immobilised C. sorokiniana were found to be 179.90, 86.49 and 164.50 mg/g biosorbent, respectively. The experimental data followed pseudo-second-order kinetics. At an initial metal concentration of 25 mg/L, immobilised algae could be used in at least 5 successive biosorption–desorption cycles. SEM and EDS analyses revealed that the metals bonded to the biosorbent. Bi- and multi-metal systems of Cu2+, Ni2+ and Cd2+ were investigated at initial metal concentrations of 30, 50 and 100 mg/L. The removal of Cd2+ as well as Ni2+ in such systems was negatively affected by the presence of Cu2+. The removal efficiency for Cu2+ in multi-metal systems decreased by 5–7 %, whilst in the cases of Cd2+ and Ni2+ the efficiencies decreased by up to 30 %. Nevertheless, the results obtained show that alginate-immobilised C. sorokiniana can efficiently remove the metals tested from polluted drinking water sources.  相似文献   

11.
In this study, the feasibility of using a low-cost adsorbent mixture composed of leonardite (L) and clinoptilolite (C) was evaluated by batch adsorption method using different parameters such as mixing ratio, contact time, pH, temperature, and adsorbent amount for the removal of Zn (II) ions from an aqueous solution. The adsorbents were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and Raman spectroscopy. Additionally, leonardite–clinoptilolite mixture was analyzed by scanning electron microscopy coupled with energy dispersive X-ray. The Zn (II) adsorption along with an unprecedented adsorption capacity of 454.55 mg g?1 for unmodified natural sorbents was obtained by mixing leonardite and clinoptilolite (LC) without any pretreatment at a ratio of 3:1, using 0.1 g of sorbent at a pH 6, for 2 h of contact time. The experimental data showed a good fit for the Langmuir isotherm model. The thermodynamic parameters revealed that the present adsorption process was spontaneous and exothermic in nature (25–50 °C). The kinetic results of the adsorption showed that the Zn (II) adsorption onto the LC follows pseudo-second-order model. The resultant LC mixture has an excellent adsorption capacity of a Zn (II) aqueous solution, and data obtained may form the basis for utilization of LC as an unpretreated low-cost adsorbent for treatment of metalliferous industrial wastewater.  相似文献   

12.
  相似文献   

13.
Hexavalent chromium has been proved to be the reason of several health hazards. This study aimed at evaluating the application of pomegranate seeds powder for chromium adsorption (VI) from aqueous solution. Chromium adsorption percentage (VI) increased with increasing the adsorbent dosage. Chromium adsorption capacity (VI), at pH = 2 and 10 mg/L initial metal concentration, decreased from 3.313 to 1.6 mg/g through increasing dosage of adsorbent from 0.2 to 0.6 g/100 ml. The adsorption rate increased through increase in chromium initial concentration (VI). However, there was a removal percentage reduction of chromium (VI). Chromium adsorption kinetics by different models (pseudo-first-order, modified pseudo-first-order, pseudo-second-order, Elovich, intraparticle diffusion, Boyd kinetic) was investigated as well. Studies on adsorption kinetic indicated that the experimental data were matched by pseudo-second-order model (R 2 = 0.999) better. Obtained results demonstrated the pomegranate seeds can be used as an effective biomaterial and biosorbent for hexavalent chromium adsorption from aqueous solutions.  相似文献   

14.
In the present work, a continuous catalytic wet peroxide oxidation fixed bed reactor was employed to treat a simulated wastewater sample with malachite green dye, as a contaminant. Natural perlite particle-supported nano-Fe3O4 catalyst was used as a fixed bed inside a reactor, and it was immobilized by a persistent magnetic field. The range of (perlite) particle sizes was from 100 to 1000 nm. The effects of various operating parameters, including temperature of the reactor, pH, initial hydrogen peroxide concentration and initial dye concentration, were investigated on the percentage removal of malachite green dye. Load of catalyst of 2 g and volumetric flow rate of 1 L/h were selected for all the tests. Maximum malachite green degradation was 99.5 ± 0.3%. This removal percentage was attained at temperature of 80 °C, pH = 6, initial dye concentration of 6 mg/L and initial hydrogen peroxide concentration of 100 mg/L. The process was isotherm, and the catalyst showed high catalytic activity in the steady-state condition. The loss of catalyst was less than 0.3%.  相似文献   

15.
The present study reports on the preliminary investigation of three low-cost natural materials with respect to their chromium(VI) removal efficiency from contaminated water. The tested materials were reed, in milled and chopped form, compost, and dewatered sludge from a municipal wastewater treatment plant. The chromium(VI) removal capacity of the aforementioned materials was investigated by simulating the physicochemical conditions prevailing in a stormwater outfall flowing into the Asopos River in Inofyta, Central Greece. Thus, batch and column experiments were carried out using solutions of 3–5 mg/L chromium(VI) and pH value 8.5 ± 0.5. The results showed that the tested materials were capable of removing 3 mg/L chromium(VI), however by allowing different contact times for each material. The chromium(VI) removal kinetics were studied through batch experiments, and reed was found to be the most efficient material. Therefore, at a second series of batch and up-flow column experiments, the effect of the liquid-to-solid ratio, pH, and contact time on chromium(VI) removal using chopped reed was investigated. Chromium(VI) removal took place through both reduction and adsorption mechanisms, while the released soluble organic matter from reed seemed to favor the reduction mechanism. As a result, reed is a potential biosorbent capable of treating heavily chromium(VI)-contaminated water flows, although a high mass of reed is required for a treatment process, such in the case of the stormwater discharged into Asopos River.  相似文献   

16.
The functionalized nano-clay composite adsorbent was prepared, and its properties were characterized using FT-IR, XRD and SEM techniques. The synthesized nano-clay composite was studied with regard to its capacity to remove ibuprofen under different adsorption conditions such as varying pH levels (5–9), initial ibuprofen concentrations (3, 5 and 10 mg L?1), contact time, and the amount of adsorbent (0.125, 0.25, 0.5 and 1 g). In order to evaluate the nanocomposite adsorption capacity, the adsorption results were assessed using nine isotherm models. The results showed that the optimum adsorption pH was 6 and that an increase or decrease in the pH reduced the adsorption capacity. The adsorption process was fast and reached equilibrium after 120 min. The maximum efficacy of ibuprofen removal was approximately 95.2%, with 1 g of adsorbent, 10 mg L?1 initial concentration of ibuprofen, 120 min contact time and pH = 6. The optimal adsorption isotherm models were the Freundlich, Fritz–Schlunder, Redlich–Peterson, Radke–Prausnitz, Sip, Toth and Khan models. In addition, four adsorption kinetic models were employed for adsorption system evaluation under a variety of experimental conditions. The kinetic data illustrated that the process is very fast, and the reaction followed the Elovich kinetic model. Therefore, this nano-clay composite can be used as an effective adsorbent for the removal of ibuprofen from aqueous solutions, such as water and wastewater.  相似文献   

17.
The carbon–alumina composite pellet was developed for the adsorption of acid fuchsin from its aqueous solution. The composite pellet was characterized using Brunauer–Emmett–Teller method, scanning Electron Microscopy and Fourier Transform Infrared Spectroscopy. The adsorption capacity of commercial alumina, commercial activated carbon and the prepared composite pellet was investigated against acid fuchsin, and the adsorption capacity was found to be increased in the order of alumina < carbon–alumina composite pellet < activated carbon. Although the adsorption capacity of carbon–alumina composite pellets was less than that of activated carbon, the use of the pelletized form of the present adsorbent was proven to be advantageous for the use in the packed-bed column. The experimental data were fitted to Langmuir, Freundlich and Temkin adsorption isotherms, and the equilibrium behavior was well explained by Langmuir isotherm. Besides, the kinetic behavior was well predicted by pseudo-second-order kinetics. The effects of inlet dye concentration (10–20 mg/L), feed flowrate (5–15 mL/min) and bed height (2.54–7.62 cm) on the breakthrough characteristics were investigated using a fixed-bed column. The maximum removal capacity in the column study was found to be 343.87 mg/L with an initial dye concentration and flowrate of 20 and 10 mL/min according to Bohart–Adams model. The breakthrough behavior was also effectively described by the Yoon–Nelson and Clark models.  相似文献   

18.
Moringa oleifera seed was used as a biosorbent for the removal of water treatment disinfection by-products, haloethers, trihalomethanes and haloketones from water samples. M. oleifera seed has polar functional groups such as O–H, C=O, C–N and others which facilitate the extraction of these disinfection by-products. Experiments were conducted in batch and fixed bed column modes. Using batch mode, different parameters were optimized such as M. oleifera seed dosage, sample pH, contact time and agitation speed. The effect of the thickness layer and flow rate were also studied using the fixed bed mode. Maximum adsorption occurs using the batch mode with removal efficiencies of 120.5, 114 and 111.5 mg/g for haloethers, trihalomethanes and haloketones, respectively. Adsorption equilibrium followed Langmuir model, and the kinetic data obeyed the pseudo-second-order model, revealing that the M. oleifera seed had higher adsorption capacity than other reported sorbents. Shorter removal time with higher adsorption capacity of disinfection by-products by M. oleifera seed suggests that this material was effective for water treatment, in dealing with the removal of the disinfection by-products considered.  相似文献   

19.
This work reports new findings on the physisorption of Foron Blue 291 on natural bentonite under both static and dynamic flow conditions of the aqueous solution that may prove important when using the adsorption technique for wastewater treatment. The quantity of dye retained by the solid matrix under both ideal exchange conditions between dyes and adsorbents given in a batch reactor and a pulse injection of dissolved azo dye in a soil column composed of a mixture of mean grain-sized sand and bentonite at different flow rates and at various mass fractions of bentonite was studied. Column experiments involving the use of a non-reactive tracer (Fluorescein) were performed to examine hydrodynamic behaviours of the clay/sand mixture studied. It is shown that advective–dispersive transport across a clay/sand mixture may be characterized by a double porosity medium. The results obtained on the reactive transport of Foron Blue 291 underscore that Foron Blue 291 adsorption depends heavily on the mass fraction of clay in a clay/sand mixture. With a clay mass fraction of 30 %, 77 % of the dissolved Foron Blue 291 mass was irreversibly removed by the adsorbent. At low flow rates, removal ratios obtained from the dynamic reactive system were similar to those obtained through previous static reactor experiments.  相似文献   

20.
In this study, the adsorption behavior of Ni(II) in an aqueous solution system using natural adsorbent Peganum harmala-L was measured via batch mode. The prepared sorbent was characterized by scanning electron microscope, Fourier transform infrared spectroscopy, N2 adsorption–desorption and pHzpc. Adsorption experiments were carried out by varying several conditions such as contact time, metal ion concentration and pH to assess kinetic and equilibrium parameters. The equilibrium data were analyzed based on the Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherms. Kinetic data were analyzed using the pseudo-first-order, pseudo-second-order and intra-particular diffusion models. Experimental data showed that at contact time 60 min, metal ion concentration 50 mg/L and pH 6, a maximum amount of Ni(II) ions can be removed. The experimental data were best described by the Langmuir isotherm model as is evident from the high R 2 value of 0.988. The adsorption capacity (q m) obtained was 68.02 mg/g at an initial pH of 6 and a temperature of 25 °C. Kinetic studies of the adsorption showed that equilibrium was reached within 60 min of contact and the adsorption process followed the pseudo-first-order model. The obtained results show that P. harmala-L can be used as an effective and a natural low-cost adsorbent for the removal of Ni(II) from aqueous solutions.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号