首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 93 毫秒
1.
Arsenic(V), as the arsenate (AsO4 3?) ion and its conjugate acids, has a strong affinity on Fe, Mn, and Al (oxyhydr)oxides and clay minerals. Removal of arsenate from aqueous solution by poorly crystalline ferrihydrite (hydrous ferric oxide) via a combination of macroscopic (equilibria and kinetics of sorption) and X-ray absorption spectroscopic studies was investigated. The removal of arsenate significantly decreased with increasing pH and sorption maxima of approximately 1.994 mmol/g (0.192 molAs/molFe) were achieved at pH 2.0. The Langmuir isotherm is most appropriate for arsenate sorption over the wide range of pH, indicating that arsenate sorption preferentially takes place at relatively homogenous and monolayer sites rather than heterogeneous and multilayer surfaces. The kinetic study demonstrated that arsenate sorption onto 2-line ferrihydrite is considerably fast, and sorption equilibrium was achieved within the reaction time of 2 h. X-ray absorption near-edge structure spectroscopy indicates no change in oxidation state of arsenate following interaction with the ferrihydrite surfaces. Extended X-ray absorption fine structure spectroscopy supports the efficient removal of arsenate by the 2-line ferrihydrite through the formation of highly stable inner-sphere surface complexes, such as bidentate binuclear corner-sharing (2C) and bidentate mononuclear edge-sharing (2E) complexes.  相似文献   

2.
The adsorption and desorption of arsenate (As(V)) and arsenite (As(III)) on calcite was investigated in a series of batch experiments in calcite-equilibrated solutions. The solutions covered a broad range of pH, alkalinity, calcium concentration and ionic strength. The initial arsenic concentrations were kept low (<33 μM) to avoid surface precipitation. The results show that little or no arsenite sorbs on calcite within 24 h at an initial As concentration of 0.67 μM. In contrast, arsenate sorbs readily and quickly on calcite. Likewise, desorption of arsenate from calcite is fast and complete within hours, indicating that arsenate is not readily incorporated into the calcite crystal lattice. The degree of arsenate sorption depends on the solution chemistry. Sorption increases with decreasing alkalinity, indicating a competition for sorption sites between arsenate and (bi)carbonate. pH also affects the sorption behavior, likely in response to changes in arsenate speciation or protonation/deprotonation of the adsorbing arsenate ion. Finally, sorption is influenced by the ionic strength, possibly due to electrostatic effects. The sorption of arsenate on calcite was modeled successfully using a surface complexation model comprising strong and weak sites. In the model, the adsorbing arsenate species were and . The model was able to correctly predict the adsorption of arsenate in the wide range of calcite-equilibrated solutions used in the batch experiments and to describe the non-linear shape of the sorption isotherms. Extrapolation of the experimental results to calcite bearing aquifers suggests a large variability in the mobility of arsenic. Under reduced conditions, arsenite, which does not sorb on calcite, will dominate and, hence, As will be highly mobile. In contrast, when conditions are oxidizing, arsenate is the predominant species and, because arsenate adsorbs strongly on calcite, As mobility will be significantly retarded. The estimated retardation factors for arsenate in carbonate aquifers range from 25 to 200.  相似文献   

3.
This paper present the possible alternative removal options for the development of safe drinking water supply in the chromium-affected areas. The Cr (VI) state is of particular concern because of its toxicity. The mordenite has suitable mineralogical properties that enable them to be used for ion-exchange processes. This includes total cation exchange capacity. However, in the present work, the modified-natural zeolite was used as an adsorbent for the removal of Cr (VI) from aqueous solution. The ability of modified natural zeolite (mordenite) to remove inorganic anion was investigated. Laboratory experiments were conducted examining the effect of the sorption of cationic surfactants. On the basis of the results of this study, the HDTMA-HSO4 modified zeolite appears suitable as a sorbent for hexavalent chromium whereas EHDDMA-modified zeolite were not removed with the same efficiency. The sorption of chromate on HDTMA-zeolite results from a combination of entropic, coulombic, hydrophobic effects, and HDTMA counterion.  相似文献   

4.
Recent studies suggest that siderophores form stable complexes with divalent metals and affect their mobility. In this work, effects of trihydroxamate microbial siderophores and desferrioxamine-B (DFOB) on Pb(II), Zn(II), and Cd(II) sorption by two kinds of synthesized zeolites (13X and Na?CY) as a function of pH were investigated. Results showed that 13X zeolite has a higher sorption affinity for studied metals than Na?CY. DFOB strongly affected metal sorption on both zeolites. Under slightly acidic to neutral condition, DFOB increased the metal sorption on zeolites due to the sorption of positively charged heavy metal?CDFOB complexes. Whereas by increasing pH (>7), the mobilizing effect of DFOB was observed for Pb, Zn, and Cd. DFOB drastically decreased (80?%) Zn sorption in alkaline condition. As a result, siderophores can weaken the treatment efficiency of zeolites and increase the bioavailability of metals in soils. Surface complexation modeling revealed that the effects of DFOB on metal sorption by 13X and Na?CY zeolites can be explained by the differences in their surface charge. In general, the result shows the influence of DFOB on metal sorption by zeolites over the pH range 4?C9 and decreasing in the sequence Zn?>?Pb?>?Cd.  相似文献   

5.
The competitive adsorption of arsenate and arsenite with silicic acid at the ferrihydrite–water interface was investigated over a wide pH range using batch sorption experiments, attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy, extended X-ray absorption fine structure (EXAFS) spectroscopy, and density functional theory (DFT) modeling. Batch sorption results indicate that the adsorption of arsenate and arsenite on the 6-L ferrihydrite surface exhibits a strong pH-dependence, and the effect of pH on arsenic sorption differs between arsenate and arsenite. Arsenate adsorption decreases consistently with increasing pH; whereas arsenite adsorption initially increases with pH to a sorption maximum at pH 7–9, where after sorption decreases with further increases in pH. Results indicate that competitive adsorption between silicic acid and arsenate is negligible under the experimental conditions; whereas strong competitive adsorption was observed between silicic acid and arsenite, particularly at low and high pH. In situ, flow-through ATR-FTIR data reveal that in the absence of silicic acid, arsenate forms inner-sphere, binuclear bidentate, complexes at the ferrihydrite surface across the entire pH range. Silicic acid also forms inner-sphere complexes at ferrihydrite surfaces throughout the entire pH range probed by this study (pH 2.8–9.0). The ATR-FTIR data also reveal that silicic acid undergoes polymerization at the ferrihydrite surface under the environmentally-relevant concentrations studied (e.g., 1.0 mM). According to ATR-FTIR data, arsenate complexation mode was not affected by the presence of silicic acid. EXAFS analyses and DFT modeling confirmed that arsenate tetrahedra were bonded to Fe metal centers via binuclear bidentate complexation with average As(V)-Fe bond distance of 3.27 Å. The EXAFS data indicate that arsenite forms both mononuclear bidentate and binuclear bidentate complexes with 6-L ferrihydrite as indicated by two As(III)–Fe bond distances of ∼2.92–2.94 and 3.41–3.44 Å, respectively. The As–Fe bond distances in both arsenate and arsenite EXAFS spectra remained unchanged in the presence of Si, suggesting that whereas Si diminishes arsenite adsorption preferentially, it has a negligible effect on As–Fe bonding mechanisms.  相似文献   

6.
《Applied Geochemistry》1994,9(4):403-412
To improve our understanding of As and Se leaching from fly ash it is necessary to know the underlying geochemical processes. It has been previously suggested that sorption processes may control the partitioning of these trace elements during leaching of fly ash. In natural systems, such as soils and sediments, As and Se have been shown to interact with iron oxides at acidic pH, with CaCO3 at alkaline pH and with clay-minerals at neutral pH. By analogy, we compared the leaching of As and Se from fly ash with the sorption of arsenate and selenite on hematite, portlandite and mullite. It was possible to describe the leaching of As and Se from acidic fly ash with a simplified model of surface complexation with iron oxides. The apparent adsorption constants calculated from the leaching experiments resembled those calculated from our sorption experiments with hematite and values published for amorphous iron oxide. The leaching of As and Se from alkaline fly ash was compared with the sorption of arsenate and selenite on portlandite. A Ca-phase was shown to control the leaching process. Portlandite was shown to be an important sorbent for arsenate and to a lesser extent for selenite, at pH > 12.4. The affinity of arsenate and selenite for mullite was low. Maximum sorption was reached in the neutral pH ranges, similar to the interactions of oxyanions with kaolinite. Sorption reversibility of arsenate on all three minerals considered in this study was less, or at least slower, than that of selenite. This feature may partly explain that the fraction of As available for leaching from fly ash is generally lower.  相似文献   

7.
Uranyl and arsenate cosorption on aluminum oxide surface   总被引：1，自引：0，他引：1  
In this study, we examined the effects of simultaneous adsorption of aqueous arsenate and uranyl onto aluminum oxide over a range of pH and concentration conditions. Arsenate was used as a chemical analog for phosphate, and offers advantages for characterization via X-ray absorption spectroscopy. By combining batch experiments, speciation calculations, X-ray absorption spectroscopy, and X-ray diffraction, we investigated the uptake behavior of uranyl, as well as the local and long-range structure of the final sorption products. In the presence of arsenate, uranyl sorption was greatly enhanced in the acidic pH range, and the amount of enhancement is positively correlated to the initial arsenate and uranyl concentrations. At pH 4-6, U LIII- and As K-edge EXAFS results suggest the formation of surface-sorbed uranyl and arsenate species as well as uranyl arsenate surface precipitate(s) that have a structure similar to trögerite. Uranyl polymeric species or oxyhydroxide precipitate(s) become more important with increasing pH values. Our results provide the basis for predictive models of the uptake of uranyl by aluminum oxide in the presence of arsenate and (by analogy) phosphate, which can be especially important for understanding phosphate-based uranium remediation systems.  相似文献   

8.
The sorption of cadmium and humic acids from aqueous solutions using surface-modified nanozeolite A has been investigated under various examination conditions. The morphology of untreated and treated nanozeolite was studied under scanning electron microscope and transmission electron microscope. Isotherms of cadmium adsorption onto surface-modified nanozeolite A were studied at different pH, solid to liquid ratio, adsorbate concentration and interaction time. Kinetic and equilibrium studies were conducted and the equilibrium data have been analyzed using Langmuir and Freundlich isotherm models. The study revealed that experimental results were in agreement with the Freundlich model. The Langmuir monolayer adsorption capacity was found to be 1666.67 g cadmium and 6.75 g humic acid per gram of modified nanozeolite A, which is higher than that of reported value for other zeolites. The sorption ability was enhanced by surface modification and reduction in size and enabled the zeolite to adsorb cadmium. The adsorption of cadmium and humic acid on nanozeolite was found to be the highest at pH 6 and 3, respectively. Results showed that solid to liquid ratio and pH are the most important factors for cadmium and humic acid removal, respectively. Effect of competitive ions was studied and results showed that there is no competition between cadmium and humic acid sorption and presence of these ions.  相似文献   

9.
In this work, the studies on the formation of zeolites from expanded perlite waste and their use in the sorption process of Cd2+ ions will be reported. Such approach is innovative and has not been investigated elsewhere. The results of the synthesis of zeolites from aluminosilicate waste using hydrothermal method were presented. By-product from the process production of expanded perlite was used as the starting material. Theoretical and practical aspects of Cd2+ ions sorption process onto material synthesized in selected conditions (a material with good sorption capacity can be obtained by 24 h reaction of 1 g of perlite waste in 10 mL of 4.0 M NaOH solution with at 70 °C) will be presented. The atomic absorption spectroscopy has been used as the main method, from which the effective cation exchange capacity as well as the proportion of ion exchange to chemisorption in the sorption process have been determined. Structural analyses of the sample before and after sorption process have been also carried out by the mid-infrared spectra measurement, especially pseudolattice range of the spectra was analyzed in detail in which changes caused by ion exchange of non-tetrahedral ions have been observed.  相似文献   

10.
Migration of uranium and arsenic in aquatic environments is often controlled by sorption on minerals present along the water flow path. To investigate the sorption behaviour, batch experiments were conducted for uranium and arsenic as single components and also solutions containing both uranium and arsenic in the presence of SiO2, Al2O3, TiO2 and FeOOH at a pH ranging from 3 to 9. In solutions containing only U(VI) or As(V) with the minerals, the sorption of U(VI) was low at acidic pH range and increases with increasing pH, whereas As(V) showed opposite sorption behaviour to Al2O3, TiO2 and FeOOH from acidic pH range to alkaline condition. For the As(V)–SiO2 system, the sorption was low for almost all pH. Sorption of U(VI) and As(V) on SiO2 and FeOOH is almost similar in solutions containing either U(VI) or As(V) separately, or both together. In the U(VI)–As(V)–Al2O3 system, a significant retardation in uranyl sorption and an enhancement in arsenate sorption on Al2O3 were observed for a wide range of pH. The sorption behaviour of U(VI) and As(V) was changed when Al2O3 was replaced by TiO2, where an increase in sorption was observed for both elements. The sorption behaviour of uranyl and arsenate in the U(VI)–As(V)–TiO2 system gives evidence for the formation of uranyl–arsenate complexes. The change in sorption retardation/enhancement of U(VI) and As(V) could be explained by the formation of uranyl–arsenate complexes or due to the competitive sorption between uranyl and arsenate species.  相似文献   

11.
考察软阳离子钾改性蒙脱石在K+存在的条件下对硝基苯的强化吸附行为,详细分析比较了Henry和Fre-undlich方程对硝基苯吸附等温线的拟合结果,同时还进行了吸附热力学研究。实验结果表明,软阳离子钾对蒙脱石吸附硝基苯具有强化作用;硝基苯在蒙脱石上的吸附符合Freundlich和Henry方程,两模型方程线性拟合结果的相关系数均在0.96以上。热力学分析结果表明,硝基苯在蒙脱石上的吸附过程是一个自发的放热过程,说明蒙脱石对硝基苯的吸附主要由分配与EDA作用机制所控制。钾离子存在可为硝基苯吸附营造有利场所,不仅改善准入条件,同时增加某些吸附点位,从而促进并强化蒙脱石对硝基苯的吸附。  相似文献   

12.
A laboratory study was executed to investigate the effect of surfactants to enhance sorption of polycyclic aromatic hydrocarbon (PAH) contaminants in loess soil. Phenanthrene and naphthalene were chosen as organic contaminant indicators in loess soil modified by the cation surfactant hexadecyltrimethylammonium (HDTMA) bromide. The kinetic behavior of sorption during transport in natural and modified loess soil was studied. The results indicated that sorption rate in the cation surfactant modified loess soils was at least 3 times faster than that of the natural soil. A first-order kinetics model fitted the sorption data well for both soils. The sorption rates of the two organic compounds were related to their primary residual quantity on the soils. The experiments showed that sorption amounts approached constant values approximately within 30 and 90 min for naphthalene and phenanthrene at 298–318 K, respectively. The rate constants, however, displayed negative correlation with increasing temperature. With changing temperature, the activation energy was calculated at –6.196–1.172 kJ/mol for naphthalene and –28.86–15.70 kJ/mol for phenanthrene at 298–318 K. The results can be used to predict the sorption kinetics of phenanthrene and naphthalene in loess soils, and in a wider perspective, be used to better understand the transport of petroleum contaminants in the soil environment.  相似文献   

13.
The aim of this work was to investigate the effects of sorbent (natural and modified zeolite and bentonite, iron filings and ferric sulfate) on the speciation and bioavailability of arsenic in contaminated soil. The soil used in this experiment was collected from Zarshuran area (Western Azerbaijan province, NW Iran). The sorbents were added to the soil in various rates separately. After a month of incubation, sunflower was planted in pots. After harvest, soil and plant samples of each pot were analyzed. Then various species of arsenic were estimated in soil solutions by MINTEQ software program. Water-soluble arsenate, arsenite and exchangeable arsenic from each pot measured. The results showed that the sorbents had no effect on the speciation of arsenic. Mobility of arsenite in the soil solutions has not changed. Soils treated with natural bentonite and zeolite increased soluble arsenate concentration and decreased exchangeable arsenic concentration. Although Fe-zeolite increased soluble arsenate concentration, Fe-bentonite, iron filings and ferric sulfate decreased soluble arsenate concentration and exchangeable arsenic concentration. Finally, iron filings (containing 354 mmol Fe+3) vigorously increases in the plants biomass and decreases in the arsenic concentration in plants tissue, is suggested as the best sorbent for arsenic stabilization in the region.  相似文献   

14.
Fourier transformed infrared (FTIR) spectroscopy was used to characterize arsenate-ferrihydrite sorption solids synthesized at pH 3-8. The speciation of sorbed arsenate was determined based on the As-O stretching vibration bands located at 650-950 cm−1 and O-H stretching vibration bands at 3000-3500 cm−1. The positions of the As-O and O-H stretching vibration bands changed with pH indicating that the nature of surface arsenate species on ferrihydrite was strongly pH dependent. Sorption density and synthesis media (sulfate vs. nitrate) had no appreciable effect. At acidic pH (3, 4), ferric arsenate surface precipitate formed on ferrihydrite and constituted the predominant surface arsenate species. X-ray diffraction (XRD) analyses of he sorption solids synthesized at elevated temperature (75 °C), pH 3 clearly showed the development of crystalline ferric arsenate (i.e. scorodite). In neutral and alkaline media (pH 7, 8), arsenate sorbed as a bidentate surface complex (in both protonated FeO2As(O)(OH)− and unprotonated forms). For the sorption systems in slightly acidic media (pH 5, 6), both ferric arsenate and surface complex were probably present on ferrihydrite. It was further determined that the incorporated sulfate in ferrihydrite during synthesis was substituted by arsenate and was more easily exchangeable with increasing pH.  相似文献   

15.
Natural ferrihydrites (Fh) often contain impurities such as aluminum, especially in acid mine drainage, and these impurities can potentially impact the chemical reactivity of Fh with respect to metal (loid) adsorption. In the present study, we have investigated the influence of aluminum on the sorption properties of ferrihydrite with respect to environmentally relevant aqueous arsenic species, arsenite and arsenate. We have conducted sorption experiments by reacting aqueous As(III) and As(V) with synthetic Al-free and Al-bearing ferrihydrite at pH 6.5. Our results reveal that, when increasing the Al:Fe molar ratio in Fh, the sorption density dramatically decreased for As(III), whereas it increased for As(V). Extended X-ray Absorption Fine Structure (EXAFS) spectroscopy analysis at the As K-edge indicated that the AsIIIO3 pyramid binds to FeO6 octahedra on both Al-free Fh and Al-bearing Fh, by forming bidentate mononuclear edge-sharing (2E) and bidentate binuclear corner-sharing (2C) surface complexes characterized by As–Fe distances of 2.9 Å and 3.4 Å, respectively. The decrease in As(III) sorption density with increasing Al:Fe ratio in Fh could thus be explained by a low affinity of the As(OH)3 molecule for Al surface sites compared to Fe ones. In contrast, on the basis of available literature on As(V) adsorption mechanisms, we suggest that, in addition to inner-sphere 2C arsenate surface complexes, outer-sphere arsenate surface complexes forming hydrogen bonds with both Al–OH and Fe–OH surface sites could explain the enhancement of As(V) sorption onto aluminous Fh relative to Al-free Fh, as observed in the present study. The presence of aluminum in Fh may thus enhance the mobility of arsenite with respect to arsenate in Acid Mine Drainage impacted systems, while mixed Al:Fe systems could present an alternative for arsenic removal from impacted waters, provided that As(III) would be oxidized to As(V).  相似文献   

16.
Arsenic is a ubiquitous element in the environment and occurs naturally in both organic and inorganic forms. Under aerobic condition, the dominant form of arsenic in waters is arsenate, which is highly mobile and toxic. Arsenic poisoning from drinking water remains a serious world health issue. There are various standard methods for arsenic removal from drinking waters (coagulation, sorption, ion-exchange reactions or methods of reverse osmosis) and alternative methods, such as biosorption. Biosorption of arsenic from natural and model waters by native or chemically modified (with urea or ferric oxyhydroxides) plant biomass prepared from sawdust of Picea abies was studied. The kinetic of the adsorption process fitted well the pseudo second order adsorption model and equilibrium was achieved after 2 h. The results showed that biosorption was well described by both Langmuir and Freundlich isotherms. The maximum biosorption capacity of the sawdust modified with ferric oxyhydroxides, evaluated by Langmuir adsorption model, was 9.259 mg/g, while the biosorption capacity of unmodified biosorbent or biosorbent modified with urea was negligible. The adsorption capacity is comparable to results published by other authors, suggesting that the prepared chemically modified biosorbent has potential in remediation of contaminated waters.  相似文献   

17.
《Applied Geochemistry》2003,18(10):1507-1515
Adsorption studies have been conducted at pH 4, 6 and 8 to assess the effect of fulvic acid on arsenate adsorption to ferrihydrite and gibbsite. The studies compared the adsorption of arsenate on the mineral surfaces in the absence of fulvic acid, to those cases where increasing concentrations of fulvic acid (0.3–60 μM) were added to the mineral–arsenate suspensions. Experiments where arsenate was added to mineral–fulvate suspensions were also conducted. The results suggest that arsenate adsorption on both gibbsite and ferrihydrite decreases with increasing concentrations of fulvic acid. This effect was highest at pH 4, and decreased at pH 6 and 8. Ferrous ion concentrations were very low during the ferrihydrite experiments and support the view that fulvic acid can both displace arsenate from and inhibited its adsorption to mineral surfaces. The experiments also indicated that the amount of arsenate adsorbed was lower if fulvic acid was added before rather than after arsenate. This may reflect the relative size of arsenate and fulvic acid molecules and their ability to penetrate the crystal matrices of the minerals.  相似文献   

18.
采用NaOH对围场地区天然沸石进行处理,采用X射线衍射仪、红外光谱仪、N2吸附-脱附技术、扫描电子显微镜等对材料进行表征分析,采用水蒸气吸附法评价材料的亲水性,采用Cr3+和Mn2+评价材料的离子交换性能,探讨了碱处理对天然沸石的结构、亲水性和离子交换性能的影响及其机理.实验结果表明,围场地区天然沸石中主要含有斜发沸石...  相似文献   

19.
Inorganic elements analyses of Carapicuíba lake reveal that As, Cr, Pb and Mn are above the recommended drinking water standards. The mean total concentrations of toxic elements in surface water decrease in the order Mn > Cr > Pb > As. At elevated concentrations, toxic elements like Cr can accumulate in soils and enter the food chain, leading to serious health hazards and threatening the long-term sustainability of the local ecosystem. Absorbing materials has often been used to improve water quality. In this investigation three types of material were studied: the natural zeolite (mordenite); synthetic goethite and the powdered block carbon modified. The adsorption of Pb2+ and Mn2+ onto natural zeolite as a function of their concentrations was studied at 24°C by varying the metal concentration from 100 to 400 mg L−1 while keeping all other parameters constant. The low-cost zeolites removed Pb from water without any pretreatment at pH values <6. The maximum adsorption attained was as follows: Pb2+ 78.7% and Mn2+ 19.6%. The modified powdered block carbon effectively removed As(V) and Cr(VI) while goethite removed more chromate than arsenate in the pH range 5–6. Results of this study will be used to evaluate the application these materials for the treatment of the Carapicuíba lake’s water.  相似文献   

20.
Reaction-based modeling of quinone-mediated bacterial iron(III) reduction   总被引：1，自引：0，他引：1  
This paper presents and validates a new paradigm for modeling complex biogeochemical systems using a diagonalized reaction-based approach. The bioreduction kinetics of hematite (α-Fe2O3) by the dissimilatory metal-reducing bacterium (DMRB) Shewanella putrefaciens strain CN32 in the presence of the soluble electron shuttling compound anthraquinone-2,6-disulfonate (AQDS) is used for presentation/validation purposes. Experiments were conducted under nongrowth conditions with H2 as the electron donor. In the presence of AQDS, both direct biological reduction and indirect chemical reduction of hematite by bioreduced anthrahydroquinone-2,6-disulfonate (AH2DS) can produce Fe(II). Separate experiments were performed to describe the bioreduction of hematite, bioreduction of AQDS, chemical reduction of hematite by AH2DS, Fe(II) sorption to hematite, and Fe(II) biosorption to DMRB. The independently determined rate parameters and equilibrium constants were then used to simulate the parallel kinetic reactions of Fe(II) production in the hematite-with-AQDS experiments. Previously determined rate formulations/parameters for the bioreduction of hematite and Fe(II) sorption to hematite were systematically tested by conducting experiments with different initial conditions. As a result, the rate formulation/parameter for hematite bioreduction was not modified, but the rate parameters for Fe(II) sorption to hematite were modified slightly. The hematite bioreduction rate formulation was first-order with respect to hematite ”free“ surface sites and zero-order with respect to DMRB based on experiments conducted with variable concentrations of hematite and DMRB. The AQDS bioreduction rate formulation was first-order with respect to AQDS and first-order with respect to DMRB based on experiments conducted with variable concentrations of AQDS and DMRB. The chemical reduction of hematite by AH2DS was fast and considered to be an equilibrium reaction. The simulations of hematite-with-AQDS experiments were very sensitive to the equilibrium constant for the hematite-AH2DS reaction. The model simulated the hematite-with-AQDS experiments well if it was assumed that the ferric oxide “surface” phase was more disordered than pure hematite. This is the first reported study where a diagonalized reaction-based model was used to simulate parallel kinetic reactions based on rate formulations/parameters independently obtained from segregated experiments.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号