共查询到19条相似文献，搜索用时 593 毫秒
1.
2.
地基条件和墙高是影响挡土墙地震响应特征的重要因素。建立不同地基条件的仰斜式挡土墙有限元时程分析模型,以墙身外倾最大危险状态为最不利时刻,研究地基条件和墙高对挡墙动力响应及墙-土相互作用的影响特征,并以满足力学检算和墙身位移限值为出发点,提出同时考虑地基条件和地震峰值加速度PGA的仰斜式挡墙墙高控制建议。结果表明：岩质地基挡墙墙背动土压力沿墙高呈中部大、上下小的凸形分布,大震下土压力较中震时有小幅减小;基底反力呈墙踵为0、墙趾集中的三角形图式,且随PGA和墙高的增加踵部脱空趋势更为明显;土质地基挡墙因墙底地基土变形对墙后填土的牵连作用,填土跟随墙身运动的趋势加剧,墙背动土压力与PGA呈正相关并沿墙高近似呈线性分布,于墙底处最大;墙身往复摆动使踵趾端地基土体塑性变形较基底中部明显,基底反力峰值向中部转移;根据最不利时刻稳定性、承载力检算,考虑对墙身位移合理限制,提出地震区仰斜式挡墙的允许墙高在设防PGA不超过0.2g时为8 m, 0.4g大震下硬质岩地基挡墙可达8 m,软质岩地基挡墙不宜超过6 m,碎石土、砂质黏土地基挡墙不宜超过4 m。 相似文献
3.
土质场地重力式挡土墙地震土压力振动台实验研究 总被引：3，自引：0，他引：3
汶川震区路基挡土墙震害表明,地震动荷载作用下重力式挡墙的位移、破坏与基础场地形式有关,除岩质场地和土质场地挡墙所共有的外倾形式,土质地基挡土墙还表现有整体推移及下部向外推移的倾转变形等复杂模式,因此地震土压力大小及分布也将受到这种复杂土-结相互作用的影响。基于碎石土及风化花岗岩填料的土质场地重力式挡土墙大型振动台模型实验,对挡土墙地震土压力及变形模式开展了对比研究,发现在强震作用下,土质地基挡墙因基础约束较弱而产生位移,并伴随明显的墙—土分离现象,致使实测地震土压力较之抗震设计规范计算值偏小（0.4g峰值加速度下约小6%～15%）,但作用点高度变化不大。由实验结果与现行抗震规范计算值的安全系数对比,认为对土质场地挡墙的地震土压力计算,按现行国内抗震设计规范基本能满足实际工程抗震设计需要;对于地震区挡墙设计,在允许挡墙发生少量容许位移的前提下可采用内摩擦角较大、自稳能力更好的墙背填料以减少地震土压力。 相似文献
4.
5.
岩石场地重力式挡土墙地震土压力振动台实验研究 总被引：5，自引：0，他引：5
结合汶川震区调查资料,利用大型振动台模型试验,分析了碎石土填料的岩石场地重力式挡土墙的地震土压力及其分布规律,并以此对我国现行铁路、公路抗震规范做合理性讨论和细化。研究发现,地震作用下,挡土墙的动土压力沿墙高呈单峰曲线状分布,且60%～80%集中作用于挡墙中部;随着地震峰值加速度的增加,地震土压力分布逐渐偏离现行振震设计规范所认为的三角形线性状,而呈现非线性状;合力作用点高于1/3墙高,0.4g地震加速度作用下,接近0.4倍墙高,对岩石场地下粗粒径墙背填料的地震土压力作用点高度,建议取0.35倍墙高。对比计算表明,现行规范能基本满足工程抗震设计需要,但建议对柔性挡土墙的抗震设计作出必要规定。 相似文献
6.
研究直立式加筋土挡墙抗震性能时,采用的NCMA方法未全面运算其墙外功率,抗震性能分析结果存在较高偏差。采用极限分析的方法对直立式加筋土挡墙破坏模式展开极限分析,得到该挡墙运动极限表达式。根据运动极限表达式,对一实例墙体计算出此挡墙外功率(包括土重所做的外功率和地震作用所做的外功率),分析其抗震性能。实验结果表明,计算得到直立式加筋土挡墙各层筋材最大外功率分别为18.5 kN·m和20 kN·m,与实际最大外功率18 kN·m差距不大,说明该方法的抗震性能分析与实际情况相符,具有应用性。 相似文献
7.
地震土压力评价是挡土墙抗震设计的关键问题之一.以往的研究结果表明,挡墙上地震土压力的大小及分布与墙体的侧向位移或者墙后填土的侧向变形密切相关.经典的物部-冈部地震土压力公式可计算填土处于主动与被动状态的极限平衡条件下的土压力,未考虑挡墙侧向位移或填土侧向变形对土压力的影响.在研究土压力系数随应变增量比变化规律的基础上,本文指出土压力系数与挡土墙位移量之间不存在唯一性关系,发现正常固结填土的土压力系数与以应变增量比表述的填土侧向应变约束条件之间具有良好的唯一性,揭示了压剪耦合效应是土压力形成的物理本质;基于上述的唯一性关系和中间土楔等概念,提出了可考虑填土侧向变形的地震土压力实用计算方法,并通过土压力模型试验结果初步验证了该方法的合理性. 相似文献
8.
《世界地震工程》2016,(2)
二级悬臂式挡墙由2个单级悬臂式挡墙呈上下砌垛方式组成。该结构不仅具有单级挡墙型式简单、占地少、对地基承载力要求不高、经济指标好和施工方便等一系列的特点,而且弥补了单级挡墙限制高度的缺点,同时具有重力式挡墙的一些优点,在工程中逐步得到了应用。以库伦土压力理论为基础结合物部-冈部法分别计算了峰值加速度为0.2g、0.3g和0.4g时,二级悬臂式挡墙在分级墙背理论和整体墙背理论下,上墙和下墙的地震主动土压力,并与同高度的单级悬臂式挡墙地震土压力进行了比较。结果表明:二级悬臂式挡墙受力更优,是1种较优的抗震支挡结构,分析结果可为二级悬臂式挡土墙的抗震设计提供参考。 相似文献
9.
地震作用下模块式加筋土挡墙极易发生墙面模块脱落破坏,针对模块面板与筋材的连接稳定问题开展理论分析,用于模块式加筋土挡墙面板连接抗震安全设计。基于极限平衡法,通过考虑筋材与面板间的连接强度和连接抵抗力,提出了地震条件下面板连接稳定性分析方法。运用本文提出的方法进行了一系列参数分析,研究了水平地震力、竖向地震力、加筋间距以及墙趾阻力等因素对面板连接稳定性的影响。研究结果表明：水平和竖向联合地震作用极易导致加筋挡墙面板连接破坏,减小墙趾阻力和增加加筋间距使加筋挡墙面板净连接力减小,且对挡墙下部筋材更加显著。因此,加筋土挡墙抗震安全设计需要注意近断层场地中竖向地震作用,同时加筋间距不宜过大。 相似文献
10.
重力式挡土墙在地震作用下的土压力特性一直是挡土墙设计的重要内容。本文通过数值模拟,在挡土墙墙背轴线上设置一系列监测点,得到地震过程中监测点的加速度、土压力强度时程曲线;然后根据时程曲线分析墙后土压力强度分布特征、根据土压力强度分布求出总土压力、根据总土压力求出其对墙趾的力矩;最后分别将土压力强度分布、总土压力、总土压力对墙趾的力矩与现有的研究方法及规范对比。结果表明:地震作用下墙背各点加速度峰值在同时刻发生,但土压力峰值不在同时刻发生;现有的一些研究方法未考虑土压力强度峰值时程变化,其结果比实际偏大;在低地震烈度条件下,规范计算的总土压力及倾覆力矩偏于保守,而在高烈度条件下则偏于危险。 相似文献
11.
Seismic rotational displacement of gravity walls by pseudo-dynamic method: Passive case 总被引：8，自引：0，他引：8
Prediction of the seismic rotational displacements of retaining wall under passive condition is an important aspect of design in earthquake prone region. In this paper, the pseudo-dynamic method is used to compute the rotational displacements of rigid retaining wall supporting cohesionless backfill under seismic loading for the passive earth pressure condition. The proposed method considers time, phase difference and effect of amplification in shear and primary waves propagating through both the backfill and the retaining wall. The influence of ground motion characteristics on rotational displacement of the wall is evaluated. Also the effects of variation of parameters like wall friction angle, soil friction angle, amplification factor, shear wave velocity, primary wave velocity, period of lateral shaking, horizontal and vertical seismic accelerations on the rotational displacements are studied. The rotational displacement of the wall increases substantially with increase in amplification of both shear and primary waves, time of input motion, period of lateral shaking and decreases with increase in soil friction angle, wall friction angle. The rotational displacements of the wall also increase when the effect of wall inertia is taken into account. Results are provided in graphical form. 相似文献
12.
挡土墙地震被动土压力的拟动力分析 总被引：5，自引：0，他引：5
对地震土压力的研究是地震区挡土墙安全设计的一项重要课题。地震条件下,目前的研究主要是给出了土压力的近似拟静力解析解。本文采用可考虑动力荷载下的周期和纵波及横波效应的拟动力方法,对挡土墙后的地震被动土压力进行分析。在挡土墙后平面滑裂面假设的基础上,考虑了水平和垂直向地震加速度、纵波速度、横波速度、挡土墙摩擦角、填土内摩擦角、填土坡角对地震被动土压力的影响。与Mononobe-Okabe理论的拟静力法不同的是,用本方法得出了沿墙身地震被动土压力是非线性变化的结果,这更符合地震条件下土压力的变化规律。 相似文献
13.
高烈度地震区重力式挡土墙由于地基承载力不足导致墙身失稳是一种较常见震害类型。基于拟静力法原理,利用极限分析上限定理对地震作用下挡土墙地基极限承载力进行求解,通过典型算例分析了极限承载力随地震动峰值加速度的变化关系与机理,讨论了地基土强度参数对其变化趋势的影响,提出了同时考虑设防烈度和地基土性的挡土墙地基抗震容许承载力修正方法及相应修正系数取值建议。结果表明:设防烈度在9度及以内时,随着地震动峰值加速度增加,挡土墙地基极限承载力近似呈线性下降,下降速率与地基土黏聚力呈负相关性,而受内摩擦角的影响不显著;地震作用加剧挡土墙基底荷载倾斜与偏心导致地基破坏区缩减是造成极限承载力下降的主要原因;设防烈度大于7度时,挡土墙地基抗震容许承载力较天然工况下有所降低,8度和9度设防烈度对应的修正系数约为0.9和0.7。 相似文献
14.
Seismic passive resistance with vertical seepage and surcharge 总被引：1，自引：0，他引：1
Jun-Jie Wang Hui-Ping Zhang He-Jun Chai Jun-Gao Zhu 《Soil Dynamics and Earthquake Engineering》2008,28(9):728-737
Present paper focuses on the computation of the seismic passive earth pressure acting on a vertical rigid retaining wall by a soil mass subjected to vertical steady-state seepage and a uniform surcharge load. Based on the basic assumptions of Coulomb's theory and a pseudo-static method of analysis, a general solution for the passive earth pressure containing two coefficients is presented. In the solution, many parameters, such as unit weight of saturated soil, soil effective internal friction angle, soil/wall friction angle, water/soil unit weight ratio, surcharge intensity coefficient, horizontal and vertical seismic acceleration coefficients, Poisson's ratio of soil mass, hydraulic gradient, and coefficients of pore water pressure, are considered. The effects of hydraulic gradient and seismic forces on passive earth pressure coefficient and passive earth pressure distribution are investigated. The results indicate that passive earth pressure increases with increasing hydraulic gradient for downward water flow case, but decreases for upward water flow case, and that the presence of seismic forces induces a reduction in passive earth pressure. 相似文献
15.
土工格栅加筋挡土墙是一种柔性挡土结构,目前尚未建立较严密的设计方法,作用在土工格栅加筋墙壁上的地震动土压力研究是抗震设计的重要内容之一。应用基于拉格朗日法的完全非线性动有限差分法研究整体面板式土工格栅加筋土挡壁在地震作用下各设计参数对挡壁动土压力的影响。采用弹塑性模型模拟填土,采用耦合弹性参数描述格栅与土接触界面特性,参数包括加筋间距、长度、刚度、地震强度和填土性质等,分析墙壁的动土压力沿墙身的分布特征,得出了影响地震动土压力的显著参数,证明了土工格栅加筋墙体的优异吸震能力,研究结果为整体面板式土工格栅加筋土挡墙抗震设计中的动土压力研究提供参考。 相似文献
16.
Pseudo-dynamic active force and pressure behind battered retaining wall supporting inclined backfill
Knowledge of seismic active earth pressure behind rigid retaining wall is very important. Commonly used Mononobe–Okabe method considers pseudo-static approach, which gives the linear distribution of seismic earth force. In this paper, the pseudo-dynamic approach, which considers the effect of primary and shear wave propagations, is adopted to calculate the seismic active force. Considering the planar rupture surface, the effect of wide range of parameters like inclination of retaining wall, inclination of backfill surface, wall friction and soil friction angle, shear wave and primary wave velocity, horizontal and vertical seismic coefficients are taken into account to evaluate the seismic active force. Results are presented in terms of seismic coefficients in tabular form and variation of pressure along the depth. 相似文献
17.
依托湖南省湘潭至衡阳西线高速公路K 124＋300～K 124＋895段国内首座加筋格宾组合式挡土墙工程,介绍了以双绞合六边形金属网为筋材的2种新型加筋支挡结构：加筋格宾结构与绿色加筋格宾结构;以极限平衡理论为基础,吸收国外先进加筋土技术,提出了该组合结构的稳定性验算方法与公式;编制相关程序,深入研究了填料粘聚力、内摩擦角、网面拉力、地震力、填土重度、车辆荷载以及加筋间距等重要参数对安全系数的影响。研究表明,各设计参数对安全系数的影响程度不同。同时,也验证了该加筋格宾组合式挡土墙设计的科学性和合理性。研究成果可应用于具体支挡结构设计。 相似文献
18.
The static and seismic sliding limit equilibrium condition of retaining walls is investigated, and analytical solutions for the angle of the active slip surface, the critical acceleration coefficient and the coefficient of active earth pressure are provided for different surcharge conditions. In particular, walls retaining a horizontal backfill without surcharge, walls supporting an extended uniform surcharge applied at different distances from the wall and walls supporting a limited uniform surcharge or linear uniform surcharge parallel to the wall are considered in the analysis.The solutions have been derived in the framework of the limit equilibrium approach, considering the effect of the wall through its weight, and accounting for the shear resistance at the base of the wall and the inertia force arising in the wall under seismic conditions.For the wall without surcharge the effect of the vertical component of the seismic acceleration as well as the effects of the inclination of the wall internal face and of the soil–wall friction were also investigated.The angle of the slip plane, the critical seismic acceleration coefficient and the coefficient of active earth pressure are given as functions of dimensionless parameters and the boundary conditions for the applicability of each solution are specified. The influence of soil weight, surcharge conditions and inertia forces on the active earth pressure coefficient is analysed. 相似文献
19.
Evaluating the seismic active earth pressure on retaining walls is currently based on pseudo-static method in practices. In this method, however, it is not simple, choosing an appropriate value for earthquake coefficient, which should fully reflect the dynamic characteristics of both soil and loading is an important problem. On the other hand, by using only two extra dynamic parameters that are shear wave velocity of soil and predominant frequency of probable earthquake, one can benefit from another more accurate tool called pseudo-dynamic method to solve the problem of earth pressure.In this study in the framework of limit equilibrium analysis, pseudo-dynamic method has been applied into horizontal slice method of analysis to account for the effect of earthquake on lateral earth pressure history behind rigid retaining walls. The pressure history resulted from a number of analyses shows that before and after reaching the peak resultant force, different pressure distributions occur behind a wall that put more local pressure than the same at peak. This method would be a tool to control this phenomenon in wall design. 相似文献