首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 46 毫秒
1.
针对雁木西油田白垩系低阻油层受沉积相带及其断裂、构造和岩性等多种因素控制影响,测井信息应用难度增大的特点,采用地层倾角测井资料确定古水流方向、砂体延伸、层理构造和微相特征.利用倾角方位频率矢量统计,确定出白垩系K1s3、K1s2、K1s1目的层段古水流及其相应河道砂体延伸方向为北北东20°.利用层理构造倾角模式分析,确定出白垩系K1s3、K1s2、K1s1期分别发育楔状交错层理、波状斜层理、波状交错层理和水平层理,结合岩心、井径、自然伽马和微侧向电阻率曲线特征,分别阐明白垩系K1s3、K1s2到K1s1期水动力能量由较高到较低变化,形成了扇三角洲前缘扇中的水下辫状河道到扇端的浅水河道有利微相砂体发育带,它们由南南西向北北东方向展布,控制着研究区最为有利的油气储集砂体分布.  相似文献   

2.
利用宁夏区域地震台网的波形数据,基于三种不同速度模型分别使用相对稳定的 Hash方法、Snoke方法及gCAP方法计算2017年9月2日宁夏固原 MS4．6地震的震源机制解,并根据这些结果给出了该地震的震源机制中心解.结果表明,该地震的震源机制中心解为节面Ⅰ:走向: 41°,倾角:79°,滑动角:-175°;节面Ⅱ:走向:310°,倾角:85°,滑动角:-11°.基于速度模型3的Hash方法结果和中心解结果之间的最小空间旋转角数值相对最小,震源机制解参数最接近中心解的结果.速度模型分层越精细,结果的精度相对越高,其中 Hash方法及Snoke方法的反演结果受速度模型的影响较为明显,与 Snoke方法相比,Hash方法对台站分布的要求较低,但对波形质量要求较高,要确保整个波形段和剪切波段具有一定范围的高信噪比.在实际应用中,对于台站方位角覆盖不是很好的区域地震台网来说,或者地震震中位于台站分布相对稀少的地区且可利用台站数目不是很多的情况下,在精细速度模型和波形信噪比的阈值等参数设置较为准确的情况下,可以考虑使用 Hash方法来丰富计算结果.  相似文献   

3.
本文以海原断裂带区域活动构造为基础,将海原断裂划分为西、中、东3段.基于1999年12月26日至2010年7月26日间的精定位小震目录,估计了海原断裂带各段的倾角.考虑海原断裂沿走向可能存在南倾与北倾两种情况,将倾角的范围设置为.首先运用网格搜索法确定了平面断层模型,其次以特征深度节点为基础数据运用多项式构建了曲面断层模型.结果表明：当进行平面拟合时,海原断裂西段与中段、东段的倾向不同,西段为南倾,其倾角值为71°,而中段、东段为北倾,其倾角值分别为72°、65°,各段的倾角值均由地表以下8 km地震资料确定.当进行曲面拟合时,在8 km深度以内海原断裂西段、中段、东段的倾角均处于80°左右,即接近陡立.西段的倾角在深度为9 km处出现转换,之后倾角接近陡立;中段的倾角在深度为16 km处出现转换,之后倾角逐渐减小,当深度为18 km时倾角为30°;东段的倾角在深度为11 km处出现转换,倾角为42°,在深度为16 km处出现第二次转换,倾角为55°,之后倾角逐渐减小.结合震源机制解和大地测量观测资料反演拟合的合理性,验证了本文所估计倾角的可靠性.  相似文献   

4.
In an attempt to understand the structure of active faults as they emerge from bedrock into shallow semi-consolidated and unconsolidated sediments, we have recorded a comprehensive high-resolution seismic reflection/refraction data set across the Ostler Fault zone on the central South Island of New Zealand. This fault zone, which absorbs 1–2 mm/yr of compression associated with oblique convergence of the Pacific and Australian tectonic plates, consists of a series of surface-rupturing N–S trending, west-dipping reverse faults that offset a thick sequence of Quaternary glacial outwash and late Neogene fluvio-lacustrine sediments of the Mackenzie Basin. Our study focuses on a region of the basin where two non-overlapping fault segments are separated by a transfer zone. Deformation in this area is accommodated by offsets on multiple small faults and by folding in their hanging walls. The seismic data with source and receiver spacing of 6 and 3 m and nominal CMP fold of 60 was acquired along twelve 1.2 km long lines orthogonal to fault strike and an additional 1.6 km long tie-line parallel to fault strike. The combination of active deformation and shallow glacial outwash sediments results in particularly complicated seismic data, such that application of relatively standard processing schemes yields only poor quality images. We have designed a pre- and post-stack reflection/refraction processing scheme that focuses on minimising random and source-generated noise, determining appropriate static corrections and resolving contrasting reflection dips. Application of this processing scheme to the Ostler Fault data provides critical information on fault geometry and offset and on sedimentary structures from the surface to ～ 800 m depth. Our preliminary interpretation of one of the lines includes complex deformation structures with folding and multiple subsidiary fault splays on either side of a ～ 50° west-dipping primary fault plane.  相似文献   

5.
Different mountain shapes in sedimentary sequences in the Canadian Rockies were enhanced by glacial erosion and have been modified postglacially by gravity-driven slope processes. Slope modification by both glacial erosion and postglaciation landslides is related to rock structure, particularly bedding dip, rock mass strength and slope geometry. Five mountain peak shapes in monoclinal sequences each fall into different ranges of bedding dips. Castellate (1) and matterhorn (2) mountains occur in sub-horizontal beds and their slopes on all sides follow combinations of bedding planes and joints. The overall slopes are generally 37 to 65° and oblique to both bedding and joints. Slopes in sub-horizontal beds may be controlled by their rock mass strength. Cuestas (3) develop in gently to moderately dipping beds. Dip slopes and steeper, normal escarpments form their cataclinal and anaclinal sides respectively, with the dihedral angle between them about 90°. Hogbacks (4) in moderately to steeply dipping beds have similar slope angles on both cataclinal and anaclinal slopes. Cataclinal slopes are either dip slopes or underdip slopes but anaclinal slopes are often steepened escarpments; the dihedral angle between the slopes is usually less than 90°. Dogtooth (5) mountains occur in steeply dipping to sub-vertical beds and the dihedral angle can be as low as 60°. Slope gradients in inclined beds are closely related to landslides, whose modes are controlled by bedding dips. Copyright © 1999 John Wiley & Sons, Ltd.  相似文献   

6.
To better image deformation structures within the inner accretionary wedge of the Nankai Trough, Japan, we apply common reflection angle migration to a legacy two-dimensional seismic data set acquired with a 6 km streamer cable. In this region, many seismic surveys have been conducted to study the seismogenic zone related to plate subduction. However, the details of the accreted sediments beneath the Kumano forearc basin are still unclear due to the poor quality of seismic images caused by multiple reflections, highly attenuated signals, and possibly complex geological structures. Generating common image gathers in the subsurface local angle domain rather than the surface offset domain is more advantageous for imaging geological structures that involve complex wave paths and poor illumination. By applying this method, previously unseen structures are revealed in the thick accreted sediments. The newly imaged geometric features of reflectors, such as the folds in the shallow part of the section and the deep reflectors with stepwise discontinuities, imply deformation structures with multiple thrust faults. The reflections within the deep accreted sediments (approximately 5 km) are mainly mapped to far angles (30°–50°) in the common reflection angles, which correspond to the recorded offset distances greater than 4.5 km. This result indicates that the far offset/angle information is critical to image the deformation structures at depth. The new depth image from the common reflection angle migration provides seismic evidence of multiple thrust faults and their relationship with the megathrust fault that is essential for understanding the structure and evolution of the Nankai Trough seismogenic zone.  相似文献   

7.
Kaoru  Sugihara  Naoto  Masunaga  Kazuhiko  Fujita 《Island Arc》2006,15(4):437-454
Abstract The taxonomic diversity of hermatypic corals decreases with increasing latitude, which correlates with sea‐surface temperatures. However, little is known about latitudinal changes in the taxonomic diversity and biogeographic patterns of larger benthic foraminifera, although their physiological requirements are similar to those of hermatypic corals because of their symbiotic relationships with microalgae. The present study examined how the abundance and taxonomic composition of larger foraminiferal assemblages in shallow‐water reef sediments change with latitude along the Ryukyu Islands (Ryukyus), which are located near the northern limit of coral‐reef distributions in the western Pacific Ocean. Three islands from different latitudes in the Ryukyus were selected to investigate latitudinal changes in larger foraminiferal assemblages: Ishigaki Island (24°20′N, 124°10′E), Kudaka Island (26°09′N, 127°54′E) and Tane‐ga‐shima Island (30°20′N, 131°E). Four sediment samples were taken at each of three topographic sites (beach, shallow lagoon and reef crest) on the reef flat of each island. Foraminiferal tests of a 2.0‐ to 0.5‐mm size fraction were selected, identified and counted. The variations in foraminiferal abundance in reef sediments from three latitudinally different islands exhibit two contrasting trends along reef flats: a shoreward decrease on Ishigaki and Tane‐ga‐shima Islands and a shoreward increase on Kudaka Island. A total of 25, 24 and 13 foraminiferal taxa were identified in Ishigaki, Kudaka and Tane‐ga‐shima Islands, respectively. Baculogypsina sphaerulata, Neorotalia calcar and Amphistegina spp. were dominant (i.e. >3% of foraminiferal assemblages) in the three islands. Calcarina gaudichaudii and Calcarina hispida were common on Ishigaki and Kudaka Islands but were absent on Tane‐ga‐shima Island. Larger foraminiferal assemblages from three different reef‐flat environments on Ishigaki Island can be distinguished, whereas those from the three environments on Kudaka and Tane‐ga‐shima Islands are similar in composition. These latitudinal changes in larger foraminiferal assemblages in reef sediments may possibly be caused by variations in the topography of reef flats, distributions and standing crops of living foraminifers on reef flats, and the northern limit of some calcarinid species in the northern Ryukyus.  相似文献   

8.
利用FLAC3D软件模拟地震作用下不同岩层倾角的顺倾向边坡,对比坡面峰值加速度放大系数、峰值位移、地震作用结束后坡体剪应变增量的变化规律,探讨岩层倾角对顺倾边坡地震效应的影响。研究表明:(1)在水平地震波作用下,坡面水平峰值加速度放大作用随岩层倾角增大而线性减小;(2)当岩层倾角小于软弱岩层内摩擦角时,坡面峰值位移较小且变化规律受岩层倾角影响不明显,当岩层倾角大于软弱岩层内摩擦角且小于30°时坡面峰值位移增大,大于60°时减小;(3)岩层倾角小于坡角时,残余剪应变增量最大值集中在坡面中下部软弱岩层处,反之,剪应变增量最大值出现在整个坡面并呈弧形区。  相似文献   

9.
Eruptions in shallow water typically produce cones of volcaniclastic material. In order to identify any systematic effects of water depth and other environmental parameters on cone morphology, we have measured the heights and widths of cones in multibeam echo-sounder data from a submarine ridge extending southeast from Pico Island, Azores. XRF analyses of dredged samples show that lavas here vary compositionally from alkali basalt to trachybasalt and trachyandesite. Cones in deeper water are generally steep-sided with upper flanks close to 30°, the dip of talus at the angle of repose. However, height/width ratios of cones vary more in shallow water (200?C400-m summit depth) with extreme values below 0.1; while some shallow-water cones are steep-sided as in deep water, others are much flatter. Three such cones lie on a bench at 300-m depth immediately east of Pico Island and have flank slopes of only 10?C20°. We speculate that exceptionally shallow cone slopes here were produced by forced spreading of the erupting columns on reaching the water?Cair density barrier.  相似文献   

10.
本文利用福建省地震台网、广东省地震台网和台湾"中央"气象局17个台的宽频带记录,使用CAP方法反演了2018年11月26日台湾海峡M_S6.2地震震源机制解,得到节面1走向/倾角/滑动角为89°/82°/-173°,节面2走向/倾角/滑动角为358°/84°/-7°,最佳拟合深度14km,矩震级5.8.使用双差定位获取了94个M_L2.0以上地震的精定位结果,结果显示,主震位于北纬23.36°,东经118.62°,震源深度10.43km.根据小震分布和构造应力场反演得到余震断层面走向和倾角分别为88°和60°.研究认为,台湾海峡6.2级地震发震构造为近EW向的台湾浅滩断裂,受南海板块张裂拉伸发育而成,孕震过程中有东山隆起东缘断裂的参与,推测在菲律宾板块对欧亚板块NW-SE向挤压碰撞背景下,近EW向的台湾浅滩断裂与近NS向的东山隆起东缘断裂交接部位属于强度薄弱区,最终产生高倾角右旋走滑错动而引发地震,余震主要沿台湾浅滩断裂分布.  相似文献   

11.
Luminescence dating has long been used for chronological constraints on marine sediments due to the ubiquitous dating materials (quartz and feldspar grains) and its applicability over a relatively long time range. However, one of the main difficulties in luminescence dating on marine sediments is partial bleaching, which causes age overestimations. Especially, partial bleaching is typically difficult to be detected in the fine grain fraction (FG) of marine sediments. The recently developed feldspar post-IR IRSL (pIRIR) protocol can detect non-fading signals and thus avoid feldspar signal instability. In the current study, fine grains were extracted from a gravity core in the northern Sea of Japan, and the aim is to test the feasibility of using different luminescence signals with various bleaching rates to explore the bleaching conditions of fine grain fraction in marine sediments. The results suggest that the quartz OSL signal and polymineral pIRIR signals at stimulation temperatures of 150 °C and 225 °C (pIRIR150 and pIRIR225) of FG were well bleached prior to deposition. The OSL ages were used to establish a chronology for this sedimentary core and the resulting age-depth relationship is self-consistent and comparable with radiocarbon dates. We conclude that different luminescence signals with various bleaching rates can be used to test the bleaching conditions of fine grain fraction in marine sediments; and the luminescence dating can be applied to marine sediments with great potential.  相似文献   

12.
宋超  盖增喜 《地球物理学报》2018,61(4):1225-1237
据中国地震台网测定,北京时间2015年4月15日15时39分,在内蒙古自治区阿拉善左旗（39.8°N,106.3°E）发生MS5.8地震,震源深度为10 km.地震发生后多家机构对其开展了研究,本文使用喜马拉雅Ⅱ期布设在南北地震带北段的台站观测数据,通过走时反演和波形拟合反演的迭代,获得了该地区地壳一维速度结构,接着利用直达P波观测与理论走时差对震中位置重定位,然后反演地震的最佳双力偶解以及震源深度,最终得到了区域速度结构、地震的三维坐标、发震时刻以及震源机制解.结果显示,此次地震发生于世界时2015年4月15日7时39分26.718s,震中（39.7663°N,106.4304°E）,震源矩心深度18 km,矩震级MW5.25,节面Ⅰ走向176°,倾角85°,滑动角-180°,节面Ⅱ走向86°,倾角90°,滑动角-5°.结合该区域断裂带构造运动分析,本文认为此次地震是左旋走滑破裂,略带正断分量,断层面是节面Ⅱ,走向为NEE（近E-W）向,发震构造为震中附近的E-W向隐伏断裂.  相似文献   

13.
Age determination of paleotsunami sediment from Lombok Island, Indonesia, and surrounding area has been carried out using the 210 Pb method in BATAN Jakarta. The basic theory of this method assumes that weathering of sediments, including paleotsunami sediments, will result in 210 Pb enrichment. The principle of this method is to calculate 210 Pb contents accumulation in a particular sedimentation interval from the surface to the deeper buried sediments. The results are then converted into age or depositional time in years ago unit. The dating results from the paleotsunami sediments of the Gawah Pudak(S8°46’2.91’’, E115°56’34.23’’) and Gili Trawangan areas(S8°21’1.38’’, E116°2’36.6’’) indicate the Gawah Pudak sediments were deposited 37 years ago(c. in 1977)and 22 years ago(c. in 1992). Three paleotsunami sediments from Gili Trawangan were deposited 149 years ago(c. in 1865), 117 years ago(c. in 1897) and 42 years ago(c. in 1972). These results are then compared to the available Indonesian earthquake catalogue data. This study reveals that paleotsunami sediments around Lombok Islands, from older to younger, were caused by the 1857 earthquake(epicentre in Bali Sea; M7; S8°00’09.45’’,E115°29’56.41’’), 1897 earthquake(epicentre in Flores Sea;M5.5; S6°47’59.62’’, E120°48’03.5’’ or Sulu Sea earthquake; M8.5; 70 km NW of Basilan Island), the 1975 earthquake(Nusa Tenggara; S10°6’16.61’’, E123°48’09.39’’), 1977 earthquake(in Waingapu, Sumba; M8.0;S11°5’39.34’’, E118°27’50.86’’) and the 1992 earthquake(Flores; M7.8; S8°28’52.11’’, E121°53’44.3’’).  相似文献   

14.
辽南大和尚山区及其邻区存在一个盖层滑移带,它在盖层中引起了一系列逆掩叠瓦状冲断层,并伴生有花岗质岩脉注入,为今后深入研究本地区构造提供了有利条件  相似文献   

15.
  相似文献   

16.
At GMT time 13:19, August 8, 2017, an Ms7.0 earthquake struck the Jiuzhaigou region in Sichuan Province, China, causing severe damages and casualties. To investigate the source properties, seismogenic structures, and seismic hazards, we systematically analyzed the tectonic environment, crustal velocity structure in the source region, source parameters and rupture process, Coulomb failure stress changes, and 3-D features of the rupture plane of the Jiuzhaigou earthquake. Our results indicate the following: (1) The Jiuzhaigou earthquake occurred on an unmarked fault belonging to the transition zone of the east Kunlun fault system and is located northwest of the Huya fault. (2) Both the mainshock and aftershock rupture zones are located in a region where crustal seismic velocity changes dramatically. Southeast to the source region, shear wave velocity at the middle to lower crust is significantly low, but it rapidly increases northeastward and lies close to the background velocity across the rupture fault. (3) The aftershock zone is narrow and distributes along the northwest-southeast trend, and most aftershocks occur within a depth range of 5–20 km. (4) The focal mechanism of the Jiuzhaigou earthquake indicates a left-lateral strike-slip fault, with strike, dip, and rake angles of 152°, 74° and 8°, respectively. The hypocenter depth measures 20 km, whereas the centroid depth is about 6 km. The co-seismic rupture mainly concentrates at depths of 3–13 km, with a moment magnitude (Mw) of 6.5. (5) The co-seismic rupture also strengthens the Coulomb failure stress at the two ends of the rupture fault and the east segment of the Tazang fault. Aftershocks relocation results together with geological surveys indicate that the causative fault is a near vertical fault with notable spatial variations: dip angle varies within 66°–89° from northwest to southeast and the average dip angle measures ~84°. The results of this work are of fundamental importance for further studies on the source characteristics, tectonic environment, and seismic hazard evaluation of the Jiuzhaigou earthquake.  相似文献   

17.
为查明夏垫断裂东北段的空间位置、性质及其活动性,由大厂八百户起向东北方向,经过三河齐心庄至北京马坊镇,以可控震源激发方式,完成高分辨率浅层地震勘探测线7条,长约22 km.各地震反射时间剖面波组特征变化明显,断裂特征清晰,获取了准确的断点定位及断裂发育特征,展现了自八百户经齐心庄至马坊镇延伸约20 km范围内夏垫断裂的...  相似文献   

18.
云南耿马7.2级地震地表破裂带研究   总被引：2，自引：1，他引：2       下载免费PDF全文
根据野外考察的实际资料,本文介绍了耿马7.2级地震地表破裂带的展布,结构要素及组合、位移分布等情况。同时依据位错资料对破裂带的应力活动及断裂两盘的运动状态进行了初步分析。认为本次地震发震构造以右旋走滑为主兼具张性,主压应力优势方位为N5°—10°E。断层两盘相对运动的总体方向为N55°W左右,断层运动的滑移角在30°—40°之间  相似文献   

19.
This paper describes delta development processes with particular reference to Cimanuk Delta in Indonesia. Cimanuk river delta, the most rapidly growing river delta in Indonesia, is located on the northern coast of Java Island. The delta is subject to ocean waves of less than 1 m height due to its position in the semi‐enclosed Java Sea in the Indonesian archipelago. The study has been carried out using a hydrodynamic model that accounts for sediment movement through the rivers and estuaries. As an advanced approach to management of river deltas, a numerical model, namely MIKE‐21, is used as a tool in the management of Cimanuk river delta. From calibration and verification of hydrodynamic model, it was found that the best value of bed roughness was 0·1 m. For the sediment‐transport model, the calibration parameters were adjusted to obtain the most satisfactory results of suspended sediment concentration and volume of deposition. By comparing the computed and observed data in the calibration, the best values of critical bed shear stress for deposition, critical bed shear stress for erosion and erosion coefficient were 0·05 N m?2, 0·15 N m?2, and 0·00001 kg m?2 s?1, respectively. The calibrated model was then used to analyse sensitivity of model parameters and to simulate delta development during the periods 1945–1963 and 1981–1997. It was found that the sensitive model parameters were bed shear stresses for deposition and erosion, while the important model inputs were river suspended sediment concentration, sediment characteristics and hydrodynamic. The model result showed reasonable agreement with the observed data. As evidenced by field data, the mathematical model proves that the Cimanuk river delta is a river‐dominated delta because of its protrusion pattern and very high sediment loads from the Cimanuk river. It was concluded that 86% of sediment load from the Cimanuk river was deposited in the Cimanuk delta. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

20.
In organic-enriched sedimentary systems, like many Mediterranean coastal lagoons, a detailed analysis of sediment grain size composition and partitioning within the muds is crucial to investigate sedimentological trends related to both hydrodynamic energy and basin morphology. In these systems, sediment dynamics are particularly important because the partitioning and transport of fine sediments can strongly influence the redistribution and accumulation of large amounts of organic matter, and consequently the distribution of benthic assemblages and the trophic status and functioning of a lagoon. Nevertheless, studies on benthic-sediment relationships have been based mainly on a rather coarse analysis of sediment grain size features. In muddy systems, however, this approach may impede a proper evaluation of the relationships and effects of the distribution of fine sediment and organic matter on the biotic benthic components. Here we show that the distribution of sedimentary organic matter (OM) and total organic carbon (TOC) in the Cabras lagoon (Sardinia, Italy) can be explained (i.e., predicted) as a function of a nonlinear increase in the amount of the cohesive fraction of sediments (< or = 8 microm grain size particles) and that this fraction strongly influences the structure, composition and distribution of macrobenthic assemblages. Even in such a homogeneously muddy system, characterized by "naturally" occurring impoverished communities, impaired benthic assemblages were found at < or = 8 microm, OM, TOC contents of about 77%, 11% and 3.5%, respectively. A review of studies conducted in Mediterranean coastal lagoons highlighted a lack of direct integrated analysis of sediment features and the biotic components. We suggest that, especially in organic-enriched coastal lagoons, monitoring programs should primarily investigate and consider the cohesive fraction of sediments in order to allow a better assessment of benthic-sediment relationships and ecological quality of the system.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号