首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
The procedures used to construct monitoring wells with hollow-stem augers may vary depending on the hydrogeologic conditions at the site. In cohesive materials in which the borehole stands open, the auger column may be fully retracted from the borehole prior to the construction of the monitoring well. In non-cohesive materials in which the borehole will not stand open, the monitoring well may be constructed through the hollow axis of the auger column.
The techniques used to construct monitoring wells through the hollow axis of the auger column may vary depending on the specific site conditions and the experience of the driller. Selection of an appropriately sized diameter hollow-stem auger for the installation of the required size of well casing is necessary to permit an adequate working space between the casing and augers, through which filter pack and annular seal materials are emplaced. Assurance that the filter pack and annular seal are properly emplaced is typically limited to careful measurements taken and recorded during construction of the monitoring well.  相似文献   

2.
A New System for Ground Water Monitoring   总被引：4，自引：0，他引：4  
This paper describes a new system for ground water monitoring, "the BAT System," which includes the following functions: (a) sampling of ground water in most types of soils, (b) measurement of pore water pressure, and (c) in situ measurement of hydraulic conductivity. The system can also be used for tracer tests. The system utilizes a permanently installed filter tip attached to a steel or PVC pipe. Installation is normally performed by pushing the tip down to the desired depth. The filter tip can also be buried beneath a landfill. The primary feature of the new system is that the filter tip contains a self-sealing quick coupling unit, which makes it possible to temporarily connect the filter tip to adapters for various functions, e.g. water sampling and for measurement of pore pressure and hydraulic conductivity. The new technique makes sampling of both pressurized water and gas possible. Samples are obtained directly in hermetically sealed, pre-sterilized sample cylinders. Sampling of ground water and measurement of pore pressure can be repeated over a long period of time with undiminished accuracy. This technique is also well-adapted for taking water samples from different strata in a soil profile, in both the saturated and unsaturated zones. Actual installations range from 0.5 to 60m depth.  相似文献   

3.
A large weighing lysimeter was installed at Yucheng Comprehensive Experimental Station, north China, for evapotranspiration and soil‐water–groundwater exchange studies. Features of the lysimeter include the following: (i) mass resolution equivalent to 0·016 mm of water to accurately and simultaneously determine hourly evapotranspiration, surface evaporation and groundwater recharge; (ii) a surface area of 3·14 m2 and a soil profile depth of 5·0 m to permit normal plant development, soil‐water extraction, soil‐water–groundwater exchanges, and fluctuations of groundwater level; (iii) a special supply–drainage system to simulate field conditions of groundwater within the lysimeter; (iv) a soil mass of about 30 Mg, including both unsaturated and saturated loam. The soil consists mainly of mealy sand and light loam. Monitoring the vegetated lysimeter during the growing period of winter wheat, from October 1998 through to June 1999, indicated that during the period groundwater evaporation contributed 16·6% of total evapotranspiration for a water‐table depth from 1·6 m to 2·4 m below ground surface. Too much irrigation reduced the amount of upward water flow from the groundwater table, and caused deep percolation to the groundwater. Data from neutron probe and tensiometers suggest that soil‐water‐content profiles and soil‐water‐potential profiles were strongly affected by shallow groundwater. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

4.
Continuous remediation monitoring using sensors is potentially a more effective and inexpensive alternative to current methods of sample collection and analysis. Gaseous components of a system are the most mobile and easiest to monitor. Continuous monitoring of soil gases such as oxygen, carbon dioxide, and contaminant vapors can provide important quantitative information regarding the progress of bioremediation efforts and the area of influence of air sparging or soil venting. Laboratory and field tests of a commercially available oxygen sensor show that the subsurface oxygen sensor provides rapid and accurate data on vapor phase oxygen concentrations. The sensor is well suited for monitoring gas flow and oxygen consumption in the vadose zone during air sparging and bioventing. The sensor performs well in permeable, unsaturated soil environments and recovers completely after being submerged during temporary saturated conditions. Calibrations of the in situ oxygen sensors were found to be stable after one year of continuous subsurface operation. However, application of the sensor in saturated soil conditions is limited. The three major advantages of this sensor for in situ monitoring arc as follows: (1) it allows data acquisition at any specified time interval; (2) it provides potentially more accurate data by minimizing disturbance of subsurface conditions; and (3) it minimizes the cost of field and laboratory procedures involved in sample retrieval and analysis.  相似文献   

5.
Sampling of soil pore moisture in the vadose zone underneath land disposal facilities (landfills and surface impoundments) for hazardous waste has been suggested as an "early warning system" to detect leakage from these facilities. Some states require vadose zone moisture sampling at such sites. Given a leak of a particular size, mathematical models can estimate the necessary moisture sample volume collection times and lysimeter spacings to guarantee detection of the leak in a homogeneous medium. Examination of 47 hazardous waste sites existing in 1984 indicated the most were located in areas with water tables too shallow to permit vadose zone detection monitoring. Several of the 47 sites had soils that could be described as loamy sand, silt loam or silty clay. Using these three soils as examples, the process of lysimeter leak-detector network design has been illustrated. For a particular loamy sand with a saturates hydraulic conductivity of 10-6 cm/ sec, the maximum ceramic lysimeter spacing is 15.5 feet at a depth of 30 feet to collec a moisture sample of 10 mL in one week from a 1 ft2 leak. For a silt loam, maximum lysimeter spacing would be 17 feet at depth of 15 feet. For silty clays, the maximum lysimeter spacing is 7 feet at a depth of 2 feet; maximum emplacement depth is about 9 feet. Calculations show that in some soils, suction lysimeters will not be able to collect usable moisture samples. Since soil properties vary widely and lysimeter spacing is strongly dependent on soil-moisture characteristics appropriate soil measurements and modeling must be performed at each disposal facility to estimate lysimete performance and to select locations for emplacement.  相似文献   

6.
The union of a piezoresistive pressure transducer and a porous ceramic cup was termed "transiometer." The transiometer was constructed from economical and readily available materials. It could be used to measure soil water potentials in both saturated and unsaturated conditions, and was well suited to continuous monitoring with data acquisition equipment.
Transiometer testing was conducted at two sites, one of moderate permeability and the other of slow permeability. The slowly permeable site was instrumented with four replications of the following: (1) transiometers installed at four depths, (2) a transi-ometerwithout the ceramic cup, (3) apiezometer, and (4) access tubes for monitoring soil moisture with a neutron probe. The moderately permeable site was instrumented with a transiometer, two piezometers, and an access tube for monitoring with a neutron probe.
In saturated conditions the transiometer had a faster response time after installation than the piezometer. Faster response makes the transiometer more desirable for use in slowly permeable soils, especially when monitoring dynamic soil water.
Calculated random error of the transiometer measuring system, including a digital voltmeter and a scanner, was typically 0.09 feet (2.8cm), with a maximum calculated to be 0.38 feet (11.5cm). The two most significant components were imprecision of the scanner card and calibration shift. The transiometer was sensitive to atmospheric pressure fluctuations, with sensitivity to atmospheric pressure change increasing with installation depth.  相似文献   

7.
Shah N  Nachabe M  Ross M 《Ground water》2007,45(3):329-338
In many landscapes, vegetation extracts water from both the unsaturated and the saturated zones. The partitioning of evapotranspiration (ET) into vadose zone evapotranspiration and ground water evapotranspiration (GWET) is complex because it depends on land cover and subsurface characteristics. Traditionally, the GWET fraction is assumed to decay with increasing depth to the water table (DTWT), attaining a value of 0 at what is termed the extinction depth. A simple assumption of linear decay with depth is often used but has never been rigorously examined using unsaturated-saturated flow simulations. Furthermore, it is not well understood how to relate extinction depths to characteristics of land cover and soil texture. In this work, variable saturation flow theory is used to simulate GWET for three land covers and a range of soil properties under drying soil conditions. For a water table within half a meter of the land surface, nearly all ET is extracted from ground water due to the close hydraulic connection between the unsaturated and the saturated zones. For deep-rooted vegetation, the decoupling of ground water and vadose zone was found to begin at water table depths between 30 and 100 cm, depending on the soil texture. The decline of ET with DTWT is better simulated by an exponential decay function than the commonly used linear decay. A comparison with field data is consistent with the findings of this study. Tables are provided to vary the extinction depth for heterogeneous landscapes with different vegetation cover and soil properties.  相似文献   

8.
Hollow-stem augers are a widely used drilling method for constructing monitoring wells in unconsolidated materials. The drilling procedures used when constructing monitoring wells with hollow-stem augers, however, are neither standardized nor thoroughly documented in the published literature.
Variations in drilling procedures and techniques may occur as a result of the: (1) type of auger drill equipment and formation samplers used; (2) hydrogeologic conditions at the site, especially where heaving sands occur; and (3) known or suspected presence of contaminated zones, where there is a potential for the vertical movement of contaminants within the borehole.
In a saturated zone in which heaving sands occur, changes in equipment and drilling techniques are required to provide a positive pressure head of water within the auger column. This may require the addition of clean water or other drilling fluid inside the augers.
When monitoring the quality of ground water below a known contaminated zone, hollow-stem auger drilling may not be advisable unless protective surface casing can be installed. Depending on the site hydrogeology, conventional hollow-stem auger drilling techniques alone may not be adequate for the installation of the protective surface casing. A hybrid drilling method may be needed that combines conventional hollow-stem auger drilling with a casing driving technique that advances the borehole and surface casing simultaneously.  相似文献   

9.
The strong vertical gradient in soil and subsoil saturated hydraulic conductivity is characteristic feature of the hydrology of catchments. Despite the potential importance of these strong gradients, they have proven difficult to model using robust physically based schemes. This has hampered the testing of hypotheses about the implications of such vertical gradients for subsurface flow paths, residence times and transit time distribution. Here we present a general semi‐analytical solution for the simulation of 2D steady‐state saturated‐unsaturated flow in hillslopes with saturated hydraulic conductivity that declines exponentially with depth. The grid‐free solution satisfies mass balance exactly over the entire saturated and unsaturated zones. The new method provides continuous solutions for head, flow and velocity in both saturated and unsaturated zones without any interpolation process as is common in discrete numerical schemes. This solution efficiently generates flow pathlines and transit time distributions in hillslopes with the assumption of depth‐varying saturated hydraulic conductivity. The model outputs reveal the pronounced effect that changing the strength of the exponential decline in saturated hydraulic conductivity has on the flow pathlines, residence time and transit time distribution. This new steady‐state model may be useful to others for posing hypotheses about how different depth functions for hydraulic conductivity influence catchment hydrological response. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

10.
Lighter-than-water Non-Aqueous Phase Liquids (LNAPLs), such as jet fuels or gasolines, are common contaminants of soils and ground water. However, the total volume and distribution of an LNAPL is difficult to accurately determine during a site investigation. LNAPL that is entrapped in the saturated zone due to fluctuating water table conditions is particularly difficult to quantify. Yet, the amount of entrapped product in the saturated zone is theoretically higher, per volume of soil, than the residual product in the unsaturated zone, and small amounts of LNAPL in the saturated zone can contaminate large volumes of ground water.
The only method currently available to quantify the amount of LNAPL is direct soil-core sampling combined with laboratory analysis of the fluid extracted from the soil cores. However, direct sampling of saturated ground water systems with conventional samplers presents a number of problems. In this study, a new sampler was developed that can be used to retrieve undisturbed soil and pore fluid samples from below the water table in cohesionless soils. The sampler uses carbon dioxide to cool the bottom of a saturated soil sample in situ to near freezing. Results of a field study where a prototype sampler was tested demonstrate the usefulness of a cryogenic sampler and show that the amount of LNAPL entrapped below the water table can be a significant part of the total LNAPL in the soil.  相似文献   

11.
  相似文献   

12.
Evaluation for metal and radionuclide contamination associated with selected inactive uranium mill tailings repositories required the installation of monitoring wells in both shallow unconfined and deep artesian aquifer systems. To prevent ionic exchange between the dissolved cationic metals and the cations in bentonitic drilling fluids, organic-based fluids were used during the drilling and installation of monitoring wells. Experience gained at three western U.S. sites involving inactive uranium mill tailings indicates organic drilling fluids can be used to advance drill holes in soil materials ranging from saturated silts and fine sands to unsaturated gravels. However, it has been determined that certain types of these organic fluids can clog very narrow screen slots and remain present in well discharge, even after several hours of well cleaning. Certain types of organic drilling fluids appear to be preferable for these types of water chemistry studies.  相似文献   

13.
A small but significant proportion of all existing monitoring wells may be affected by leakage through the casing, usually at joints. Casing leakage can render data obtained from a monitoring well unreliable. Anomalous water level, water quality, or isotope data from a particular well are an indication of possible leakage. The occurrence of a casing leak can be confirmed by means of a pressure test using water. The magnitude of the leakage flow can be estimated from the pressure test or from the observed head anomaly. Casing leaks can be largely prevented with adequate care during monitoring well installation, but the possibility that data may be affected by casing leaks should always be taken into account during hydrogeological investigations.  相似文献   

14.
Abstract. MRCON is an interactive computer program designed to approximate soil moisture retention ( Θ-Ψ ) and/or unsaturated hydraulic conductivity (K- Θ ) for soils. MRCON, which is written in BASIC, uses empirical methods obtained from the literature to calculate K- Θ and a modified method to calculate Θ-Ψ . Input data for the program consist of a saturated moisture content and a minimum of three values of Θ-Ψ . A measured value of saturated hydraulic conductivity can be used as input to better approximate the K -Θ curves to field conditions.  相似文献   

15.
Abstract
A modular multilevel sampler was developed and utilized for sampling undisturbed ground water chemical profiles and gases in both the saturated and the unsaturated zone. Sampling at 3cm depth intervals is based on the dialysis-cell method and has no depth limitations. The sampler may be used for the development of early warning monitoring systems and research.  相似文献   

16.
Hydraulic properties of saturated and unsaturated stony soils were studied on a 3.35 m long column, 1.24 m in diameter, filled with alternating sand and boulder layers. The boulders averaged 6.2 × 15 × 20 cm in size and were laid down on their flat side. Tensiometers and a neutron probe access tube were placed in the column for measuring pressure heads and water contents, respectively. Saturated conditions were obtained by ponding the column. The resulting hydraulic conductivity K was 5.1 m/day. This value could also be calculated from the measured K for the sand alone on separate samples, using a simple equation that takes into account the void ratio of the sand alone and that of the boulder-sand mixture. Unsaturated K was determined by applying water at less than ponded infiltration rates. Resulting relations between the unsaturated K and water content or negative pressure head could also be estimated from the relation between unsaturated K and pressure head for the sand alone and the calculated saturated K of the boulder-sand mixture. The method of Millington and Quirk for calculating the relation between unsaturated K and water content also gave reasonable results. The dispersivity of the boulder-sand column was 18 times that of the sand alone. Pore velocity was accurately estimated as the Darcy velocity divided by the volumetric water content. Hydraulic properties of stony vadose zones are difficult to determine. This work shows that they can be estimated from K relations measured in the laboratory on samples of the soil between the rocks. Knowledge of hydraulic properties of vadose zones is important in predicting movement of water and pollutants to the underlying ground water.  相似文献   

17.
Waste disposal sites with volatile organic compounds (VOCs) frequently contain contaminants that are present in both the ground water and vadose zone. Vertical sampling is useful where transport of VOCs in the vadose zone may effect ground water and where steep vertical gradients in chemical concentrations are anticipated. Designs for combination ground water and gas sampling wells place the tubing inside the casing with the sample port penetrating the casing for sampling. This physically interferes with pump or sampler placement. This paper describes a well design that combines a ground water well with gas sampling ports by attaching the gas sampling tubing and ports to the exterior of the casing. Placement of the tubing on the exterior of the casing allows exact definition of gas port depth, reduces physical interference between the various monitoring equipment, and allows simultaneous remediation and monitoring in a single well. The usefulness and versatility of this design was demonstrated at the Idaho National Engineering and Environmental Laboratory (INEEL) with the installation of seven wells with 53 gas ports, in a geologic formation consisting of deep basalt with sedimentary interbeds at depths from 7.2 to 178 m below land surface. The INEEL combination well design is easy to construct, install, and operate.  相似文献   

18.
A one‐dimensional, two‐layer solute transport model is developed to simulate chemical transport process in an initially unsaturated soil with ponding water on the soil surface before surface runoff starts. The developed mathematical model is tested against a laboratory experiment. The infiltration and diffusion processes are mathematically lumped together and described by incomplete mixing parameters. Based on mass conservation and water balance equations, the model is developed to describe solute transport in a two‐zone layer, a ponding runoff zone and a soil mixing zone. The two‐zone layer is treated as one system to avoid describing the complicated chemical transport processes near the soil surface in the mixing zone. The proposed model was analytically solved, and the solutions agreed well with the experimental data. The developed experimental method and mathematical model were used to study the effect of the soil initial moisture saturation on chemical concentration in surface runoff. The study results indicated that, when the soil was initially saturated, chemical concentration in surface runoff was significantly (two orders of magnitude) higher than that with initially unsaturated soil, while the initial chemical concentrations at the two cases were of the same magnitude. The soil mixing depth for the initially unsaturated soil was much larger than that for the initially saturated soil, and the incomplete runoff mixing parameter was larger for the initially unsaturated soil. The higher the infiltration rate of the soil, the greater the infiltration‐related incomplete mixing parameter. According to the quantitative analysis, the soil mixing depth was found to be sensitive for both initially unsaturated and saturated soils, and the incomplete runoff mixing parameter was sensitive for initially saturated soil but not for the initially unsaturated soil; the incomplete infiltration mixing parameter behaved just the opposite. Some suggestions are made for reducing chemical loss from runoff. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

19.
Here we use Richards Equation models of variably saturated soil and bedrock groundwater flow to investigate first-order patterns of the coupling between soil and bedrock flow systems. We utilize a Monte Carlo sensitivity analysis to identify important hillslope parameters controlling bedrock recharge and then model the transient response of bedrock and soil flow to seasonal precipitation. Our results suggest that hillslopes can be divided into three conceptual zones of groundwater interaction, (a) the zone of lateral unsaturated soil moisture accumulation (upper portion of hillslope), (b) the zone of soil saturation and bedrock recharge (middle of hillslope) and (c) the zone of saturated-soil lateral flow and bedrock groundwater exfiltration (bottom of hillslope). Zones of groundwater interaction expand upslope during periods of precipitation and drain downslope during dry periods. The amount of water partitioned to the bedrock groundwater system a can be predicted by the ratio of bedrock to soil saturated hydraulic conductivity across a variety of hillslope configurations. Our modelled processes are qualitatively consistent with observations of shallow subsurface saturation and groundwater fluctuation on hillslopes studied in our two experimental watersheds and support a conceptual model of tightly coupled shallow and deep subsurface circulation where groundwater recharge and discharge continuously stores and releases water from longer residence time storage.  相似文献   

20.
Tile‐drain response to rainfall events is determined by unsaturated vertical flow to the water table, followed by horizontal saturated water movement. In this study, unsaturated vertical movement from the redistribution of water is modelled using a sharp‐front approximation, and the saturated horizontal flow is modelled by an approximate solution to the Boussinesq equation. The unsaturated flow component models the fast response that is associated with the presence of preferential flow paths. By convoluting the responses of the two components, a transfer function is developed that predicts tile‐drain response to unit amounts of infiltrated water. It is observed that the unsaturated flow component can be cast in a form that is linear in a power function of the infiltrated depth. Since the approach is process based, model parameter definitions are easily identified with soil properties at the field scale. Furthermore, it is demonstrated that the transfer function model parameters can be estimated from moment analysis. Using superposition, the transient tile‐drain response to arbitrary amounts of infiltrated water can be constructed. Comparison with data measured from the Water Quality Field Station show that this approach provides a promising method for generating tile‐drain response to rainfall events. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号