共查询到19条相似文献，搜索用时 453 毫秒
1.
三维溶质运移问题的分步广义迎风解法 总被引：1，自引：0，他引：1
姚磊华 《长春地质学院学报》1997,27(4):424-428
对对流占优的三维溶质运移问题提出了分步广义的迎风解法，首先利用Ｎ，Ｎ，Ｙａｎｅｎｋｏ对水动力弥散方程分步求解的思想，将原来的一个定解问题分解为两个定解问题即对流定解问题和扩散定解问题，对对流定解问题采用广义迎风对偶单元均衡法求解，对扩散定解问题采用一般的Ｇａｌｅｒｋｉｎ有限元法求解，不仅避免了用一般有限元法和有限差分法求解对流占优的地下水水质数学模型时常出现数值弥散和过量问题，而且避免了求节眯速度 相似文献
2.
根据水质模型的具体特点，对不同的方程采用不同方法，水流问题用有限元法；对流弥散方程先用算子分裂的方法分解为两个方程，即对流方程和弥散方程，前者用高精度广义迎风格式求解，对弥散方程则采用多单元均衡格式法求解，最后合成为高精度广义迎风均衡格式求出溶质浓度。通过对数值实验例子的计算和实验溶质迁移的模拟，可以看出在求解对流弥散定解问题时，广义迎风均衡格式克服了有限元数值波动和浓度出现负值的问题，与有限元相比有较大改进。 相似文献
3.
根据水质模型的具体特点，对不同的方程采用不同方法，水流问题用有限元法；对流弥散方程先用算子分裂的方法分解为两上方程，即对流方程和弥散方程，前者用高精度广义迎风格式求解，对弥散方程则采用多单元均衡格式法求解，最后合成为高精度广义迎风均衡格式求出溶质浓度。 相似文献
4.
采用剖开算子法,把二维输运问题剖分为两个子初值问题(对流分步、扩散分步)。在任意三角形网格中,分别对不同性质的算子采用各自适合的算法,即采用特征线法求解对流分步,采用半隐式有限元法求解扩散分步。重点探讨了对流插值问题,给出了一种完全对称三次插值模式,有效地减少了数值阻尼。为了克服高阶插值数值震荡问题,计算中保证了函数及其一阶偏导数连续。算例表明,数值方法模拟结果与精确解吻合较好。该算法在求解输运方程(包括纯对流输运方程)时,既能有效减少数值阻尼,也能保证计算中不出现数值震荡。 相似文献
5.
6.
在求解非稳定地下水溶质运移模型时,若对流项占优,则模型表现出双曲方程的特性。针对这种特性,采用非标准Galerkin有限元方法进行求解是解决这类问题的有效途径。分别采用Wavelet-Galer-kin有限元方法、迎风有限元方法和特征有限元方法对强对流溶质运移模型进行了求解,并将其结果与标准Galerkin有限元和解析解进行对比。结果表明:标准Galerkin有限元方法会产生强烈的数值振荡;Wavelet-Galerkin有限元方法的时空定位效果好;迎风有限元方法能够有效降低数值振荡现象,但迎风因子对解的影响较大,而且会带来时间延迟;特征有限元方法能够提高解的精度,故可以认为特征有限元方法是求解强对流地下水溶质运移模型的首选方法。 相似文献
7.
利用算子分裂迎风均衡格式解对流为主溶质运移问题 总被引：2，自引：0，他引：2
水污染模拟问题是水流问题与溶质运移问题的耦合问题.各种常见的数值解法在以对流为主溶质运移问题的求解中都会遇到困难,如用有限单元法或有限差分法时,会产生数值弥散与过量这两类误差.引入算子分裂迎风均衡格式法求解对流为主的水污染模拟问题,较好地克服了数值弥散和数值解出现振荡问题,该格式具有良好的稳定性、单调性及守恒性特点. 相似文献
8.
9.
描述非饱和土壤中溶质运移的对流弥散方程可分成两部分，对流部分用通量校正运移（FCT）算法求解；弥散部分用常规的隐式差分方法求解，FCT算法包括两个阶段，一个是低阶运移阶段，这一阶段的解，可能会引进过量的数值弥散，另一个是高阶通量校正阶段，通过对反扩散通量进行校正（限定），可有效地消除数值弥散和数值振荡，而水体积分数用FUCG方法求得，能保持质量守恒，通过数值例子验证了FCT算法的有效性。 相似文献
10.
有限元法是求解地下水流和溶质运移对流-弥散方程的常用数值方法,它可以精确高效地处理以弥散为主的问题,但求解以对流为主的问题易引起显著的数值振荡。通过Galerkin有限元法对变异Henry问题进行模拟求解,得到了用不同的剖分网格及水动力弥散系数时,在特选节点处的浓度穿透曲线,分析并找到了浓度振荡的原因及合适的消除方法,即若出现浓度数值解在某值附近振荡,可以通过加密网格或增加水动力弥散系数将其消除。模拟结果及其分析表明:即使是研究区域相同,不同的边界条件、不同的水动力弥散系数对网格精度的要求不同;换言之,同一网格对不同模型参数的有效性也不同。网格Peclet数能够有效地判定给定的网格剖分是否会引起浓度振荡,对有限元法数值计算的网格剖分具有指导意义。 相似文献
11.
Multi-phase flow in porous media in the presence of viscous, gravitational, and capillary forces is described by advection diffusion equations with nonlinear parameters of relative permeability and capillary pressures. The conventional numerical method employs a fully implicit finite volume formulation. The phase-potential-based upwind direction is commonly used in computing the transport terms between two adjacent cells. The numerical method, however, often experiences non-convergence in a nonlinear iterative solution due to the discontinuity of transmissibilities, especially in transition between co-current and counter-current flows. Recently, Lee et al. (Adv. Wat. Res. 82, 27–38, 2015) proposed a hybrid upwinding method for the two-phase transport equation that comprises viscous and gravitational fluxes. The viscous part is a co-current flow with a one-point upwinding based on the total velocity and the buoyancy part is modeled by a counter-current flow with zero total velocity. The hybrid scheme yields C1-continuous discretization for the transport equation and improves numerical convergence in the Newton nonlinear solver. Lee and Efendiev (Adv. Wat. Res. 96, 209–224, 2016) extended the hybrid upwind method to three-phase flow in the presence of gravity. In this paper, we present the hybrid-upwind formula in a generalized form that describes two- and three-phase flows with viscous, gravity, and capillary forces. In the derivation of the hybrid scheme for capillarity, we note that there is a strong similarity in mathematical formulation between gravity and capillarity. We thus greatly utilize the previous derivation of the hybrid upwind scheme for gravitational force in deriving that for capillary force. Furthermore, we also discuss some mathematical issues related to heterogeneous capillary domains and propose a simple discretization model by adapting multi-valued capillary pressures at the end points of capillary pressure curves. We demonstrate this new model always admits a consistent solution that is within the discretization error. This new generalized hybrid scheme yields a discretization method that improves numerical stability in reservoir simulation. 相似文献
12.
In this paper, an arbitrary Lagrangian–Eulerian (ALE) method is generalized to solve consolidation problems involving large deformation. Special issues such as pore‐water pressure convection, permeability and void ratio updates due to rotation and convection, mesh refinement and equilibrium checks are discussed. A simple and effective mesh refinement scheme is presented for the ALE method. The ALE method as well as an updated‐Lagrangian method is then used to solve some classical consolidation problems involving large deformations with different constitutive laws. The results clearly show the advantage and efficiency of the ALE method for these examples. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
13.
建立了二维非恒定渗流的有限元并行计算模型,在windows操作系统下实现了基于消息传递的二维渗流的有限元并行计算。模型采用广义极小残余算法(GMRES)对方程组进行并行迭代求解,通过分析数据执行时的相关性和检验算法结构的固有串行性,将原有串行算法中的算法元直接并行化。对溪洛渡上游围堰的渗流分析进行了并行数值模拟,并针对水位骤降情况下非恒定渗流进行了并行计算,证明了模型的合理性。对模型进行了加速比测定,可以看出并行计算的效率随着问题规模的增加而逐渐提高。 相似文献
14.
岩溶区地下水数值模拟研究进展 总被引：2，自引：2，他引：0
岩溶含水介质的不均一性导致岩溶地下水流动、溶质运移和热量迁移的数学模拟研究成为地下水模拟的难点。本文综述了岩溶区地下水流模拟的几种方法,重点阐述了等效多孔介质法、双重连续介质法和三重介质法的定义、发展过程和适用范围,并回顾了这几种方法的研究成果。从等效多孔介质法到三重介质法,模拟精度不断提高,适用范围也逐渐由大区域实际问题向小区域理论研究过渡。介绍了溶质运移模拟和热迁移模拟的研究方法及实例。溶质运移模拟以对流弥散方程为基础,其中尺度效应是溶质运移模拟的重点研究问题;热量迁移模拟应考虑地下热水密度变化对地下热水运动的影响。溶质运移模拟和热量迁移模拟往往是将迁移模型和已经调试成功的地下水流动模型相耦合,从而达到模拟溶质及热量迁移的目的。由于溶质运移和热量迁移的复杂性,现阶段水流模型多数处于等效多孔介质模型阶段。综合理论及实际应用,指出精确刻画裂隙及管道和注重基础数学算法是岩溶水数值模拟进步的关键。 相似文献
15.
John Z. Shi Hong-Qiang Zhou Hua Liu Yong-Gang Zhang 《Environmental Earth Sciences》2010,61(8):1691-1702
Tidal flow and fine-sediment transport at the South Channel–North Passage of the partially-mixed Changjiang River estuary
were studied using a two-dimensional horizontal (2DH) numerical model. This 2DH model was achieved by depth-integrating the
momentum and convection–diffusion equations. The Alternating Direction Implicit scheme was used to solve the governing equations.
The iterative method was adopted for the calculation of convection and diffusion terms of momentum equation. Comparisons between
calculated and measured results (tidal elevations and depth-averaged velocities) have shown reasonable agreement. Horizontal
distributions of tidal current velocity and suspended sediment concentration were qualitatively consistent with observations.
Those modeled results were analyzed to elucidate the mechanisms for the formation of the turbidity maximum and intratidal
variations in fine-sediment transport processes. 相似文献
16.
An overview of numerical techniques and previous investigations related to the solution of advection‐dominated transport processes is presented. In addition a new Symmetrical Streamline Stabilization (S3) scheme is introduced. The basis of the technique is to treat the transport equation in two steps. In the first step the dispersion part is approximated by a standard Galerkin approach, while in the second step the advection is approximated by a least‐squares method. The two parts are reassembled, resulting in one system of equations. The resulting coefficients' matrix is symmetric. Only half of a sparse matrix needs to be stored. Robust iterative algorithms for symmetrical systems of equations such as the preconditioned conjugate gradient method (PCG) can be successfully used. The new method leads to an implicit introduction of an ‘artificial diffusion’ term. Solute transport with high Peclet and Courant numbers does not lead to oscillations due to an inherent upwind damping. The upwind effect acts only in flow direction. The efficiency of the new formulation in terms of accuracy and computation time is shown in comparison with the Galerkin approach for mesh parallel and mesh oblique high advective solute transport. Copyright © 2000 John Wiley & Sons, Ltd. 相似文献
17.
T. Kuppusamy 《国际地质力学数值与分析法杂志》1993,17(7):457-469
Aquifer contamination by organic chemicals in subsurface flow through soils due to leaking underground storage tanks filled with organic fluids is an important groundwater pollution problem. The problem involves transport of a chemical pollutant through soils via flow of three immiscible fluid phases: namely air, water and an organic fluid. In this paper, assuming the air phase is under constant atmospheric pressure, the flow field is described by two coupled equations for the water and the organic fluid flow taking interphase mass transfer into account. The transport equations for the contaminant in all the three phases are derived and assuming partition equilibrium coefficients, a single convective – dispersive mass transport equation is obtained. A finite element formulation corresponding to the coupled differential equations governing flow and mass transport in the three fluid phase porous medium system with constant air phase pressure is presented. Relevant constitutive relationships for fluid conductivities and saturations as function of fluid pressures lead to non-linear material coefficients in the formulation. A general time-integration scheme and iteration by a modified Picard method to handle the non-linear properties are used to solve the resulting finite element equations. Laboratory tests were conducted on a soil column initially saturated with water and displaced by p-cymene (a benzene-derivative hydrocarbon) under constant pressure. The same experimental procedure is simulated by the finite element programme to observe the numerical model behaviour and compare the results with those obtained in the tests. The numerical data agreed well with the observed outflow data, and thus validating the formulation. A hypothetical field case involving leakage of organic fluid in a buried underground storage tank and the subsequent transport of an organic compound (benzene) is analysed and the nature of the plume spread is discussed. 相似文献
18.
19.
This work is intended for the development of a numerical method to simulate flows and solute transport in multiphasical porous medium taking into consideration the interaction of solid/solute. More precisely, the studied problem is modeled by a coupled system composed of an elliptical equation (for the flow) and an equation convection–diffusion–reaction (for the transfer). Numerical simulations were realistic for two-dimensional problems confirming the stability and efficiency of the combined scheme in the characterization of a pollutant transport through an unsaturated zone of an industrial site. 相似文献