共查询到20条相似文献，搜索用时 15 毫秒
1.
Carl Keller 《Ground water》2017,55(2):244-254
This study describes a new technique for measuring the head profile in a geologic formation. The technique provides rapid, low cost information on the depth of water‐producing zones and aquitards in heterogeneous aquifers, yielding estimates of hydraulic heads in each zone while identifying any potential for cross contamination between zones. The measurements can be performed in a typical borehole in just a few hours. The procedure uses both the continuous transmissivity profile obtained by the installation (eversion) of a flexible borehole liner into an open borehole and the subsequent removal (inversion) of the same liner from the borehole. The method is possible because of the continuous transmissivity profile (T profile described by Keller et al. 2014) obtained by measuring the rate of liner eversion under a constant driving head. The hydraulic heads of producing zones are measured using the reverse head profile (RHP) method (patent no. 9,008,971) based on a stepwise inversion of the borehole liner. As each interval of the borehole is uncovered by inversion of the liner, the head beneath the liner is allowed to equilibrate to a steady‐state value. The individual hydraulic heads contributing to each measurement are calculated using the measured transmissivity for each zone. Application of the RHP method to a sedimentary bedrock borehole in New Jersey verified that it reproduced the head distribution obtained the same day in the same borehole instrumented with a multilevel sampling system. 相似文献
2.
Advanced borehole-geophysical methods were used to assess the geohydrology of fractured crystalline bedrock at five test boreholes in southwestern Manhattan Island, New York, in preparation for construction of a third water tunnel for New York City. The boreholes penetrated gneiss and other crystalline bedrock that has an overall southwest to northwest dipping foliation with a 60° dip. Most of the fractures encountered are either nearly horizontal or have moderate northwest dip azimuths. Fracture indexes range from 0.25 to 0.44 fracture per foot (0.3 m) of borehole.
Electromagnetic (EM) and heat-pulse flowmeter logs obtained under ambient and pumping conditions, together with other geophysical logs, indicate transmissive fracture zones in each borehole. Pumping tests of each borehole indicated transmissivity ranges from <2 to 360 ft2 /day (0.2 to 33 m2 /day). Ground water appears to flow within an interconnected fracture network toward the south and west within the study area. No correlation was indicated between the fracture index and the total borehole transmissivity. 相似文献
Electromagnetic (EM) and heat-pulse flowmeter logs obtained under ambient and pumping conditions, together with other geophysical logs, indicate transmissive fracture zones in each borehole. Pumping tests of each borehole indicated transmissivity ranges from <2 to 360 ft
3.
A. D. Watkins 《Pure and Applied Geophysics》1991,137(3):221-232
The data collected in a well-to-well tomography experiment is inherently incomplete even when augmented by VSP data. The nature of the experiment suggests a geometric limitation to the resolution of any central structure.A parametric model has now been developed which examines the effect on reconstructed velocity due to the borehole size, transducer standoff, altered annulus, and the degree of velocity attenuation of the altered annulus, using a range of host velocities and hole separations.It was found that there are significant velocity variations caused by perturbations in borehole size. These errors are particularly significant for boreholes with large diameters and small transducer offsets. For an altered annulus, errors in both the dimensions and the degree of velocity alteration gave significant velocity variation in reconstructed velocity, particularly with large boreholes. In all cases it is observed that the variation and alteration in reconstructed velocities increased as hole separation is decreased. 相似文献
4.
Allen M. Shapiro 《Ground Water Monitoring & Remediation》2002,22(3):151-164
Collecting water samples for geochemical analyses in open bedrock boreholes or in discrete intervals of boreholes intersected by multiple fractures is likely to yield ambiguous results for ground water chemistry because of the variability in the transmissivity, storativity, and hydraulic head of fractures intersecting the borehole. Interpreting chemical analyses of water samples collected in bedrock boreholes requires an understanding of the hydraulic conditions in the borehole under the ambient flow regime in the aquifer as well as during sampling. Pumping in open boreholes, regardless of the pumping rate and the location of the pump intake, first draws water from the borehole and then from fractures intersecting the borehole. The time at which the volumetric rate of water entering the borehole from fractures is approximately equal to the pumping rate can be identified by monitoring the logarithm of drawdown in the borehole as a function of the logarithm of time. Mixing of water entering the borehole from fractures with water in the borehole must be considered in estimating the time at which the pump discharge is representative of aquifer water. In boreholes intersected by multiple fractures, after the contribution from the borehole volume has diminished, the contribution of fractures to the pump discharge will be weighted according to their transmissivity, regardless of the location of the pump intake. This results in a flux-averaged concentration in the pump discharge that is biased by the chemical signature of those fractures with the highest transmissivity. Under conditions where the hydraulic head of fractures varies over the length of the borehole, open boreholes will be subject to ambient flow in the water column in the borehole. In some instances, the magnitude of the ambient flow may be similar to the designated pumping rate for collecting water samples for geochemical analyses. Under such conditions, the contributions to the pump discharge from individual fractures will be a function not only of the transmissivity of the fractures, but also of the distribution of hydraulic head in fractures intersecting the borehole. To reduce or eliminate the deleterious effects of conducting geochemical sampling in open boreholes, a straddle-packer apparatus that isolates a single fracture or a series of closely spaced fractures is recommended. It is also recommended that open boreholes be permanently outfitted with borehole packers or borehole liners in instances where maintaining the hydraulic and chemical stratification in the aquifer is of importance. In a field example, a comparison of results from sampling in an open borehole and in discrete intervals of the same borehole showed dramatic differences in the concentrations of chemical constituents in the water samples, even though chemical field parameters stabilized prior to both open borehole and discrete interval sampling. 相似文献
5.
As landfill specifications become more stringent in the United Kingdom, the development of increasingly sophisticated monitoring methods is necessary to meet environmental protection goals. This case history describes the development of a 2-million-cubic-meter-capacity landfill located in a sandstone quarry and 1 km from a public water supply borehole, where the sensitivity of the site to ground water contamination and the proximity to a public water supply borehole are particular issues.
The landfill design incorporated a more sensitive environmental monitoring system, using a geophysical technique. The monitoring system comprises a permanent grid of electrodes installed beneath the landfill, connected by multicore cable to a computer-controlled earth resistance meter and switching unit in the site weighbridge. It was designed to detect holes in the landfill liner prior to and after covering with waste and to monitor the migration of contaminants beneath the landfill before they reach the perimeter observation boreholes, should leakage occur.
Such monitoring can enable the integrity of the landfill to be routinely reviewed; holes can be repaired if they are readily accessible and, if not, monitoring provides an early warning to enable the implementation of any additional monitoring or corrective action, based on the environmental risk posed by the site.
The system was first used as a quality assurance test once the landfill liner, which covered an area of 3 hectares, was installed. The system proved sensitive, detecting a hole consisting of two narrow knife cuts. Such sensitivity allows a high degree of confidence to be placed upon the integrity of the liner resulting in a significant contribution to public reassurance. The landfill is now operational, and monitoring using the geophysical system will be undertaken on a monthly basis for the first year, with the frequency of monitoring reviewed thereafter. 相似文献
The landfill design incorporated a more sensitive environmental monitoring system, using a geophysical technique. The monitoring system comprises a permanent grid of electrodes installed beneath the landfill, connected by multicore cable to a computer-controlled earth resistance meter and switching unit in the site weighbridge. It was designed to detect holes in the landfill liner prior to and after covering with waste and to monitor the migration of contaminants beneath the landfill before they reach the perimeter observation boreholes, should leakage occur.
Such monitoring can enable the integrity of the landfill to be routinely reviewed; holes can be repaired if they are readily accessible and, if not, monitoring provides an early warning to enable the implementation of any additional monitoring or corrective action, based on the environmental risk posed by the site.
The system was first used as a quality assurance test once the landfill liner, which covered an area of 3 hectares, was installed. The system proved sensitive, detecting a hole consisting of two narrow knife cuts. Such sensitivity allows a high degree of confidence to be placed upon the integrity of the liner resulting in a significant contribution to public reassurance. The landfill is now operational, and monitoring using the geophysical system will be undertaken on a monthly basis for the first year, with the frequency of monitoring reviewed thereafter. 相似文献
6.
从新疆乌鲁木齐市2004—2015年得到的841个钻孔中选择深度达30 m以下且钻孔资料记录完整的有效钻孔123个,通过计算5~30 m范围内不同深度的等效剪切波速,分别利用线性拟合、二次拟合和三次拟合对各深度vS（d）及其vS30进行拟合。通过对比发现,三个方程的拟合误差都随深度的增加而减少,且三次拟合方程的误差始终小于同深度的线性拟合和二次拟合方程,因此推荐使用三次拟合方程来估计新疆乌鲁木齐市钻孔的vS30值。同时将此结果和Boore的结果进行比较后发现,不同深度处的等效剪切波速vS（d）和vS30具有地域差异性;Boore得到的结果在钻孔深度小于20 m时明显高估vS30值,拟合曲线偏离实际数据点较远,所以本文拟合结果更适用于新疆乌鲁木齐市。综合比较可知,三次拟合得到的研究结果可以为新疆乌鲁木齐市钻孔深度不足30 m的地区求解vS30值提供参考。最后,利用新疆克拉玛依市2004—2015年钻孔资料检验三个拟合公式对克拉玛依市的适用性,发现深度越接近30 m,误差越小;线性模型和二次模型相对来说比较可靠,平均误差接近于0,并且对深度大于10 m的钻孔有高估现象;三次模型相对来说误差比较大,并且几乎在所有深度都有低估现象。 相似文献
7.
Fransson A 《Ground water》2002,40(2):201-204
The transmissivities of individual fractures along a borehole are difficult to obtain unless each fracture is tested. To estimate a fracture-transmissivity distribution from section transmissivities, a method was developed based on fixed-interval-length transmissivities and the corresponding number of fractures for each interval. The method is nonparametric and iterative, and the fractures are viewed as two-dimensional features, in which the total transmissivity of a borehole is equal to the sum of individual fracture transmissivities. Initially, a linear a priori assumption of the transmissivity distribution is made, and from this a so-called mean transmissivity function is derived. Subsequently, the mean transmissivity of the Nj fractures within a section, j, of the borehole is estimated, and the same value of the mean transmissivity function represents Nj possible fracture transmissivities from the initial distribution. This is repeated for each borehole section, and, eventually, all fracture transmissivities are sorted to give the next iteration's transmissivity distribution and the corresponding mean transmissivity function. Finally, the distributions converge, yielding a possible fracture-transmissivity distribution. The method was verified for a synthetic data sample and then tested on a sample from a borehole at the Asp? Hard Rock Laboratory, Sweden. For the synthetic data, the method gave a distribution that was fairly close to the original one; for the Asp? data, 15% of the fractures had a transmissivity larger than the measurement limit (1 x 10(-9) m2/sec), and these transmissivities follow a log-normal distribution. 相似文献
8.
9.
In granite aquifers, fractures can provide both storage volume and conduits for groundwater. Characterization of fracture hydraulic conductivity (K) in such aquifers is important for predicting flow rate and calibrating models. Nuclear magnetic resonance (NMR) well logging is a method to quickly obtain near-borehole hydraulic conductivity (i.e., KNMR) at high-vertical resolution. On the other hand, FLUTe flexible liner technology can produce a K profile at comparable resolution but requires a fluid driving force between borehole and formation. For three boreholes completed in a fractured granite, we jointly interpreted logging NMR data and FLUTe K estimates to calibrate an empirical equation for translating borehole NMR data to K estimates. For over 90% of the depth intervals investigated from these boreholes, the estimated KNMR are within one order of magnitude of KFLUTe. The empirical parameters obtained from calibrating the NMR data suggest that “intermediate diffusion” and/or “slow diffusion” during the NMR relaxation time may occur in the flowing fractures when hydraulic aperture are sufficiently large. For each borehole, “intermediate diffusion” dominates the relaxation time, therefore assuming “fast diffusion” in the interpretation of NMR data from fractured rock may lead to inaccurate KNMR estimates. We also compare calibrations using inexpensive slug tests that suggest reliable KNMR estimates for fractured rock may be achieved using limited calibration against borehole hydraulic measurements. 相似文献
10.
An approach to characterization of multilayer aquifer systems using open well borehole dilution is described. The approach involves measuring observation well flow velocities while a nearby extraction well is pumped by introducing a saline tracer into observation wells and collecting dilution vs. depth profiles. Inspection of tracer profile evolution allows discrete permeable layers within the aquifer to be identified. Dilution profiles for well sections between permeable layers are then converted into vertical borehole flow velocities and their evolution, using an analytic solution to the advection-dispersion equation applied to borehole flow. The dilution approach is potentially able to measure much smaller flow velocities that would be detectable using flowmeters. Vertical flow velocity data from the observation wells are then matched to those generated using a hydraulic model of the aquifer system, "shorted" by the observation wells, to yield the hydraulic properties of the constituent layers. Observation well flow monitoring of pumping tests represents a cost-effective alternative or preliminary approach to pump testing each layer of a multilayer aquifer system separately using straddle packers or screened wells and requires no prior knowledge of permeable layer depths and thicknesses. The modification described here, of using tracer dilution rather than flowmeter logging to obtain well flow velocities, allows the approach to be extended to greater well separations, thus characterizing a larger volume of the aquifer. An example of the application of this approach to a multilayer Chalk Aquifer in Yorkshire, Northeast England, is presented. 相似文献
11.
Martí Bayer-Raich Anthony Credoz Jordi Guimerà Salvador Jordana Diego Sampietro Jordi Font-Capó Nathalie Nief Matthieu Grossemy 《Ground water》2019,57(4):525-533
Currently, monitoring tools can be deployed in observation boreholes to better assess groundwater flow, flux of dissolved contaminants and their mass discharge in an aquifer. The relationship between horizontal water velocity in observation boreholes and Darcy fluxes in the surrounding aquifer has been studied for natural flow conditions (i.e., no pumping). Interpretation of measurements taken with dilution tests, the colloidal borescope, the Heat Pulse Flowmeter, and other techniques require the conversion of observed borehole velocity u to aquifer Darcy flux q∞ . This conversion is typically done through a proportionality factor α = u/q∞ . In experimental studies as well as in theoretical developments, reported values of α vary almost three orders of magnitude (from 0.5 to 10). This large variability in reported values of α could be explained by: (1) unclear distinction between Darcy flux and water seepage velocity, (2) unclear definition of water velocity in the borehole, (3) effects of well screen and the presence of the measurement device itself on the observable velocities, and (4) hydraulic conditions in the borehole annulus. We address (1), (2) from a conceptual/theoretical perspective, and (3) by means of numerical simulations. We show that issue (1) in low porosity aquifers can yield to order-of-magnitude discrepancies in estimates of q∞ ; (2) may result in discrepancies of up to 50%, and (3) can cause differences up to 20% of water velocity in the borehole void space compared to the theoretical case of an open borehole. 相似文献
12.
J.V. Herwanger M.H. Worthington † R. Lubbe † A. Binley J. Khazanehdari 《Geophysical Prospecting》2004,52(2):109-121
Cross‐hole anisotropic electrical and seismic tomograms of fractured metamorphic rock have been obtained at a test site where extensive hydrological data were available. A strong correlation between electrical resistivity anisotropy and seismic compressional‐wave velocity anisotropy has been observed. Analysis of core samples from the site reveal that the shale‐rich rocks have fabric‐related average velocity anisotropy of between 10% and 30%. The cross‐hole seismic data are consistent with these values, indicating that observed anisotropy might be principally due to the inherent rock fabric rather than to the aligned sets of open fractures. One region with velocity anisotropy greater than 30% has been modelled as aligned open fractures within an anisotropic rock matrix and this model is consistent with available fracture density and hydraulic transmissivity data from the boreholes and the cross‐hole resistivity tomography data. However, in general the study highlights the uncertainties that can arise, due to the relative influence of rock fabric and fluid‐filled fractures, when using geophysical techniques for hydrological investigations. 相似文献
13.
Signatures in flowing fluid electric conductivity logs 总被引：1，自引：0，他引：1
Flowing fluid electric conductivity logging provides a means to determine hydrologic properties of fractures, fracture zones, or other permeable layers intersecting a borehole in saturated rock. The method involves analyzing the time-evolution of fluid electric conductivity (FEC) logs obtained while the well is being pumped and yields information on the location, hydraulic transmissivity, and salinity of permeable layers. The original analysis method was restricted to the case in which flows from the permeable layers or fractures were directed into the borehole (inflow). Recently, the method was adapted to permit treatment of both inflow and outflow, including analysis of natural regional flow in the permeable layer. A numerical model simulates flow and transport in the wellbore during flowing FEC logging, and fracture properties are determined by optimizing the match between simulation results and observed FEC logs. This can be a laborious trial-and-error procedure, especially when both inflow and outflow points are present. Improved analyses methods are needed. One possible tactic would be to develop an automated inverse method, but this paper takes a more elementary approach and focuses on identifying the signatures that various inflow and outflow features create in flowing FEC logs. The physical insight obtained provides a basis for more efficient analysis of these logs, both for the present trial and error approach and for a potential future automated inverse approach. Inflow points produce distinctive signatures in the FEC logs themselves, enabling the determination of location, inflow rate, and ion concentration. Identifying outflow locations and flow rates typically requires a more complicated integral method, which is also presented in this paper. 相似文献
14.
Both approximate and exact formulations for the interaction of an incident elastic wave with a cased borehole are presented. In the approximate method, simple and explicit formulae are derived for the pressure in fluid at low frequencies. In the exact method, elastic potentials in each annulus are represented as a superposition of fundamental solutions to the Helmholtz equations. Continuity of displacements and stresses across layer boundaries are used to determine unknown coefficients. A global matrix algorithm is employed to compute simultaneously these coefficients in individual layers. Calculations show that, in cased boreholes, the borehole effects on downhole seismic measurements are more significant than in open boreholes. A strong resonance occurs in the fluid for SV-wave incidence from a soft formation. This resonance is prominent even at very high frequencies because the tube-wave velocity is raised well above the formation shear velocity by the steel pipe. At a particular angle of incidence of a plane P-wave, the pressure in the fluid is near zero at low frequencies (the cased borehole screening phenomenon). For hard formations and frequencies above 1 kHz, the cased borehole influence on a downhole geophone measurement is significant, especially at grazing incidence. For soft formations, both the pressure in the fluid and the solid displacement on the borehole wall show strong dependence on frequency and angle of incidence, even at low frequencies. 相似文献
15.
16.
Tracer tests represent the most appropriate approach for assessing hydrodispersive parameters such as transversal and longitudinal dispersivities or kinematic porosity on an aquifer scale. They are generally carried out by injecting a tracer in a borehole and measuring its concentration over time in neighboring boreholes by extracted volume sampling or downhole measurements. Logging is one of the most suitable methods for evaluating fissured reservoirs. But short circuits between fractures with different hydraulic potential through boreholes induce mixing phenomena that cannot be avoided without packers. This mixing can shift the breakthrough curves deduced from the logs for each producing fracture and distort determination of their location.
The method proposed in this paper aims at measuring the flow rate and the solute breakthrough for hydraulically active fractures, in open boreholes. It involves estimating a velocity profile along the borehole column by the analysis of two successive logs: a shift function according to depth is thus determined by comparison between log portions on each successive one. The velocity gradients reflect the inward or outward flow rates produced by each fracture. On the basis of these flow rates, it is possible to determine the mixing effects inside the borehole and then to plot unbiased breakthrough curves for each producing fracture.
This method was applied at a granitic site in the eastern Pyrenees. In spite of some questionable limitations, the results showed that the method seems adapted to situations with many fractures. The precise hydraulic pattern which is obtained at the borehole scale is discussed in terms of a dual porosity model. Furthermore, interpretation of the breakthrough curves for fractures corrected for mixing effects revealed that Peclet numbers are strongly underestimated if this phenomenon is not considered. 相似文献
The method proposed in this paper aims at measuring the flow rate and the solute breakthrough for hydraulically active fractures, in open boreholes. It involves estimating a velocity profile along the borehole column by the analysis of two successive logs: a shift function according to depth is thus determined by comparison between log portions on each successive one. The velocity gradients reflect the inward or outward flow rates produced by each fracture. On the basis of these flow rates, it is possible to determine the mixing effects inside the borehole and then to plot unbiased breakthrough curves for each producing fracture.
This method was applied at a granitic site in the eastern Pyrenees. In spite of some questionable limitations, the results showed that the method seems adapted to situations with many fractures. The precise hydraulic pattern which is obtained at the borehole scale is discussed in terms of a dual porosity model. Furthermore, interpretation of the breakthrough curves for fractures corrected for mixing effects revealed that Peclet numbers are strongly underestimated if this phenomenon is not considered. 相似文献
17.
—It is well known that electrical logs of boreholes can play a signi|fi|cant role in base metal exploration in identifying mineralised zones, especially when there is core loss or the borehole diameter is small or if drilling is by percussion. However, electrical logging is not widely utilised because of the additional burden on finances and time.¶A simple electrical logging technique, based on a pole-pole (hole-to-surface) configuration with one borehole electrode and nearly akin to the single point method, for S.P., resistivity and I.P. parameters, is presented. It is shown that it has the resolution of the single point method and the penetration of a very long normal sonde which is helpful for detection. Besides these features, the main advantage of this technique is that it can be easily carried out using ground I.P. (time domain) equipment.¶The electrical logs obtained in different base metal belts in Rajasthan, India, employing this technique and using ground I.P. equipment in connection with mise-à-la-masse surveys, illustrate the above features. A comparison with logs recorded by means of multi-electrode drill hole I.P. equipment of Scintrex, Canada, substantiates the same. 相似文献
18.
A microflow of free ascending gas has been observed in 26 out of 30 tested boreholes at three different sites. The flow rates vary between 60 × 10−4 and 4 cm3/min m2 horizontally projected borehole area. Sampling has been made in ground boreholes as well as in holes drilled downwards from the lowest levels in two mines. The composition of the gas varies considerably. The main components of the gas are nitrogen, argon, oxygen and methane. Traces of heavier hydrocarbons are observed. At the site of the ground holes, only traces of methane are observed. In all sampled holes the existence of free oxygen is observed. The nitrogen/argon quotient is close to the atmospheric quotient in all sampled holes, indicating a partly atmospheric origin of the gas. The existence of methane and traces of heavier hydrocarbons indicates the existence of a second source. 相似文献
19.
In contaminant hydrogeology, investigations at fractured rock sites are typically undertaken to improve understanding of the fracture networks and associated groundwater flow that govern past and/or future contaminant transport. Conventional hydrogeologic, geophysical, and hydrophysical techniques used to develop a conceptual model are often implemented in open boreholes under conditions of cross-connected flow. A new approach using high-resolution temperature (±0.001°C) profiles measured within static water columns of boreholes sealed using continuous, water-inflated, flexible liners (FLUTe™) identifies hydraulically active fractures under ambient (natural) groundwater flow conditions. The value of this approach is assessed by comparisons of temperature profiles from holes (100 to 200 m deep) with and without liners at four contaminated sites with distinctly different hydrogeologic conditions. The results from the lined holes consistently show many more hydraulically active fractures than the open-hole profiles, in which the influence of vertical flow through the borehole between a few fractures masks important intermediary flow zones. Temperature measurements in temporarily sealed boreholes not only improve the sensitivity and accuracy of identifying hydraulically active fractures under ambient conditions but also offer new insights regarding previously unresolvable flow distributions in fractured rock systems, while leaving the borehole available for other forms of testing and monitoring device installation. 相似文献
20.
Elaine M. FitzGerald Christopher J. Bean & Ronan Reilly 《Geophysical Prospecting》1999,47(6):1031-1044
Borehole-wall imaging is currently the most reliable means of mapping discontinuities within boreholes. As these imaging techniques are expensive and thus not always included in a logging run, a method of predicting fracture frequency directly from traditional logging tool responses would be very useful and cost effective. Artificial neural networks (ANNs) show great potential in this area. ANNs are computational systems that attempt to mimic natural biological neural networks. They have the ability to recognize patterns and develop their own generalizations about a given data set. Neural networks are trained on data sets for which the solution is known and tested on data not previously seen in order to validate the network result. We show that artificial neural networks, due to their pattern recognition capabilities, are able to assess the signal strength of fracture-related heterogeneity in a borehole log and thus fracture frequency within a borehole. A combination of wireline logs (neutron porosity, bulk density, P-sonic, S-sonic, deep resistivity and shallow resistivity) were used as input parameters to the ANN. Fracture frequency calculated from borehole televiewer data was used as the single output parameter. The ANN was trained using a back-propagation algorithm with a momentum learning function. In addition to fracture frequency within a single borehole, an ANN trained on a subset of boreholes in an area could be used for prediction over the entire set of boreholes, thus allowing the lateral correlation of fracture zones. 相似文献