共查询到16条相似文献，搜索用时 109 毫秒
1.
磷酸盐缓凝剂的优选与水泥复合浆液性能研究 总被引：3，自引：0，他引：3
研制了一种以无机聚合物（水玻璃）为速凝剂，以磷酸盐为缓凝剂配制而成的CWP水泥复合浆液。在该复合浆液中，用磷酸二氢铵作缓凝剂效果最好。CWP复合浆液在流变性，塑性强度，稳定性和结石强度上具有优良的性能。 相似文献
2.
在原硫木质素浆液的基础上，通过加入适量的无机物（D）可以得到一种新型硫木质素复合浆液，与以前的硫木质素液相比，硫木质素复合浆液强度更高，价格更低廉，浆液胶凝时间更易调控，这种性能优良的新型复合浆液在工程中将有良好的应用前景。 相似文献
3.
复杂地层钻进中常用的注浆材料需要良好的时间可控性和固结体强度,因此研制一种可控时间、增加固结体强度、效果良好的注浆浆液是有意义的。针对以上问题,利用正交试验的方法研制了一种复合注浆材料。在不饱和聚酯中添加水泥及引发剂、促进剂使浆液在要求时间内固化,最终配方的固化时间为62 min,抗压强度为32.6 MPa。该浆液作为化学浆液具有可注性好、浆液粘度低、能注入到细微裂隙中的优点,固结体强度高,并且塑性性能良好,由于在浆液中添加了水泥,降低了成本,较之一些化学浆液有一定的优势。 相似文献
4.
5.
普通硅酸盐-硫铝酸盐复合水泥浆液在地质灾害快速治理工程中具有广阔的应用前景,但复合浆液的流变特性直接影响到应用效果。采用理论分析与试验相结合的方法对不同配合比的普通硅酸盐-硫铝酸盐复合水泥浆液的流变特性进行了研究。根据试验结果绘制了复合水泥浆液的剪切应力-剪切速率变化曲线;通过测定浆液的表观粘度随时间的变化情况分析了水泥浆液粘度的时变特性。试验结果表明,水灰比对复合水泥浆液的流型有较明显的影响,减水剂对浆液的流型无明显影响,但对浆液的流变参数的数值影响较大,研究结果对于工程应用具有一定的指导意义。 相似文献
6.
《岩土力学》2020,(4)
针对高堆石坝坝体变形大且持续时间长的问题,提出了一种提高堆石体压缩模量、减缓流变变形的方法,即利用易流动、后期硬化的高掺粉煤灰水泥砂浆(简称复合浆液)在堆石体摊铺过程中充填堆石体孔隙,在施工碾压的基础上进一步减小堆石体孔隙率。首先通过观测复合浆液在透明玻璃球中的流动性态,研究不同配比与掺量对复合浆液流动特性的影响;然后通过侧限压缩和流变试验,研究掺复合浆液堆石料的压缩模量、流变变形的变化规律。试验结果表明:复合浆液在颗粒体孔隙中的流动性能与粉煤灰掺比、水胶比、砂粒最大粒径以及掺量有关;复合浆液的掺入能有效提高堆石料压缩模量,减少流变变形,且对于软岩料、级配不良料效果更为明显;复合浆液在堆石料中主要起到了充填、胶结与润滑作用。 相似文献
7.
针对高堆石坝坝体变形大且持续时间长的问题,提出了一种提高堆石体压缩模量、减缓流变变形的方法,即利用易流动、后期硬化的高掺粉煤灰水泥砂浆（简称复合浆液）在堆石体摊铺过程中充填堆石体孔隙,在施工碾压的基础上进一步减小堆石体孔隙率。首先,通过观测复合浆液在透明玻璃球中的流动性态,研究不同配比与掺量对复合浆液流动特性的影响;然后,通过侧限压缩和流变试验,研究掺复合浆液堆石料的压缩模量、流变变形的变化规律。试验结果表明：复合浆液在颗粒体孔隙中的流动性能与粉煤灰掺比、水胶比、砂粒最大粒径以及掺量有关;复合浆液的掺入能有效提高堆石料压缩模量,减少流变变形,且对于软岩料、级配不良料效果更为明显;复合浆液在堆石料中主要起到了充填、胶结与润滑作用。 相似文献
8.
《岩土力学》2021,(4)
针对高堆石坝坝体变形大且持续时间长的问题,提出了一种提高堆石体压缩模量、减缓流变变形的方法,即利用易流动、后期硬化的高掺粉煤灰水泥砂浆(简称复合浆液)在堆石体摊铺过程中充填堆石体孔隙,在施工碾压的基础上进一步减小堆石体孔隙率。首先通过观测复合浆液在透明玻璃球中的流动性态,研究不同配比与掺量对复合浆液流动特性的影响;然后通过侧限压缩和流变试验,研究掺复合浆液堆石料的压缩模量、流变变形的变化规律。试验结果表明:复合浆液在颗粒体孔隙中的流动性能与粉煤灰掺比、水胶比、砂粒最大粒径以及掺量有关;复合浆液的掺入能有效提高堆石料压缩模量,减少流变变形,且对于软岩料、级配不良料效果更为明显;复合浆液在堆石料中主要起到了充填、胶结与润滑作用。 相似文献
9.
水泥 水玻璃化学灌浆是把水泥、水玻璃按一定比例混合后形成的，这种浆液注入地基后，能将原松散地层的土粒和裂隙胶结成一个整体（“结石体”），其结构新，强度大，化学稳定性好，能彻底改善软弱地基土的物理和力学性质。水泥 水玻璃化学灌浆不仅具有水泥灌浆的优点，而且兼有化学浆液的一些特点。 相似文献
10.
采空区危害巨大,目前主要采用注浆充填方式进行处置。水泥-粉煤灰浆液在采空区治理中得到了广泛的应用,但在一些采空区治理工程中,由于缺乏粉煤灰,需要寻找其他低成本的注浆材料。水泥-黄土浆液具有就地取材、工艺简单等优势,是替代水泥-粉煤灰浆液的首选。本文以陕西泾阳、甘肃兰州、山西吕梁黄土为研究对象,通过大量水泥-黄土浆液黏度、结石率、凝结时间、结石体强度等性质的试验,研究了水泥掺量、水固比、黄土类型、水玻璃掺量等因素对水泥-黄土浆液性质及其结石体强度的影响。试验结果表明:随黄土掺量的增加,结石体强度、浆体流动性降低,而凝结时间延长;水泥-黄土浆液结石体早期强度较低,而后期强度增长较大;黄土的地域性分布,造成水泥-黄土浆液性质差异较大,黄土的粒径越粗,结石体的强度越高;与离石黄土浆液相比,马兰黄土浆液性能稳定,强度较高,更适宜于采空区充填注浆;水玻璃的掺入,使浆液黏度增大,结石率提高,凝结时间缩短,强度减小。本研究成果为采空区注浆设计和施工提供了新的思路。 相似文献
11.
《Geomechanics and Geoengineering》2013,8(2):86-96
This laboratory project aims to investigate the influence of polyvinyl acetate (PVA) grout injection on sandy soil improvement. In order to make the polymeric material injectable through the soil particles, adhesive polymer is mixed with water in certain weight percentages. Fine grained sand with different dry densities in its loose, medium and dense state, is prepared in a cylindrical mould and subjected to this polymeric grout injection. Unconfined compression tests are conducted on grouted samples after passing their curing period. Results illustrate that increasing the polymer percent in grout leads to significant compressive strength and elastic modulus enhancement. On the other hand, by increasing grout concentration, loose sand demonstrated higher compressive strength and elastic modulus improvement in comparison with medium and dense sand. 相似文献
12.
Ahmed Bayoumi 《Geotechnical and Geological Engineering》2011,29(1):75-90
Borehole extensometers are commonly utilized in field monitoring programs to measure settlement. In order to secure the targets of the extensometer, the borehole is typically backfilled with cement-bentonite grout. In the absence of standards for grout mix designs and due to non-universality of the properties of the backfilling grout, the accuracy of settlement furnished by borehole extensometers may be questionable. A preliminary parametric study was conducted to investigate the influence of grout stiffness on settlement measurements using borehole extensometers. The finite element program ABAQUS was used to model a borehole extensometer installed in an isotropic homogeneous elastic soil layer of a finite depth subjected to a uniform surface surcharge. Effect of the grout?Csoil elastic moduli ratio, soil/grout interface parameters (friction angle and shear strength), and extensometer embedment depth were investigated. Soil/grout interface behavior was assumed to comply with the elastic-perfectly plastic Coulomb friction model. The mechanism of measuring settlement using borehole extensometers was studied. The numerical study revealed that minimum errors in settlement can be obtained if the grout?Csoil elastic moduli ratio is made equal to about 1.0. Depending on the grout?Csoil moduli ratio, larger grout/soil interface friction angle and interface shear strength are generally associated with smaller settlement errors. Compared to fully embedded extensometers, partial embedment yields smaller settlement errors for grout?Csoil moduli ratio significantly above unity. In view of the findings of this preliminary parametric study, it is suggested to adopt the grout?Csoil moduli ratio in conjunction with grout compressive strength as the controlling criterion rather than the grout compressive strength only (current standard of practice). Additionally, it is evident that cement-bentonite grout mix should be carefully designed as part of the settlement monitoring programs to match the expected deformability (stiffness) of the soil mass under consideration. Future laboratory, field and numerical studies are needed to investigate more complex soil stratifications and to evaluate the behavior of various grout mixes. 相似文献
13.
针对隧道突水灾害防治对注浆材料的特殊要求,在水泥浆中加入外掺剂改善其力学特性与抗冲刷特性。通过测试不同水灰比、纤维掺量、硅灰掺量下水泥石的抗压与抗折强度,得出各水灰比下的强度最佳配合比,并测试最佳配合比下浆液的流动性与抗冲刷特性。试验发现,纤维与硅灰的掺入能够显著提高水泥石的强度,且对浆液的流动度影响不大;低流速下纤维硅灰水泥浆的抗冲刷特性较纯水泥浆改善显著,但流速较高时其抗冲刷特性仍较差。基于此,在纤维硅灰水泥浆中再掺入可再分散性乳胶粉进一步改善浆液抗冲刷特性。试验结果表明,可再分散性乳胶粉能明显改善浆液抗冲刷特性,即使在较高流速（0.6 m/s）下,其浆液留存率仍达到60%以上。研究结果为隧道突水灾害防治与动水注浆浆液选择提供了参考。 相似文献
14.
《Geomechanics and Geoengineering》2013,8(4):259-273
An important design parameter in cement-grouted soil nailed structures is the shear strength at the interface between the grouted nail and the surrounding soil. Both field and laboratory pull-out tests are normally used to investigate this interface shear strength. However, these tests have some limitations. In this study, direct shear box tests are adopted to investigate the interface shear strength behaviour between a completely decomposed granite (CDG) soil and a cement grout plate. Tests were carried out in a large direct shear test apparatus over a range of constant normal stress, soil moisture content, and soil–cement grout interface surface waviness. The laboratory test procedures are briefly described and the main test results are presented, followed by a discussion of the shear behaviour of the soil–cement grout interface. The interface shear behaviour is compared with the shear strength behaviour of the same soil tested under comparable conditions. It is shown that the shear stress–displacement behaviour of the soil–cement grout interface is similar to that of the soil alone. The test results indicate that the interface shear strength of the CDG and cement grout material depends on the normal stress level, the soil moisture content, and the interface surface waviness. 相似文献
15.
岩溶突水治理浆材的试验研究 总被引：3，自引：1，他引：2
以深部地下工程的加固和高压突水治理为研究对象,对一种新型化学注浆材料的化学反应封堵机制进行了可行性分析,并针对化学浆液的流动性、渗透性、抗冲刷性以及固结体的强度、水质毒理等因素进行了室内试验研究,详细地分析了浆液的物理化学特征,给出了浆液最佳配比值以及相应的性能指标。结合高压突水工程实例,开展现场注浆封堵试验,检验浆材用于突水封堵治理的可行性,并与超细水泥、水泥-水玻璃、尿醛树脂等常见注浆材料的封堵效果进行对比。试验结果表明：该化学浆液具有反应块、强度高、抗冲刷性强、无毒以及良好的渗透性和遇水膨胀功能,在现场应用中表现出良好的可控性和可泵性以及理想的注浆效果,与水泥类和一些常用化学浆材相比,具有运输快捷、配料方便、工艺简单的优点,所得结论对后续研究具有重要借鉴意义。 相似文献
16.
Composite element model for the bonded anchorage head of stranded wire cable in tension 总被引：1，自引：0，他引：1 
下载免费PDF全文
下载免费PDF全文 An elasto‐viscoplastic model is formulated using composite element technique for the bonded anchorage head of stranded wire cable in rock mass. This composite element contains sub‐elements corresponding to the rock material, the grout material, the stranded wire material, the rock/grout interface, and the grout/stranded wire interface, respectively. The displacement in each aforementioned sub‐element is interpolated from the corresponding nodal displacements of the composite element. In this manner, the mesh generation taking into account of tension cable anchors may be highly facilitated. By the application of the virtual work principle, the governing equation for solving the nodal displacements of the composite element is established. The proposed model has been incorporated into the conventional finite element algorithm and implemented in the program CORE3, in which the anchorage head is embedded within the composite elements. The comparative study concerning the pull‐out test has been carried out for the validation of the proposed model and algorithm. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献