首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 46 毫秒
1.
Accuracy of the Copernicus snow water equivalent (SWE) product and the impact of SWE calibration and assimilation on modelled SWE and streamflow was evaluated. Daily snowpack measurements were made at 12 locations from 2016 to 2019 across a 4104 km2 mixed-forest basin in the Great Lakes region of central Ontario, Canada. Sub-basin daily SWE calculated from these sites, observed discharge, and lake levels were used to calibrate a hydrologic model developed using the Raven modelling framework. Copernicus SWE was bias corrected during the melt period using mean bias subtraction and was compared to daily basin average SWE calculated from the measured data. Bias corrected Copernicus SWE was assimilated into the models using a range of parameters and the parameterizations from the model calibration. The bias corrected Copernicus product agreed well with measured data and provided a good estimate of mean basin SWE demonstrating that the product shows promise for hydrology applications within the study region. Calibration to spatially distributed SWE substantially improved the basin scale SWE estimate while only slightly degrading the flow simulation demonstrating the value of including SWE in a multi-objective calibration formulation. The particle filter experiments yielded the best SWE estimation but moderately degraded the flow simulation. The particle filter experiments constrained by the calibrated snow parameters produced similar results to the experiments using the upper and lower bounds indicating that, in this study, model calibration prior to assimilation was not valuable. The calibrated models exhibited varying levels of skill in estimating SWE but demonstrated similar streamflow performance. This indicates that basin outlet streamflow can be accurately estimated using a model with a poor representation of distributed SWE. This may be sufficient for applications where estimating flow is the primary water management objective. However, in applications where understanding the physical processes of snow accumulation, melt and streamflow generation are important, such as assessing the impact of climate change on water resources, accurate representations of SWE are required and can be improved via multi-objective calibration or data assimilation, as demonstrated in this study.  相似文献   

2.
Remote sensing is an important source of snow‐cover extent for input into the Snowmelt Runoff Model (SRM) and other snowmelt models. Since February 2000, daily global snow‐cover maps have been produced from data collected by the Moderate Resolution Imaging Spectroradiometer (MODIS). The usefulness of this snow‐cover product for streamflow prediction is assessed by comparing SRM simulated streamflow using the MODIS snow‐cover product with streamflow simulated using snow maps from the National Operational Hydrologic Remote Sensing Center (NOHRSC). Simulations were conducted for two tributary watersheds of the Upper Rio Grande basin during the 2001 snowmelt season using representative SRM parameter values. Snow depletion curves developed from MODIS and NOHRSC snow maps were generally comparable in both watersheds: satisfactory streamflow simulations were obtained using both snow‐cover products in larger watershed (volume difference: MODIS, 2·6%; NOHRSC, 14·0%) and less satisfactory streamflow simulations in smaller watershed (volume difference: MODIS, −33·1%; NOHRSC, −18·6%). The snow water equivalent (SWE) on 1 April in the third zone of each basin was computed using the modified depletion curve produced by the SRM and was compared with in situ SWE measured at Snowpack Telemetry sites located in the third zone of each basin. The SRM‐calculated SWEs using both snow products agree with the measured SWEs in both watersheds. Based on these results, the MODIS snow‐cover product appears to be of sufficient quality for streamflow prediction using the SRM in the snowmelt‐dominated basins. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

3.
Reliable estimation of the volume and timing of snowmelt runoff is vital for water supply and flood forecasting in snow‐dominated regions. Snowmelt is often simulated using temperature‐index (TI) models due to their applicability in data‐sparse environments. Previous research has shown that a modified‐TI model, which uses a radiation‐derived proxy temperature instead of air temperature as its surrogate for available energy, can produce more accurate snow‐covered area (SCA) maps than a traditional TI model. However, it is unclear whether the improved SCA maps are associated with improved snow water equivalent (SWE) estimation across the watershed or improved snowmelt‐derived streamflow simulation. This paper evaluates whether a modified‐TI model produces better streamflow estimates than a TI model when they are used within a fully distributed hydrologic model. It further evaluates the performance of the two models when they are calibrated using either point SWE measurements or SCA maps. The Senator Beck Basin in Colorado is used as the study site because its surface is largely bedrock, which reduces the role of infiltration and emphasizes the role of the SWE pattern on streamflow generation. Streamflow is simulated using both models for 6 years. The modified‐TI model produces more accurate streamflow estimates (including flow volume and peak flow rate) than the TI model, likely because the modified‐TI model better reproduces the SWE pattern across the watershed. Both models also produce better performance when calibrated with SCA maps instead of point SWE data, likely because the SCA maps better constrain the space‐time pattern of SWE.  相似文献   

4.
The spatial and temporal distribution of snow cover extent (SCE) and snow water equivalent (SWE) play vital roles in the hydrology of northern watersheds. We apply remotely sensed Special Sensor Microwave Imager (SSM/I) data from 1988 to 2007 to explore the relationships between snow distribution and the hydroclimatology of the Mackenzie River Basin (MRB) of Canada and its major sub-basins. The Environment Canada (EC) algorithm is adopted to retrieve the SWE from SSM/I data. Moderate Resolution Imaging Spectroradiometer (MODIS) 8-day maximum snow cover extent products (MOD10A2) are used to estimate the different thresholds of retrieved SWE from SSM/I to classify the land cover as snow or no snow for various sub-basins in the MRB. The sub-basins have varying topography and hence different thresholds that range from 10 mm to 30 mm SWE. The accuracy of snow cover mapping based on the combination of several thresholds for the different sub-basins reaches ≈ 90%. The northern basins are found to have stronger linear relationships between the date on which snow cover fraction (SCF) reaches 50% or when SWE reaches 50% and mean air temperatures, than the southern basins. Correlation coefficients between SCF, SWE, and hydroclimatological variables show the new SCF products from SSM/I perform better than SWE from SSM/I to analyze the relationships with the regional hydroclimatology. Statistical models relating SCF and SWE to runoff indicate that the SCF and SWE from EC algorithms are able to predict the discharge in the early snow ablation seasons in northern watersheds.  相似文献   

5.
Land surface albedo plays an important role in the radiation budget and global climate models. NASA's Moderate Resolution Imaging Spectroradiometer (MODIS) provide 16‐day albedo product with 500‐m resolution every 8 days (MCD43A3). Some in‐situ albedo measurements were used as the true surface albedo values to validate the MCD43A3 product. As the 16‐day MODIS albedo retrievals do not include snow observations when there is ephemeral snow on the ground surface in a 16‐day period, comparisons between MCD43A3 and 16 day averages of field data do not agree well. Another reason is that the MODIS cannot detect the snow when the area is covered by clouds. The Advanced Microwave Scanning Radiometer for EOS (AMSR‐E) data are not affected by weather conditions and are a good supplement for optical remote sensing in cloudy weather. When the surface is covered by ephemeral snow, the AMSR‐E data can be used as the additional information to retrieve the snow albedo. In this study, we developed an improved method by using the MODIS products and the AMSR‐E snow water equivalent (SWE) product to improve the MCD43A3 short‐time snow‐covered albedo estimation. The MODIS daily snow products MOD10A1 and MYD10A1 both provide snow and cloud information from observations. In our study region, we updated the MODIS daily snow product by combining MOD10A1 and MYD10A1. Then, the product was combined with the AMSR‐E SWE product to generate new daily snow‐cover and SWE products at a spatial resolution of 500 m. New SWE datasets were integrated into the Noah Land Surface Model snow model to calculate the albedo above a snow surface, and these values were then utilized to improve the MODIS 16‐day albedo product. After comparison of the results with in‐situ albedo measurements, we found that the new corrected 16‐day albedo can show the albedo changes during the short snowfall season. For example, from January 25 to March 14, 2007 at the BJ site, the albedo retrieved from snow‐free observations does not indicate the albedo changes affected by snow; the improved albedo conforms well to the in‐situ measurements. The correlation coefficient of the original MODIS albedo and the in‐situ albedo is 0.42 during the ephemeral snow season, but the correlation coefficient of the improved MODIS albedo and the in‐situ albedo is 0.64. It is concluded that the new method is capable of capturing the snow information from AMSR‐E SWE to improve the short‐time snow‐covered albedo estimation. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

6.
In this study, the spatial and temporal variabilities of terrestrial water storage anomaly (TWSA) and snow water equivalent anomaly (SWEA) information obtained from the Gravity Recovery and Climate Experiment (GRACE) twin satellites data were analysed in conjunction with multisource snow products over several basins in the Canadian landmass. Snow water equivalent (SWE) data were extracted from three different sources: Global Snow Monitoring for Climate Research version 2 (GlobSnow2), Advanced Microwave Scanning Radiometer-Earth Observing System (AMSR-E), and Canadian Meteorological Centre (CMC). The objective of the study was to understand whether SWE variations have a significant contribution to terrestrial water storage anomalies in the Canadian landmass. The period was considered from December 2002 to March 2011. Significant relationships were observed between TWSA and SWEA for most of the 15 basins considered (53% to 80% of the basins, depending on the SWE products considered). The best results were obtained with the CMC SWE products compared with satellite-based SWE data. Stronger relationships were found in snow-dominated basins (Rs > = 0.7), such as the Liard [root mean square error (RMSE) = 21.4 mm] and Peace Basins (RMSE = 26.76 mm). However, despite high snow accumulation in the north of Quebec, GRACE showed weak or insignificant correlations with SWEA, regardless of the data sources. The same behaviour was observed in the Western Hudson Bay basin. In both regions, it was found that the contribution of non-SWE compartments including wetland, surface water, as well as soil water storages has a significant impact on the variations of total storage. These components were estimated using the Water-Global Assessment and Prognosis Global Hydrology Model (WGHM) simulations and then subtracted from GRACE observations. The GRACE-derived SWEA correlation results showed improved relationships with three SWEA products. The improvement is particularly important in the sub-basins of the Hudson Bay, where very weak and insignificant results were previously found with GRACE TWSA data. GRACE-derived SWEA showed a significant relationship with CMC data in 93% of the basins (13% more than GRACE TWSA). Overall, the results indicated the important role of SWE on terrestrial water storage variations.  相似文献   

7.
Snowmelt drives a large portion of streamflow in many mountain areas of the world. However, the water paths from snowmelt to the arrival of the water in the streams are still largely unknown. This work analyzes for first time the influence of snowmelt on spring streamflow with different snow accumulation and duration, in an alpine catchment of the central Spanish Pyrenees. This study presents the water balance of the main melting months (May and June). Piezometric values, water temperature, electrical conductivity and isotope data (δ18O) allow a better understanding of the hydrological functioning of the basin during these months. Results of the water balance calculations showed that snow represented on average 73% of the water available for streamflow in May and June while precipitation during these months accounted for only 27%. However, rainfall during the melting period was important to determine the shape of the spring hydrographs. On average, 78% of the sum of both the snow water equivalent (SWE) accumulated at the beginning of May and the precipitation in May and June converted into runoff during the May–June melting period. The average evaporation-sublimation during the 2 months corresponded to 8.4% of the accumulated SWE and rainfall, so that only a small part of the water input was ultimately available for soil and groundwater storage. When snow cover disappeared from the catchment, soil water storage and streamflow showed a sharp decline. Consequently, streamflow electrical conductivity, temperature and δ18O showed a marked tipping point towards higher values. The fast hydrological response of the catchment to snow and meteorological fluctuations, as well as the marked diel fluctuations of streamflow δ18O during the melting period, strongly suggests short meltwater transit times. As a consequence of this hydrological behaviour, independently of the amount of snow accumulated and of melting date, summer streamflow remained always low, with only small runoff peaks driven by rainfall events.  相似文献   

8.
This paper describes a data assimilation method that uses observations of snow covered area (SCA) to update hydrologic model states in a mountainous catchment in Colorado. The assimilation method uses SCA information as part of an ensemble Kalman filter to alter the sub-basin distribution of snow as well as the basin water balance. This method permits an optimal combination of model simulations and observations, as well as propagation of information across model states. Sensitivity experiments are conducted with a fairly simple snowpack/water-balance model to evaluate effects of the data assimilation scheme on simulations of streamflow. The assimilation of SCA information results in minor improvements in the accuracy of streamflow simulations near the end of the snowmelt season. The small effect from SCA assimilation is initially surprising. It can be explained both because a substantial portion of snowmelts before any bare ground is exposed, and because the transition from 100% to 0% snow coverage occurs fairly quickly. Both of these factors are basin-dependent. Satellite SCA information is expected to be most useful in basins where snow cover is ephemeral. The data assimilation strategy presented in this study improved the accuracy of the streamflow simulation, indicating that SCA is a useful source of independent information that can be used as part of an integrated data assimilation strategy.  相似文献   

9.
The hydrology of boreal regions is strongly influenced by seasonal snow accumulation and melt. In this study, we compare simulations of snow water equivalent (SWE) and streamflow by using the hydrological model HYDROTEL with two contrasting approaches for snow modelling: a mixed degree‐day/energy balance model (small number of inputs, but several calibration parameters needed) and the thermodynamic model CROCUS (large number of inputs, but no calibration parameter needed). The study site, in Northern Quebec, Canada was equipped with a ground‐based gamma ray sensor measuring the SWE continuously for 5 years in a small forest clearing. The first simulation of CROCUS showed a tendency to underestimate SWE, attributable to bias in the meteorological inputs. We found that it was appropriate to use a threshold of 2 °C to separate rain and snow. We also applied a correction to account for snowfall undercatch by the precipitation gauge. After these modifications to the input dataset, we noticed that CROCUS clearly overestimated the SWE, likely as a result of not including loss in SWE because of blowing snow sublimation and relocation. To correct this, we included into CROCUS a simple parameterisation effective after a certain wind speed threshold, after which the thermodynamic model performed much better than the traditional mixed degree‐day/energy balance model. HYDROTEL was then used to simulate streamflow with both snow models. With CROCUS, the main peak flow could be captured, but the second peak because of delayed snowmelt from forested areas could not be reproduced due to a lack of sub‐canopy radiation data to feed CROCUS. Despite the relative homogeneity of the boreal landscape, data inputs from each land cover type are needed to generate satisfying simulation of the spring runoff. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

10.
The US Army ERDC CRREL and the US Department of Agriculture Natural Resources Conservation Service developed a square electronic snow water equivalent (e‐SWE) sensor as an alternative to using fluid‐filled snow pillows to measure SWE. The sensors consist of a centre panel to measure SWE and eight outer panels to buffer edge stress concentrations. Seven 3 m square e‐SWE sensors were installed in five different climate zones. During the 2011–2012 winter, 1.8 and 1.2 m square e‐SWE sensors were installed and operated in Oregon. With the exception of New York State and Newfoundland, the e‐SWE sensors accurately measured SWE, with R2 values between the sensor and manual SWE measurements of between 0.86 and 0.98. The e‐SWE sensor at Hogg Pass, Oregon, accurately measured SWE during the past 8 years of operations. In the thin, icy snow of New York during midwinter 2008–2009, the e‐SWE sensors overmeasured SWE because of edge stress concentrations associated with strong icy layers and a shallow snow cover. The New York e‐SWE sensors' measurement accuracy improved in spring 2009 and further improved during the 2011–2012 winter with operating experience. At Santiam Junction, measured SWE from the 1.8 and 1.2 m square e‐SWE sensors agreed well with the snow pillow, 3 m square e‐SWE sensor, and manual SWE measurements until February 2013, when dust and gravel blew onto the testing area resulting in anomalous measurements. © 2014 The Authors. Hydrological Processes published by John Wiley & Sons Ltd.  相似文献   

11.
Comparisons between snow water equivalent (SWE) and river discharge estimates are important in evaluating the SWE fields and to our understanding of linkages in the freshwater cycle. In this study, we compared SWE drawn from land surface models and remote sensing observations with measured river discharge (Q) across 179 Arctic river basins. Over the period 1988‐2000, basin‐averaged SWE prior to snowmelt explains a relatively small (yet statistically significant) fraction of interannual variability in spring (April–June) Q, as assessed using the coefficient of determination (R2). Averaged across all basins, mean R2s vary from 0·20 to 0·28, with the best agreement noted for SWE drawn from a simulation with the Pan‐Arctic Water Balance Model (PWBM) forced with data from the European Centre for Medium‐Range Weather‐Forecasts (ECMWF) Re‐analysis (ERA‐40). Variability and magnitude in SWE derived from Special Sensor Microwave Imager (SSM/I) data are considerably lower than the variability and magnitude in SWE drawn from the land surface models, and generally poor agreement is noted between SSM/I SWE and spring Q. We find that the SWE versus Q comparisons are no better when alternate temporal integrations–using an estimate of the timing in basin thaw–are used to define pre‐melt SWE and spring Q. Thus, a majority of the variability in spring discharge must arise from factors other than basin snowpack water storage. This study demonstrates how SWE estimated from remote sensing observations, or general circulation models (GCMs), can be evaluated effectively using monthly discharge data or SWE from a hydrological model. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

12.
As demand for water continues to escalate in the western Unites States, so does the need for accurate monitoring of the snowpack in mountainous areas. In this study, we describe a simple methodology for generating gridded‐estimates of snow water equivalency (SWE) using both surface observations of SWE and remotely sensed estimates of snow‐covered area (SCA). Multiple regression was used to quantify the relationship between physiographic variables (elevation, slope, aspect, clear‐sky solar radiation, etc.) and SWE as measured at a number of sites in a mountainous basin in south‐central Idaho (Big Wood River Basin). The elevation of the snowline, obtained from the SCA estimates, was used to constrain the predicted SWE values. The results from the analysis are encouraging and compare well to those found in previous studies, which often utilized more sophisticated spatial interpolation techniques. Cross‐validation results indicate that the spatial interpolation method produces accurate SWE estimates [mean R2 = 0·82, mean mean absolute error (MAE) = 4·34 cm, mean root mean squared error (RMSE) = 5·29 cm]. The basin examined in this study is typical of many mid‐elevation mountainous basins throughout the western United States, in terms of the distribution of topographic variables, as well as the number and characteristics of sites at which the necessary ground data are available. Thus, there is high potential for this methodology to be successfully applied to other mountainous basins. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

13.
Time series of fractional snow covered area (SCA) estimates from Landsat Enhanced Thematic Mapper (ETM+), Moderate Resolution Imaging Spectroradiometer (MODIS), and Advanced Very High Resolution Radiometer (AVHRR) data were combined with a spatially distributed snowmelt model to reconstruct snow water equivalent (SWE) in the Rio Grande headwaters (3419 km2). In this reconstruction approach, modeled snowmelt over each pixel is integrated during the period of satellite-observed snow cover to estimate SWE. Due to underestimates in snow cover detection, maximum basin-wide mean SWE using MODIS and AVHRR were, respectively, 45% and 68% lower than SWE estimates obtained using ETM+ data. The mean absolute error (MAE) of SWE estimated at 100-m resolution using ETM+ data was 23% relative to observed SWE from intensive field campaigns. Model performance deteriorated when MODIS (MAE = 50%) and AVHRR (MAE = 89%) SCA data were used. Relative to differences in the SCA products, model output was less sensitive to spatial resolution (MAE = 39% and 73% for ETM+ and MODIS simulations run at 1 km resolution, respectively), indicating that SWE reconstructions at the scale of MODIS acquisitions may be tractable provided the SCA product is improved. When considering tradeoffs between spatial and temporal resolution of different sensors, our results indicate that higher spatial resolution products such as ETM+ remain more accurate despite the lower frequency of acquisition. This motivates continued efforts to improve MODIS snow cover products.  相似文献   

14.
In this study, we compare gridded snow depth estimates from the Snow Data Assimilation System (SNODAS) with snow depth observations derived from GPS interferometric reflectometry (GPS‐IR) from roughly 100 Plate Boundary Observatory sites in the Western United States spanning four water‐years (2010–2013). Data from these sites are not assimilated by SNODAS; thus, GPS‐IR measurements provide an independent data set to evaluate SNODAS. Our results indicate that at 80% of the sites, SNODAS and GPS‐IR snow depth agree to better than 15‐cm root mean square error, with correlation coefficients greater than 0.6. Significant differences are found between GPS‐IR and SNODAS for sites that are distant from other point measurements, are located in complex terrain or are in areas with strong vegetation heterogeneities. GPS‐IR estimates of snow depth are shown to provide useful error characterization of SNODAS products across much of the Western United States and may have potential as an additional data assimilation source that could help improve SNODAS estimates. © 2014 The Authors. Hydrological Processes published by John Wiley & Sons Ltd.  相似文献   

15.
Snow water equivalent (SWE) is an important indicator used in hydrology, water resources, and climate change impact. There are various methods of estimating SWE (falling in 3 categories: indirect sensors, empirical models, and process‐based models), but few studies that provide comparison across these different categories to help users make decisions on monitoring site design or method selection. Five SWE estimation methods were compared against manual snow course data collected over 2 years (2015–2016) from the Dorset Environmental Science Centre, including the gamma‐radiation‐based CS725 sensor, 3 empirical estimation models (Sexstone snow density model, McCreight & Small snow density model, and a meteorology‐based model), and the University of British Columbia Watershed Model snow energy‐balance model. Snow depth, density, and SWE were measured at the Dorset Environmental Science Centre weather station in south‐central Ontario, on a daily basis over 6 winters from 2011 to 2016. The 2 snow density‐based models, requiring daily snow depth as input, gave the best performance (R2 of .92 and .92 for McCreight & Small and Sexstone models, respectively). The CS725 sensor that receives radiation coming from soil penetrating the snowpack provided the same performance (R2 = .92), proving that the sensor is an applicable method, although it is expensive. The meteorology‐based empirical model, requiring daily climate data including temperature, precipitation and solar radiation, gave the poorest performance (R2 = .77). The energy‐balance‐based University of British Columbia Watershed Model snow module, only requiring climate data, worked better than the empirical meteorology‐based model (R2 = .9) but performed worse than the density models or CS725 sensor. Given differences in application objectives, site conditions, and budget, this comparison across SWE estimation methods may help users choose a suitable method. For ongoing and new monitoring sites, installation of a CS725 sensor coupled with intermittent manual snow course measurements (e.g., weekly) is recommended for further SWE method estimation testing and development of a snow density model.  相似文献   

16.
Abstract

We simulated snow processes in a forested region with heavy snowfall in Japan, and evaluated both the regional-scale snow distribution and the potential impact of land-use changes on the snow cover and water balances over the entire domain. SnowModel reproduced the snow processes at open and forested sites, which were confirmed by snow water equivalent (SWE) measurements at two intensive observation sites and snow depth measurements at the Automated Meteorological Data Acquisition System sites. SnowModel also reproduced the observed snow distribution (from the MODIS snow cover data) over the simulation domain during thaw. The observed SWE was less at the forested site than at the open site. The SnowModel simulations showed that this difference was caused mainly by differences in sublimation. The type of land use changed the maximum SWE, onset and duration of snowmelt, and the daily snowmelt rate due to canopy snow interception.

Citation Suzuki, K., Kodama, Y., Nakai, T., Liston, G. E., Yamamoto, K., Ohata, T., Ishii, Y., Sumida, A., Hara, T. & Ohta, T. (2011) Impact of land-use changes in a forested region with heavy snowfall in Hokkaido, Japan. Hydrol. Sci. J. 56(3), 443–467.  相似文献   

17.
Snowpack water equivalent (SWE) is a key variable for water resource management in snow-dominated catchments. While it is not feasible to quantify SWE at the catchment scale using either field surveys or remotely sensed data, technologies such as airborne LiDAR (light detection and ranging) support the mapping of snow depth at scales relevant to operational water management. To convert snow depth to water equivalent, models have been developed to predict SWE or snowpack density based on snow depth and additional predictor variables. This study builds upon previous models that relate snowpack density to snow depth by including additional predictor variables to account for (1) long-term climatologies that describe the prevailing conditions influencing regional snowpack properties, and (2) the effect of intra- and inter-year variability in meteorological conditions on densification through a cumulative degree-day index derived from North American Regional Reanalysis products. A non-linear model was fit to 114 506 snow survey measurements spanning 41 years from 1166 snow courses across western North America. Under spatial cross-validation, the predicted densities had a root-mean-square error of 47.1 kg m−3, a mean bias of −0.039 kg m−3, and a Nash-Sutcliffe Efficiency of 0.70. The model developed in this study had similar overall performance compared to a similar regression-based model reported in the literature, but had reduced seasonal biases. When applied to predict SWE from simulated depths with random errors consistent with those obtained from LiDAR or Structure-from-Motion, 50% of the SWE estimates for April and May fell within −45 to 49 mm of the observed SWE, representing prediction errors of −15% to 20%.  相似文献   

18.
Abstract

Winter mean 700-hectoPascal (hPa) height anomalies, representing the average atmospheric circulation during the snow season, are compared with annual streamflow measured at 140 streamgauges in the western United States. Correlation and anomaly pattern analyses are used to identify relationships between winter mean atmospheric circulation and temporal and spatial variability in annual streamflow. Results indicate that variability in winter mean 700-Hpa height anomalies accounts for a statistically significant portion of the temporal variability in annual streamflow in the western United States. In general, above-average annual streamflow is associated with negative winter mean 700-Hpa height anomalies over the eastern North Pacific Ocean and/or the western United States. The anomalies produce an anomalous flow of moist air from the eastern North Pacific Ocean into the western United States that increases winter precipitation and snowpack accumulations, and subsequently streamflow. Winter mean 700-hPa height anomalies also account for statistically significant differences in spatial distributions of annual streamflow. As part of this study, winter mean atmospheric circulation patterns for the 40 years analysed were classified into five winter mean 700-hPa height anomaly patterns. These patterns are related to statistically significant and physically meaningful differences in spatial distributions of annual streamflow.  相似文献   

19.
The retrieval of Snow Water Equivalent (SWE) from remote sensing satellites continues to be a very challenging problem. In this paper, we evaluate the accuracy of a new SWE product derived from the blending of a passive microwave SWE product based on the Advanced Microwave Sounding Unit (AMSU) with a multi‐sensor snow cover extent product based on the Interactive Multi‐sensor Snow and Ice Mapping System (IMS). The microwave measurements have the ability to penetrate the snow pack, and thus, the retrieval of SWE is best accomplished using the AMSU. On the other hand, the IMS maps snow cover more reliably due to the use of multiple satellite and ground observations. The evolution of global snow cover from the blended, the AMSU and the IMS products was examined during the 2006 snow season. Despite the overall good inter‐product agreement, it was shown that the retrievals of snow cover extent in the blended product are improved when using IMS, with implications for improved microwave retrievals of SWE. In a separate investigation, the skill of the microwave SWE product was also examined for its ability to correctly estimate SWE globally and regionally. Qualitative evaluation of global SWE retrievals suggested dependence on land surface temperature: the lower the temperature, the higher the SWE retrieved. This temperature bias was attributed in part to temperature effects on those snow properties that impact microwave response. Therefore, algorithm modifications are needed with more dynamical adjustments to account for changing snow cover. Quantitative evaluation over Slovakia in central Europe, for a limited period in 2006, showed reasonably good performance for SWE less than 100 mm. Sensitivity to deeper snow decreased significantly. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

20.
Abstract

Abstract Results of studies related to the effect of snow accumulation and snowmelt on river regimes of the central Spanish Pyrenees are presented. Streamflow of the Pyrenean rivers is characterized by low and constant discharges during winter because of accumulation of snow in the basins above 1600 m a.s.l., and high and fluctuating discharges during spring due to snowmelt and rainfall. Regional discharge contrasts have been assessed in relation to the Atlantic influence and the percentage of high altitude areas in each basin. In most of the Pyrenean basins, snowmelt contributes more to the discharge than rainfall in the spring. The analysis of data shows a decrease in winter precipitation in the last 50 years causing a decrease in both winter and spring discharges and introducing changes in the distribution of streamflow throughout the year.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号