首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
ASTM Standards instruct experimenters to use circular or square bearing plates/footings having areas ranging between 0.073 and 0.456 m2. In general, researchers and contractors perform loading bearing plate/footing tests using plates/footings which have dimensions exceeding the ones recommended by the Standards. This paper offers formulas describing relationships between settlements of square and circular plates/footings having areas ranging between 0.5 and 4.0 m2 and deformation zones developing beneath them. The proposed formulas are verified by the results of field tests performed with circular and square plates or footings supported by cohesive soils.  相似文献   

2.
非均质地基承载力及破坏模式的FLAC数值分析   总被引：3，自引：0，他引：3  
利用基于Lagrangian显式差分的FLAC算法，通过数值计算，对黏结力随深度线性增长的非均质地基上条形基础和圆形基础的极限承载力及地基破坏模式进行了对比计算与系统分析。研究表明：（1）随着地基黏结力沿深度非均匀变化系数的增大，地基的破坏范围逐渐集中在地基表层和基础两侧：（2）即使地基的非均质程度较小，当将非均质地基近似地按均质地基考虑时，由此所估算的承载力可能过于保守；（3）地基承载力系数随黏结力沿深度非均匀变化系数的增大而非线性地增大。与数值解相比，skempton与Peck等近似公式均可能高估了非均质地基承载力。  相似文献   

3.
This paper focuses on the effective utilization of pond ash, as foundation medium. A series of laboratory model tests have been carried out using square, rectangular and strip footings on pond ash. The effects of dry density, degree of saturation of pond ash, size and shape of footing on ultimate bearing capacity of shallow foundations are presented in this paper. Local shear failure of a square footing on pond ash at 37% moisture content (optimum moisture content) is observed up to the values of dry density 11.20 kN/m3 and general shear failure takes place at the values of dry density 11.48 kN/m3 and 11.70 kN/m3. Effects of degree of saturation on ultimate bearing capacity were studied. Experimental results show that degree of saturation significantly affects the ultimate bearing capacity of strip footing. The effect of footing length to width ratio (L/B), on increase in ultimate bearing capacity of pond ash, is insignificant for L/B ≥ 10 in case of rectangular footings. The effects of size of footing on ultimate bearing capacity for all shapes of footings viz., square, rectangular and strip footings are highlighted.  相似文献   

4.
In this paper, finite element analysis is used to predict the undrained bearing capacity of strip, square and circular footings resting on layered clays. The soil profile consists of two clay layers with different thicknesses and properties. The results are compared with previous solutions for strip footings on layered clays. The bearing-capacity behaviour is discussed and the bearing-capacity factors are given for various cases involving a range of layer thicknesses and properties of the two clay soil layers.  相似文献   

5.
The influence of a non-coaxial model for granular soils on shallow foundation analyses is investigated. The non-coaxial plasticity theory proposed by Rudnicki and Rice (J. Mech. Phys. Solids 1975, 23, 371–394) is integrated into a Drucker–Prager model with both perfect plasticity and strain hardening. This non-coaxial model is numerically implemented into the finite-element program ABAQUS using a substepping scheme with automatic error control. The influence of the non-coaxial model on footing settlement and bearing capacity is investigated under various loading and boundary conditions. Compared with the predictions using conventional coaxial models, the non-coaxial prediction results indicate that the settlement of a footing increases significantly when the non-coaxial component of plastic strain rate is taken into consideration, although ultimate footing bearing capacities are not affected significantly. The non-coaxial model has a different effect on footing settlements under different loading and boundary conditions. In general, the discrepancies between coaxial and non-coaxial predictions increase with increasing rotation of principal stresses of the soil mass beneath a footing. It can be concluded that if the non-coaxial component of plastic strain rate is neglected in shallow foundation problems using the finite-element method, the results tend to be non-conservative when designs are dominated by settlement of footings.  相似文献   

6.
The classical solution to the bearing capacity problem predicts the limit load on symmetrically loaded shallow strip footings. A useful hypothesis was suggested by Meyerhof to account for eccentricity of loading, in which the footing width is reduced by twice-the-eccentricity to its ‘effective’ size. This hypothesis sometimes has been criticized as being overconservative. This paper examines Meyerhof’s suggestion and presents the bearing capacity of eccentrically loaded footings calculated using the kinematic approach of limit analysis. It is found that the effective width rule yields a bearing capacity equivalent to that calculated based on the assumption that the footing is smooth. For more realistic footing models and for cohesive soils the effective width rule is a reasonable account of eccentricity in bearing capacity calculations. Only for significant bonding at the soil-footing interface and for large eccentricities does the effective width rule become overly conservative. For cohesionless soils, however, the effective width rule may overestimate the best upper bound. This overestimation increases with an increase in eccentricity. ©  相似文献   

7.
Measured settlements of buildings on the weathered Keuper Marl appeared to be much smaller than calculated settlements, which were based on stiffness modulus from standard oedometer tests. Therefore, both special triaxial K 0-tests and oedometer tests were carried out for an accurate determination of stiffness moduli. Modulus obtained in the triaxial K 0-tests were at least two to three times the values obtained in the oedometer tests. To verify observations from the laboratory tests, the loads and the settlements of two single footings on weathered Keuper mudstone have been measured during construction of a building over 1 year. Also, a large scale footing load test with measurements of deformations were conducted on the weathered Keuper mudstone. The measured settlements of the two single footings and the tested foundation were compared with the settlements based on conventional calculations with moduli from oedometer tests and triaxial K 0-tests. Up to a foundation pressure of σv = 500 kN/m2 the calculated settlement based on E S-modulus obtained from triaxial K 0-tests was found to correspond well to the measured deformation. For foundation pressure beyond 500 kN/m2, the foundation response was highly non-linear and it could not be described any more with the linear-elastic model. Therefore the footing load test was also simulated by FEM analyses.  相似文献   

8.
The pull-out resistance of reinforcing elements is one of the most significant factors in increasing the bearing capacity of geosynthetic reinforced soils. In this research a new reinforcing element that includes elements (anchors) attached to ordinary geogrid for increasing the pull-out resistance of reinforcements is introduced. Reinforcement therefore consists of geogrid and anchors with cubic elements that attached to the geogrid, named (by the authors) Grid-Anchor. A total of 45 load tests were performed to investigate the bearing capacity of square footing on sand reinforced with this system. The effect of depth of the first reinforcement layer, the vertical spacing, the number and width of reinforcement layers, the distance that anchors are effective, effect of relative density, low strain stiffness and stiffness after local shear were investigated. Laboratory tests showed that when a single layer of reinforcement is used there is an optimum reinforcement embedment depth for which the bearing capacity is the greatest. There also appeared to be an optimum vertical spacing of reinforcing layers for multi-layer reinforced sand. The bearing capacity was also found to increase with increasing number of reinforcement layer, if the reinforcement were placed within a range of effective depth. The effect of soil density also is investigated. Finally the results were compared with the bearing capacity of footings on non-reinforced sand and sand reinforced with ordinary geogrid and the advantages of the Grid-Anchor were highlighted. Test results indicated that the use of Grid-Anchor to reinforce the sand increased the ultimate bearing capacity of shallow square footing by a factor of 3.0 and 1.8 times compared to that for un-reinforced soil and soil reinforced with ordinary geogrid, respectively.  相似文献   

9.
By using small scale model tests, the interference effect on the vertical load-deformation behavior of a number of equally spaced strip footings, placed on the surface of dry sand, was investigated. At any stage, all the footings were assumed to (i) carry exactly equal magnitude of load, and (ii) settle to the same extent. No tilt of the footing was permitted. The effect of clear spacing (s) among footings on the results was explored. A new experimental setup was proposed in which only one footing needs to be employed rather than a number of footings. The bearing capacity increases continuously with decrease in spacing among the footings. The interference effect becomes further prominent with increase in soil friction angle. In contrast to an increase in the bearing capacity, with decrease in spacing of footings, an increase in the footing settlement associated with the ultimate state of shear failure was observed. The present experimental observations were similar to those predicted by the available theory, based on the method of characteristics. As compared to the theory, the present experimental data, however, indicates much greater effect of interference especially for larger spacing among footings.  相似文献   

10.
In recent times, rapid urbanisation coupled with scarcity of land forces several structures to come up ever closer to each other, which may sometime cause severe damage to the structures from both strength and serviceability point of view, and therefore, a need is felt to devise simplified methods to capture the effect of footing interference. In the present study, an attempt has been made to model the settlement behaviour of two strip footings placed in close spacing on layered soil deposit consisting of a strong top layer underlying a weak bottom layer. Theory of elasticity is employed to derive the governing differential equations and subsequently solved by the finite difference method. The perfectly rough strip footings are considered to be resting on the surface of two-layer soil system, and the soil is assumed to behave as linear elastic material under a range of static foundation load. The effect of various parameters such as the elastic moduli and thickness of two layers, clear spacing between the footings and footing load on the settlement behaviour of closely spaced footings has been determined. The variation of vertical normal stress at the interface of two different soil layers as well as at the base of the failure domain also forms an important part of this study. The results are presented in terms of settlement ratio (ξδ), and their variation is obtained with the change in clear spacing between two footings. The present theoretical investigation indicates that the settlement of closely spaced footings is found to be higher than that of single isolated footing, which further reduces with increase in the spacing between the footings.  相似文献   

11.
Ring footings can be more effective and economical than circular footings. In spite of similarities between circular and ring footings, their behaviors are different in some respects such as bearing pressure distribution under the footing and settlement. But no exclusive theoretical prediction of ultimate bearing capacity has been reported for ring footings. In the present study, stress characteristics method is employed for coding the bearing capacity of ring footing with horizontal ground surface. In the calculations, friction at the contact between the soil and foundation is considered. In this research, the soil obeys the Mohr–Coulomb yield criterion and that is cohesive–frictional-weighted with applied surcharge pressure. The bearing capacity factors Nγ, Nq and Nc for ring footings were calculated by a written code based on the method of characteristics. Bearing capacity was determined for different conditions of soil and different ratio of radii in comparison with the principle of superposition results. The findings show that the principle of superposition is effective for determining the bearing capacity of a ring footing.  相似文献   

12.
In this paper, given an estimate of the bearing capacity of the soil, by treating settlement at a given load as a random variable and the evolution of settlement of footing on cohesionless soil with the increasing load as a stochastic process, a tri-level homogeneous Markov chain (TLHMC) model is proposed for prediction of settlement. Comparison of the predicted mean and bounds on settlements, obtained using TLHMC, with the respective field values obtained from literature shows that the stochastic evolution can be modelled using TLHMC with a correlation coefficient of 0.90. A methodology for reliability-based design of footings is also presented and its use is demonstrated through a numerical example.  相似文献   

13.
The stability of eccentrically loaded strip footings on slopes was investigated using the method of finite element analysis based on the theory of elasto-plasticity. The analysis was done for two different soils involving three levels of slope angle, six footing locations, and two levels of load eccentricity plus central vertical loading. The strip footing analysed was a 3-ft (0.9 m) wide reinforced concrete footing embedded to a depth of 3 ft (0.9 m). The analysis focused on footing settlement, plastic yielding of soil, and ultimate bearing capacity. The results of analysis show that the influence of load eccentricity on footing pressure vs. footing centre settlement is negligibly small. However, the progressive soil yielding and ultimate bearing capacity are greatly affected by load eccentricity. Furthermore, the effect of load eccentricity differs considerably with the load location relative to the footing centre and slope crest. The ultimate bearing capacity for the eccentric load located on the slope side is significantly greater than that for the load located on the other side of the footing centre. For a 2(H): 1(V) slope in silty clay, the effect of slope on footing stability decreases with increasing footing location from slope crest as would be expected, and diminishes when the footing is located from the crest at about 5-times the footing width.  相似文献   

14.
This research proposes the use of artificial neural network to predict the allowable bearing capacity and elastic settlement of shallow foundation on granular soils in Sharjah, United Arab Emirates. Data obtained from existing soil reports of 600 boreholes were used to train and validate the model. Three parameters (footing width, effective unit weight, and SPT blow count) are considered to have the most significant impact on the magnitude of allowable bearing capacity and elastic settlement of shallow foundations, and thus were used as the model inputs. Throughout the study, depth of footing was limited to 1.5 m below existing ground level and water table depth taken at the level of the footing. Performance comparison of the developed models (in terms of coefficient of determination, root mean square error, and mean absolute error) revealed that the developed artificial neural network models could be effectively used for predicting the allowable bearing capacity and elastic settlement. As such, the developed models can be used at the preliminary stage of estimating the allowable bearing capacity and settlements of shallow foundations on granular soils, instead of the conventional methods.  相似文献   

15.
Bally, R.J., 1988. Some specific problems of wetted loessial soils in civil engineering. Eng. Geol., 25: 303–324.

Loessial soils, wetted above the limit of collapsibility, remain in the category of difficult foundation grounds. Some case histories are presented herein: surpassing soil bearing capacity and non-stabilized settlements of buildings after initially dry loess wetting; slow but nondamped settlements or damped but great and, eventually, non-uniform settlements of structures erected on wet loess; supplementary settlements by water level lowering in loessial ground; great settlements of deep foundations passing through the collapsible loess to the underlaying wet but noncollapsible loess. Research on wetted loess performed in the laboratory (oedometer, triaxial) or in situ (full-scale experiments or real constructions) have emphasized the dependence of the soil structural resistance, deformability (compressibility and deformation under constant volume) and final resistance on both the moisture content or stress-state and on their history; the depth propagation of the active zone of surface loadings on wetted loess is different from that of the linear elastic theory; some suggestions to estimate the depth of the active zone are presented. The usual foundation systems on wetted loessial grounds, or in their vicinity, adopted in Romania include: loessial or gravel cushions; surface compaction (very efficient results of intensive dynamic compaction); foundation “stamping” or loessial ground “reinforcing”. It is recommendable to take into consideration: surveyed wetting under construction until maximum moisture content of the loessial ground; in situ columns of stabilized loess; the efficiency of geotextiles for filter-drainage and antierosional functions in loessial soils.  相似文献   


16.
Current studies of bearing capacity for shallow foundations tend to rely on the hypothesis of an isolated footing. In practice a footing is never isolated; it is mostly in interaction with other footings. This paper focuses on a numerical study using the finite-difference code Fast Lagrangian Analysis of Continua (FLAC), to evaluate the bearing capacity for two interfering strip footings, subjected to centered vertical loads with smooth and rough interfaces. The soil is modeled by an elasto-plastic model with a Mohr–Coulomb yield criterion and associative flow rule. The interference effect is estimated by efficiency factors, defined as the ratio of the bearing capacity for a single footing in the presence of the other footing to that of the single isolated footing. The efficiency factors have been computed individually to estimate the effects of cohesion, surcharge, and soil weight using Terzaghi’s equation, both in a frictional soil with surcharge pressures and in a cohesive-frictional soil with surcharge pressures. The results have been compared with those available in the literature.  相似文献   

17.
This paper examines the drained bearing response of circular footings resting on structured soil deposits. Numerical simulations have been carried out using a finite element formulation of the Structured Cam Clay model. A parametric study was conducted by varying the parameters that govern the behaviour of structured soils and guidelines are given for designers to identify when effects of the soil structure are important. Under fully drained conditions, deformation within the structured soil supporting the footing usually occurs as a local or punching shear failure due to high compressibility of the structured soil and the mobilised bearing pressure increases with the footing movement, without reaching an ultimate value. A novel approximate method is presented to obtain the load–displacement response of a rigid circular footing resting on the surface of a structured soil deposit. This requires the properties of the soil in the reconstituted state and two additional parameters, which govern the natural structure of the soil. The proposed method has been applied to a published case study, where plate load test results are given for rigid circular steel plates resting on structured soil deposits. Fair agreement is observed between the computed and experimental results, suggesting the approximate method may be useful in design studies of foundations on structured soil deposits.  相似文献   

18.
The ultimate bearing capacity of a group of equally spaced multiple rough strip footings was determined due to the contribution of soil unit weight. The analysis was performed by using an upper bound theorem of limit analysis in combination with finite elements and linear programming. Along the interfaces of all the triangular elements, velocity discontinuities were considered. The value of ξγ was found to increase continuously with a decrease in S/B, where (i) ξγ is the ratio of the failure load of an interfering strip footing of a given width (B) to that of a single isolated strip footing having the same width and (ii) S is the clear spacing between any two adjacent footings. The effect of the variation of spacing on ξγ was found to be very extensive for small values of S/B; ξγ approaches infinity at S/B=0. In all the cases, the velocity discontinuities were found to exist generally in a zone only around the footing edge. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

19.
The ultimate bearing capacity of two closely spaced strip footings, placed on a cohesionless medium and loaded simultaneously to failure at the same magnitude of failure load, was determined by using an upper bound limit analysis. A logarithmic spiral radial shear zone, comprising of a number of triangular rigid blocks, was assumed to exist around each footing edge. The equations of the logarithmic spiral arcs were based on angles φL and φR rather than soil friction angle φ; the values of φL and φR were gradually varied in between 0 and φ. The ultimate bearing capacity was found to become maximum corresponding to a certain critical spacing between the footings. For spacing greater than the critical, the bearing capacity was found to decrease continuously with increase in the spacing. The extent of the spacing corresponding to which the ultimate bearing capacity becomes either maximum or equal to that of a single isolated footing increases with increase in φ. The results compare reasonably well with the available theoretical and experimental data.  相似文献   

20.
This paper presents a study on the bearing capacity of eccentrically-loaded rough ring footings resting over cohesionless soil. To this aim, a series of 3D numerical simulations were performed using the finite difference method. In order to consider the effect of load eccentricity, reduction factor method is applied. In this method, the ratio of an eccentrically-loaded bearing capacity to the bearing capacity of the same footing under vertical load is defined. Comparison between the results of the numerical simulations with those of analytical solutions and experimental data indicates good agreement. A mathematical expression is also introduced for eccentrically-loaded ring footings.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号