共查询到20条相似文献，搜索用时 31 毫秒
1.
Karl Koch 《Pure and Applied Geophysics》2010,167(4-5):401-412
Quantitative modeling of infrasound signals and development and verification of the corresponding atmospheric propagation models requires the use of well-calibrated sources. Numerous sources have been detected by the currently installed network of about 40 of the final 60 IMS infrasound stations. Besides non-nuclear explosions such as mining and quarry blasts and atmospheric phenomena like auroras, these sources include meteorites, volcanic eruptions and supersonic aircraft including re-entering spacecraft and rocket launches. All these sources of infrasound have one feature in common, in that their source parameters are not precisely known and the quantitative interpretation of the corresponding signals is therefore somewhat ambiguous. A source considered well-calibrated has been identified producing repeated infrasound signals at the IMS infrasound station IS26 in the Bavarian forest. The source results from propulsion tests of the ARIANE-5 rocket’s main engine at a testing facility near Heilbronn, southern Germany. The test facility is at a range of 320 km and a backazimuth of ~280° from IS26. Ground-truth information was obtained for nearly 100 tests conducted in a 5-year period. Review of the available data for IS26 revealed that at least 28 of these tests show signals above the background noise level. These signals are verified based on the consistency of various signal parameters, e.g., arrival times, durations, and estimates of propagation characteristics (backazimuth, apparent velocity). Signal levels observed are a factor of 2–8 above the noise and reach values of up to 250 mPa for peak amplitudes, and a factor of 2–3 less for RMS measurements. Furthermore, only tests conducted during the months from October to April produce observable signals, indicating a significant change in infrasound propagation conditions between summer and winter months. 相似文献
2.
In order to discriminate between quarry blasts and earthquakes observed in the Dobrogea seismogenic region, a seismo-acoustic analysis was performed on 520 events listed in the updated Romanian seismic catalogue from January 2011 to December 2012. During this time interval, 104 seismo-acoustic events observed from a distance between 110 and 230 km and backazimuth interval of 110–160° from the IPLOR infrasound array were identified as explosions by associating with infrasonic signals. WinPMCC software for interactive analysis was applied to detect and characterize infrasonic signals in terms of backazimuth, speed and frequency content. The measured and expected values of both backazimuths and arrival times for the study events were compared in order to identify the sources of infrasound. Two predominant directions for seismo-acoustic sources’ aligning were observed, corresponding to the northern and central parts of Dobrogea, and these directions are further considered as references in the process of discriminating explosions from earthquakes. A predominance of high-frequency detections (above 1 Hz) is also observed in the infrasound data. The strong influence of seasonally dependent stratospheric winds on the IPLOR detection capability limits the efficiency of the discrimination procedure, as proposed by this study. 相似文献
3.
Stromboli Volcano in Italy is a persistently active, complex volcanic system. In May 2002 activity was confined to 3 major summit craters within which several active vents hosted multiple explosions each hour. During a 5-day field campaign an array of 3 low-frequency microphones was installed to investigate the coherent infrasound produced by degassing from these vents. Consistent phase lags across the 3 stations indicate distinct sources that are subsequently investigated to determine the associated vent location, apparent depth, and origin time. The cross-correlation routine allows for variations in comparison window length, waveform filtering bandwidth, and correlation and consistency thresholds, allowing for improved detection of certain types of degassing sources. Identification of activity at the various vents could be subsequently corroborated with 3 channels of synchronously acquired thermal data and video. During the May 2002 experiment persistent, energetic infrasound was observed from a passive degassing source within the Central Crater (CC) and transient infrasound, produced by discrete Strombolian explosions, was identified at 4 additional vents. The continuous infrasound produced by the CC exhibits variable frequency-dependent correlation lag times that are interpreted as a diffraction effect due to the acoustic radiators recessed location within a steep-walled crater. Such dispersion has important implications for accurate eruption source modeling because it indicates that infrasonic waveforms may be significantly filtered during propagation. Transient explosion signals from the Northeast Crater (NEC) and Southwest Crater (SWC) vents also exhibit dynamic correlation lag times, but this scatter may be more reasonably attributed to variable epicentral locations. Explosions from the NEC west vent, for instance, appear to emanate from a diffuse zone with a lateral extent in excess of 10 m.Editorial responsibility: R. Cioni 相似文献
4.
—?Official Russian sources in 1996 and 1997 have stated that 340 underground nuclear tests (UNTs) were conducted during 1961–1989 at the Semipalatinsk Test Site (STS) in Eastern Kazakhstan. Only 271 of these nuclear tests appear to have been described with well-determined origin time, coordinates and magnitudes in the openly available technical literature. Thus, good open documentation has been lacking for 69 UNTs at STS.¶The main goal of our study was to provide detections, estimates of origin time and location, and magnitudes, for as many of these previously undocumented events as possible. We used data from temporary and permanent seismographic stations in the former USSR at distances from 500?km to about 1500?km from STS. As a result, we have been able to assign magnitude for eight previously located UNTs whose magnitude was not previously known. For 31 UNTs, we have estimated origin time an d assigned magnitude — and for 19 of these 31 we have obtained locations based on seismic signals. Of the remaining 30 poorly documented UNTs, 15 had announced yields that were less than one ton, and 13 occurred simultaneously with another test which was detected. There are only two UNTs, for which the announced yield exceeds one ton and we have been unable to find seismic signals.¶Most of the newly detected and located events were sub-kiloton. Their magnitudes range from 2.7 up to 5.1 (a multi-kiloton event on 1965 Feb. 4 that was often obscured at teleseismic stations by signals from an earthquake swarm in the Aleutians).¶For 17 small UNTs at STS, we compare the locations (with their uncertainties) that we had earlier determined in 1994 from analysis of regional seismic waves, with ground-truth information obtained in 1998. The average error of the seismically-determined locations is only about 5?km. The ground-truth location is almost alw ays within the predicted small uncertainty of the seismically-determined location.¶Seismically-determined yield estimates are in good agreement with the announced total annual yield of nuclear tests, for each year from 1964 to 1989 at Semipalatinsk.¶We also report the origin time, location, and seismic magnitude of 29 chemical explosions and a few earthquakes on or near STS during the years 1961–1989.¶Our new documentation of STS explosions is important for evaluating the detection, location, and identification capabilities of teleseismic and regional arrays and stations; and how these capabilities have changed with time. 相似文献
5.
In the monitoring of earthquakes and nuclear explosions using a sparse worldwide network of seismic stations, it is frequently
necessary to make reliable location estimates using a single seismic array. It is also desirable to screen out routine industrial
explosions automatically in order that analyst resources are not wasted upon detections which can, with a high level of confidence,
be associated with such a source. The Kovdor mine on the Kola Peninsula of NW Russia is the site of frequent industrial blasts
which are well recorded by the ARCES regional seismic array at a distance of approximately 300 km. We describe here an automatic
procedure for identifying signals which are likely to result from blasts at the Kovdor mine and, wherever possible, for obtaining
single array locations for such events. Carefully calibrated processing parameters were chosen using measurements from confirmed
events at the mine over a one-year period for which the operators supplied Ground Truth information. Phase arrival times are
estimated using an autoregressive method and slowness and azimuth are estimated using broadband f{-}k analysis in fixed frequency bands and time-windows fixed relative to the initial P-onset time. We demonstrate the improvement
to slowness estimates resulting from the use of fixed frequency bands. Events can be located using a single array if, in addition
to the P-phase, at least one secondary phase is found with both an acceptable slowness estimate and valid onset-time estimate.
We evaluate the on-line system over a twelve month period; every event known to have occured at the mine is detected by the
process and 32 out of 53 confirmed events were located automatically. The remaining events were classified as “very likely”
Kovdor events and were subsequently located by an analyst. The false alarm rate is low; only 84 very likely Kovdor events
were identified during the whole of 2003 and none of these were subsequently located at a large distance from the mine. The
location accuracy achieved automatically by the single-array process is remarkably good, and is comparable to that obtained
interactively by an experienced analyst using two-array observations. The greatest problem encountered in the single array
location procedure is the difficulty in determining arrival times for secondary phases, given the weak Sn phase and the complexity
of the P-coda. The method described here could be applied to a wide range of locations and sources for which the monitoring
of seismic activity is desirable. The effectiveness will depend upon the distance between source and receiver, the nature
of the seismic sources and the level of regional seismicity. 相似文献
6.
The global monitoring of earthquakes and explosions at decreasing magnitudes necessitates the fully automatic detection, location and classification of an ever increasing number of seismic events. Many seismic stations of the International Monitoring System are small-aperture arrays designed to optimize the detection and measurement of regional phases. Collaboration with operators of mines within regional distances of the ARCES array, together with waveform correlation techniques, has provided an unparalleled opportunity to assess the ability of a small-aperture array to provide robust and accurate direction and slowness estimates for phase arrivals resulting from well-constrained events at sites of repeating seismicity. A significant reason for the inaccuracy of current fully-automatic event location estimates is the use of f?k slowness estimates measured in variable frequency bands. The variability of slowness and azimuth measurements for a given phase from a given source region is reduced by the application of almost any constant frequency band. However, the frequency band resulting in the most stable estimates varies greatly from site to site. Situations are observed in which regional P- arrivals from two sites, far closer than the theoretical resolution of the array, result in highly distinct populations in slowness space. This means that the f?k estimates, even at relatively low frequencies, can be sensitive to source and path-specific characteristics of the wavefield and should be treated with caution when inferring a geographical backazimuth under the assumption of a planar wavefront arriving along the great-circle path. Moreover, different frequency bands are associated with different biases meaning that slowness and azimuth station corrections (commonly denoted SASCs) cannot be calibrated, and should not be used, without reference to the frequency band employed. We demonstrate an example where fully-automatic locations based on a source-region specific fixed-parameter template are more stable than the corresponding analyst reviewed estimates. The reason is that the analyst selects a frequency band and analysis window which appears optimal for each event. In this case, the frequency band which produces the most consistent direction estimates has neither the best SNR or the greatest beam-gain, and is therefore unlikely to be chosen by an analyst without calibration data. 相似文献
7.
Perspectives of Cross-Correlation in Seismic Monitoring at the International Data Centre 总被引：1，自引：0，他引：1
We demonstrate that several techniques based on waveform cross-correlation are able to significantly reduce the detection threshold of seismic sources worldwide and to improve the reliability of arrivals by a more accurate estimation of their defining parameters. A master event and the events it can find using waveform cross-correlation at array stations of the International Monitoring System (IMS) have to be close. For the purposes of the International Data Centre (IDC), one can use the spatial closeness of the master and slave events in order to construct a new automatic processing pipeline: all qualified arrivals detected using cross-correlation are associated with events matching the current IDC event definition criteria (EDC) in a local association procedure. Considering the repeating character of global seismicity, more than 90 % of events in the reviewed event bulletin (REB) can be built in this automatic processing. Due to the reduced detection threshold, waveform cross-correlation may increase the number of valid REB events by a factor of 1.5–2.0. Therefore, the new pipeline may produce a more comprehensive bulletin than the current pipeline—the goal of seismic monitoring. The analysts’ experience with the cross correlation event list (XSEL) shows that the workload of interactive processing might be reduced by a factor of two or even more. Since cross-correlation produces a comprehensive list of detections for a given master event, no additional arrivals from primary stations are expected to be associated with the XSEL events. The number of false alarms, relative to the number of events rejected from the standard event list 3 (SEL3) in the current interactive processing—can also be reduced by the use of several powerful filters. The principal filter is the difference between the arrival times of the master and newly built events at three or more primary stations, which should lie in a narrow range of a few seconds. In this study, one event at a distance of about 2,000 km from the main shock was formed by three stations, with the stations and both events on the same great circle. Such spurious events are rejected by checking consistency between detections at stations at different back azimuths from the source region. Two additional effective pre-filters are f–k analysis and F prob based on correlation traces instead of original waveforms. Overall, waveform cross-correlation is able to improve the REB completeness, to reduce the workload related to IDC interactive analysis, and to provide a precise tool for quality check for both arrivals and events. Some major improvements in automatic and interactive processing achieved by cross-correlation are illustrated using an aftershock sequence from a large continental earthquake. Exploring this sequence, we describe schematically the next steps for the development of a processing pipeline parallel to the existing IDC one in order to improve the quality of the REB together with the reduction of the magnitude threshold. 相似文献
8.
The presence of man-made explosions in a seismic catalogue leads to errors in statistical analyses of seismicity. Recently, the need to monitor man-made explosions used for mining, road excavating, and other constructional applications has been become a demanding challenge for the seismologists. In this way, we gain new insight into the cross-correlation technique and conduct this approach to discriminate explosions from seismic datasets. Following this, improved P-wave arrival times are used for more precise relocation. In this study, the waveform cross-correlation technique provides a reliable means for discriminating explosions which have cross-correlation coefficients (CC) of 0.6 or greater with their own corresponding stacked waveforms. The results illustrate that approximately 80 % of seismicity of southeast of Tehran, recorded by the Iranian Seismological Center (IRSC), includes events which have cross-correlation coefficients of ≥0.6 with their corresponding stacked waveforms. Furthermore, with improved P-wave arrival time, there is a better chance to relocate explosions precisely in the region under study. 相似文献
9.
P. Montalto A. Cannata E. Privitera S. Gresta G. Nunnari D. Patanè 《Pure and Applied Geophysics》2010,167(10):1215-1231
Active volcanoes characterized by open conduit conditions generate sonic and infrasonic signals, whose investigation provides useful information for both monitoring purposes and studying the dynamics of explosive processes. In this work, we discuss the automatic procedures implemented for a real-time application to the data acquired by a permanent network of five infrasound stations running at Mt. Etna volcano. The infrasound signals at Mt. Etna consist in amplitude transients, called infrasound events. The adopted procedure uses a multi-algorithm approach for event detection, counting, characterization and location. It is designed for an efficient and accurate processing of infrasound records provided by single-site and array stations. Moreover, the source mechanism of these events can be investigated off-line or in near real-time by using three different models: (1) Strombolian bubble; (2) resonating conduit and (3) Helmholtz resonator. The infrasound waveforms allow us to choose the most suitable model, to get quantitative information about the source and to follow the time evolution of the source parameters. 相似文献
10.
The detection and location of low magnitude earthquakes in northern Norway using multi-channel waveform correlation at regional distances 总被引：1，自引：0，他引：1
Steven J. Gibbons Mathilde Bttger Srensen David B. Harris Frode Ringdal 《Physics of the Earth and Planetary Interiors》2007,160(3-4):285-309
A fortuitous sequence of closely spaced earthquakes in the Rana region of northern Norway, during 2005, has provided an ideal natural laboratory for investigating event detectability using waveform correlation over networks and arrays at regional distances. A small number of events between magnitude 2.0 and 3.5 were recorded with a high SNR by the Fennoscandian IMS seismic arrays at distances over 600 km and three of these events, including the largest on 24 June, displayed remarkable waveform similarity even at relatively high frequencies. In an effort to detect occurrences of smaller earthquakes in the immediate geographical vicinity of the 24 June event, a multi-channel correlation detector for the NORSAR array was run for the whole calender year 2005 using the signal from the master event as a template. A total of 32 detections were made and all but 2 of these coincided with independent correlation detections using the other Nordic IMS array stations; very few correspond to signals detectable using traditional energy detectors. Permanent and temporary stations of the Norwegian National Seismic Network (NNSN) at far closer epicentral distances have confirmed that all but one of the correlation detections at NORSAR in fact correspond to real events. The closest stations at distances of approximately 10 km can confirm that the smallest of these events have magnitudes down to 0.5 which represents a detection threshold reduction of over 1.5 for the large-aperture NORSAR array and over 1.0 for the almost equidistant regional ARCES array. The incompleteness of the local network recordings precludes a comprehensive double-difference location for the full set of events. However, stable double-difference relative locations can be obtained for eight of the events using only the Lg phase recorded at the array stations. All events appear to be separated by less than 0.5 km. Clear peaks were observed in the NORSAR correlation coefficient traces during the coda of some of the larger events; the local stations confirm that these are in fact aftershocks exhibiting very similar waveforms to the main events. Many of the more marginal correlation detections are not made when the calculations are repeated using shorter signal segments, fewer sensors or more distant stations. We demonstrate in addition how these almost repeating seismic sources have been exploited to detect and measure timing anomalies at individual sites within the arrays and network. 相似文献
11.
12.
Pankaj M. Bhattacharya J. R. Kayal Saurabh Baruah S. S. Arefiev 《Pure and Applied Geophysics》2010,167(8-9):999-1012
We have imaged earthquake source zones beneath the northeast India region by seismic tomography, fractal dimension and b value mapping. 3D P-wave velocity (Vp) structure is imaged by the Local Earthquake Tomography (LET) method. High precision P-wave (3,494) and S-wave (3,064) travel times of 980 selected earthquakes, m d ≥ 2.5, are used. The events were recorded by 77 temporary/permanent seismic stations in the region during 1993–1999. By the LET method simultaneous inversion is made for precise location of the events as well as for 3D seismic imaging of the velocity structure. Fractal dimension and seismic b value has been estimated using the 980 LET relocated epicenters. A prominent northwest–southeast low Vp structure is imaged between the Shillong Plateau and Mikir hills; that reflects the Kopili fault. At the fault end, a high-Vp structure is imaged at a depth of 40 km; this is inferred to be the source zone for high seismic activity along this fault. A similar high Vp seismic source zone is imaged beneath the Shillong Plateau at 30 km depth. Both of the source zones have high fractal dimension, from 1.80 to 1.90, indicating that most of the earthquake associated fractures are approaching a 2D space. The spatial fractal dimension variation map has revealed the seismogenic structures and the crustal heterogeneities in the region. The seismic b value in northeast India is found to vary from 0.6 to 1.0. Higher b value contours are obtained along the Kopili fault (~1.0), and in the Shillong Plateau (~0.9) The correlation coefficient between the fractal dimension and b value is found to be 0.79, indicating that the correlation is positive and significant. To the south of Shillong Plateau, a low Vp structure is interpreted as thick (~20 km) sediments in the Bengal basin, with almost no seismic activity in the basin. 相似文献
13.
R. Carluccio A. Giuntini V. Materni S. Chiappini C. Bignami F. D’Ajello Caracciolo A. Pignatelli S. Stramondo R. Console M. Chiappini 《Pure and Applied Geophysics》2014,171(3-5):341-359
The Democratic People Republic of Korea announced two underground nuclear tests carried out in their territory respectively on October 9th, 2006 and May 25th, 2009. The scarce information on the precise location and the size of those explosions has stimulated various kinds of studies, mostly based on seismological observations, by several national agencies concerned with the Nuclear Test Ban Treaty verification. We analysed the available seismological data collected through a global high-quality network for the two tests. After picking up the arrival times at the various stations, a standard location program has been applied to the observed data. If we use all the available data for each single event, due to the different magnitude and different number of available stations, the locations appear quite different. On the contrary, if we use only the common stations, they happen to be only few km apart from each other and within their respective error ellipses. A more accurate relative location has been carried out by the application of algorithms such as double difference joint hypocenter determination (DDJHD) and waveform alignment. The epicentral distance between the two events obtained by these methods is 2 km, with the 2006 event shifted to the ESE with respect to that of 2009. We then used a dataset of VHR TerraSAR-X satellite images to detect possible surface effects of the underground tests. This is the first ever case where these highly performing SAR data have been used to such aim. We applied InSAR processing technique to fully exploit the capabilities of SAR data to measure very short displacements over large areas. Two interferograms have been computed, one co-event and one post-event, to remove possible residual topographic signals. A clear displacement pattern has been highlighted over a mountainous area within the investigated region, measuring a maximum displacement of about 45 mm overall the relief. Hypothesizing that the 2009 nuclear test had been carried out close to the area where the displacement has been observed through the DInSAR technique, its relation with the epicenter location obtained through seismological processing has been discussed as a possible alternative hypothesis with respect to the preferred solutions reported by the nuclear explosion database (NEDB). The distance of about 10 km between the two places can be considered acceptable in light of the possible systematic location shifts commonly observed in the seismological practice over a global scale. The difference between the m b magnitudes of the two tests could reflect differences in geological conditions of the two test sites, even if the yield of the two explosions had been the same. 相似文献
14.
We implement an infrasound semblance technique to identify acoustic sources originating from volcanic vents and apply the technique to the generally low-amplitude infrasound (< 3 Pa at 1 km) signals produced by Santiaguito dome in Guatemala. Semblance detection is demonstrated with data collected from two-element miniature arrays with ~ 30 m spacing between elements. The semblance technique is effective at identifying a range of eruptive phenomena, including pyroclastic-laden eruptions, vigorous degassing events, and rockfalls, even during periods of high wind contamination Many of the detected events are low in amplitude (tens of mPa) such that they are observed only by select arrays positioned with proximity and line-of-sight to the source. Larger events, such as the pyroclastic-laden eruptions, which occurred bi-hourly in 2009, were detected by all five arrays and produced an infrasonic signal that was correlated across the network. Network correlated events can be roughly located and map to the summit of the Caliente Vent where pyroclastic-laden eruptions originate. In general, the degree of Santiaguito infrasound event correlation is poor across the network, suggesting that complex source geometry contributes to asymmetric sound radiation. 相似文献
15.
Three large-scale on-surface explosions were conducted by the Geophysical Institute of Israel (GII) at the Sayarim Military Range, Negev desert, Israel: about 82 tons of strong high explosives in August 2009, and two explosions of about 10 and 100 tons of ANFO explosives in January 2011. It was a collaborative effort between Israel, CTBTO, USA and several European countries, with the main goal to provide fully controlled ground truth (GT0) infrasound sources, monitored by extensive observations, for calibration of International Monitoring System (IMS) infrasound stations in Europe, Middle East and Asia. In all shots, the explosives were assembled like a pyramid/hemisphere on dry desert alluvium, with a complicated explosion design, different from the ideal homogenous hemisphere used in similar experiments in the past. Strong boosters and an upward charge detonation scheme were applied to provide more energy radiated to the atmosphere. Under these conditions the evaluation of the actual explosion yield, an important source parameter, is crucial for the GT0 calibration experiment. Audio-visual, air-shock and acoustic records were utilized for interpretation of observed unique blast effects, and for determination of blast wave parameters suited for yield estimation and the associated relationships. High-pressure gauges were deployed at 100–600 m to record air-blast properties, evaluate the efficiency of the charge design and energy generation, and provide a reliable estimation of the charge yield. The yield estimators, based on empirical scaled relations for well-known basic air-blast parameters—the peak pressure, impulse and positive phase duration, as well as on the crater dimensions and seismic magnitudes, were analyzed. A novel empirical scaled relationship for the little-known secondary shock delay was developed, consistent for broad ranges of ANFO charges and distances, which facilitates using this stable and reliable air-blast parameter as a new potential yield estimator. The delay data of the 2009 shot with IMI explosives, characterized by much higher detonation velocity, are clearly separated from ANFO data, thus indicating a dependence on explosive type. This unique dual Sayarim explosion experiment (August 2009/January 2011), with the strongest GT0 sources since the establishment of the IMS network, clearly demonstrated the most favorable westward/eastward infrasound propagation up to 3,400/6,250 km according to appropriate summer/winter weather pattern and stratospheric wind directions, respectively, and thus verified empirically common models of infrasound propagation in the atmosphere. 相似文献
16.
The South Ural meteoroid (February 15, 2013; near the city of Chelyabinsk) is undoubtedly the best documented meteoroid in history. Its passage through the atmosphere has been recorded on videos and photographs, visually by observers, with ground-based infrasound microphones and seismographs, and by satellites in orbit. In this work, the results are presented of an analysis of the transionospheric GPS sounding data collected in the vicinity of the South Ural meteoroid site, which show a weak ionospheric effect. The ionospheric disturbances are found to be asymmetric about the explosion epicenter. The received signals are compared, both in shape and amplitude, with the reported ionospheric effects of ground level explosions with radio diagnostics. It is shown that the confident registration of ionospheric effects as acoustic gravity waves (AGWs) by means of vertical sounding and GPS technologies for ground explosions in the range of 0.26–0.6 kt casts doubt on the existing TNT equivalent estimates (up to 500 kt) for the Chelyabinsk event. The absence of effects in the magnetic field and in the ionosphere far zone at distances of 1500–2000 km from the superbolide explosion epicenter also raises a question about the possibility of an overestimated TNT equivalent. An alternative explanation is to consider the superposition of a cylindrical ballistic wave (due to the hypersonic motion of the meteoroid) with spherical shock waves caused by the multiple time points of fragmentation (multiple explosions) of the superbolide as a resulting source of the AGW impact on ionospheric layers. 相似文献
17.
M. Mesimeri V. Karakostas E. Papadimitriou D. Schaff G. Tsaklidis 《Journal of Seismology》2016,20(2):595-614
The 2013 Aigion earthquake swarm that took place in the west part of Corinth Gulf is investigated for revealing faulting and seismicity properties of the activated area. The activity started on May 21 and was appreciably intense in the next 3 months. The recordings of the Hellenic Unified Seismological Network (HUSN), which is adequately dense around the affected area, were used to accurately locate 1501 events. The double difference (hypoDD) technique was employed for the manually picked P and S phases along with differential times derived from waveform cross-correlation for improving location accuracy. The activated area with dimensions 6?×?2 km is located approximately 5 km SE of Aigion. Focal mechanisms of 77 events with M?≥?2.0 were determined from P wave first motions and used for the geometry identification of the ruptured segments. Spatio-temporal distribution of earthquakes revealed an eastward and westward hypocentral migration from the starting point suggesting the division of the seismic swarm into four major clusters. The hypocentral migration was corroborated by the Coulomb stress change calculation, indicating that four fault segments involved in the rupture process successively failed by stress change encouragement. Examination of fluid flow brought out that it cannot be unambiguously considered as the driving mechanism for the successive failures. 相似文献
18.
Changsheng Jiang Zhongliang Wu Yutong Li Tengfei Ma 《Pure and Applied Geophysics》2014,171(3-5):413-423
“Repeating earthquakes” identified by waveform cross-correlation, with inter-event separation of no more than 1 km, can be used for assessment of location precision. Assuming that the network-measured apparent inter-epicenter distance X of the “repeating doublets” indicates the location precision, we estimated the regionalized location quality of the China National Seismograph Network by comparing the “repeating events” in and around China by Schaff and Richards (Science 303: 1176–1178, 2004; J Geophys Res 116: B03309, 2011) and the monthly catalogue of the China Earthquake Networks Center. The comparison shows that the average X value of the China National Seismograph Network is approximately 10 km. The mis-location is larger for the Tibetan Plateau, west and north of Xinjiang, and east of Inner Mongolia, as indicated by larger X values. Mis-location is correlated with the completeness magnitude of the earthquake catalogue. Using the data from the Beijing Capital Circle Region, the dependence of the mis-location on the distribution of seismic stations can be further confirmed. 相似文献
19.
In summer 2003, a Chaparral Model 2 microphone was deployed at Shishaldin Volcano, Aleutian Islands, Alaska. The pressure
sensor was co-located with a short-period seismometer on the volcano’s north flank at a distance of 6.62 km from the active
summit vent. The seismo-acoustic data exhibit a correlation between impulsive acoustic signals (1–2 Pa) and long-period (LP,
1–2 Hz) earthquakes. Since it last erupted in 1999, Shishaldin has been characterized by sustained seismicity consisting of
many hundreds to two thousand LP events per day. The activity is accompanied by up to ∼200 m high discrete gas puffs exiting
the small summit vent, but no significant eruptive activity has been confirmed. The acoustic waveforms possess similarity
throughout the data set (July 2003–November 2004) indicating a repetitive source mechanism. The simplicity of the acoustic
waveforms, the impulsive onsets with relatively short (∼10–20 s) gradually decaying codas and the waveform similarities suggest
that the acoustic pulses are generated at the fluid–air interface within an open-vent system. SO2 measurements have revealed a low SO2 flux, suggesting a hydrothermal system with magmatic gases leaking through. This hypothesis is supported by the steady-state
nature of Shishaldin’s volcanic system since 1999. Time delays between the seismic LP and infrasound onsets were acquired
from a representative day of seismo-acoustic data. A simple model was used to estimate source depths. The short seismo-acoustic
delay times have revealed that the seismic and acoustic sources are co-located at a depth of 240±200 m below the crater rim.
This shallow depth is confirmed by resonance of the upper portion of the open conduit, which produces standing waves with
f=0.3 Hz in the acoustic waveform codas. The infrasound data has allowed us to relate Shishaldin’s LP earthquakes to degassing
explosions, created by gas volume ruptures from a fluid–air interface. 相似文献
20.
The study of infrasound is experiencing a renaissance in recent years since it was chosen as a verification technique for
the Comprehensive Nuclear-Test-Ban Treaty. Currently, 60 infrasound arrays are being installed to monitor the atmosphere for
nuclear tests as part of the International Monitoring System (IMS). The number of non-IMS arrays also increases worldwide.
The experimental ARCES infrasound array (ARCI) is an example of such an initiative. The detectability of infrasound differs
for each array and is a function of the array location and configuration, the state of the atmosphere, and the presence of
natural and anthropogenic sources. In this study, a year of infrasound data is analyzed as recorded by ARCI. Contributions
of the atmosphere and the sources are evaluated in both a low- (0.1–1.0 Hz) and high-frequency (1.0–7.0 Hz) pass-band. The
enormous number of detections in the low-frequency band is explained in terms of the stratospheric wind and ocean wave activity
and compared with the detection of microseism. Understanding the detectability in the low-frequency band is of utmost importance
for successfully applying infrasound as a verification technique since small-sized nuclear test will show up in this frequency
range. 相似文献