共查询到20条相似文献，搜索用时 15 毫秒
1.
Vibroseis is a source used commonly for inland seismic exploration. This non-destructive source is often used in urban areas with strong environmental noise. The main goal of seismic data processing is to increase the signal/noise ratio where a determinant step is deconvolution. Vibroseis seismic data do not meet the basic minimum-phase assumption for the application of spiking and predictive deconvolution, therefore various techniques, such as phase shift, are applied to the data, to be able to successfully perform deconvolution of vibroseis data.This work analyzes the application of deconvolution techniques before and after cross-correlation on a real data set acquired for high resolution prospection of deep aquifers. In particular, we compare pre-correlation spiking and predictive deconvolution with Wiener filtering and with post-correlation time variant spectral whitening deconvolution. The main result is that at small offsets, post cross-correlation spectral whitening deconvolution and pre-correlation spiking deconvolution yield comparable results, while for large offsets the best result is obtained by applying a pre-cross-correlation predictive deconvolution. 相似文献
2.
—Seismic data processing mostly takes into account the statistics inherent in the data to improve the data quality. Since some years the deterministic approach for processing shows many advantages. This approach takes into account e.g., the source signature, with the knowledge of its amplitude and phase behavior. The transformation of the signal into an optimized form is called wavelet processing. By this step an optimal input for deconvolution can be produced, which needs a minimum- delay signal to function well. The interpreter needs a signal which gives the optimum resolution, which is accomplished by the zero-phase transformation of the input signal. The combination of different input sources such as Vibroseis and Dynamite requires a phase adoption. All these procedures can be implemented via Two-Sided-Recursive (TSR-) filters. Spectral balancing can be accomplished very effectively in time domain after a minimum delay transform of the input signals. The DEKORP data suffer from a low signal/noise ratio, so that special methods for the suppression of coherent noise trains were developed. This can be done by subtractive coherency filtering. Multiple seismic reflections also can be suppressed by this method very effectively. All processing procedures developed during recent years are now fully integrated in commercial software operated by the processing center in Clausthal. 相似文献
3.
Derman Dondurur 《Pure and Applied Geophysics》2010,167(10):1233-1245
Wiener deconvolution is generally used to improve resolution of the seismic sections, although it has several important assumptions. I propose a new method named Gold deconvolution to obtain Earth’s sparse-spike reflectivity series. The method uses a recursive approach and requires the source waveform to be known, which is termed as Deterministic Gold deconvolution. In the case of the unknown wavelet, it is estimated from seismic data and the process is then termed as Statistical Gold deconvolution. In addition to the minimum phase, Gold deconvolution method also works for zero and mixed phase wavelets even on the noisy seismic data. The proposed method makes no assumption on the phase of the input wavelet, however, it needs the following assumptions to produce satisfactory results: (1) source waveform is known, if not, it should be estimated from seismic data, (2) source wavelet is stationary at least within a specified time gate, (3) input seismic data is zero offset and does not contain multiples, and (4) Earth consists of sparse spike reflectivity series. When applied in small time and space windows, the Gold deconvolution algorithm overcomes nonstationarity of the input wavelet. The algorithm uses several thousands of iterations, and generally a higher number of iterations produces better results. Since the wavelet is extracted from the seismogram itself for the Statistical Gold deconvolution case, the Gold deconvolution algorithm should be applied via constant-length windows both in time and space directions to overcome the nonstationarity of the wavelet in the input seismograms. The method can be extended into a two-dimensional case to obtain time-and-space dependent reflectivity, although I use one-dimensional Gold deconvolution in a trace-by-trace basis. The method is effective in areas where small-scale bright spots exist and it can also be used to locate thin reservoirs. Since the method produces better results for the Deterministic Gold deconvolution case, it can be used for the deterministic deconvolution of the data sets with known source waveforms such as land Vibroseis records and marine CHIRP systems. 相似文献
4.
We propose a three‐step bandwidth enhancing wavelet deconvolution process, combining linear inverse filtering and non‐linear reflectivity construction based on a sparseness assumption. The first step is conventional Wiener deconvolution. The second step consists of further spectral whitening outside the spectral bandwidth of the residual wavelet after Wiener deconvolution, i.e., the wavelet resulting from application of the Wiener deconvolution filter to the original wavelet, which usually is not a perfect spike due to band limitations of the original wavelet. We specifically propose a zero‐phase filtered sparse‐spike deconvolution as the second step to recover the reflectivity dominantly outside of the bandwidth of the residual wavelet after Wiener deconvolution. The filter applied to the sparse‐spike deconvolution result is proportional to the deviation of the amplitude spectrum of the residual wavelet from unity, i.e., it is of higher amplitude; the closer the amplitude spectrum of the residual wavelet is to zero, but of very low amplitude, the closer it is to unity. The third step consists of summation of the data from the two first steps, basically adding gradually the contribution from the sparse‐spike deconvolution result at those frequencies at which the residual wavelet after Wiener deconvolution has small amplitudes. We propose to call this technique “sparsity‐enhanced wavelet deconvolution”. We demonstrate the technique on real data with the deconvolution of the (normal‐incidence) source side sea‐surface ghost of marine towed streamer data. We also present the extension of the proposed technique to time‐varying wavelet deconvolution. 相似文献
5.
针对高阶统计量混合相位地震子波提取方法的局限性, 提出一种基于矢量预测的单输入多输出系统(SIMO)的混合相位地震子波提取方法. 该方法利用二阶循环平稳统计量包含的系统相位信息, 将CMP道集视为一个单输入多输出系统的输出, 利用道集中相邻两道或多道数据通过矢量预测来构建反子波计算的方程式, 进一步进行混合相位子波提取. 利用提取出的子波相位信息对CMP道集进行纯相位滤波, 能够替代相位校正技术, 并且利用获取的反褶积算子对CMP道集进行反褶积处理, 使提高分辨率后的不同道子波振幅、 频率、 波形相一致, 提高叠加的质量. 模型试算和实际资料处理结果表明, 文中方法适用于任意相位的子波提取及反褶积处理, 且处理精度较高, 具有较高的实际应用价值. 相似文献
6.
B. BUTTKUS 《Geophysical Prospecting》1975,23(4):712-748
The application of homomorphic filtering in marine seismic reflection work is investigated with the aims to achieve the estimation of the basic wavelet, the wavelet deconvolution and the elimination of multiples. Each of these deconvolution problems can be subdivided into two parts: The first problem is the detection of those parts in the cepstrum which ought to be suppressed in processing. The second part includes the actual filtering process and the problem of minimizing the random noise which generally is enhanced during the homomorphic procedure. The application of homomorphic filters to synthetic seismograms and air-gun measurements shows the possibilities for the practical application of the method as well as the critical parameters which determine the quality of the results. These parameters are:
- a) the signal-to-noise ratio (SNR) of the input data
- b) the window width and the cepstrum components for the separation of the individual parts
- c) the time invariance of the signal in the trace.
7.
S. M. DEREGOWSKI 《Geophysical Prospecting》1978,26(1):252-290
In a previous paper the author showed how, by computing an inverse filter in the frequency domain, an automatic compromise could be made between the conflicting requirements to spike a wavelet and to keep the attendant noise amplification within bounds. This paper extends the technique to take account of errors in the estimated shape of the wavelet defined to the deconvolution process. The drastic effects which such errors can have if they are ignored are demonstrated. A novel form of filter–called the “self-matching filter”–is defined which allows the user to limit not only the noise amplification but also the sensitivity of the filter to random uncertainties in the estimated wavelet. This is achieved by whitening the spectrum only within automatically selected pass bands whilst suppressing other noise-dominated or uncertainly defined frequency components. Conventional Wiener filtering is shown to be a special case of this more general filter, namely one in which the wavelet uncertainty is completely ignored. The type of phase spectrum which the output pulse should be designed to possess (e.g. zero phase or minimum phase) is briefly discussed. 相似文献
8.
9.
Deconvolution is an essential step for high-resolution imaging in seismic data processing. The frequency and phase of the seismic wavelet change through time during wave propagation as a consequence of seismic absorption. Therefore, wavelet estimation is the most vital step of deconvolution, which plays the main role in seismic processing and inversion. Gabor deconvolution is an effective method to eliminate attenuation effects. Since Gabor transform does not prepare the information about the phase, minimum-phase assumption is usually supposed to estimate the phase of the wavelet. This manner does not return the optimum response where the source wavelet would be dominantly a mixed phase. We used the kurtosis maximization algorithm to estimate the phase of the wavelet. First, we removed the attenuation effect in the Gabor domain and computed the amplitude spectrum of the source wavelet; then, we rotated the seismic trace with a constant phase to reach the maximum kurtosis. This procedure was repeated in moving windows to obtain the time-varying phase changes. After that, the propagating wavelet was generated to solve the inversion problem of the convolutional model. We showed that the assumption of minimum phase does not reflect a suitable response in the case of mixed-phase wavelets. Application of this algorithm on synthetic and real data shows that subtle reflectivity information could be recovered and vertical seismic resolution is significantly improved. 相似文献
10.
Vibroseis deconvolution can be performed either before or after correlation. As regards the deconvolution before correlation, the Vibroseis deconvolution operator can be described as convolution of a spike deconvolution operator with a minimum-phase filter operator with bandpass properties. As regards the deconvolution after correlation, the deconvolution operator can be shown to be the convolution of three operators: spike deconvolution operator and two-fold convolution with a minimum phase operator. Time-varying Vibroseis deconvolution can particularly well be described and performed after correlation. 相似文献
11.
12.
A. N. BOWEN 《Geophysical Prospecting》1986,34(3):366-382
Wiener ‘spiking’ deconvolution of seismic traces in the absence of a known source wavelet relies upon the use of digital filters, which are optimum in a least-squares error sense only if the wavelet to be deconvolved is minimum phase. In the marine environment in particular this condition is frequently violated, since bubble pulse oscillations result in source signatures which deviate significantly from minimum phase. The degree to which the deconvolution is impaired by such violation is generally difficult to assess, since without a measured source signature there is no optimally deconvolved trace with which the spiked trace may be compared. A recently developed near-bottom seismic profiler used in conjunction with a surface air gun source produces traces which contain the far-field source signature as the first arrival. Knowledge of this characteristic wavelet permits the design of two-sided Wiener spiking and shaping filters which can be used to accurately deconvolve the remainder of the trace. In this paper the performance of such optimum-lag filters is compared with that of the zero-lag (one-sided) operators which can be evaluated from the reflected arrival sequence alone by assuming a minimum phase source wavelet. Results indicate that the use of zero-lag operators on traces containing non-minimum phase wavelets introduces significant quantities of noise energy into the seismic record. Signal to noise ratios may however be preserved or even increased during deconvolution by the use of optimum-lag spiking or shaping filters. A debubbling technique involving matched filtering of the trace with the source wavelet followed by optimum-lag Wiener deconvolution did not give a higher quality result than can be obtained simply by the application of a suitably chosen Wiener shaping filter. However, cross correlation of an optimum-lag spike filtered trace with the known ‘actual output’ of the filter when presented with the source signature is found to enhance signal-to-noise ratio whilst maintaining improved resolution. 相似文献
13.
C. Schmelzbach F. ScherbaumJ. Tronicke P. Dietrich 《Journal of Applied Geophysics》2011,75(4):615-630
Enhancing the resolution and accuracy of surface ground-penetrating radar (GPR) reflection data by inverse filtering to recover a zero-phased band-limited reflectivity image requires a deconvolution technique that takes the mixed-phase character of the embedded wavelet into account. In contrast, standard stochastic deconvolution techniques assume that the wavelet is minimum phase and, hence, often meet with limited success when applied to GPR data. We present a new general-purpose blind deconvolution algorithm for mixed-phase wavelet estimation and deconvolution that (1) uses the parametrization of a mixed-phase wavelet as the convolution of the wavelet's minimum-phase equivalent with a dispersive all-pass filter, (2) includes prior information about the wavelet to be estimated in a Bayesian framework, and (3) relies on the assumption of a sparse reflectivity. Solving the normal equations using the data autocorrelation function provides an inverse filter that optimally removes the minimum-phase equivalent of the wavelet from the data, which leaves traces with a balanced amplitude spectrum but distorted phase. To compensate for the remaining phase errors, we invert in the frequency domain for an all-pass filter thereby taking advantage of the fact that the action of the all-pass filter is exclusively contained in its phase spectrum. A key element of our algorithm and a novelty in blind deconvolution is the inclusion of prior information that allows resolving ambiguities in polarity and timing that cannot be resolved using the sparseness measure alone. We employ a global inversion approach for non-linear optimization to find the all-pass filter phase values for each signal frequency. We tested the robustness and reliability of our algorithm on synthetic data with different wavelets, 1-D reflectivity models of different complexity, varying levels of added noise, and different types of prior information. When applied to realistic synthetic 2-D data and 2-D field data, we obtain images with increased temporal resolution compared to the results of standard processing. 相似文献
14.
基于保角变换的双谱域相位谱估计方法及其在地震子波估计中的应用(英文) 总被引：2，自引：0，他引：2
地震子波估计是地震资料处理与解释中的重要环节,它的准确与否直接关系到反褶积及反演等结果的好坏。高阶谱(双谱和三谱)地震子波估计方法是一类重要的、新兴的子波估计方法,然而基于高阶谱的地震子波估计往往因为高阶相位谱卷绕的原因,导致子波相位谱求解产生偏差,进而影响了混合相位子波估计的效果。针对这一问题,本文在双谱域提出了一种基于保角变换的相位谱求解方法。通过缩小傅里叶相位谱的取值范围,有效避免了双谱相位发生卷绕的情况,从而消除了原相位谱估计中双谱相位卷绕的影响。该方法与最小二乘法相位谱估计相结合,构成了基于保角变换的最小二乘地震子波相位谱估计方法,并与最小二乘地震子波振幅谱估计方法一起,应用到了地震资料混合相位子波估计中。理论模型和实际资料验证了该方法的有效性。同时本文将双谱域地震子波相位谱估计中保角变换的思想推广到三谱域地震子波相位谱估计中。 相似文献
15.
Bussgang算法是针对褶积盲源分离问题提出的,本文将其用于地震盲反褶积处理.由于广义高斯概率密度函数具有逼近任意概率密度函数的能力,从反射系数序列的统计特征出发,引入广义高斯分布来体现反射系数序列超高斯分布特征.依据反射系数序列的统计特征和Bussgang算法原理,建立以Kullback-Leibler距离为非高斯性度量的目标函数,并导出算法中涉及到的无记忆非线性函数,最终实现了地震盲反褶积.模型试算和实际资料处理结果表明,该方法能较好地适应非最小相位系统,能够同时实现地震子波和反射系数估计,有效地提高地震资料分辨率. 相似文献
16.
R.-G. FERBER 《Geophysical Prospecting》1985,33(2):212-223
A main problem in computing reflection coefficients from seismograms is the instability of the inversion procedure due to noise. This problem is attacked for two well-known inversion schemes for normal-incidence reflection seismograms. The crustal model consists of a stack of elastic, laterally homogeneous layers between two elastic half-spaces. The first method, which directly computes the reflection coefficients from the seismogram is called “Dynamic Deconvolution”. The second method, here called “Inversion Filtering”, is a two-stage procedure. The first stage is the construction of a causal filter by factorization of the spectral function via Levinson-recursion. Filtering the seismogram is the second stage. The filtered seismogram is a good approximation for the reflection coefficients sequence (unless the coefficients are too large). In the non-linear terms of dynamic deconvolution and Levinson-recursion the noise could play havoc with the computation. In order to stabilize the algorithms, the bias of these terms is estimated and removed. Additionally incorporated is a statistical test for the reflection coefficients in dynamic deconvolution and the partial correlation coefficients in Levinson-recursion, which are set to zero if they are not significantly different from noise. The result of stabilization is demonstrated on synthetic seismograms. For unit spike source pulse and white noise, dynamic deconvolution outperforms inversion filtering due to its exact nature and lesser computational burden. On the other hand, especially in the more realistic bandlimited case, inversion filtering has the great advantage that the second stage acts linearly on the seismogram, which allows the calculation of the effect of the inversion procedure on the wavelet shape and the noise spectrum. 相似文献
17.
地震子波估计是地震资料处理和解释中的一个关键问题,子波估计的可靠性会直接影响反褶积和反演的准确度.现有的子波估计方法分为确定型和统计型两种类型,本文通过结合这两类方法,利用确定型的谱分析法和统计型的偏度最大化方法,分别提取时变子波的振幅和相位信息,得到估计的时变子波.这种方法不需要对子波进行任何时不变或相位等的假设,具有对时变相位的估计能力.进而利用估计时变子波进行非稳态反褶积,提高地震记录的保真度,为精细储层预测和描述提供高质量的剖面.理论模型试算验证了方法的可行性,通过实际地震资料的处理应用,表明该方法能有效地提取出子波时变信息. 相似文献
18.
Klauder wavelet removal before vibroseis deconvolution 总被引：1，自引：0，他引：1
The spiking deconvolution of a field seismic trace requires that the seismic wavelet on the trace be minimum phase. On a dynamite trace, the component wavelets due to the effects of recording instruments, coupling, attenuation, ghosts, reverberations and other types of multiple reflection are minimum phase. The seismic wavelet is the convolution of the component wavelets. As a result, the seismic wavelet on a dynamite trace is minimum phase and thus can be removed by spiking deconvolution. However, on a correlated vibroseis trace, the seismic wavelet is the convolution of the zero-phase Klauder wavelet with the component minimum-phase wavelets. Thus the seismic wavelet occurring on a correlated vibroseis trace does not meet the minimum-phase requirement necessary for spiking deconvolution, and the final result of deconvolution is less than optimal. Over the years, this problem has been investigated and various methods of correction have been introduced. In essence, the existing methods of vibroseis deconvolution make use of a correction that converts (on the correlated trace) the Klauder wavelet into its minimum-phase counterpart. The seismic wavelet, which is the convolution of the minimum-phase counterpart with the component minimum-phase wavelets, is then removed by spiking deconvolution. This means that spiking deconvolution removes both the constructed minimum-phase Klauder counterpart and the component minimum-phase wavelets. Here, a new method is proposed: instead of being converted to minimum phase, the Klauder wavelet is removed directly. The spiking deconvolution can then proceed unimpeded as in the case of a dynamite record. These results also hold for gap predictive deconvolution because gap deconvolution is a special case of spiking deconvolution in which the deconvolved trace is smoothed by the front part of the minimum-phase wavelet that was removed. 相似文献
19.
In certain areas continuous Vibroseis profiling is not possible due to varying terrain conditions. Impulsive sources can be used to maintain continuous coverage. While this technique keeps the coverage at the desired level, for the processing of the actual data there is the problem of using different sources resulting in different source wavelets. In addition, the effect of the free surface is different for these two energy sources. The approach to these problems consists of a minimum-phase transformation of the two-sided Vibroseis data by removal of the anticipation component of the autocorrelation of the filtered sweep and a minimum-phase transformation of the impulsive source data by replacement of the recording filter operator with its minimum-phase correspondent. Therefore, after this transformation, both datasets show causal wavelets and a conventional deconvolution (spike or predictive) may be used. After stacking, a zero-phase transformation can be performed resulting in traces well suited for computing pseudo-acoustic impedance logs or for application of complex seismic trace analysis. The solution is also applicable to pure Vibroseis data, thereby eliminating the need for a special Vibroseis deconvolution. The processing steps described above are demonstrated on synthetic and actual data. The transformation operators used are two-sided recursive (TSR) shaping filters. After application of the above adjustment procedure, remaining signal distortions can be removed by modifying only the phase spectrum or both the amplitude and phase spectra. It can be shown that an arbitrary distortion defined in the frequency domain, i.e., a distortion of the amplitude and phase spectrum, is noticeable in the time section as a two-sided signal. 相似文献
20.
The purpose of deconvolution is to retrieve the reflectivity from seismic data. To do this requires an estimate of the seismic wavelet, which in some techniques is estimated simultaneously with the reflectivity, and in others is assumed known. The most popular deconvolution technique is inverse filtering. It has the property that the deconvolved reflectivity is band-limited. Band-limitation implies that reflectors are not sharply resolved, which can lead to serious interpretation problems in detailed delineation. To overcome the adverse effects of band-limitation, various alternatives for inverse filtering have been proposed. One class of alternatives is Lp-norm deconvolution, L1norm deconvolution being the best-known of this class. We show that for an exact convolutional forward model and statistically independent reflectivity and additive noise, the maximum likelihood estimate of the reflectivity can be obtained by Lp-norm deconvolution for a range of multivariate probability density functions of the reflectivity and the noise. The L∞-norm corresponds to a uniform distribution, the L2-norm to a Gaussian distribution, the L1-norm to an exponential distribution and the L0-norm to a variable that is sparsely distributed. For instance, if we assume sparse and spiky reflectivity and Gaussian noise with zero mean, the Lp-norm deconvolution problem is solved best by minimizing the L0-norm of the reflectivity and the L2-norm of the noise. However, the L0-norm is difficult to implement in an algorithm. From a practical point of view, the frequency-domain mixed-norm method that minimizes the L1norm of the reflectivity and the L2-norm of the noise is the best alternative. Lp-norm deconvolution can be stated in both time and frequency-domain. We show that both approaches are only equivalent for the case when the noise is minimized with the L2-norm. Finally, some Lp-norm deconvolution methods are compared on synthetic and field data. For the practical examples, the wide range of possible Lp-norm deconvolution methods is narrowed down to three methods with p= 1 and/or 2. Given the assumptions of sparsely distributed reflectivity and Gaussian noise, we conclude that the mixed L1norm (reflectivity) L2-norm (noise) performs best. However, the problems inherent to single-trace deconvolution techniques, for example the problem of generating spurious events, remain. For practical application, a greater problem is that only the main, well-separated events are properly resolved. 相似文献