首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Results for more than 42 months of observations with the superconducting gravimeter CD-034 at the Geodynamic Observatory Moxa are discussed. Moxa observatory is one of the newer stations within the ‘Global Geodynamics Project’ (GGP). A special feature of the gravimeter at Moxa is its dual sensor system; differences in the results obtained from the two sensor recordings are generally well within the standard deviations of the tidal analysis. One significant difference concerns the slightly different drift rates of 31 and 49.5 nm/s2 per year for upper and lower sensor; both sensor drifts can be fitted by a linear function. We find that the noise levels are close to the ‘New Low Noise Model’ for the seismic-modes and are also low in the tidal bands. Due to this low noise, Moxa is a station well suited to search for small geodynamic signals. The long-period variation in the gravity residuals correlates well with the polar motion.The difference signal between the two sensor recordings has a peak-to-peak amplitude of about 6 nm/s2 and shows systematic variations. Its spectrum is characterised by instrumental noise between 0.2 and 0.4 cph. The noise level of the difference and of the sum of the two residual datasets are clearly lower, respectively, higher than the noise contents of the gravity residuals themselves. This is a strong indication for the existence of broadband signals common to the two residual datasets, leading to the conjecture that the reduction of environmental effects is still not sufficient.Our results once more emphasize the necessity to correct the data for barometric pressure effects when analyzing the data for seismic modes. The reduction visibly increases the signal-to-noise ratio in the low frequencies of the mode band and helps to avoid misinterpreations of peaks. Besides the well known barometric pressure influence we can establish hydrological effects in the data which are probably caused by soil moisture and groundwater table variations as well as by batch-wise water movement within the weathering layer. As the major part of the observatory surroundings is above gravimeter level, an anticorrelation between hydrological and gravity changes is observed. In addition, it can be shown that global hydrological effects reach an order of magnitude that makes it necessary to consider these effects when analyzing long-period signals like polar motion. Vice versa these effects are large enough to be detectable in the gravity data. A first joint analysis of five datasets from the GGP network shows no indications for signals related to the Slichter triplet or core modes.  相似文献   

2.
In recent years, several claims of detection of weak harmonic signals in the sub-tidal band of frequencies of high-quality gravimeter data have been made. Here, we review our attempts at confirming Smylie's claim of detection of the Slichter mode of inner-core oscillation using the same four data sets he and his colleagues used. We further examine the homogeneous 2 year data sets obtained from the superconducting gravimeters sited in Strasbourg and at Cantley, Quebec. We show that the power spectra of tidal-reduced, pressure and slew-corrected gravity residuals from these data are indistinguishable from a random walk process except in narrow bands dominated by residual earth tides and by harmonics of the diurnal thermal-atmospheric tide. Such a random ‘brown’ residual could result from mechanical instabilities and electronic noise in the instruments themselves, from site-specific tectonic noise, from local hydrological variations and pier instabilities or it could derive from unaccounted for variability in the atmospheric pressure in the vicinity of the instruments. We argue that the homogeneous 2 year data sets show no evidence whatever of Slichter harmonics even though our preprocessing methods reduce ‘apparent noise levels’ in the core-mode band by almost an order magnitude in comparison with the four data sets originally employed by Smylie et al. and, in their first attempted confirmation of his claimed discovery, by Jensen et al.  相似文献   

3.
Not all of the gravity signals commonly observed in records of superconducting gravimeters have a physically significant meaning. Instrumental noise or signal components generated by specific processing techniques can have a strong effect. This paper analyzes selected case studies from gravity data acquired during the first period of GGP and tries to give an answer to the question of which signals are significant. It is focused on small amplitude variations in the time domain, which are compared with those of conventional spring-type gravimeters. Coherent atmospheric gravity signals due to atmospheric processes associated with strong vertical convection could be observed by different sensors. The second part deals with temporal variations of main tidal parameters, which can be seen clearly in the tidal analysis results from SG data. Synthetic case studies show that they are not strongly influenced by the analysis procedure and therefore mainly reflect ocean loading processes.  相似文献   

4.
The signal to noise ratio in tidal data in the diurnal and semidiurnal frequency bands is ordinarily so large that the noise contribution to the tidal harmonic constants is unimportant. However, as the observational locations are selected progressively closer to an amphidrome (point of no tide), the signal to noise ratio decreases, making the tidal harmonic constants less dependable. Standard deviations in amplitude of M2 and S2 obtained from 12 29-day analyses of a year of tide data obtained at a standard tide station, estimated to be 280 and 550 km away from the amphidromes for these constituents in the eastern Caribbean, are roughly one-third of the mean amplitudes for these constituents; the standard deviations in epoch are 38° and 30° respectively. Therefore, a program to locate an amphidrome precisely is self-defeating and the location can only be approximated by a grid of tide observations spanning the geographic position and/or by longer series of observations, using higher resolution to increase the signal to noise ratio. Amplitudes of 0.64 cm and 1.24 cm were calculated for M2 and S2 from a one-month series of pelagic observations obtained very close to an inferred position of the M2 amphidrome in the northeast Caribbean Sea.Abbreviations C&GS Coast and Geodetic Survey - CICAR Cooperative Investigation of the Caribbean and Adjacent Regions - IAPSO International Association for the Physical Sciences of the Ocean - ICOT Institute of Coastal Oceanography and Tides - IDOE International Decade of Ocean Exploration - NOAA National Oceanic and Atmospheric Administration - NOS National Ocean Survey - NSF National Science Foundation - SCOR Scientific Committee of Oceanic Research - UNESCO United Nations Educational, Scientific, and Cultural Organization  相似文献   

5.
Standard temperature and pressure sensors on Aanderaa RCM8 current meters have a resolution of 0.024 °C and 0.6 bar, each equal to 1 digital number (value) over a range of 1024. It is shown that an 11-month deep-ocean temperature record using only four values can contain useful spectral information on internal wave motions. This is partially due to the modulation of high-frequency data by non-zero low-frequency (subinertial) variations. This result follows from the comparison of this record with artificial three- and four-value data constructed from temperature records observed in stronger stratified waters nearby. These artificial records show main features of the internal wave band similar to those observed in the original data spectra. Peaks at tidal harmonic frequencies and enhancements at sum-tidal-inertial interaction frequencies are preserved in the artificial data, but overall noise level (and thus the continuum spectral slope) is enhanced with respect to the properly resolved records (using 15 and 100 values). As a demonstration of the stable accuracy of the temperature sensors, the poorly resolved records provided an estimate of mean stratification to within 5% of the estimate using Seabird CTD data.Responsible Editor: Hans Burchard  相似文献   

6.
Tidal current and elevation data were collected from five oceanographic moorings during October 2004 in Torres Strait, northern Australia, to assess the effects of large bedforms (i.e., sand banks) on the drag coefficient (CD) used for estimating bed shear stress in complex shallow shelf environments. Ten minute averages of tidal current speed and elevation data were collected for 18 days at an on-bank site (<7 m water depth) and an off-bank site (<10 m). These data were compared to data collected simultaneously from two shelf locations (<11 m) occupied to measure regional tidal behaviour. Overall CD estimates at the on- and off-bank sites attained 7.0±0.1×10−3 and 6.6±0.1×10−3, respectively. On-bank CD estimates also differed between the predominant east–west tidal streams, with easterly directed flows experiencing CD=7.8±0.18×10−3 and westerly directed flows CD=6.4±0.12×10−3. Statistically significant differences between the off-bank and on-bank sites are attributed to the large form drag exerted by the sand banks on the regional tidal currents, and statistically significant differences between the westward and eastward flows is ascribed to bedform asymmetry. Form drag from the large bedforms in Torres Strait comprises up to 65% of the total drag coefficient. When constructing sediment transport models, different CD estimates must therefore be applied to shelf regions containing steep bedforms compared to regions that do not. Our results extend the limited inventory of seabed drag coefficients for shallow shelf environments, and can be used to improve existing regional seabed mobilisation models, which have direct application to environmental management in Torres Strait.  相似文献   

7.
噪声水平上的爆炸余震信号提取   总被引：2，自引：0，他引：2  
文中采用窄带滤波、傅里叶反变换及小波分析在噪声水平上提取弱余震信号。窄带滤波能够在背景噪声水平上以及（－10）－（20）dB记录中提取有用信息，但是往往产生截断误差，如果数字序列具有较大的初始幅值，所提取的波形在截断处发生畸变。傅氏反变换从负信噪比的记录中提取的信号质量较差，伴有高频干扰成分，对于信噪比为正数的记录，傅氏反变换提取的波形是良好的，该种方法同滤波方法一样，也存在截断误差。小波分析从信噪比为负数的记录中提取的信号不理想，而从信噪比为正数的记录中提取的信号质量最好，波形完整，首尾清晰，基线平直，无截断误差。窄带滤波，傅氏反变换及小波分析有两个共同点，基一，都能够从强背景噪声中提取有用信息；其二，信噪比越大，获取的信号质量越高。  相似文献   

8.
The German Wadden Sea (southern North Sea) sediments are composed of both cohesive and non-cohesive deposits. The spatial distribution patterns are mainly driven by wind-induced waves and tidal currents. Transport intensity and duration depend on the hydrodynamic conditions, which vary over time. In this paper, the transport of suspended sediment was investigated on seasonal, tidal and hourly time scales in the back-barrier system of Spiekeroog Island. Long- and short-term data of fair weather periods and two storm events were investigated based on stationary and mobile measurements of currents and waves by Acoustic Doppler Current Profiler (ADCP), in situ particle size and suspended sediment concentration (SSC) measurements by laser in situ scattering and transmissometry (LISST) as well as wind records. The ADCP backscatter intensities were calibrated by means of LISST volume concentration data in order to quantify longer term SSCs and fluxes in the back-barrier system. Values up to 120 mg l−1 were recorded, but concentrations more commonly were below 60 mg l−1. The long-term results confirm former observations of a balanced budget during low-energy (fair weather) conditions in the study area. In general, SSCs were higher during spring tides than during neap tides. The data also clearly show the remobilisation of sediment by tidal current entrainment. The records include two severe storm events, “Britta” (1st November 2006) and “Kyrill” (18th January 2007). The data reveal very complex temporal flow and transport patterns. During both storm events, the export of material was mainly controlled by the interaction of wind, waves and tidal phase. The typical ebb-dominance occurring during fair-weather conditions was temporarily neutralised and even reversed to a flood-dominated situation. During “Kyrill”, the wind and high-waves setup in conjunction with the tidal phase was even able to compress the duration of two successive ebb cycles by over 70%. Although SSCs increased during both storms and higher turbulence lifted particle clouds upwards, an export of suspended matter towards the North Sea was only observed under the conditions taking place during “Britta”. Such fluxes, however, are currently still difficult to quantify because the backscatter intensity during high energy events includes a substantial amount of noise produced by the high turbulence, especially near the water surface.  相似文献   

9.
Phytoplankton biomass and primary production were monitored in the Hauraki Gulf and on the northeastern continental shelf, New Zealand - using ship surveys, moored instruments and satellite observations (1998-2001) - capturing variability across a range of space and time scales. A depth-integrated primary production model (DIM) was used to predict integrated productivity from surface parameters, enabling regional-specific estimates from satellite data. The shelf site was dominated by pico-phytoplankton, with low chlorophyll-a (<1 mg m−3) and annual production (136 g C m−2 yr−1). In contrast, the gulf contained a micro/nano-phytoplankton-dominated community, with relatively high chlorophyll-a (>1 mg m−3) and annual production (178 g C m−2 yr−1). Biomass and productivity responded to physico-chemical factors; a combination of light, critical mixing depths and/or nutrient limitation—particularly new nitrate-N. Relatively low biomass and production was observed during 1999. This coincided with inter-annual variability in the timing and extent of upwelling- and downwelling-favourable along-shelf wind-stress, influencing the fluxes of new nitrate-N to the shelf and gulf. Relationships with the Southern Oscillation Index are also discussed. Our multi-scaled sampling highlighted details associated with stratification and de-stratification events, and deep sub-surface chlorophyll-a not visible to satellite sensors. This study demonstrates the importance of multi-scaled sampling in gaining estimates of regional production and its responses to physico-chemical forcing.  相似文献   

10.
Observations are presented of currents, hydrography and turbulence in a jet-type tidally forced fjord in Svalbard. The fjord was ice covered at the time of the experiment in early spring 2004. Turbulence measurements were conducted by both moored instruments within the uppermost 5 m below the ice and a microstructure profiler covering 3–60 m at 75 m depth. Tidal choking at the mouth of the fjord induces a tidal jet advecting relatively warmer water past the measurement site and dominating the variability in hydrography. While there was no strong correlation with the observed hydrography or mixing and the phase of the semidiurnal tidal cycle, the mean structure in dissipation of turbulent kinetic energy, work done under the ice and the mixing in the water column correlated with the current when conditionally sampled for tidal jet events. Observed levels of dissipation of turbulent kinetic energy per unit mass, 1.1×10−7 W kg−1, and eddy diffusivity, 7.3×10−4 m2 s−1, were comparable to direct measurements at other coastal sites and shelves with rough topography and strong forcing. During spring tides, an average upward heat flux of 5 W m−2 in the under-ice boundary layer was observed. Instantaneous (1 h averaged) large heat flux events were correlated with periods of large inflow, hence elevated heat fluxes were associated with the tidal jet and its heat content. Vertical heat fluxes are derived from shear-probe measurements by employing a novel model for eddy diffusivity [Shih et al., 2005. Parameterization of turbulent fluxes and scales using homogeneous sheared stably stratified turbulence simulations. Journal of Fluid Mechanics 525, 193–214]. When compared to the direct heat flux measurements using the eddy correlation method at 5 m below the ice, the upper 4–6 m averaged heat flux estimates from the microstructure profiler agreed with the direct measurements to within 10%. During the experiment water column was stably, but weakly, stratified. Destabilizing buoyancy fluxes recorded close to the ice were absent at 5 m below the ice, and overall, turbulence production was dominated by shear. A scaling for dissipation employing production by both stress and buoyancy [Lombardo and Gregg, 1989. Similarity scaling of viscous and thermal dissipation in a convecting boundary layer. Journal of Geophysical Research 94, 6273–6284] was found to be appropriate for the under-ice boundary layer.  相似文献   

11.
The true or full ground motion information is frequently necessary in seismology to deal with a wide range of urgent scientific and applied problems; this information includes knowledge not only of ground motion along three axes at the recording site, but also the values of tilt or rotations of the surface at the site. This problem is usually attacked using a special type of seismic instrument-tiltmeters. Gyrotiltmeter is one of the many types of tiltmeters in which the gyroscope is used as the active sensor. The main obstacle in the way of developing effective long period seismic instruments, including gyrotiltmeters, consists in various sorts of noise, frequently not of seismic origin, which influence on the instrument increases as its frequency characteristic is extended toward longer periods. The present paper is concerned with problems arising in the use of optimal filters to detect seismic signals in records of a gyrotiltmeter where also noise may be present, e.g., that due to air pressure fluctuations. Examples are provided of tests of the algorithms, which clearly demonstrate that the application of the optimal filters to records of long period gyrotiltmeter channels can significantly enhance the signal/noise ratio to detect seismic signals disguised by induced noise.  相似文献   

12.
The Global Ozone Monitoring Experiment (GOME) onboard the ERS-2 satellite has been in operation since July 1995. The Norwegian ground-based total ozone network has played an important role both in the main validation during the commissioning phase and in the validation of upgraded versions of the analysis algorithms of the instrument. The ground-based network consists of various spectrometer types (Dobson, Brewer, UV filter instruments). The validation of the second algorithm version used until January 1998 reveals a very good agreement between GOME and ground-based data at solar zenith angles <60° and deviations of GOME total ozone data from ground-based data of up to ±60 DU (∼20%) at zenith angles ≥60°. The deviations strongly depend on the season of the year, being negative in summer and positive in winter/spring, The deviations furthermore show a considerable scattering (up to ±25 DU in monthly average values of 5° SZA intervals), even in close spatial and temporal coincidence with ground-based measurements, especially in the high Arctic. The deviations are also dependent on the viewing geometry/ground pixel size with an additional negative offset for the large pixels used in the backswath mode and at solar zenith angles ≥85°, compared to forward-swath pixels.  相似文献   

13.
We present sea level observations derived from the analysis of signal-to-noise ratio (SNR) data recorded by five coastal GPS stations. These stations are located in different regions around the world, both in the northern and in the southern hemisphere, in different multipath environments, from rural coastal areas to busy harbors, and experience different tidal ranges.The recorded SNR data show periodic variations that originate from multipath, i.e. the interference of direct and reflected signals. The general assumption is that for satellite arcs facing the open sea, the rapid SNR variations are due to reflections off the sea surface. The SNR data recorded from these azimuth intervals were analyzed by spectral analysis with two methods: a standard analysis method assuming a static sea level during a satellite arc and an extended analysis method assuming a time dependent sea level during a satellite arc.The GPS-derived sea level results are compared to sea level records from co-located traditional tide gauges, both in the time and in the frequency domain. The sea level time series are highly correlated with correlation coefficients to the order of 0.89–0.99. The root-mean-square (RMS) difference is 6.2 cm for the station with the lowest tidal range of 165 cm and 43 cm for the station with the highest tidal range of 772 cm. The relative accuracy, defined as the ratio of RMS and tidal range, is between 2.4% and 10.0% for all stations.Comparing the standard analysis method and the extended analysis method, the results based on the extended analysis method agree better with the independent tide gauge records for the stations with a high tidal range. For the station with the highest tidal range (772 cm), the RMS is reduced by 47% when using the extended analysis method. Furthermore, the results also indicate that the standard analysis method, assuming a static sea level, can be used for stations with a tidal range of up to about 270 cm, without performing significantly worse than the extended analysis method.Tidal amplitudes and phases are derived by harmonic analysis of the sea level records. Again, a high level of agreement is observed between the tide gauge and the GPS-derived results. Comparing the GPS-derived results, the results based on the extended analysis method show a higher degree of agreement with the traditional tide gauge results for stations with larger tidal ranges. Spectral analysis of the residuals after the harmonic analysis reveals remaining signal power at multiples of the draconitic day. This indicates that the observed SNR data are to some level disturbed by additional multipath signals, in particular for GPS stations that are located in harbors.  相似文献   

14.
本文通过四分量自检、相对标定内精度分析对东平地震台YRY-4钻孔分量应变观测资料进行可靠性分析,并结合滑动相关性计算、潮汐因子内精度对2套仪器数据进行了对比,证明YRY-4钻孔分量应变2面应变相关性高,相关系数接近1,相对标定内精度高,与体应变数据整体趋势一致。2套仪器观测环境一致,运行稳定,数据正常可靠,但也存在降雨、场地干扰特殊时段曲线表现不一致的情况。针对2种特殊情况结合相关性计算、S变换进行了对比分析。结果表明,降雨时段,因钻孔条件差别较大,2套仪器数据相关性较差,接近0;场地干扰时段,2套仪器观测系统均受到影响,频率域同步出现干扰信号,影响数据曲线形态及潮汐因子精度,但2套仪器面应变相关性达0.91。综合分析,东平台钻孔应变仪与体应变2套仪器观测系统是可靠稳定的。   相似文献   

15.
Long gravity records are of great interest when performing tidal analyses. Indeed, long series enable to separate contributions of near-frequency waves and also to detect low frequency signals (e.g. long period tides and polar motion). In addition to the length of the series, the quality of the data and the temporal stability of the noise are also very important. We study in detail some of the longest gravity records available in Europe: 3 data sets recorded with spring gravimeters in Black Forest Observatory (Germany, 1980–2012), Walferdange (Luxemburg, 1980–1995) and Potsdam (Germany, 1974–1998) and several superconducting gravimeters (SGs) data sets, with at least 9 years of continuous records, at different European GGP (Global Geodynamics Project) sites (Bad Homburg, Brussels, Medicina, Membach, Moxa, Vienna, Wettzell and Strasbourg). The stability of each instrument is investigated using the temporal variations of tidal parameters (amplitude factor and phase difference) for the main tidal waves (O1, K1, M2 and S2) as well as the M2/O1 factor ratio, the later being insensitive to the instrumental calibration. The long term stability of the tidal observations is also dependent on the stability of the scale factor of the relative gravimeters. Therefore we also check the time stability of the scale factor for the superconducting gravimeter C026 installed at the J9 Gravimetric Observatory of Strasbourg (France), using numerous calibration experiments carried out by co-located absolute gravimeter (AG) measurements during the last 15 years. The reproducibility of the scale factor and the achievable precision are investigated by comparing the results of different calibration campaigns. Finally we present a spectrum of the 25 years of SG records at J9 Observatory, with special attention to small amplitude tides in the semi-diurnal and diurnal bands, as well as to the low frequency part.  相似文献   

16.
We provide two new determinations of the oxygen isotopic composition of seawater during the last glacial maximum (LGM). High-resolution oxygen isotopic measurements were made on interstitial waters from Ocean Drilling Program (ODP) Sites 1168 and 1170 in the southeast Indian Ocean sector of the Southern Ocean. We use a diffusion-advection numerical model to calculate the glacial-interglacial change in bottom-water δ18Osw from the pore water δ18O profiles; the first such determinations from this part of the oceans. Statistical analyses of the model runs indicate that Circumpolar Deep Water (CDW) δ18Osw changed by 1.0-1.1±0.15‰ since the last glacial maximum (LGM). Our results are consistent with a previous calculation from a South Atlantic Southern Ocean location (ODP Site 1093) also situated within CDW. The new values determined in this study, together with previous estimates, are converging on a global average Δδ18Osw of 1.0-1.1‰.Using the calculated bottom-water δ18Osw, we have extracted the temperature component from the benthic foraminiferal δ18O record at Sites 1168 and 1170. Since the LGM, bottom waters at these two sites warmed by 2.6 and 1.9°C, respectively. The absolute temperature estimates for the LGM (−0.5°C [Θ=−0.6°C] at Site 1168 and −0.2°C [Θ=−0.4°C] at Site 1170) are slightly warmer than those reported from previous studies using the same technique, but are consistent with more homogenous deep-ocean temperatures during the LGM relative to the modern.  相似文献   

17.
The Bouguer anomaly and the total intensity magnetic maps of Saurashtra have delineated six circular gravity highs and magnetic anomalies of 40-60 mGal (10−5m/s2) and 800-1000 nT, respectively. Three of them in western Saurashtra coincide with known volcanic plugs associated with Deccan Volcanic Province (DVP), while the other three in SE Saurashtra coincide with rather concealed plugs exposed partially. The DVP represents different phases of eruption during 65.5±2.5 Ma from the Reunion plume. The geochemical data of the exposed rock samples from these plugs exhibit a wide variation in source composition, which varies from ultramafic/mafic to felsic composition of volcanic plugs in western Saurashtra and an alkaline composition for those in SE Saurashtra. Detailed studies of granophyres and alkaline rocks from these volcanic plugs reveal a calc-alkaline differentiation trend and a continental tectonic setting of emplacement. The alkaline plugs of SE Saurashtra are associated with NE-SW oriented structural trends, related to the Gulf of Cambay and the Cambay rift basin along the track of the Reunion plume. This indicates a deeper source for these plugs compared to those in the western part and may represent the primary source magma. The Junagadh plug with well differentiated ring complexes in western Saurashtra shows well defined centers of magnetic anomaly while the magnetic anomalies due to other plugs are diffused though of the same amplitude. This implies that other plugs are also associated with mafic/ultramafic components, which may not be differentiated and may be present at subsurface levels. Paleomagnetic measurements on surface rock samples from DVP in Saurashtra suggest a susceptibility of 5.5×10−2 SI units with an average Koenigsberger ratio (Qn) of almost one and average direction of remanent magnetization of D=147.4° and I=+56.1°. The virtual geomagnetic pole (VGP) position computed from the mean direction of magnetization for the volcanic plugs and Deccan basalt of Saurashtra is 30°N and 74°W, which is close to the VGP position corresponding to the early phases of Deccan eruption. Modeling of gravity and magnetic anomalies along two representative profiles across Junagadh and Barda volcanic plugs suggest a bulk density of 2900 and 2880 kg/m3, respectively and susceptibility of 3.14×10−2 SI units with a Qn ratio of 0.56 which are within the range of their values obtained from laboratory measurements on exposed rock samples. The same order of gravity and magnetic anomalies observed over the volcanic plugs of Saurashtra indicates almost similar bulk physical properties for them. The inferred directions of magnetization from magnetic anomalies, however, are D=337° and 340° and I=−38° and −50° which represent the bulk direction of magnetization and also indicate a reversal of the magnetic field during the eruption of these plugs. Some of these plugs are associated with seismic activities of magnitude ≤4 at their contacts. Based on this analysis, other circular/semi-circular gravity highs of NW India can be qualitatively attributed to similar subsurface volcanic plugs.  相似文献   

18.
The first phase (1997–2003) of the Global Geodynamics Project (GGP) has now been completed. Data from superconducting gravimeters (SGs) within GGP have shown great capabilities in a wide spectrum of geophysical applications from the tidal studies to the long-period seismology. Here, we compare the noise levels of the different contributing stations over the whole spectrum. We use three different processing procedures to evaluate the combined instrument-plus-site noise in the long-period seismic band (200–600 s), in the sub-seismic band (1–6 h) and in the tidal bands (12–24 h). The analysis in the seismic band has demonstrated that SGs are particularly well suited for the studies of the long-period normal modes and thus are complementary to long-period seismometers. In the sub-seismic band, the power spectral densities, computed over a period of 15 continuous days for every GGP station, cross the New Low Noise Model of Peterson from T = 16 min to T = 4.6 h. SG data are therefore appropriate for studying long-period seismic and sub-seismic modes. In the tidal bands, the noise comparison is realised by a least-squares fit to tides, local air pressure and instrumental drift, leading to gravity residuals where we estimate a standard deviation and average noise levels in different tidal frequency bands. Tidal gravity observations using SGs have also shown to be an independent validation tool of ocean tidal models, and they are therefore complementary to tide gauge and altimetric data sets. Knowledge of the noise levels at each station is important in a number of studies that combine the data to determine global Earth parameters. We illustrate it with the stacking of the data in the search for the gravity variations associated with the sub-seismic translational motions of the inner core, the so-called Slichter triplet.  相似文献   

19.
A data set of 199 sea surface temperature maps derived from the Advanced Very High Resolution Radiometer for the period 2000–2002 was processed to derive the position of the surface inshore thermal front of the Brazil Current (BCIF) in the SE Brazilian coastal and oceanic area. After the derivation of the position of the BC front for each image, the ensemble of digital frontal vectors was processed using the algorithm of frontal density (FD). For each 5′×5′ cell in the domain the calculated FD provided an index expressing the presence and persistence of the front in the area or the probability of finding the front in the region. In the paper we present the results of the FD analysis to get a better view of the space and time variability of the BC front in the region. The highest values of FD were in general observed close to or at the shelf break zone (between 200 and 1000 m isobaths). From 20°S to 23°S there is a tendency of BCIF to be positioned over the outer shelf, inshore of the 200 m isobaths. SE of Cape Sao Tome and S of Cape Frio it was observed a bimodal spatial distribution of highest FD caused by the presence of two semi-permanent frontal eddies. After moving offshore near Cape Frio, the BCIF tends to return to the shelf break zone south of 24°S probably due to a potential vorticity conservation mechanism. The position of the highest FD values calculated for different seasons confirms previous studies in that BCIF is closer to the coast during the summer and furthest offshore in the winter. Statistical analysis of the SST data gave for the BCIF an average SST gradient of 0.31°C km−1 with a standard deviation of 0.15°C km−1. A mean frontal width of 6 km was inferred from the average SST gradient and typical temperatures near the front at both sides, at outer shelf and in the BC itself. A Weibull probability density function can be fitted to describe the BCIF SST gradients with scale factor c=0.3460°C km−1 and shape factor k=2.1737. The BCIF SST gradient showed a seasonal variability with the smallest gradients in summer (~0.24 °C km−1) and the highest in autumn (~0.33 °C km−1). Using a three harmonic Fourier fit for the SST field near the BCIF, at the outer shelf and at interior of BC, it was possible to derive an analytical model for the time variability of the SST gradient of BCIF.  相似文献   

20.
Dense networks of wireless structural health monitoring systems can effectively remove the disadvantages associated with current wire‐based sparse sensing systems. However, recorded data sets may have relative time‐delays due to interference in radio transmission or inherent internal sensor clock errors. For structural system identification and damage detection purposes, sensor data require that they are time synchronized. The need for time synchronization of sensor data is illustrated through a series of tests on asynchronous data sets. Results from the identification of structural modal parameters show that frequencies and damping ratios are not influenced by the asynchronous data; however, the error in identifying structural mode shapes can be significant. The results from these tests are summarized in Appendix A. The objective of this paper is to present algorithms for measurement data synchronization. Two algorithms are proposed for this purpose. The first algorithm is applicable when the input signal to a structure can be measured. The time‐delay between an output measurement and the input is identified based on an ARX (auto‐regressive model with exogenous input) model for the input–output pair recordings. The second algorithm can be used for a structure subject to ambient excitation, where the excitation cannot be measured. An ARMAV (auto‐regressive moving average vector) model is constructed from two output signals and the time‐delay between them is evaluated. The proposed algorithms are verified with simulation data and recorded seismic response data from multi‐story buildings. The influence of noise on the time‐delay estimates is also assessed. Copyright © 2004 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号