共查询到20条相似文献，搜索用时 31 毫秒
1.
This paper presents a simulation model based on the finite element method. The method is used to analyze the motion response and mooring line tension of the flatfish cage system in waves. The cage system consists of top frames, netting, mooring lines, bottom frames, and floats. A series of scaled physical model tests in regular waves are conducted to verify the numerical model. The comparison results show that the simulated and the experimental results agree well under the wave conditions, and the maximum pitch of the bottom frame with two orientations is about 12o. The motion process of the whole cage system in the wave can be described with the computer visualized technology. Then, the mooring line tensions and the motion of the bottom frame with three kinds of weight are calculated under different wave conditions. According to the numerical results, the differences in mooring line tensions of flatfish cages with three weight modes are indistinct. The maximum pitch of the bottom frame decreases with the increase of the bottom weight. 相似文献
2.
A numerical model of flatfish cage is built based on the lumped mass method and the principle of rigid body kinematics. To validate the numerical model, a series of physical model tests are conducted in the wave flume. The numerical results correspond well with the data sets from physical model test. The effect of weight of bottom frame, height of fish net and net shape on motion responses of fish cage and tension force on mooring lines is then analyzed. The results indicate that the vertical displacements of float collar and bottom frame decrease with the increase in the weight of bottom frame; the maximum tension force on mooring lines increases with the increasing weight of bottom frame. The inclination angles of float collar and bottom frame decrease with the increasing net height; the maximum tension force increases obviously with the increase of net height. 相似文献
3.
Failure of net cage and mooring system is of great concern to the marine aquaculture industry. To avoid the structure failure in storm waves and current during typhoon events, net cage can submerge below the water surface in practice. A submersible net cage and mooring system is analyzed by numerical simulation and physical model test. The numerical model is established based on the lumped mass method and principle of rigid body kinematics. A series of physical model tests are conducted to validate the numerical model of single net cage and grid mooring system in waves and current. Numerical results correspond well with data obtained from physical model test. The results indicate that when net cage is submerged below the water surface, the deformation of net cage in waves can be improved significantly, and the tension force on the anchor line, bridle line and grid line will decrease significantly. However, the tension force on the buoy line in the submergence condition is larger than that in the floating condition. Different relative submergence ratios are also considered in our numerical simulation, and a relative submergence ratio equal to 0.1 is suggested here. The tension reduction ratio (56%) for the four-cage system is larger than that for the single-cage (52%) and double-cage systems (44%). 相似文献
4.
针对单点系泊(SPM)网箱系泊力大于传统网箱,离岸环境承受风浪时风险更高的问题,研究设计了一种相较传统圆形网箱拥有更小系泊力的船型网箱,运用正交原理制定了三因素三水平的试验方案,对网箱浮架进行了计算机数值模拟,分析网箱在波流共同作用下的水动力特性变化。研究表明,在兼顾经济成本与网箱安全性的条件下,长24 m,宽9 m,头部角度为60°的网箱浮架具有较优良的水动力性能和相对较低的养殖成本。该网箱系统能随着潮流改变方向而在锚点周围移动,从而极大减小网箱底部的养殖残渣堆积并降低锚固安装成本,可为我国深水网箱的发展提供一定的理论参考依据。 相似文献
5.
Based on the lumped-mass method and rigid-body kinematics theory, a mathematical model of a gravity cage system attacked by irregular waves is developed to simulate the hydrodynamic response of cage system, including the maximum tension of mooring lines and the motion of float collar. The normalized response amplitudes (response amplitude operators) are calculated for the cage motion response in heave and surge, and the mooring line tension response, in regular waves. In addition, a statistical approach is taken to determine the motion and tension transfer functions in irregular waves. In order to validate the numerical model of a gravity cage attacked by irregular waves, numerical predictions have been compared with the experimental observations in the time and frequency domain. The effect of wave incident angle on the float collar motion, mooring line tension and net volume reduction of the gravity cage system in irregular waves is also investigated. The results show that at high frequencies, the cage system has no significant heave motion. It tends to contour itself to longer waves. The variation amplitude of mooring line forces decreases as the wave frequency increases. With the increasing of wave incident angle, the horizontal displacement of the float collar increases. 相似文献
6.
This paper investigates the intact and damage survivability of a floating–moored Oscillating Water Column (OWC) device using physical model experiments and Computational Fluid Dynamics (CFD) simulations. Different extreme wave conditions have been tested using irregular and regular wave conditions. The device was moored to the tank floor via four vertical taut lines and the effect of the mooring line pre–tension on the device response was studied. It was found that the instantaneous position of the floating device was a key factor in the survivability analysis such that a certain irregular wave train that might not include the largest wave could induce the maximum response. Reducing the pre–tension minimized the maximum surge, but significantly increased the maximum tension due to mooring slack events causing snatch loads. A design regular wave with a period equal to the peak period and a height of 1.9–2.0 times the significant wave height could reasonably predict the same maximum line tension as the irregular sea state, but a smaller wave height was required to achieve the maximum surge. A single failure in the mooring system increased the maximum tension by 1.55 times the intact tension. For a damaged mooring system, using the same design regular wave condition derived from the survivability analysis with an intact mooring system could result in overestimating the maximum tension by more than 20% in comparison to the tension from the irregular sea state, but a smaller regular wave height or a different regular wave condition representing another sea state could lead to the same maximum tension. This highlighted the importance of investigating survival conditions with a damaged mooring system instead of simply using the same conditions derived for the intact mooring system. 相似文献
7.
基于物理模型试验,探究畸形波和不规则波作用下浮体系泊张力差异问题。讨论相对波高、相对周期和畸形波参数α1对系泊张力的影响。结果显示:畸形波参数α1和浮体系泊张力显著相关。在α1=2.0～2.83范围内,畸形波作用下迎浪侧系泊张力最大值可达不规则波作用的1.9倍。在相对波高Hs/d=0.032～0.097范围内,畸形波作用下迎浪侧系泊张力最大值显著大于不规则波的作用结果,但畸形波和不规则波对应的1/3值及平均值几乎一致。就相对周期影响而言,迎浪侧系泊张力最大差别出现在谱峰周期Tp0p范围内。频域方面采用小波分析方法讨论畸形波和不规则波作用下浮体系泊张力时频谱特征,两种波浪作用下系泊张力时频特征有显著差别。 相似文献
8.
我国南海海域海洋环境条件复杂且海水密度垂直层化现象显著,内孤立波活动频繁,因内孤立波而造成海洋开采平台破坏的案例屡见不鲜。依托水动力计算软件AQWA二次开发功能,采用Kdv方程,借助Fortran语言将深水半潜式平台立柱、浮箱、系泊系统3部分的内孤立波作用力叠加到外力项中,联合求解半潜式平台的6自由度动力响应特性。数值模拟结果表明,在内孤立波作用下,半潜式平台的运动及系泊线张力均受到了显著的影响。在不考虑系泊系统受内孤立波作用时,平台在纵荡和横荡方向上产生较大的漂移运动,最大偏移量较无内孤立波情况下增加了8倍;系泊线最大张力提高了17%,增加了系泊线断裂的风险。在考虑系泊系统受内孤立波作用时,平台的纵荡和横荡运动响应在原响应基础上继续提高15%,但是系泊线张力变化不大。内孤立波不同浪向下的平台纵荡和横荡响应相差也很明显;系泊系统合力在不同方向上的大小决定了平台不同方向上运动的大小。 相似文献
9.
FSRU码头系泊模型实验与数值模拟研究 总被引：1，自引：0，他引：1
FSRU在恶劣环境条件下的作业和安全停靠性能与系泊缆张力、靠垫挤压应力、船体6自由度运动等参数有关。针对FSRU码头处海洋环境条件,进行FSRU不同装载状况的模型实验,获得FSRU的6自由度运动及其系泊载荷的动力特性。基于三维辐射和绕射理论,使用Sesam软件进行频域计算,以此为基础在相应海洋环境条件下进行时域耦合分析,获得FSRU 6自由度运动、系泊载荷、靠垫应力等参数的响应时历。结果表明:30%装载、横浪条件下FSRU的运动响应最大,系泊缆张力未达到破断值,靠垫压力超过其压缩60%时的载荷;模型实验对FSRU运动响应和系泊缆张力的预测结果可信,靠垫受力情况需要数值仿真进行辅助研究。 相似文献
10.
我国的边际油田大多年产量小且开发年限短，周围没有可依托设施的油田。针对此情况，可采用“蜜蜂式”开发模式。针对浸没式可移动外输终端这一新型概念设计，选取关键工况开展了时域耦合分析，研究了系泊系统参数对可移动外输终端最大水平位移和系泊缆最大张力的影响。以可移动外输终端最大水平位移和系泊缆最大张力最小为优化目标，以系泊缆结构安全为约束条件，构建了系泊系统多目标优化模型。分别建立了基于NSGA-Ⅱ和多目标粒子群算法的系泊系统优化框架，并应用这两种算法对系泊系统进行了优化设计。结果表明，NSGA-Ⅱ和多目标粒子群算法均可以解决系泊系统多目标优化问题，粒子群算法优化速度快，但通过NSGA-Ⅱ得到的Pareto前沿优化性能更好，因此更适合开展浸没式可移动外输终端的系泊系统优化。 相似文献
11.
设计了一种新型网箱浮架系统,利用SESAM对其进行了频域水动力分析以及考虑不规则波浪、风、流载荷和系泊共同作用的时域耦合分析,并与传统双浮管网箱浮架系统进行了分析对比,得到方形网箱与圆形网箱的水动力特性的差异以及各自的优缺点,对实际中网箱的开发设计有一定的借鉴意义;通过计算,证明新型网箱浮架系统在工作海况能正常工作,在极端海况下也能满足安全性的要求;最后对4种常见系泊方式进行了时域耦合分析,得到了四种系泊方式的系泊特性,对实际工程中系泊方式的选择有一定的参考意义。 相似文献
12.
Accurate prediction of the offshore structure motion response and associate mooring line tension is important in both technical applications and scientific research. In our study, a truss spar platform, operated in Gulf of Mexico, is numerically simulated and analyzed by an in-house numerical code ‘COUPLE'. Both the platform motion responses and associated mooring line tension are calculated and investigated through a time domain nonlinear coupled dynamic analysis. Satisfactory agreement between the simulation and corresponding field measurements is in general reached, indicating that the numerical code can be used to conduct the time-domain analysis of a truss spar interacting with its mooring and riser system. Based on the comparison between linear and nonlinear results, the relative importance of nonlinearity in predicting the platform motion response and mooring line tensions is assessed and presented. Through the coupled and quasi-static analysis, the importance of the dynamic coupling effect between the platform hull and the mooring/riser system in predicting the mooring line tension and platform motions is quantified. These results may provide essential information pertaining to facilitate the numerical simulation and design of the large scale offshore structures. 相似文献
13.
基于三维频域势流理论,计算船体的水动力参数;采用动态耦合方法分析了深海半潜式生产平台各系统之间的相互作用特征,研究了立管系统对锚泊系统定位能力的影响。计算结果表明,立管系统在一定程度上增加了整个系统的刚度,其所受的附加质量和阻尼可降低平台的低频响应,从而降低平台的偏移和系泊缆的张力;海流将增大立管上的拖曳力,使平台偏移更远,锚索上的张力更大;立管系统对锚泊系统定位性能的最终影响需综合考虑多种因素的叠加。对目标平台而言,由于服役海域的流速较大,对立管的拖曳作用较为明显。因此,为确保平台的安全性,当服役海域流速较大时,带有多立管的平台,其锚泊系统的设计应考虑立管的影响。 相似文献
14.
波浪作用下刚性框架浮体及其锚绳运动数值模拟精度分析 总被引：2，自引：1，他引：1
由小尺度刚性杆件构成的复杂结构近年来多用于海洋平台建设和海洋监测浮标制作以及海洋增养殖人工浮鱼礁的设计。采用有限单元法和集中质量点法建立波浪作用下刚性框架浮体及其锚绳运动数值模型,探讨空间单元划分、时间离散步长、数据保存格式对刚性框架浮体和柔性锚绳运动模拟精度的影响,分别给出此三者之间的匹配关系。研究结果表明:框架浮体的单元划分可依据是否出水给定,单元的划分比建议取0.05;锚绳的单元划分与其上端连接的浮体浮力有关,当锚绳的拉力主要由上端浮体浮力产生时锚绳单元的划分影响较小,当锚绳的拉力主要由波浪力产生时锚绳单元的划分比建议取0.02;空间单元划分与时间离散步长存在匹配关系,通过减小时间步长来追求数值模拟精度时必须同时考虑保存运动物理量截断误差的影响。 相似文献
15.
In this paper, a methodology for designing mooring system deployment for vessels at varying water depths is proposed. The Non-dominated Sorting Genetic Algorithm-II(NSGA-II) is combined with a self-dependently developed vessel-mooring coupled program to find the optimal mooring system deployment considering both station-keeping requirements and the safety of the mooring system. Two case studies are presented to demonstrate the methodology by designing the mooring system deployments for a very large floating structure(VLFS) module and a semi-submersible platform respectively at three different water depths. It can be concluded from the obtained results that the mooring system can achieve a better station-keeping ability with relatively shorter mooring line when deployed in the shallow water. The safety factor of mooring line is mainly dominated by the maximum instantaneous tension increment in the shallow water, while the pre-tension has a decisive influence on the safety factor of the mooring line in the deep water. 相似文献
16.
As current attention of the offshore industry is drawn by developing pilot farms of Floating Wind Turbines (FWTs) in shallow-water between 50m and 100m, the application of nylon as a mooring component can provide a more cost-effective design. Indeed, nylon is a preferred candidate over polyester for FWT mooring mainly because of its lower stiffness and a corresponding capacity of reducing maximum tensions in the mooring system. However, the nonlinear behaviors of nylon ropes (e.g. load-elongation properties, fatigue characteristics, etc.) complicate the design and modeling of such structures. Although previous studies on the mechanical properties and modeling of polyester may be very good references, those can not be applied directly for nylon both on testing and modeling methods. In this study, first, an empirical expression to determine the dynamic stiffness of a nylon rope is drawn from the testing data in the literature. Secondly, a practical modeling procedure is suggested by the authors in order to cope with the numerical mooring analysis for a semi-submersible type FWT taking into account the dynamic axial stiffness of nylon ropes. Both the experimental and numerical results show that the tension amplitude has an important impact on the dynamic stiffness of nylon ropes and, as a consequence, the tension responses of mooring lines. This effect can be captured by the present modeling procedure. Finally, time domain mooring analysis for both Ultimate Limit State (ULS) and Fatigue Limit State (FLS) is performed to illustrate the advantages and conservativeness of the present approach for nylon mooring modeling. 相似文献
17.
参考英国的Kincardine风机采用的新式的Semi-Spar概念,结合spar式基础和半潜式基础的特点,提出了一种新式海上浮式风机平台模型,并基于三维势流理论,利用AQWA软件进行水动力计算,验证新式平台可靠性。分析了在风、浪、流荷载联合作用下,锚链竖向夹角、系缆数量对风机浮式平台运动性能和系泊张力的影响,对系泊系统进行优化,并验证极端工况下的可靠性。结果证明风机平台水平运动和纵摇运动幅值较小,但垂荡幅值略大,而通过减小锚链竖向夹角可以控制平台运动响应幅值,增加系缆数量可以同时减小系泊张力大小。计算结果证明了新型Semi-Spar式海上风机平台可行性,为浮式风机平台及系泊系统的设计提供参考。 相似文献
18.
This paper presents a new procedure for the optimization of the mooring design of floating platforms, in which an automatic design sequence is also established. Regarding the optimization philosophy, the following aspects are dealt with:
- • The optimization of the platform heading and its mooring pattern, taking into account the environmental force spreading;
- • optimum line length or line tension for each mooring line, associated to the optimization of the mooring line materials and sizes.
19.
由于浅水深条件下悬链线系泊系统的性能对系泊缆长度和几何形状更为敏感,悬链线系泊系统的安装误差对其性能的影响较深水条件下的更为显著。因此首先对适用于半潜漂浮式风机的悬链线系泊系统施工进行研究,分别确定了锚安装位置误差、系泊缆预铺误差和系泊缆与漂浮式基础回接误差的来源,并根据施工条件给出了误差值。之后,以浮体动力学仿真作为手段,对系泊缆系统施工误差对其性能的影响进行基于时域仿真的量化研究。研究表明,锚安装位置误差对系泊系统性能影响不大,但系泊缆预铺和回接的误差对系泊系统性能的影响较大。系泊缆回接的误差可造成系泊缆张力平均值和标准差与设计值偏差近20%,可能对系泊系统疲劳寿命评估产生较大的影响。与系泊缆回接误差相比,系泊缆预铺误差的产生原因更为复杂,由于系泊缆预铺误差往往导致系泊缆长度增长,存在误差的系泊缆张力的各项统计值总体偏小,但可能会造成同组无误差系泊缆的张力过载。 相似文献
20.