共查询到20条相似文献，搜索用时 46 毫秒
1.
2.
柔性微型桩水平承载力数值模拟 总被引：8，自引：0，他引：8
针对微型桩水平载荷的现场测试和原位试验相对困难,对其开展的研究很少,其荷载传递性状、受力特征等尚不能完全确定的问题,运用有限元软件ABAQUS对现场柔性微型桩（桩长与桩径之比一般大于50左右）试验进行数值模拟。数值分析结果和现场实测结果基本一致,说明模拟中的参数是有效并正确的,基本上能反映现场的实际情况。通过有限元模拟,探讨了微型桩在水平载荷作用下的工作性能,分析了微型桩的各个参数对其水平承载力的影响,给出了桩长、桩径、桩身弹性模量的合理取值,研究结果表明：较大的桩径、较高的土体摩擦角对提高柔性微型桩水平承载力有显著作用 相似文献
3.
4.
基于典型冲刷坑形态,通过改变冲刷深度来模拟不同局部冲刷作用,对典型的9桩群桩进行了冲刷前、后水平承载试验,对相同参数的单桩进行了平行对比试验,详细分析了荷载-位移特性、桩身弯矩分布、群桩效率系数以及荷载分担比的变化规律。结果表明,随着冲刷深度增加,单桩和9桩基础水平承载力均呈现减弱趋势,水平群桩效率系数逐渐增大,承台约束作用效应更加明显,桩身弯矩增大,最大弯矩点位置向桩端移动,前排桩荷载分担比增大,中、后排桩荷载分担比减小;前排角桩受冲刷深度和水平荷载影响最大,设计时需采取有效的加强措施。 相似文献
5.
风积沙地基装配式偏心基础抗拔试验研究 总被引：1，自引：0，他引：1
在毛乌素沙漠中开展装配式偏心基础在上拔、上拔+水平力组合荷载作用下的现场试验研究。根据试验加载过程中监测的基础顶部位移、地表竖向位移及基础底板土压力数据,分析基础顶部的荷载-位移特性,研究装配式偏心基础的抗拔承载机制。结果表明,（1）在上拔、上拔和水平力组合作用下,基础顶部上拔和水平位移曲线均呈二阶段的承载特性;（2）当仅受上拔荷载作用时,基础偏心引起的附加弯矩,使得基础底板产生偏转,基础及底板上覆部分沙土自重抵抗上拔荷载,而在上拔和水平力组合荷载工况下,基础偏心引起的附加弯矩小,与上拔荷载工况相比,基础极限抗拔承载力提高8.7％,即在组合荷载工况下装配式偏心基础能够发挥更多的沙土来抵抗上拔荷载;（3）根据装配式偏心基础的抗拔承载机制,引入外荷载合力作用线与支架作用线之间的夹角δ来反映水平荷载对装配式基础抗拔破坏因子的影响,其影响规律为装配式基础的抗拔破坏因子随δ增加而降低。 相似文献
6.
戈壁地基扩底掏挖基础抗拔试验及其位移计算 总被引：1，自引：0，他引：1
在甘肃和新疆7个戈壁碎石土场地完成了46个扩底掏挖基础抗拔现场试验,分析了基础抗拔荷载-位移曲线的阶段特征,应用L1-L2方法确定了所有基础抗拔承载力和位移。采用归一化荷载-位移双曲线模型对实测荷载-位移曲线进行拟合,得到了各试验基础归一化荷载-位移双曲线模型拟合参数取值及其统计规律,给出了同时考虑抗拔基础极限承载力计算理论模型误差和归一化荷载-位移双曲线模型不确定性时基础荷载和位移的计算方法。结果表明：戈壁碎石土扩底掏挖基础抗拔荷载-位移曲线呈初始弹性直线段、弹塑性曲线过渡段和直线破坏的3阶段变化规律,归一化荷载-位移双曲线模型可较好拟合基础实测荷载-位移曲线,归一化荷载-位移双曲线模型不确定性可转化为该双曲线模型拟合参数的不确定性,基于强度和变形统一的工程设计更有利于工程安全。 相似文献
7.
基于小波函数伸缩平移的特性,建立了能反映锚杆界面黏结?软化?滑动力学特性的剪应力?位移非线性本构模型,克服了三折线软化界面模型需要分段分析的复杂性。结合锚固体荷载传递的力学微分方程,推导了锚杆拉拔荷载?位移曲线的解析表达式,并提出了锚固体位移、轴力、周边剪应力的数值计算方法和步骤。通过算例分析,得到不同张拉位移作用下的锚固段位移、轴力和剪应力分布,获得的锚杆拉拔荷载?位移和锚杆轴向力分布计算值与实测值进行了对比分析,验证了该方法的有效性。该方法能准确地反映锚杆在不同荷载下的传力机制,模拟锚杆从弹性工作状态到塑性滑移的全过程。最后,通过参数分析,得到了锚杆锚固长度、轴向刚度以及锚固界面本构参数对锚固效果的影响规律。 相似文献
8.
基于虚土桩模型,分析了层状地基中桩端土性对单桩沉降特性的影响。首先,以虚土桩扩散角反映桩端土层应力扩散效应,将桩端一定锥角范围内由桩端至基岩面的土体视为虚土桩,并根据其变截面特性,将虚土桩沿纵向划分为有限个微元段。然后,对桩及虚土桩桩侧土体采用理想弹塑性荷载传递模型,利用荷载传递法,推导了层状地基中以桩侧土塑性发展深度为变量的单桩荷载-沉降递推计算方法,并进一步得到了桩身轴力及桩侧摩阻力递推计算式。在此基础上,给出了荷载传递模型参数选取方法,并分析了虚土桩临界深度的影响因素及由实测荷载-沉降曲线反演虚土桩扩散角的可行性。最后,利用该方法分析了桩端沉渣和软弱下卧层对荷载-沉降曲线的影响。结果表明,考虑桩端土层应力扩散效应时,通过计算得到的桩顶及桩端荷载-沉降曲线与实测曲线吻合较好;当桩端存在沉渣或软弱下卧层时,采用虚土桩模型的单桩沉降计算方法可以在一定程度上反映沉渣特性及软弱下卧层埋深等因素对桩顶荷载-沉降曲线的影响。 相似文献
9.
CFG桩(cement-fly ash-gravel pile)复合地基是一种重要的地基处理形式,在日益增加的大面积住宅和商业开发中作用越来越突出,然而该种桩型的加卸荷-沉降变形特性仍然需深入研究,尤其在概率评估方面。根据北京星光影视股份有限公司生产科研基地项目工地中的21根CFG桩单桩静载试验和32个复合地基静载试验的原位加卸载测试成果,采用两参数的双曲线或幂曲线回归拟合了每一条加荷-变形曲线。由于土体的内在各向异性和其强度的变异性,评估整个场地的加荷-变形曲线时,其回归参数表现出了较大的离散性。将一个场地的多组回归参数组成一个随机向量,其加载-位移曲线的不确定性可由简单的两变量随机向量体现,引入双变量联结函数（Copula）描述随机回归参数间的相依性。最后,考虑正常使用极限状态,采用基于Copula函数的模拟模型计算了CFG桩复合地基的可靠度指标。研究结果有助于改进CFG桩复合地基的概率设计与评估。 相似文献
10.
工程中多采用基础上拔静载试验中基础顶部荷载-位移曲线获取基础的承载力,忽略了基础周围土体的变形破坏过程,而实际工程中均是基础周围地基土体发生破坏。为研究扩底基础与其周围土体在抗拔承载特性方面的差异,以黄土地基中的9个扩底基础为研究对象,通过现场全尺寸基础的上拔静载试验,分别获得基础顶部与地表的上拔荷载-位移曲线,并进一步对基顶与地表处的荷载-位移曲线变化特征、抗拔承载力取值进行对比分析。结果表明,两处的荷载-位移曲线变化特征相似,相同上拔荷载作用下地表处的位移量均小于基础处位移量,差异以初始弹性阶段变形最为突出;两者在弹性极限荷载QL1取值方面,相差较大,但随着地基基础由弹性向塑性发展,差异逐渐减小,两者塑性极限荷载QL2取值基本相同。结合上拔扩底基础的破坏模式,分析出上述差异主要由于基础与周围土体之间变形不协调所致,加载初期基础顶部的上拔位移包括基础拔出量和上部土体压缩量,当上部土体压密后压缩变形消失,地基基础成为一个整体,上拔基础与周围土体的变形趋于协调。 相似文献
11.
This paper aims at finding force-displacement relationships to be employed in the design of bucket foundations for offshore wind turbine. This is accomplished by combining small-scale tests and element tests within a theoretical framework. A similitude theory, regarding the lateral displacement of bucket foundations under horizontal load, is put forward. A constitutive law of the soil and a load-displacement relationship for the bucket foundation are theoretically obtained. Triaxial tests of sand, and small-scale tests of bucket foundation, are respectively employed to corroborate the theory. Attention is given to the different behaviour shown during the compressive and dilative phases of the soil. Some analogy between triaxial tests and tests of bucket foundation are pointed out. A theoretically derived power law is found capable to represent the dimensionless horizontal load-displacement curves of experimental results. In accordance with the theory, the exponent of the power law slightly varies between tests with considerably different features. The non-dimensional moment-rotation relationship is represented by a power law as well. The approach is considered valid for fatigue design. The study may be an interesting source for further researches on long-term cyclic horizontal loading. 相似文献
12.
桩-土界面特性对砂土地基中抗拔桩承载特性影响的模型试验研究 总被引：2，自引：0，他引：2
针对砂土地基中不同L/d的抗拔桩进行了模型试验,模型桩采用了3种不同界面,结合界面剪切试验探讨了桩-土界面特性对抗拔桩荷载-位移曲线、极限承载力及残余承载力的影响,得到了以下几点结论：模型桩长径比L/d不同时,每种界面抗拔桩荷载-位移曲线是类似的,光滑钢桩上拔力达极限承载力后保持不变,粗糙界面模型桩上拔力达极限承载力后降低,直至达残余承载力;抗拔桩达极限承载力时的静止土压力系数K受桩-土界面粗糙程度的影响,界面越粗糙,K值越大;界面越粗糙,抗拔桩残余承载力与极限承载力的比值越小,该比值随L/d的变化较小;对于粗糙界面抗拔桩,残余承载力与极限承载力的差别一部分是由于桩-土界面摩擦角的降低引起的,另一部分是抗拔桩达到极限承载力后作用在桩表面上的水平土压力降低引起的。 相似文献
13.
A new type of micropile, the waveform micropile, has been developed to provide improved load-bearing capacity compared with that of a conventional micropile. The waveform micropile has a wave-shaped grout with a partially enlarged shear key formed by the jet grouting method on the cylindrical shaft of the micropile. Previous research has determined that the waveform micropile can be installed faster than the conventional micropile and that the bearing capacity increases as the wave-shaped grout provides additional shaft resistance between the ground and the grout. In this study, a series of centrifuge model tests were conducted on the waveform micropile model with various wave-shaped grouts to analyze the relationship between the arrangement of the shear key and the load-bearing mechanism of the waveform micropile. The load–settlement relationship and the load-transfer mechanism were analyzed based on the test results of six test micropiles, including three waveform micropiles with a single shear key at various depths, one waveform micropile with a multiple shear key along the pile depth, and two micropiles with only a cylindrical shape. The test results showed that the ultimate bearing capacity of the waveform micropile was over two times greater than that of the conventional micropile. The rate of increase in the bearing capacities of each waveform micropile differed with the shape of the shear key. Furthermore, the characteristics of the load-sharing ratio due to the shaft resistance and end bearing varied depending on the shape of the waveform micropiles.
相似文献14.
An elastoplastic model for the analysis of a driven pile extended at the bottom with a micropile under axial load is presented. The model is an extension of the integral equation method of Poulos and Davis. The finite-difference scheme used to obtain the pile displacements is reformulated to take into account the discontinuity in the stress distribution at the joint between pile and micropile. The results obtained with the proposed method are compared with the outcomes of a more sophisticated finite element simulation, and also with data from full-scale load tests. Reasonably good agreement is obtained in both cases. 相似文献
15.
This article focuses on the statistical characterisation and stochastic modelling of the load-displacement behaviour of shallow footings on cohesionless soils and on the probabilistic estimation of settlement for serviceability limit state design (LSD). The study relies on a field database of 30 full-scale footings subjected to vertical loading with cone penetration testing data available for each site. The performance of three load-displacement models in replicating field data is assessed comparatively through statistical analysis. Load-displacement uncertainty is subsequently modelled probabilistically to perform Monte Carlo Simulation (MCS)-based estimation of footing settlement using the best-performing power law model. The dependence among load-displacement model parameters is investigated and replicated using copula theory. Samples are generated to account for parametric uncertainties in model inputs. The simulation output samples of settlement are examined statistically in order to assess the relevance of parametric and load-displacement uncertainties in settlement estimation, as well as the importance of accounting for correlation between power law model parameters. A simple analytical model for the estimation of settlement at any target reliability level is obtained on the basis of the outputs of MCS. The model can be practically implemented in geotechnical LSD at serviceability limit states. 相似文献
16.
为研究珊瑚砂地基下膨胀混凝土桩竖向承载特性,开展了室内单桩竖向静载模型试验,分析了膨胀混凝土桩的单桩荷载-位移曲线以及轴力、桩侧摩阻力等沿桩长分布特性,与PLAXIS 3D软件数值模拟结果进行对比并探究了线膨胀率对承载特性的影响。结果表明：珊瑚砂中膨胀混凝土桩的荷载位移曲线呈现缓变型,在加载过程中,荷载主要由桩侧摩阻力承担,轴力随着深度的增加而减小,桩侧摩阻力随深度先增加后逐渐减小,随荷载的增加逐渐发挥作用。随着膨胀剂用量的增加,桩身线膨胀量逐渐增加,桩-土相互作用更加明显。添加25% HCSA型膨胀剂可提高近20%的极限承载力和56%的极限侧阻力,提高桩体线膨胀率可以有效提高桩的极限承载力和侧摩阻力。该研究可为珊瑚砂桩基工程设计提供参考。 相似文献
17.
水平荷载作用下PCC桩复合地基工作性状 总被引：5，自引：1，他引：4
利用河海大学岩土所自行研制开发的大型试验模型槽进行PCC桩水平承载足尺试验,实测得到了水平荷载作用下桩身弯矩分布。利用三维弹塑性有限元方法,研究了PCC单桩与等截面实心圆桩、PCC桩复合地基与等截面实心圆桩复合地基在水平荷载作用下的工作性状,对其桩身弯矩和水平位移的分布规律进行了比较,分析了竖向荷载、褥垫层厚度、基础埋深和置换率对PCC桩复合地基桩身性状的影响。研究表明,PCC桩复合地基在水平荷载作用下,随着竖向荷载、褥垫层厚度、基础埋深和置换率的增加,其桩身弯矩和水平位移随之减小。因此,在PCC桩复合地基设计时可以通过适度调整这些影响参数来减小水平荷载作用下的桩身弯矩和水平位移,确保桩身的安全。 相似文献
18.
Pile foundation is one of the most commonly used and suitable foundations to support transmission line structure, especially in seasonally frozen soil regions and permafrost regions. Axial compression is the controlling condition in the design of foundations for such structures as bridges and buildings, while uplift and overturning will control the design of transmission line structure foundations. This paper presents an extensive overview of previous studies including experimental (e. g., laboratory model test and full-scale field load test), analytical/theoretical (e. g., limit equilibrium and limit analysis based on plasticity)and numerical(e. g., finite difference and finite element methods). The review indicates that study on the uplift behavior of pile foundation in frozen soil is relatively limited, particularly in the case of combined effect of axial uplift and lateral loading. Interaction between pile and frozen soil and mechanism of load transfer along the pile shaft and around the pile tip still remain unclear. Therefore, this paper implements finite difference analysis within FLAC3D to investigate the behavior of pile foundation in frozen silty clay and gravelly sand under axial uplift behavior and the effect of ground condition and lateral loading on the uplift behavior. Because of the axisymmetric condition of the problem studied, only half of the model is simulated. The chosen domain of the medium is discretized into a set of quadrilateral elements and the pile is discretized by the cylinder element. The interaction between the soil and pile is considered according to interface elements. Mohr-Coulomb criterion is adopted to model the soil behavior (perfectly elastic-plastic), while the pile is simply considered as a rigid body. The soil parameters such as Young’s modulus, cohesion and internal friction angle used for numerical analyses are determined by laboratory tests and estimated according to the empirical correlations with in-situ tests. The present numerical modeling is verified with the results from field loading tests on pile foundations in Qinghai-Tibet ±550 kV transmission line project. On this basis, parametric studies are carried out to uncover the behavior of pile in frozen soil. It is observed that pullout is the dominant failure mechanism of pile and the uplift load-displacement curve clearly exhibits an asymptote, consisting of initially linear elastic, nonlinear transition, and finally linear regions. These results are consistent with the observations in a few previous studies. In addition, larger uplift capacity of pile foundation in freezing period and gravelly sand is gained (about 20%). Lateral loading increases the deflection and therefore, decreases the uplift capacity of pile foundation. For the convenience of using the results obtained in practice, the values of uplift factor for pile foundation in silty clay and gravelly sand are provided. Finally, it should be noted that the method used, and the results obtained in the current work could be useful for engineers and designers, at least providing them some qualitative evidence for pile design in seasonally frozen soil regions and permafrost regions. This is important and necessary to ensure the safety of construction in such regions. Meanwhile, numerical analyses in the current work can be a benchmark example for subsequent research studies. © 2022 Science Press (China). 相似文献
19.
With the rising needs of better prediction of the load-displacement performance of grouted anchors in an era of developing large-scale underground infrastructures,the existing methods in literature lack an accurate analytical model for the real-life projects or rigorous understanding of the parameters such as grouting pressures.This paper proposes Fast ICA-MARS as a novel data-driven approach for the prediction of the load-displacement performance of uplift-resisting grouted anchors.The hybrid and data-driven Fast ICA-MARS approach integrates the multivariate adaptive regression splines(MARS)technique with the Fast ICA algorithm which is for Independent Component Analysis(ICA).A database of 4315 observations for 479 different anchors from 7 different projects is established.The database is then used to train,validate and compare the Fast ICA-MARS approach with the classical MARS approach.The developed Fast ICA-MARS model can provide more accurate predictions than MARS.Moreover,the developed Fast ICA-MARS model is easy to interpret since the evaluation of the parameter importance of the independent components can be conducted along with the considerations of the correlations with the original variables.It is noteworthy to point out that the grouting pressures play a central role in the proposed model,which is considered of paramount importance in engineering practices but has not been properly taken into account in any prior analytical or empirical predictive models for the load-displacement relationships. 相似文献
20.
Unlike conventional grouted micropiles, screw micropiles have been recently introduced to the foundation industry. Full-scale field tests of screw micropiles were carried out at a cohesive soil site. The screw micropiles have a diameter varying from 76 to 114 mm and a length varying from 1.6 to 3 m, and spiral threads welded on the lower half of the steel tubular shaft. Site investigation from cone penetration tests (CPT) and laboratory testing implies that the soil was medium to stiff, low plasticity clay. Six axial monotonic and three axial cyclic load tests were performed on three micropiles. One micropile was instrumented with strain gauges to investigate the shaft load distribution during loading. The axial cyclic loading was intended to simulate cyclic inertia load during vertical ground motions. Results showed that the micropiles behave as frictional piles during monotonic tests; the unit shaft resistance and adhesion coefficient were calculated and compared with results in the literature. The end installation torque was estimated using CPT shaft resistance and was shown to agree reasonably with the measured torque. Under axial cyclic loading, the micropiles underwent small cumulative displacements and the magnitude of the displacement decreased with increasing pile length and diameter. Cyclic loading redistributed the load transfer along different segments of the micropile. Negative skin resistance was observed along the smooth pile shaft when the pile underwent decreasing axial loading.
相似文献