首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 46 毫秒
1.
Aluminum foils from the Stardust cometary dust collector contain impact craters formed during the spacecraft's encounter with comet 81P/Wild 2 and retain residues that are among the few unambiguously cometary samples available for laboratory study. Our study investigates four micron‐scale (1.8–5.2 μm) and six submicron (220–380 nm) diameter craters to better characterize the fine (<1 μm) component of comet Wild 2. We perform initial crater identification with scanning electron microscopy, prepare the samples for further analysis with a focused ion beam, and analyze the cross sections of the impact craters with transmission electron microscopy (TEM). All of the craters are dominated by combinations of silicate and iron sulfide residues. Two micron‐scale craters had subregions that are consistent with spinel and taenite impactors, indicating that the micron‐scale craters have a refractory component. Four submicron craters contained amorphous residue layers composed of silicate and sulfide impactors. The lack of refractory materials in the submicron craters suggests that refractory material abundances may differentiate Wild 2 dust on the scale of several hundred nanometers from larger particles on the scale of a micron. The submicron craters are enriched in moderately volatile elements (S, Zn) when normalized to Si and CI chondrite abundances, suggesting that, if these craters are representative of the Wild 2 fine component, the Wild 2 fines were not formed by high‐temperature condensation. This distinguishes the comet's fine component from the large terminal particles in Stardust aerogel tracks which mostly formed in high‐temperature events.  相似文献   

2.
Abstract– We have shown in laboratory experiment that hypervelocity impacts on a solar cell produce ejecta that can be captured on aluminum (Al 1100) foil or in low density (33 kg m?3) aerogel. The origin of the secondary impacts can be determined by either analysis of the residue in the craters in the foils (which preserve an elemental signature of the solar cell components) or by their pointing direction for tracks in the aerogel (which we show align with the impact direction to ± 0.4°). This experimental evidence explains the observations of the NASA Stardust mission which has reported that the majority of tracks in the aerogel collector used to collect interstellar dust actually point at the spacecraft’s solar panels. From our results, we suggest that it should also be possible to recognize secondary ejecta craters in the Stardust mission aluminum foils, also used as dust sampling devices during the mission.  相似文献   

3.
Comet 81P/Wild 2 samples returned by NASA's Stardust mission provide an unequalled opportunity to study the contents of, and hence conditions and processes operating on, comets. They can potentially validate contentious interpretations of cometary infrared spectra and in situ mass spectrometry data: specifically the identification of phyllosilicates and carbonates. However, Wild 2 dust was collected via impact into capture media at ~6 km s?1, leading to uncertainty as to whether these minerals were captured intact, and, if subjected to alteration, whether they remain recognizable. We simulated Stardust Al foil capture conditions using a two‐stage light‐gas gun, and directly compared transmission electron microscope analyses of pre‐ and postimpact samples to investigate survivability of lizardite and cronstedtite (phyllosilicates) and calcite (carbonate). We find the phyllosilicates do not survive impact as intact crystalline materials but as moderately to highly vesiculated amorphous residues lining resultant impact craters, whose bulk cation to Si ratios remain close to that of the impacting grain. Closer inspection reveals variation in these elements on a submicron scale, where impact‐induced melting accompanied by reducing conditions (due to the production of oxygen scavenging molten Al from the target foils) has resulted in the production of native silicon and Fe‐ and Fe‐Si‐rich phases. In contrast, large areas of crystalline calcite are preserved within the calcite residue, with smaller regions of vesiculated, Al‐bearing calcic glass. Unambiguous identification of calcite impactors on Stardust Al foil is therefore possible, while phyllosilicate impactors may be inferred from vesiculated residues with appropriate bulk cation to Si ratios. Finally, we demonstrate that the characteristic textures and elemental distributions identifying phyllosilicates and carbonates by transmission electron microscopy can also be observed by state‐of‐the‐art scanning electron microscopy providing rapid, nondestructive initial mineral identifications in Stardust residues.  相似文献   

4.
Aerogel collectors have been deployed in low-Earth orbit to collect orbital debris and micrometeorites. An array of silica aerogel collectors is currently en-route back to Earth following an encounter with the Comet Wild-2 on board the Stardust spacecraft. Stardust is returning, for laboratory analysis, cometary and interstellar dust grains which impacted into the aerogel collectors at hypervelocities. While the morphology of impact craters in aerogels has been studied empirically, a theoretical understanding of the physical mechanisms responsible for the formation of impact craters in these solids is lacking. Here we propose and test a model of compaction driven impact cratering in aerogels. Our model derives impact crater dimensions directly from energy and momentum deposition.  相似文献   

5.
The interstellar collector on NASA's Stardust mission captured many particles from sources other than the interstellar dust stream. Impact trajectory may provide a means of discriminating between these different sources, and thus identifying/eliminating candidate interstellar particles. The collector's aerogel preserved a clear record of particle impact trajectory from the inclination and direction of the resultant tracks. However, the collector also contained aluminum foils and, although impact crater studies to date suggest only the most inclined impacts (>45° from normal) produce crater morphologies that indicate trajectory (i.e., distinctly elliptical), these studies have been restricted to much larger (mm and above) scales than are relevant for Stardust (μm). It is unknown how oblique impact crater morphology varies as a function of length scale, and therefore how well Stardust craters preserve details of impactor trajectory. Here, we present data from a series of impact experiments, together with complementary hydrocode modeling, that examine how crater morphology changes with impact angles for different‐sized projectiles. We find that, for our smallest spherical projectiles (2 μm diameter), the ellipticity and rim morphology provide evidence of their inclined trajectory from as little as 15° from normal incidence. This is most likely a result of strain rate hardening in the target metal. Further experiments and models find that variation in velocity and impactor shape complicate these trends, but that rim morphology remains useful in determining impact direction (where the angle of impact is >20° from normal) and may help identify candidate interstellar particle craters on the Stardust collector.  相似文献   

6.
Abstract– Samples returned by the Stardust mission from comet 81P/Wild 2 provide an unequaled opportunity to investigate cometary formation and evolution. Crystalline silicates have been identified in impact craters in Stardust Al foil, yet their origin is ambiguous. They may be original cometary components, or they may have grown from melt generated by impact. We have now studied experimental impacts of the calcium silicate mineral wollastonite, using scanning and transmission electron microscopy to document the relationship between impact feature shape and crystal lattice orientation in impact residue. Wollastonite can have a characteristic acicular habit, forming crater shapes that indicate crystal orientation upon impact. From extracted impact residue, we determined the lattice orientation of crystalline material for comparison with the whole particle orientation. We assume that crystallization from melt, without surviving seed nuclei, should result in randomly oriented crystallite growth, with no preferred direction for individual crystals. However, we find that the majority of crystalline material in the residue retains b‐axis orientation parallel to the long axis of the crater form. This, together with impact parameter calculations and lack of Al incorporation by the residue (suggesting melting did not occur), indicates that these crystals and, by analogy, the majority of Al‐free crystalline silicates in Stardust foil, are surviving remnants of the impactor. Furthermore, amorphous wollastonite residue probably did not form via melting and subsequent quenching, but instead by high‐pressure amorphization or degradation of unquenchable phases. Finally, one crystal studied appears to be a new high‐pressure/temperature polymorph of CaSiO3, indicating that such polymorphs may be observed in Stardust residues in craters.  相似文献   

7.
Abstract— The known encounter velocity (6.1 kms?1) and particle incidence angle (perpendicular) between the Stardust spacecraft and the dust emanating from the nucleus of comet Wild‐2 fall within a range that allows simulation in laboratory light‐gas gun (LGG) experiments designed to validate analytical methods for the interpretation of dust impacts on the aluminum foil components of the Stardust collector. Buckshot of a wide size, shape, and density range of mineral, glass, polymer, and metal grains, have been fired to impact perpendicularly on samples of Stardust Al 1100 foil, tightly wrapped onto aluminum alloy plate as an analogue of foil on the spacecraft collector. We have not yet been able to produce laboratory impacts by projectiles with weak and porous aggregate structure, as may occur in some cometary dust grains. In this report we present information on crater gross morphology and its dependence on particle size and density, the pre‐existing major‐ and trace‐element composition of the foil, geometrical issues for energy dispersive X‐ray analysis of the impact residues in scanning electron microscopes, and the modification of dust chemical composition during creation of impact craters as revealed by analytical transmission electron microscopy. Together, these observations help to underpin the interpretation of size, density, and composition for particles impacted on the Stardust aluminum foils.  相似文献   

8.
Abstract— Metallic aluminum alloy foils exposed on the forward, comet‐facing surface of the aerogel tray on the Stardust spacecraft are likely to have been impacted by the same cometary particle population as the dedicated impact sensors and the aerogel collector. The ability of soft aluminum alloy to record hypervelocity impacts as bowl‐shaped craters offers an opportunistic substrate for recognition of impacts by particles of a potentially wide size range. In contrast to impact surveys conducted on samples from low Earth orbit, the simple encounter geometry for Stardust and Wild‐2, with a known and constant spacecraft‐particle relative velocity and effective surface‐perpendicular impact trajectories, permits closely comparable simulation in laboratory experiments. For a detailed calibration program, we have selected a suite of spherical glass projectiles of uniform density and hardness characteristics, with well‐documented particle size range from 10 μm to nearly 100 μm. Light gas gun buckshot firings of these particles at approximately 6 km s?1 onto samples of the same foil as employed on Stardust have yielded large numbers of craters. Scanning electron microscopy of both projectiles and impact features has allowed construction of a calibration plot, showing a linear relationship between impacting particle size and impact crater diameter. The close match between our experimental conditions and the Stardust mission encounter parameters should provide another opportunity to measure particle size distributions and fluxes close to the nucleus of Wild‐2, independent of the active impact detector instruments aboard the Stardust spacecraft.  相似文献   

9.
We present results of FIB–TEM studies of 12 Stardust analog Al foil craters which were created by firing refractory Si and Ti carbide and nitride grains into Al foils at 6.05 km s?1 with a light‐gas gun to simulate capture of cometary grains by the Stardust mission. These foils were prepared primarily to understand the low presolar grain abundances (both SiC and silicates) measured by SIMS in Stardust Al foil samples. Our results demonstrate the intact survival of submicron SiC, TiC, TiN, and less‐refractory Si3N4 grains. In small (<2 μm) craters that are formed by single grain impacts, the entire impacting crystalline grain is often preserved intact with minimal modification. While they also survive in crystalline form, grains at the bottom of larger craters (>5 μm) are typically fragmented and are somewhat flattened in the direction of impact due to partial melting and/or plastic deformation. The low presolar grain abundance estimates derived from SIMS measurements of large craters (mostly >50 μm) likely result from greater modification of these impactors (i.e., melting and isotopic dilution), due to higher peak temperatures/pressures in these crater impacts. The better survivability of grains in smaller craters suggests that more accurate presolar grain estimates may be achievable through measurement of such craters. It also suggests small craters can provide a complementary method of study of the Wild 2 fine fraction, especially for refractory CAI‐like minerals.  相似文献   

10.
The Stardust mission returned two types of unprecedented extraterrestrial samples: the first samples of material from a known solar system body beyond the moon, the comet 81P/Wild2, and the first samples of contemporary interstellar dust. Both sets of samples were captured in aerogel and aluminum foil collectors and returned to Earth in January 2006. While the analysis of particles from comet Wild 2 yielded exciting new results, the search for and analysis of collected interstellar particles is more demanding and is ongoing.Novel dust instrumentation will tremendously improve future dust collection in interplanetary space: an Active Cosmic Dust Collector is a combination of an in-situ dust trajectory sensor (DTS) together with a dust collector consisting of aerogel and/or other collector materials, e.g. such as those used by the Stardust mission. Dust particles’ trajectories are determined by the measurement of induced electrical signals when charged particles fly through a position sensitive electrode system. The recorded waveforms enable the reconstruction of the velocity vector with high precision.The DTS described here was subject to performance tests at the Heidelberg dust accelerator at the same time as the recording of impact signals from potential collector materials. The tests with dust particles in the speed range from 3 to 40 km/s demonstrate that trajectories can be measured with accuracies of ～1° in direction and ～1% in speed. The sensitivity of the DTS electronics is of the order of 10?16 C and thus the trajectory of cosmic dust particles as small as 0.4 μm size can be measured. The impact position on the collector can be determined with better than 1 mm precision, which will ease immensely the task of locating sub-micron-sized particles on the collector. Statistically significant numbers of trajectories of interplanetary and interstellar dust particles can thus be collected in interplanetary space and their compositions correlated with their trajectories.  相似文献   

11.
Abstract– The fluence of dust particles <10 μm in diameter was recorded by impacts on aluminum foil of the NASA Stardust spacecraft during a close flyby of comet 81P/Wild 2 in 2004. Initial interpretation of craters for impactor particle dimensions and mass was based upon laboratory experimental simulations using projectiles less than >10 μm in diameter and the resulting linear relationship of projectile to crater diameter was extrapolated to smaller sizes. We now describe a new experimental calibration program firing very small monodisperse silica projectiles (470 nm–10 μm) at approximately 6 km s?1. The results show an unexpected departure from linear relationship between 1 and 10 μm. We collated crater measurement data and, where applicable, impactor residue data for 596 craters gathered during the postmission preliminary examination phase. Using the new calibration, we recalculate the size of the particle responsible for each crater and hence reinterpret the cometary dust size distribution. We find a greater flux of small particles than previously reported. From crater morphology and residue composition of a subset of craters, the internal structure and dimensions of the fine dust particles are inferred and a “maximum‐size” distribution for the subgrains composing aggregate particles is obtained. The size distribution of the small particles derived directly from the measured craters peaks at approximately 175 nm, but if this is corrected to allow for aggregate grains, the peak in subgrain sizes is at <100 nm.  相似文献   

12.
Abstract– We present NanoSIMS four‐isotope S analyses of 24 comet Wild 2 dust impact residues in craters on aluminum foil C2037N returned by NASA’s Stardust mission. Except for one sample, all impact residues have normal S isotopic compositions within 2σ uncertainties of at least two S isotope ratios. This implies that most S‐rich Wild 2 dust impactors formed in the solar system. Instrumental isotope fractionation due to sample topography is the main contribution to our analytical uncertainty. One impact crater residue shows small anomalies of δ33S = ?57 ± 17‰, and δ34S = ?41 ± 17‰ (1σ uncertainties). Although this could be simply a statistical outlier or the fingerprint of a chemical isotope fractionation it is also possible that the observed anomaly results from the mixture of a cometary FeS particle with a small (150 nm diam.) presolar FeS supernova grain. This would translate into a presolar sulfide abundance of approximately 200 ppm.  相似文献   

13.
Abstract— Various microscopic techniques were used to characterize experimental microcraters in aluminum foils to prepare for the comprehensive analysis of the cometary and interstellar particle impacts in aluminum foils to be returned by the Stardust mission. First, scanning electron microscopy (SEM) and energy dispersive X‐ray spectroscopy (EDS) were used to study the morphology of the impact craters and the bulk composition of the residues left by soda‐lime glass impactors. A more detailed structural and compositional study of impactor remnants was then performed using transmission electron microscopy (TEM), EDS, and electron diffraction methods. The TEM samples were prepared by focused ion beam (FIB) methods. This technique proved to be especially valuable in studying impact crater residues and impact crater morphology. Finally, we also showed that infrared microscopy (IR) can be a quick and reliable tool for such investigations. The combination of all of these tools enables a complete microscopic characterization of the craters.  相似文献   

14.
Abstract— The Stardust sample return capsule returned to Earth in January 2006 with primitive debris collected from comet 81P/Wild‐2 during the flyby encounter in 2004. In addition to the cometary particles embedded in low‐density silica aerogel, there are microcraters preserved in the aluminum foils (1100 series; 100 μm thick) that are wrapped around the sample tray assembly. Soda lime spheres (?49 μm in diameter) have been accelerated with a light gas gun into flight‐grade aluminum foils at 6.35 km s?1 to simulate the capture of cometary debris. The experimental craters have been analyzed using scanning electron microscopy (SEM) and X‐ray energy dispersive spectroscopy (EDX) to locate and characterize remants of the projectile material remaining within the craters. In addition, ion beam‐induced secondary electron imaging has proven particularly useful in identifying areas within the craters that contain residue material. Finally, high‐precision focused ion beam (FIB) milling has been used to isolate and then extract an individual melt residue droplet from the interior wall of an impact. This has enabled further detailed elemental characterization that is free from the background contamination of the aluminum foil substrate. The ability to recover “pure” melt residues using FIB will significantly extend the interpretations of the residue chemistry preserved in the aluminum foils returned by Stardust.  相似文献   

15.
Abstract– We present initial results from hydrocode modeling of impacts on Al‐1100 foils, undertaken to aid the interstellar preliminary examination (ISPE) phase for the NASA Stardust mission interstellar dust collector tray. We used Ansys’ AUTODYN to model impacts of micrometer‐scale, and smaller projectiles onto Stardust foil (100 μm thick Al‐1100) at velocities up to 300 km s?1. It is thought that impacts onto the interstellar dust collector foils may have been made by a combination of interstellar dust particles (ISP), interplanetary dust particles (IDP) on comet, and asteroid derived orbits, β micrometeoroids, nanometer dust in the solar wind, and spacecraft derived secondary ejecta. The characteristic velocity of the potential impactors thus ranges from <<1 to a few km s?1 (secondary ejecta), approximately 4–25 km s?1 for ISP and IDP, up to hundreds of km s?1 for the nanoscale dust reported by Meyer‐Vernet et al. (2009) . There are currently no extensive experimental calibrations for the higher velocity conditions, and the main focus of this work was therefore to use hydrocode models to investigate the morphometry of impact craters, as a means to determine an approximate impactor speed, and thus origin. The model was validated against existing experimental data for impact speeds up to approximately 30 km s?1 for particles ranging in density from 2.4 kg m?3 (glass) to 7.8 kg m?3 (iron). Interpolation equations are given to predict the crater depth and diameter for a solid impactor with any diameter between 100 nm and 4 μm and density between 2.4 and 7.8 kg m?3.  相似文献   

16.
Abstract— New experimental results show that Stardust crater morphology is consistent with interpretation of many larger Wild 2 dust grains being aggregates, albeit most of low porosity and therefore relatively high density. The majority of large Stardust grains (i.e. those carrying most of the cometary dust mass) probably had density of 2.4 g cm?3 (similar to soda‐lime glass used in earlier calibration experiments) or greater, and porosity of 25% or less, akin to consolidated carbonaceous chondrite meteorites, and much lower than the 80% suggested for fractal dust aggregates. Although better size calibration is required for interpretation of the very smallest impacting grains, we suggest that aggregates could have dense components dominated by μm‐scale and smaller sub‐grains. If porosity of the Wild 2 nucleus is high, with similar bulk density to other comets, much of the pore space may be at a scale of tens of micrometers, between coarser, denser grains. Successful demonstration of aggregate projectile impacts in the laboratory now opens the possibility of experiments to further constrain the conditions for creation of bulbous (Type C) tracks in aerogel, which we have observed in recent shots. We are also using mixed mineral aggregates to document differential survival of pristine composition and crystalline structure in diverse finegrained components of aggregate cometary dust analogues, impacted onto both foil and aerogel under Stardust encounter conditions.  相似文献   

17.
Abstract— In January 2006, NASA's Stardust mission will return with its valuable cargo of the first cometary dust particles captured at hypervelocity speeds in silica aerogel collectors and brought back to Earth. Aerogel, a proven capture medium, is also a candidate for future sample return missions and low‐Earth orbit (LEO) deployments. Critical to the science return of Stardust as well as future missions that will use aerogel is the ability to efficiently extract impacted particles from collector tiles. Researchers will be eager to obtain Stardust samples as quickly as possible; tools for the rapid extraction of particle impact tracks that require little construction, training, or investment would be an attractive asset. To this end, we have experimented with diamond and steel microblades. Applying ultrasonic frequency oscillations to these microblades via a piezo‐driven holder produces rapid, clean cuts in the aerogel with minimal damage to the surrounding collector tile. With this approach, intact impact tracks and associated particles in aerogel fragments with low‐roughness cut surfaces have been extracted from aerogel tiles flown on NASA's Orbital Debris Collector (ODC) experiment. The smooth surfaces produced during cutting reduce imaging artifacts during analysis by scanning electron microscopy (SEM). Some tracks have been dissected to expose the main cavity for eventual isolation of individual impact debris particles and further analysis using techniques such as transmission electron microscopy (TEM) and nano‐secondary ion mass spectrometry (nanoSIMS).  相似文献   

18.
The Lonar impact crater, India, is one of the few known terrestrial impact craters excavated in continental basaltic target rocks (Deccan Traps, ~65 Ma). The impactites reported from the crater to date mainly include centimeter‐ to decimeter‐sized impact‐melt bombs, and aerodynamically shaped millimeter‐ and submillimeter‐sized impact spherules. They occur in situ within the ejecta around the crater rim and show schlieren structure. In contrast, non–in situ glassy objects, loosely strewn around the crater lake and in the ejecta around the crater rim do not show any schlieren structure. These non–in situ fragments appear to be similar to ancient bricks from the Daityasudan temple in the Lonar village. Synthesis of existing and new major and trace element data on the Lonar impact spherules show that (1) the target Lonar basalts incorporated into the spherules had undergone minimal preimpact alteration. Also, the paleosol layer as preserved between the top‐most target basalt flow and the ejecta blanket, even after the impact, was not a source component for the Lonar impactites, (2) the Archean basement below the Deccan traps were unlikely to have contributed material to the impactite parental melts, and (3) the impactor asteroid components (Cr, Co, Ni) were concentrated only within the submillimeter‐sized spherules. Two component mixing calculations using major oxides and Cr, Co, and Ni suggest that the Lonar impactor was a EH‐type chondrite with the submillimeter‐sized spherules containing ~6 wt% impactor components.  相似文献   

19.
In 2006, NASA's Stardust spacecraft delivered to Earth dust particles collected from the coma of comet 81P/Wild 2, with the goal of furthering the understanding of solar system formation. Stardust cometary samples were collected in a low‐density, nanoporous silica aerogel making their study technically challenging. This article demonstrates the identification, exposure, and elemental composition analysis of particles analogous to those collected by NASA's Stardust mission using in‐situ SEM techniques. Backscattered electron imaging is shown by experimental observation and Monte Carlo simulation to be suitable for locating particles of a range of sizes relevant to Stardust (down to submicron diameters) embedded within silica aerogel. Selective removal of the silica aerogel encapsulating an embedded particle is performed by cryogenic NF3‐mediated electron beam–induced etching. The porous, low‐density nature of the aerogel results in an enhanced etch rate compared with solid material, making it an effective, nonmechanical method for the exposure of particles. After exposure, elemental composition of the particle was analyzed by energy‐dispersive X‐ray spectroscopy using a high spectral resolution microcalorimeter. Signals from fluorine contamination are shown to correspond to nonremoved silica aerogel and only in residual concentrations.  相似文献   

20.
Abstract— New model organic microparticles are used to assess the thermal ablation that occurs during aerogel capture at speeds from 1 to 6 km s?1. Commercial polystyrene particles (20 μm diameter) were coated with an ultrathin 20 nm overlayer of an organic conducting polymer, polypyrrole. This overlayer comprises only 0.8% by mass of the projectile but has a very strong Raman signature, hence its survival or destruction is a sensitive measure of the extent of chemical degradation suffered. After aerogel capture, microparticles were located via optical microscopy and their composition was analyzed in situ using Raman microscopy. The ultrathin polypyrrole overlayer survived essentially intact for impacts at ～1 km s?1, but significant surface carbonization was found at 2 km s?1, and major particle mass loss at ≥3 km s?1. Particles impacting at ～6.1 km s?1 (the speed at which cometary dust was collected in the NASA Stardust mission) were reduced to approximately half their original diameter during aerogel capture (i.e., a mass loss of 84%). Thus significant thermal ablation occurs at speeds above a few km s?1. This suggests that during the Stardust mission the thermal history of the terminal dust grains during capture in aerogel may be sufficient to cause significant processing or loss of organic materials. Further, while Raman D and G bands of carbon can be obtained from captured grains, they may well reflect the thermal processing during capture rather than the pre‐impact particle's thermal history.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号