首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 484 毫秒
1.
Delivery of sulfate to petroleum hydrocarbons (PHCs) source zones and groundwater plumes is desirable to enhance biodegradation rates when treatment has become limited due to depletion of sulfate. Sulfate land application involves spreading sulfate salts on ground surface and allowing their dissolution and infiltration of sulfate into subsurface. The objectives of this pilot-scale investigation were to capture the vertical transport of sulfate beneath an application area, confirm that sulfate reduction was occurring, and explore how the added sulfate affected biodegradation of benzene and toluene. Approximately 4000 kg of gypsum was spread over a 30 m × 30 m study area above a smear zone located approximately 2 m below-ground surface. Precipitation was augmented by two irrigation events. Groundwater samples, collected over 1058 days from multilevel wells and a conventional long-screened monitoring well, were analyzed for benzene, toluene, ethylbenzene, and xylenes (BTEX), sulfate, bromide, dissolved inorganic carbon (DIC) and methane. Compound-specific isotope analyses (CSIA) for benzene and toluene, and isotope analyses of 13C-DIC and 34S-SO42− were performed. Following application, an increase in sulfate concentration was noted in the smear zone. 34S-SO42− enrichment and 13C-DIC depletion indicated that sulfate reduction and mineralization of PHCs were enhanced. CSIA results provided unequivocal evidence of anaerobic biodegradation of benzene and toluene. After 1058 days when sulfate was depleted, methane concentrations were about three times greater than baseline conditions suggesting syntrophic benefit of the delivered sulfate. Observations from this investigation support the viability of sulfate land application to enhance biodegradation rates in shallow PHC smear zones.  相似文献   

2.
  相似文献   

3.
At a service station closed in 1993, groundwater contained benzene that persisted above the cleanup goal of 1 mg/L in zones depleted of background sulfate. The benzene and other petroleum hydrocarbons (PHCs) were present as much as 36 feet (11 m) below the water table and therefore remediation of a thick saturated zone interval was required. Microcosms using site sediments demonstrated that anaerobic benzene biodegradation occurred only if sulfate was added, suggesting sulfate addition as a remediation approach. Twenty-four boreholes (9.1″ diameter and 56′ deep) were drilled around four monitoring wells, in which benzene concentrations exceeded 1 mg/L. The boreholes were backfilled with a mixture of gravel and 15,000 pounds of gypsum (which releases sulfate as it dissolves) to create “Permeable Filled Borings” (PFBs). Concurrently, nine high pressure injections (HPIs) of gypsum slurry were conducted in other site locations (312 pounds of gypsum total). PFBs were expected to release sulfate for up to 20 years, whereas HPIs were expected to produce a short-lived plume of sulfate. Concentrations of benzene and sulfate in groundwater were monitored over a 3-year period in six monitoring wells. In two wells near PFBs, benzene concentrations dropped below the cleanup goal by two to three orders of magnitude; in one well, sulfate concentrations exceeded 500 mg/L for the most recent 18 months. Benzene concentrations in two other PFB monitoring wells declined by a factor of 2 to 4, but remained above 1 mg/L, presumably due to high-dissolved PHC concentrations and possibly greater residual PHC mass in adjacent sediments, and therefore greater sulfate demand. However, hydrogen and sulfur isotopic enrichment in benzene and sulfate, respectively, confirmed biodegradation of benzene and stimulation of sulfate-reducing conditions. Thus, it is hypothesized that the PHC mass in adjacent sediments will decline over time, as will dissolved PHC concentrations, and eventually benzene concentrations will decrease below the cleanup goal. Benzene in two HPI monitoring wells was below the cleanup goal for all but one sampling event before HPIs were conducted and remained below the cleanup goal after HPIs; there was no stimulation of sulfate-reducing conditions. It is concluded that sulfate released from PFBs contributed to declining benzene concentrations.  相似文献   

4.
Monitored natural attenuation is widely applied as a remediation strategy at hydrocarbon spill sites. Natural attenuation relies on biodegradation of hydrocarbons coupled with reduction of electron acceptors, including solid phase ferric iron (Fe(III)). Because arsenic (As) adsorbs to Fe‐hydroxides, a potential secondary effect of natural attenuation of hydrocarbons coupled with Fe(III) reduction is a release of naturally occurring As to groundwater. At a crude‐oil‐contaminated aquifer near Bemidji, Minnesota, anaerobic biodegradation of hydrocarbons coupled to Fe(III) reduction has been well documented. We collected groundwater samples at the site annually from 2009 to 2013 to examine if As is released to groundwater and, if so, to document relationships between As and Fe inside and outside of the dissolved hydrocarbon plume. Arsenic concentrations in groundwater in the plume reached 230 µg/L, whereas groundwater outside the plume contained less than 5 µg/L As. Combined with previous data from the Bemidji site, our results suggest that (1) naturally occurring As is associated with Fe‐hydroxides present in the glacially derived aquifer sediments; (2) introduction of hydrocarbons results in reduction of Fe‐hydroxides, releasing As and Fe to groundwater; (3) at the leading edge of the plume, As and Fe are removed from groundwater and retained on sediments; and (4) downgradient from the plume, patterns of As and Fe in groundwater are similar to background. We develop a conceptual model of secondary As release due to natural attenuation of hydrocarbons that can be applied to other sites where an influx of biodegradable organic carbon promotes Fe(III) reduction.  相似文献   

5.
The fate of hydrocarbons in the subsurface near Bemidji, Minnesota, has been investigated by a multidisciplinary group of scientists for over a quarter century. Research at Bemidji has involved extensive investigations of multiphase flow and transport, volatilization, dissolution, geochemical interactions, microbial populations, and biodegradation with the goal of providing an improved understanding of the natural processes limiting the extent of hydrocarbon contamination. A considerable volume of oil remains in the subsurface today despite 30 years of natural attenuation and 5 years of pump‐and‐skim remediation. Studies at Bemidji were among the first to document the importance of anaerobic biodegradation processes for hydrocarbon removal and remediation by natural attenuation. Spatial variability of hydraulic properties was observed to influence subsurface oil and water flow, vapor diffusion, and the progression of biodegradation. Pore‐scale capillary pressure‐saturation hysteresis and the presence of fine‐grained sediments impeded oil flow, causing entrapment and relatively large residual oil saturations. Hydrocarbon attenuation and plume extent was a function of groundwater flow, compound‐specific volatilization, dissolution and biodegradation rates, and availability of electron acceptors. Simulation of hydrocarbon fate and transport affirmed concepts developed from field observations, and provided estimates of field‐scale reaction rates and hydrocarbon mass balance. Long‐term field studies at Bemidji have illustrated that the fate of hydrocarbons evolves with time, and a snap‐shot study of a hydrocarbon plume may not provide information that is of relevance to the long‐term behavior of the plume during natural attenuation.  相似文献   

6.
A field study of oxygen-enhanced biodegradation was carried out in a sandy iron-rich ground water system contaminated with gasoline hydrocarbons. Prior to the oxygen study, intrinsic microbial biodegradation in the contaminant plume had depleted dissolved oxygen and created anaerobic conditions. An oxygen diffusion system made of silicone polymer tubing was installed in an injection well within an oxygen delivery zone containing coarse highly permeable sand. During the study, this system delivered high dissolved oxygen (DO) levels (39 mg/L) to the ground water within a part of the plume. The ground water was sampled at a series of monitors in the test zone downgradient of the delivery well to determine the effect of oxygen on dissolved BTEX, ground water geochemistry, and microbially mediated biodegradation processes. The DO levels and Eh increased markedly at distances up to 2.3 m (7.5 feet) downgradient. Potential biofouling and iron precipitation effects did not clog the well screens or porous medium. The increased dissolved oxygen enhanced the population of aerobes while the activity of anaerobic sulfate-reducing bacteria and methanogens decreased. Based on concentration changes, the estimated total rate of BTEX biodegradation rose from 872 mg/day before enhancement to 2530 mg/day after 60 days of oxygen delivery. Increased oxygen flux to the test area could account for aerobic biodegradation of 1835 mg/day of the BTEX. The estimated rates of anaerobic biodegradation processes decreased based on the flux of sulfate, iron (II), and methane. Two contaminants in the plume, benzene and ethylbenzene, are not biodegraded as readily as toluene or xylenes under anaerobic conditions. Following oxygen enhancement, however, the benzene and ethylbenzene concentrations decreased about 98%, as did toluene and total xylenes.  相似文献   

7.
Selection of monitored natural attenuation as a ground water remedy requires that sound scientific documentation clearly illustrating the effectiveness of this remedial alternative be presented to regulatory agencies and concerned citizens. An innovative radial diagram approach is applied to illustrate natural attenuation trends for total benzene, toluene, ethylbenzene, and xylenes (BTEX) and chlorinated ethenes at a former fire training area at Pittsburgh Air Force Base, New York. A BTEX-CAH (chlorinated aliphatic hydrocarbons) radial diagram map shows that concentrations of site contaminants are generally decreasing along the primary flowpath downgradient from the source area. This radial diagram map also suggests that there is a spatial correlation between decreasing CAH parent compound concentrations and increasing or stable daughter product concentrations. This provides secondary evidence of intrinsic biodegradation of TCE downgradient from the source area. A SEQUENCE-Redox™ map suggests that there is a spatial correlation between trends in electron acceptor and metabolic byproduct concentrations, and the decline in total BTEX concentrations downgradient from the source area. This correlation provides secondary evidence for the intrinsic biodegradation of total BTEX in the aquifer. This study demonstrates that radial diagram visual aids can provide a clear and efficient approach for documenting natural attenuation lines of evidence, as an alternative or a complement to using multiple contour maps, tabulated data, or log-linear plots.  相似文献   

8.
The effectiveness of different remediation procedures for decreasing the amount of TPH (total petroleum hydrocarbons) in contaminated groundwater was evaluated at the site of a former refinery. The investigations were carried out on samples taken from several gravel based HSSF (horizontal subsurface flow) constructed wetlands (CW) which differed in relation to their filter material additives (no additive, charcoal, and ferric oxides additives) and examined the potential effect of these additives on the overall treatment efficiency. Samples of the following gravel based HSSF CW were investigated. No filter additive (system A), 0.1% activated carbon (system B), 0.5% iron(III) hydroxide (system C), and the reference (system D). Systems A–C were planted with common reed (Phragmites australis), whereas system D remained unplanted. In addition, the influence of seasonal conditions on the reduction of these hydrocarbons and the correlation between the amounts of TPH and BTEX (benzene, toluene, ethylbenzene, and xylene isomers), on the one hand, and methyl tert‐butyl ether, on the other, was investigated. The study was carried out by using a modified GC‐FID approach and multivariate methods. The investigations carried out in the first year of operation demonstrated that the effectiveness of the petroleum hydrocarbon removal was highest and reached a level of 93 ± 3.5% when HSSF filters with activated carbon as a filter additive were used. This remediation method allowed the petroleum hydrocarbon content to be reduced independently of seasonal conditions. The correlation between the reduction of TPH and BTEX was found to be R = 0.8824. Using this correlation coefficient, the time‐consuming determination of the BTEX content was no longer necessary.  相似文献   

9.
Ground water scientists have made significant advances in understanding the soil interactions, hydrogeology, fate and transport, and subsurface microbiology of aromatic hydrocarbons (BTEX) in aquifer systems. It is now generally recognized that a major factor responsible for the attenuation and mass reduction of BTEX in plumes is the widespread occurrence of hydrocarbon biodegradation by indigenous soil microorganisms in aquifer material. Most well-studied BTEX plumes that develop from the accidental release of gasoline fuels contain low levels of soluble hydrocarbons (< 1 to 5000 ppb) and have been shown to be spatially confined because of natural biotransformation mechanisms. These in situ processes are controlled by source and aquifer characteristics, permeability, sorption, and geochemical properties of the aquifer. Many laboratory subsoil-ground water microcosms and field studies (10 to 20 C) have demonstrated the rapid biodecay (1 to SO percent/day for microcosms and 0.5 to 1.5 percent/day for plumes) of these aromatic compounds under primarily aerobic conditions (i.e., those with sufficient dissolved oxygen). The ability to implement ground water bioremediation will depend upon our understanding of source control and aquifer recharge effects on the spatial distribution of plumes. In addition, estimating the biodegradation of sorbed BTEX, determining limits and potential for in situ biostimulation of soluble plumes, and establishing data requirements for predictive modeling of natural attenuation will be useful for this remediation technology. The use of these tools to manage ground water quality appears to represent the most practical alternative, particularly for low-risk ground water supplies.  相似文献   

10.
Geochemical Indicators of Intrinsic Bioremediation   总被引：19，自引：0，他引：19  
A detailed field investigation has been completed at a gasoline-contaminated aquifer near Rocky Point, NC, to examine possible indicators of intrinsic bioremediation and identify factors that may significantly influence the rate and extent of bioremediation. The dissolved plume of benzene, toluene, ethylbenzene, and xylene (BTEX) in ground water is naturally degrading. Toluene and o-xylene are most rapidly degraded followed by m-, p-xylene, and benzene. Ethylbenzene appears to degrade very slowly under anaerobic conditions present in the center of the plume. The rate and extent of biodegradation appears to be strongly influenced by the type and quantity of electron acceptors present in the aquifer. At the upgradient edge of the plume, nitrate, ferric iron, and oxygen are used as terminal electron acceptors during hydrocarbon biodegradation. The equivalent of 40 to 50 mg/I of hydrocarbon is degraded based on the increase in dissolved CO2 relative to background ground water. Immediately downgradient of the source area, sulfate and iron are the dominant electron acceptors. Toluene and o-xylene are rapidly removed in this region. Once the available oxygen, nitrate, and sulfate are consumed, biodegradation is limited and appears to be controlled by mixing and aerobic biodegradation at the plume fringes.  相似文献   

11.
Evaluation of BTEX Remediation by Natural Attenuation at a Coastal Facility   总被引：1，自引：0，他引：1  
Natural attenuation has emerged as a potential alternative for remediating sites contaminated with fuel hydrocarbons. This paper examines the viability of using attenuation through natural processes to remediate ground water at an industrial facility. The research combined field assessments with data analysis and modeling to evaluate plume stability and predict remediation times. Field data on natural attenuation indicate that BTEX contamination at the site is being attenuated at rates that vary within the range of 0.0001 to 0.0073/day. Stability analyses confirm that the BTEX plume has reached steady state. An analysis on mass flux showed that between 1979 and 1996, 95,000 pounds of BTEX were lost via biodegradation, while 8000 pounds were lost through other mechanisms. A first-order biodegradation rate of 0.0002/day for BTEX was obtained from the change in the total mass of dissolved BTEX with time. Cleanup times in excess of 200 years for the site were estimated using analytical modeling of natural attenuation, which agreed well with the remediation times estimated using the attenuation rates calculated for the site.  相似文献   

12.
A numerical study was conducted to investigate the influence of tides on the fate of terrestrially derived BTEX discharging through an unconfined aquifer to coastal waters. Previous studies have revealed that tide-induced seawater circulations create an active salt–freshwater mixing zone in the near-shore aquifer and alter the specific subsurface pathway for contaminants discharging to the coastal environment. Here the coupled density-dependent flow and multi-species reactive transport code PHWAT was used to examine the impact of these tidal effects on the aerobic biodegradation of BTEX released in a coastal aquifer and its subsequent loading to coastal waters. Simulations indicated that tides significantly enhance BTEX attenuation in the near-shore aquifer. They also reduce the rate of chemical transfer from the aquifer to the ocean and exit concentrations at the beach face. For the base case consisting of toluene transport and biodegradation, 79% of toluene initially released in the aquifer was attenuated prior to discharge with tides present, compared to only 1.8% for the non-tidal case. The magnitude of tidal forcing relative to the fresh groundwater flow rate was shown to influence significantly the extent of biodegradation as it controls the intensity of salt–freshwater mixing, period of exposure of the contaminant to the mixing zone and rate of oxygen delivery to the aquifer. The oxygen available for biodegradation also depends on the rate at which oxygen is consumed by natural processes such as organic matter decomposition. While simulations conducted with heterogeneous conductivity fields highlighted the uncertainties associated with predicting contaminant loadings, the study revealed overall that BTEX may undergo significant attenuation in tidally influenced aquifers prior to discharge.  相似文献   

13.
Hydrocarbon contamination of lakes and rivers from subsurface discharge of ground-water is a common environmental problem in many countries. This source of contamination, particularly dissolved phase hydrocarbons, can significantly reduce the quality of natural waters. Laboratory results show that the aqueous solubility of benzene can be predicted by Raoul''s Law for BTEX mixtures and for gas condensate. In contrast, the solubility of total xylenes was up to three times higher than the calculated results using Raoul''s Law. A comparison of these finding with the composition of BTEX in groundwater at a sour-gas plant, indicated that the mole fraction and groundwater flow velocity were two principle factors affecting the discharge concentration of benzene and xylenes to natural waters.  相似文献   

14.
A detailed seasonal study of soil vapor intrusion at a cold climate site with average yearly temperature of 1.9 °C was conducted at a house with a crawlspace that overlay a shallow dissolved‐phase petroleum hydrocarbon (gasoline) plume in North Battleford, Saskatchewan, Canada. This research was conducted primarily to assess if winter conditions, including snow/frost cover, and cold soil temperatures, influence aerobic biodegradation of petroleum vapors in soil and the potential for vapor intrusion. Continuous time‐series data for oxygen, pressure differentials, soil temperature, soil moisture, and weather conditions were collected from a high‐resolution monitoring network. Seasonal monitoring of groundwater, soil vapor, crawlspace air, and indoor air was also undertaken. Petroleum hydrocarbon vapor attenuation and biodegradation rates were not significantly reduced during low temperature winter months and there was no evidence for a significant capping effect of snow or frost cover that would limit oxygen ingress from the atmosphere. In the residual light nonaqueous phase liquid (LNAPL) source area adjacent to the house, evidence for biodegradation included rapid attenuation of hydrocarbon vapor concentrations over a vertical interval of approximately 0.9 m, and a corresponding decrease in oxygen to less than 1.5% v/v. In comparison, hydrocarbon vapor concentrations above the dissolved plume and below the house were much lower and decreased sharply within a few tens of centimeters above the groundwater source. Corresponding oxygen concentrations in soil gas were at least 10% v/v. A reactive transport model (MIN3P‐DUSTY) was initially calibrated to data from vertical profiles at the site to obtain biodegradation rates, and then used to simulate the observed soil vapor distribution. The calibrated model indicated that soil vapor transport was dominated by diffusion and aerobic biodegradation, and that crawlspace pressures and soil gas advection had little influence on soil vapor concentrations.  相似文献   

15.
The feasibility of surface application for remediating monoaromatic hydrocarbons (benzene, toluene, ethylbenzene, and xylenes — termed BTEX as a croup) dissolved in ground water under field conditions was investigated at a site within Canadian Forces Base. Borden. Ontario. The surface area was 25 m2 and underlain by 3 to 3.5 m of unsaturated sands soil. For periods of at least 216 hours, between 43 and 72 cm/d of water containing BTEX at concentrations that averaged between 8 and 11 mg/L were continuously applied by drip irrigation. Nitrogen was added to the soil as a nutrient for the final third of the investigation.
Before the applied water reached the water table. BTEX mass losses ranged from of to essentially KM) percent. Less than 6 percent of the BTEX mass losses could be attributed to volatilization from the unsaturated soil. The remaining BTEX mass losses were attributed to biodegradation, mostly in the top 50 cm of the soil, which contained more inorganic nitrogen and organic carbon than the deeper soil. Biodegradation rates increased with applied concentration, nitrogen addition, and exposure to BTEX. Benzene concentrations in ground water attained compliance with Canadian and American drinking water standards only after nitrogen application.  相似文献   

16.
Quantifying the overall progress in remediation of contaminated groundwater has been a significant challenge. We utilized the GeoTracker database to evaluate the progress in groundwater remediation from 2001 to 2011 at over 12,000 sites in California with contaminated groundwater. This paper presents an analysis of analytical results from over 2.1 million groundwater samples representing at least $100 million in laboratory analytical costs. Overall, the evaluation of monitoring data shows a large decrease in groundwater concentrations of gasoline constituents. For benzene, half of the sites showed a decrease in concentration of 85% or more. For methyl tert‐butyl ether (MTBE), this decrease was 96% and for TBE, 87%. At remediation sites in California, the median source attenuation rate was 0.18/year for benzene and 0.36/year for MTBE, corresponding to half‐lives of 3.9 and 1.9 years, respectively. Attenuation rates were positive (i.e., decreasing concentration) for benzene at 76% of sites and for MTBE at 85% of sites. An evaluation of sites with active remediation technologies suggests differences in technology effectiveness. The median attenuation rates for benzene and MTBE are higher at sites with soil vapor extraction or air sparging compared with sites without these technologies. In contrast, there was little difference in attenuation rates at sites with or without soil excavation, dual phase extraction, or in situ enhanced biodegradation. The evaluation of remediation technologies, however, did not evaluate whether specific systems were well designed or implemented and did not control for potential differences in other site factors, such as soil type.  相似文献   

17.
Since the 1990s, questions have arisen as to whether the release of ethanol‐blended fuel will inhibit natural attenuation of other gasoline constituents in groundwater. This study evaluated the hypothesis that ethanol affects hydrocarbon attenuation and whether the use of ethanol‐blended fuel alters the applicability of monitored natural attenuation (MNA) as an approach for managing risks at fuel‐release sites. Groundwater data from California's GeoTracker database were used to compare attenuation of benzene, toluene, methyl tert‐butyl ether (MTBE), and tert‐butyl alcohol (TBA) at sites with and without detections of ethanol. Excel‐based tools were developed to conduct attenuation evaluations on thousands of wells simultaneously. Ethanol was detected at least once in 4.5% of the wells and 0.6% of the samples of which it was analyzed. The distribution of Mann‐Kendall concentration trend analysis results and first‐order attenuation rates were essentially the same at sites with or without ethanol detections. Median plume lengths were shorter at sites where ethanol had not been detected compared to sites where ethanol was detected (36 vs. 43 m for benzene; 36 vs. 42 m for toluene; 43 vs. 52 m for MTBE; and 44 vs. 59 m for TBA). However, the distribution of plume lengths was similar irrespective of ethanol concentrations, suggesting other factors may influence plume elongation. Finally, while anaerobic ethanol degradation can result in methane generation, the distributions of methane concentrations were the same at sites with and without ethanol detections. These results suggest that the use of ethanol‐blended fuel should not limit the application of MNA at most biodegrading fuel‐release sites.  相似文献   

18.
The temperature sensitivity of microbial populations is reflected in measured source attenuation rates at hydrocarbon‐impacted sites. The objective of this study was to evaluate the correlation between temperature and source attenuation rates (concentration vs. time attenuation rate over many years) of benzene and toluene by analyzing groundwater monitoring data from >2000 hydrocarbon sites. Historical monitoring records were obtained from three databases, processed to yield long‐term multiyear source attenuation rates, and then compared with representative temperatures at each site. Statistically significant and positive relationships between temperature and source attenuation rates were established for benzene and toluene, indicating that temperature does impact hydrocarbon degradation, but is one of many factors that contribute to source attenuation. There was an observed 1.1 to 1.6 times increase in attenuation rates per 10 °C increase in temperature, which is less than the rate increases predicted by the Arrhenius equation. The temperature dependence on attenuation rate is consistent with several lines of evidence that methanogenesis plays a key role in the rate of hydrocarbon source zone attenuation rather than being controlled strictly by the availability of electron acceptors. First, methanogenesis is known to be strongly influenced by temperature, with significantly higher rates up to about 35 °C. Second, the temperature‐degradation rate relationship was stronger at sites with deeper water tables (>30 ft) that are less susceptible to oxygen influx than sites with shallow water tables (<15 ft). Third, dissolved methane concentrations were higher at sites with warmer temperatures. Overall, these results provide indirect support for a conceptual model where methanogenesis is a key degradation process at hydrocarbon sites, and that attenuation of these source zones is temperature‐sensitive.  相似文献   

19.
Consumption of aquifer Fe(III) during biodegradation of ground water contaminants may result in expansion of a contaminant plume, changing the outlook for monitored natural attenuation. Data from two research sites contaminated with petroleum hydrocarbons show that toluene and xylenes degrade under methanogenic conditions, but the benzene and ethylbenzene plumes grow as aquifer Fe(III) supplies are depleted. By considering a one-dimensional reaction front in a constant unidirectional flow field, it is possible to derive a simple expression for the growth rate of a benzene plume. The method balances the mass flux of benzene with the Fe(III) content of the aquifer, assuming that the biodegradation reaction is instantaneous. The resulting expression shows that the benzene front migration is retarded relative to the ground water velocity by a factor that depends on the concentrations of hydrocarbon and bioavailable Fe(III). The method provides good agreement with benzene plumes at a crude oil study site in Minnesota and a gasoline site in South Carolina. Compared to the South Carolina site, the Minnesota site has 25% higher benzene flux but eight times the Fe(III), leading to about one-sixth the expansion rate. Although it was developed for benzene, toluene, ethylbenzene, and xylenes, the growth-rate estimation method may have applications to contaminant plumes from other persistent contaminant sources.  相似文献   

20.
Pseudomonas putida MHF 7109 has been isolated and identified from cow dung microbial consortium for biodegradation of selected petroleum hydrocarbon compounds – benzene, toluene, and o‐xylene (BTX). Each compound was applied separately at concentrations of 50, 100, 250, and 500 mg L?1 in minimal salt medium to evaluate degradation activity of the identified microbial strain. The results indicated that the strain used has high potential to degrade BTX at a concentration of 50 mg L?1 within a period of 48, 96, and 168 h, respectively; whereas the concentration of 100 mg L?1 of benzene and toluene was found to be completely degraded within 120 and 168 h, respectively. Sixty‐two percent of o‐xylene were degraded within 168 h at the 100 mg L?1 concentration level. The maximum degradation rates for BTX were 1.35, 1.04, and 0.51 mg L?1 h?1, respectively. At higher concentrations (250 and 500 mg L?1) BTX inhibited the activity of microorganisms. The mass spectrometry analysis identified the intermediates as catechol, 2‐hydroxymuconic semialdehyde, 3‐methylcatechol, cis‐2‐hydroxypenta‐2,4‐dienoate, 2‐methylbenzyl alcohol, and 1,2‐dihydroxy‐6‐methylcyclohexa‐3,5‐dienecarboxylate, for BTX, respectively. P. putida MHF 7109 has been found to have high potential for biodegradation of volatile petroleum hydrocarbons.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号