共查询到20条相似文献，搜索用时 31 毫秒
1.
Flow from some springs in former glacial lakebeds of the Upper Midwest is extremely steady throughout the year and does not increase significantly after precipitation events or seasonal recharge. Analytical and simplified numerical models of spring systems were used to determine whether preferential ground water flow through high-permeability features in shallow sandstone aquifers could produce typical values of spring discharge and the unusually steady rates of spring flow. The analytical model is based on a one-dimensional solution for periodic ground water flow. Solutions to this model suggest that it is unlikely that a periodic forcing due to seasonal variations in areal recharge would propagate to springs in a setting where high-permeability features exist. The analytical model shows that the effective length of the aquifer, or the length of flowpaths to a spring, and the total transmissivity of the aquifer have the greatest potential to impact the nature of spring flow in this setting. The numerical models show that high-permeability features can influence the magnitude of spring flow and the results demonstrate that the lengths of ground water flowpaths increase when high-permeability features are explicitly modeled, thus decreasing the likelihood for temporal variations in spring flow. 相似文献
2.
Design Screening Tools for Passive Funnel and Gate Systems 总被引：1，自引：0，他引：1
Robert A. Sedivy John M. Shafer Lacrecia C. Bilbrey 《Ground Water Monitoring & Remediation》1999,19(1):125-133
The funnel and gate remediation concept (Star and Cherry 1993) represents a promising, yet relatively under-developed, technology for the passive control and in situ remediation of contaminated ground water. Effective design and implementation of such a system may, however, prove difficult under conditions of large or unpredictable variations in contaminant migration or ground water flow.
Numerical modeling of two-dimensional ground water flow has been used to predict the hydraulic performance of passive, straight, or winged funnel and gate configurations over a range of hydrogeologic and ambient ground water flow conditions. The results of these analyses were used to construct generic correlation diagrams relating upstream capture zone or gale through put to the barrier, gale, and aquifer characteristics. These diagrams serve as useful screening tools to (1) quantitatively estimate the capture zone of pre-determined funnel and gale configurations, or (2) develop preliminary funnel and gale designs that will yield a desired capture zone, independent of aquifer characteristics. 相似文献
Numerical modeling of two-dimensional ground water flow has been used to predict the hydraulic performance of passive, straight, or winged funnel and gate configurations over a range of hydrogeologic and ambient ground water flow conditions. The results of these analyses were used to construct generic correlation diagrams relating upstream capture zone or gale through put to the barrier, gale, and aquifer characteristics. These diagrams serve as useful screening tools to (1) quantitatively estimate the capture zone of pre-determined funnel and gale configurations, or (2) develop preliminary funnel and gale designs that will yield a desired capture zone, independent of aquifer characteristics. 相似文献
3.
Reactive barriers are passive and in situ ground water treatment systems. Heterogeneities in hydraulic conductivity (K) within the aquifer-reactive barrier system will result in higher flux rates, and reduced residence times, through portions of the barrier. These spatial variations in residence time will affect the treatment capacity of the barrier. A numerical flow model was used to evaluate the effects of spatial variations in K on preferential flow through barriers. The simulations indicate that the impact of heterogeneities in K will be a function of their location and distribution; the more localized the high K zone, the greater the preferential flow. The geometry of the reactive barrier will also strongly influence flow distribution. Aquifer heterogeneities will produce greater preferential flow in thinner barriers compared to thicker barriers. If the barrier K is heterogeneous, greater preferential flow will occur in thicker barriers. The K of the barrier will affect the flow distribution; decreasing the K of the barrier can result in more even distribution of flow. Results indicate that less variable flow will be attained utilizing thicker, homogeneous barriers. The addition of homogeneous zones to thinner barriers will be effective at redistributing flow only if installed immediately adjacent to both the up- and downgradient faces of the barrier. 相似文献
4.
This article analyzes part of a ground water flow system in the North China Plain (NCP) subject to severe overexploitation and rapid depletion. A transient ground water flow model was constructed and calibrated to quantify the changes in the flow system since the predevelopment 1950s. The flow model was then used in conjunction with an optimization code to determine optimal pumping schemes that improve ground water management practices. Finally, two management scenarios, namely, urbanization and the South-to-North Water Transfer Project, were evaluated for their potential impacts on the ground water resources in the study area. Although this study focuses on the NCP, it illustrates a general modeling framework for analyzing the sustainability, or the lack thereof, of ground water flow systems driven by similar hydrogeologic and economic conditions. The numerical simulation is capable of quantifying the various components of the overall flow budget and evaluating the impacts of different management scenarios. The optimization modeling allows the determination of the maximum "sustainable pumping" that satisfies a series of prescribed constraints. It can also be used to minimize the economic costs associated with ground water development and management. Furthermore, since the NCP is one of the most water scarce and economically active regions in the world, the conclusions and insights from this study are of general interest and international significance. 相似文献
5.
Recharge areas of spring systems can be hard to identify, but they can be critically important for protection of a spring resource. A recharge area for a spring complex in southern Wisconsin was delineated using a variety of complementary techniques. A telescopic mesh refinement (TMR) model was constructed from an existing regional-scale ground water flow model. This TMR model was formally optimized using parameter estimation techniques; the optimized "best fit" to measured heads and fluxes was obtained by using a horizontal hydraulic conductivity 200% larger than the original regional model for the upper bedrock aquifer and 80% smaller for the lower bedrock aquifer. The uncertainty in hydraulic conductivity was formally considered using a stochastic Monte Carlo approach. Two-hundred model runs used uniformly distributed, randomly sampled, horizontal hydraulic conductivity values within the range given by the TMR optimized values and the previously constructed regional model. A probability distribution of particles captured by the spring, or a "probabilistic capture zone," was calculated from the realistic Monte Carlo results (136 runs of 200). In addition to portions of the local surface watershed, the capture zone encompassed areas outside of the watershed--demonstrating that the ground watershed and surface watershed do not coincide. Analysis of water collected from the site identified relatively large contrasts in chemistry, even for springs within 15 m of one another. The differences showed a distinct gradation from Ordovician-carbonate-dominated water in western spring vents to Cambrian-sandstone-influenced water in eastern spring vents. The difference in chemistry was attributed to distinctive bedrock geology as demonstrated by overlaying the capture zone derived from numerical modeling over a bedrock geology map for the area. This finding gives additional confidence to the capture zone calculated by modeling. 相似文献
6.
Calculation of ground water ages--a comparative analysis 总被引：1，自引：0，他引：1
Ground water age is a fundamental, yet complex, concept in ground water hydrology. Discrepancies between results obtained through different modeling approaches for ground water age calculation have been reported, in particular, between ground water ages modeled by advection and direct simulation of ground water ages (e.g., age-mass approach), which includes effects of advection and dispersion. Here, through a series of two-dimensional (2D) simulations, the impact of water mixing through advection and dispersion on modeled 14C and directly simulated ground water ages is assessed. Impact of dispersion on modeled ages is systematically stronger in areas where water velocities are smaller and far more pronounced on 14C ages. This effect is also observed in one-dimensional models. 2D simulations show that longitudinal dispersion generally acts as a "source" of 14C, while vertical dispersion acts as a "sink," leading to apparent younger or older modeled 14C ages as compared to advective and directly simulated ground water ages. The presence of permeable and impermeable faults provides an equally important source for discrepancies, leading to major differences in modeled ages among the three methods considered. Overall, our results show that a 14C modeling approach using a solute transport model for calculating ground water age appears to be more reliable in ground water systems without faults and where water velocities are relatively high than in systems that are relatively more heterogeneous and those where faults are present. Among the three modeling approaches considered here, direct simulation of ground water age seems to yield the most consistent results in complex, heterogeneous ground water flow systems, giving a vertical age structure consistent with ages expected from consideration of the flow system. 相似文献
7.
Comparative study of methods for WHPA delineation 总被引：3，自引：0，他引：3
Paradis D Martel R Karanta G Lefebvre R Michaud Y Therrien R Nastev M 《Ground water》2007,45(2):158-167
Human activities, whether agricultural, industrial, commercial, or domestic, can contribute to ground water quality deterioration. In order to protect the ground water exploited by a production well, it is essential to develop a good knowledge of the flow system and to adequately delineate the area surrounding the well within which potential contamination sources should be managed. Many methods have been developed to delineate such a wellhead protection area (WHPA). The integration of more information on the geologic and hydrogeologic characteristics of the study area increases the precision of any given WHPA delineation method. From a practical point of view, the WHPA delineation methods allowing the simplest and least expensive integration of the available information should be favored. This paper presents a comparative study in which nine different WHPA delineation methods were applied to a well and a spring in an unconfined granular aquifer and to a well in a confined highly fractured rock aquifer. These methods range from simple approaches to complex computer models. Hydrogeological mapping and numerical modeling with MODFLOW-MODPATH were used as reference methods to respectively compare the delineation of the zone of contribution and the zone of travel obtained from the various WHPA methods. Although applied to simple ground water flow systems, these methods provided a relatively wide range of results. To allow a realistic delineation of the WHPA in aquifers of variable geometry, a WHPA delineation method should ensure a water balance and include observed or calculated regional flow characteristics. 相似文献
8.
Several technologies for cleaning up DNAPLs in source zones rely on solubilizing contaminants or destroying them in situ. Typically, these approaches employ an injection/withdrawal system to recirculate this treatment fluids. Our interest is in examining factors that influence delivery efficiency. Although many factors can affect this efficiency, this study looks at the combined influence of density-driven flow and porous media heterogeneities. The analysis is based on a series of numerical simulations of hypothetical chemical floods (e.g., potassium permanganate), which are highly resolved in space and time with a scale that is typical of field installations. Results indicate that the characteristics of convective mixing, i.e., natural, forced, and mixed convection, greatly affect delivery efficiency and patterns of mass transport. The ratio of the Grashof number (Gr) and Reynolds number (Re) proved useful in interpreting the patterns of flooding in a homogeneous porous medium. When higher-permeability layers are included in the domain, they act as conduits, effectively expediting the transport of treatment chemicals from injection to recovery wells. These large fluxes of chemicals in the high-permeability layers produce significant flooding inefficiencies. The problem is less severe in heterogeneous medium where the connectivity through the treatment zone is less well developed. Overall, this paper illustrates that density effects and high-permeability pathways need to be considered in designing chemical floods. 相似文献
9.
Numerical models constitute the most advanced physical-based methods for modeling complex ground water systems. Spatial and/or temporal variability of aquifer parameters, boundary conditions, and initial conditions (for transient simulations) can be assigned across the numerical model domain. While this constitutes a powerful modeling advantage, it also presents the formidable challenge of overcoming parameter uncertainty, which, to date, has not been satisfactorily resolved, inevitably producing model prediction errors. In previous research, artificial neural networks (ANNs), developed with more accessible field data, have achieved excellent predictive accuracy over discrete stress periods at site-specific field locations in complex ground water systems. In an effort to combine the relative advantages of numerical models and ANNs, a new modeling paradigm is presented. The ANN models generate accurate predictions for a limited number of field locations. Appending them to a numerical model produces an overdetermined system of equations, which can be solved using a variety of mathematical techniques, potentially yielding more accurate numerical predictions. Mathematical theory and a simple two-dimensional example are presented to overview relevant mathematical and modeling issues. Two of the three methods for solving the overdetermined system achieved an overall improvement in numerical model accuracy for various levels of synthetic ANN errors using relatively few constrained head values (i.e., cells), which, while demonstrating promise, requires further research. This hybrid approach is not limited to ANN technology; it can be used with other approaches for improving numerical model predictions, such as regression or support vector machines (SVMs). 相似文献
10.
Laboratory and numerical investigation of flow and transport near a seepage-face boundary 总被引：3，自引：0，他引：3
Laboratory and numerical modeling investigations were completed to study the unconfined ground water flow and transport processes near a seepage-face boundary. The laboratory observations were made in a radial sand tank and included measurements of the height of the seepage face, flow velocity near the seepage face, travel time distribution of multiple tracer slugs, and streamlines. All the observations were reliably reproduced with a three-dimensional, axi-symmetric, variably saturated ground water flow model. Physical data presented in this work demonstrate and quantify the importance of three-dimensional transport patterns within a seepage-face zone. The results imply that vertically averaged flow models that employ Dupuit approximations might introduce error in the analysis of localized solute transport near a seepage-face boundary. The experimental dataset reported in this work will also be of interest for those who are attempting to validate a numerical algorithm for solving ground water and contaminant discharge patterns near a surface-water boundary. 相似文献
11.
The Application of In Situ Air Sparging as an Innovative Soils and Ground Water Remediation Technology 总被引：3，自引：0，他引：3
Michael C. Marley David J. Hazebrouck Matthew T. Walsh 《Ground Water Monitoring & Remediation》1992,12(2):137-145
Vapor extraction (soil venting) has been demonstrated to be a successful and cost-effective remediation technology for removing VOCs from the vadose (unsaturated) zone. However, in many cases, seasonal water table fluctuations, drawdown associated with pump-and-treat remediation techniques, and spills involving dense, non-aqueous phase liquids (DNAPLS) create contaminated soil below the water table. Vapor extraction alone is not considered to be an optimal remediation technology to address this type of contamination.
An innovative approach to saturated zone remediation is the use of sparging (injection) wells to inject a hydrocarbon-free gaseous medium (typically air) into the saturated zone below the areas of contamination. The contaminants dissolved in the ground water and sorbed onto soil particles partition into the advective air phase, effectively simulating an in situ air-stripping system. The stripped contaminants are transported in the gas phase to the vadose zone, within the radius of influence of a vapor extraction and vapor treatment system.
In situ air sparging is a complex multifluid phase process, which has been applied successfully in Europe since the mid-1980s. To date, site-specific pilot tests have been used to design air-sparging systems. Research is currently underway to develop better engineering design methodologies for the process. Major design parameters to be considered include contaminant type, gas injection pressures and flow rates, site geology, bubble size, injection interval (areal and vertical) and the equipment specifications. Correct design and operation of this technology has been demonstrated to achieve ground water cleanup of VOC contamination to low part-per-billion levels. 相似文献
An innovative approach to saturated zone remediation is the use of sparging (injection) wells to inject a hydrocarbon-free gaseous medium (typically air) into the saturated zone below the areas of contamination. The contaminants dissolved in the ground water and sorbed onto soil particles partition into the advective air phase, effectively simulating an in situ air-stripping system. The stripped contaminants are transported in the gas phase to the vadose zone, within the radius of influence of a vapor extraction and vapor treatment system.
In situ air sparging is a complex multifluid phase process, which has been applied successfully in Europe since the mid-1980s. To date, site-specific pilot tests have been used to design air-sparging systems. Research is currently underway to develop better engineering design methodologies for the process. Major design parameters to be considered include contaminant type, gas injection pressures and flow rates, site geology, bubble size, injection interval (areal and vertical) and the equipment specifications. Correct design and operation of this technology has been demonstrated to achieve ground water cleanup of VOC contamination to low part-per-billion levels. 相似文献
12.
The funnel-and-gate ground water remediation technology (Starr and Cherry 1994) has received increased attention and application as an in situ alternative to the typical pump-and-treat system. Understanding the effects of heterogeneity on system performance can mean the difference between a successful remediation project and one that fails to meet its cleanup goals.
In an attempt to characterize and quantify the effects of heterogeneity on funnel-and-gate system performance, a numerical modeling study of 15 simulated heterogeneous flow domains was conducted. Each realization was tested to determine if the predicted capture width met the capture width expected for a homogeneous flow domain with the same hulk properties. This study revealed that the capture width of the funnel-and-gate system varied significantly with the level of heterogeneity of the aquifer.
Two possible remedies were investigated for bringing systems with less than acceptable capture widths to acceptable levels of performance. First, it was determined that enlarging the funnel and gate via a factor of safety applied to the design capture width could compensate for the capture width variation in the heterogeneous flow domains. In addition, it was shown that the use of a pumping well downstream of the funnel and gate could compensate for the effects of aquifer heterogeneity on the funnel-and-gate capture width. However, if a pumping well is placed downstream of the funnel and gate to control the hydraulic gradient through the gate, consideration should be given to the gate residence time in relation to the geochemistry of the contaminant removal or destruction process in the gate. 相似文献
In an attempt to characterize and quantify the effects of heterogeneity on funnel-and-gate system performance, a numerical modeling study of 15 simulated heterogeneous flow domains was conducted. Each realization was tested to determine if the predicted capture width met the capture width expected for a homogeneous flow domain with the same hulk properties. This study revealed that the capture width of the funnel-and-gate system varied significantly with the level of heterogeneity of the aquifer.
Two possible remedies were investigated for bringing systems with less than acceptable capture widths to acceptable levels of performance. First, it was determined that enlarging the funnel and gate via a factor of safety applied to the design capture width could compensate for the capture width variation in the heterogeneous flow domains. In addition, it was shown that the use of a pumping well downstream of the funnel and gate could compensate for the effects of aquifer heterogeneity on the funnel-and-gate capture width. However, if a pumping well is placed downstream of the funnel and gate to control the hydraulic gradient through the gate, consideration should be given to the gate residence time in relation to the geochemistry of the contaminant removal or destruction process in the gate. 相似文献
13.
The role of hand calculations in ground water flow modeling 总被引：1，自引：0，他引：1
Haitjema H 《Ground water》2006,44(6):786-791
Most ground water modeling courses focus on the use of computer models and pay little or no attention to traditional analytic solutions to ground water flow problems. This shift in education seems logical. Why waste time to learn about the method of images, or why study analytic solutions to one-dimensional or radial flow problems? Computer models solve much more realistic problems and offer sophisticated graphical output, such as contour plots of potentiometric levels and ground water path lines. However, analytic solutions to elementary ground water flow problems do have something to offer over computer models: insight. For instance, an analytic one-dimensional or radial flow solution, in terms of a mathematical expression, may reveal which parameters affect the success of calibrating a computer model and what to expect when changing parameter values. Similarly, solutions for periodic forcing of one-dimensional or radial flow systems have resulted in a simple decision criterion to assess whether or not transient flow modeling is needed. Basic water balance calculations may offer a useful check on computer-generated capture zones for wellhead protection or aquifer remediation. An easily calculated "characteristic leakage length" provides critical insight into surface water and ground water interactions and flow in multi-aquifer systems. The list goes on. Familiarity with elementary analytic solutions and the capability of performing some simple hand calculations can promote appropriate (computer) modeling techniques, avoids unnecessary complexity, improves reliability, and is likely to save time and money. Training in basic hand calculations should be an important part of the curriculum of ground water modeling courses. 相似文献
14.
In a recent field study of ground water/surface water interaction between a bedrock stream and an underlying fractured rock aquifer, it was determined that the majority of ground water discharge occurred through sparsely located vertical fractures. In this paper, the dominant mechanisms governing ground water/surface water exchange in such an environment are investigated using a numerical model. The study was conducted using several conceptual models based on the field study results. Although the field results provided the motivation for the modeling study, it was not intended to match modeling and field results directly. In addition, the extent of capture zones for discharging or recharging fractures was explored. The results of this study are intended to provide a better understanding of contaminant migration in the vicinity of bedrock streams. Based on the numerical results, the rate of ground water discharge (or recharge) was found to depend on the aperture size of the discharging feature, and on the distribution of hydraulic head with depth within the fracture network. It was determined that the extent of both the capture zone and reverse capture zone for an individual fracture can be extremely large, and will be determined by the height of the stream stage, the fracture apertures of the network, and the hydraulic-head distribution within the network. Because both the stream stage and the hydraulic-head distribution are transient, the size of the capture zone and/or the reverse capture zone for an individual fracture may change significantly over time. As a result, the migration path for contaminants within the fracture network and between the surface and subsurface will also vary significantly with time. 相似文献
15.
Discharges of polluted water from abandoned mines are a major cause of degradation of water resources worldwide. Pollution arises after abandoned workings flood up to surface level, by the process termed ground water rebound. As flow in large, open mine voids is often turbulent, standard techniques for modeling ground water flow (which assume laminar flow) are inappropriate for predicting ground water rebound. More physically realistic models are therefore desirable, yet these are often expensive to apply to all but the smallest of systems. An overall strategy for ground water rebound modeling is proposed, with models of decreasing complexity applied as the temporal and spatial scales of the systems under analysis increase. For relatively modest systems (area < 200 km2), a physically based modeling approach has been developed, in which 3-D pipe networks (representing major mine roadways, etc.) are routed through a variably saturated, 3-D porous medium (representing the country rock). For systems extending more than 100 to 3000 km2, a semidistributed model (GRAM) has been developed, which conceptualizes extensively interconnected volumes of workings as ponds, which are connected to other ponds only at discrete overflow points, such as major inter-mine roadways, through which flow can be efficiently modeled using the Prandtl-Nikuradse pipe-flow formulation. At the very largest scales, simple water-balance calculations are probably as useful as any other approach, and a variety of proprietary codes may be used for the purpose. 相似文献
16.
Thomas C. Winter Donald C. Buso Patricia C. Shattuck Phillip T. Harte Donald A. Vroblesky Daniel J. Goode 《水文研究》2008,22(1):21-32
The west watershed of Mirror Lake in the White Mountains of New Hampshire contains several terraces that are at different altitudes and have different geologic compositions. The lowest terrace (FSE) has 5 m of sand overlying 9 m of till. The two next successively higher terraces (FS2 and FS1) consist entirely of sand and have maximum thicknesses of about 7 m. A fourth, and highest, terrace (FS3) lies in the north‐west watershed directly adjacent to the west watershed. This highest terrace has 2 m of sand overlying 8 m of till. All terraces overlie fractured crystalline bedrock. Numerical models of hypothetical settings simulating ground‐water flow in a mountainside indicated that the presence of a terrace can cause local ground‐water flow cells to develop, and that the flow patterns differ based on the geologic composition of the terrace. For example, more ground water moves from the bedrock to the glacial deposits beneath terraces consisting completely of sand than beneath terraces that have sand underlain by till. Field data from Mirror Lake watersheds corroborate the numerical experiments. The geology of the terraces also affects how the stream draining the west watershed interacts with ground water. The stream turns part way down the mountainside and passes between the two sand terraces, essentially transecting the movement of ground water down the valley side. Transects of water‐table wells were installed across the stream's riparian zone above, between, and below the sand terraces. Head data from these wells indicated that the stream gains ground water on both sides above and below the sand terraces. However, where it flows between the sand terraces the stream gains ground water on its uphill side and loses water on its downhill side. Biogeochemical processes in the riparian zone of the flow‐through reach have resulted in anoxic ground water beneath the lower sand terrace. Results of this study indicate that it is useful to understand patterns of ground‐water flow in order to fully understand the flow and chemical characteristics of both ground water and surface water in mountainous terrain. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
17.
The concept of vulnerability of drinking water sources is reviewed, and a quantitative approach for assessing well vulnerability for complex three-dimensional ground water systems is developed. The approach focuses on the relative expected impact of potential contaminant sources at unknown locations within a well capture zone, providing relative measures of intrinsic well vulnerability, including the expected times of arrival of a contaminant, the dispersion-related reduction in concentration, the time taken to breach a certain quality objective, and the corresponding exposure times. Thus, the result of the analysis includes the usual advective travel time information used in conventional wellhead protection analysis, plus a set of selected quantitative measures expressing the expected impact. The technique is based on adjoint theory and combines forward- and backward-in-time transport modeling using a standard numerical flow and transport code. The methodology is demonstrated using the case study of a complex glacial multiaquifer system in Ontario. The new approach will be useful in helping water managers develop more physically based and quantitative wellhead protection strategies. 相似文献
18.
The permeability of the Elkhorn fault zone,South Park,Colorado 总被引：5，自引：0，他引：5
The purposes of this study are to use both field and modeling approaches to characterize the permeability of a fault and to assess the role of the fault on regional ground water flow. The study subject is the Elkhorn fault, a low-angle reverse fault that brings Precambrian crystalline rocks over the sediments of Colorado's South Park Basin. The fault is hypothesized to act as a low-permeability barrier to flow, restricting interaction between the crystalline aquifer and the basin sediments. To test this hypothesis and to better predict the permeability structure of the fault, we synthesized geologic data to create a geologic model of the fault, conducted aquifer tests to estimate the hydrogeologic properties of the fault zone, and used ground water modeling to test the influence of a range of hydraulic properties for the fault zone on ground water flow in the region. Our study suggests that the fault is a low-permeability feature. Estimated heads are best matched to observations by modeling the fault as a 10-foot-thick interval of low-permeability fault gouge. Steady-state flow models show that much of the flow in the study area is topographically driven near land surface. Flow rates decrease with depth in the aquifers. In the footwall, ground water moves updip in the Michigan-San Isabel syncline to discharge in the South Park Basin. In the hanging wall, ground water moves east to a regional ground water divide. Sensitivity analyses indicate that hydraulic heads are most sensitive to changes in hydraulic conductivity and recharge. 相似文献
19.
In Situ Biorestoration as a Ground Water Remediation Technique 总被引：1，自引：0，他引：1
John T Wilson Lowell E. Leach Michael Henson Jerry N. Jones 《Ground Water Monitoring & Remediation》1986,6(4):56-64
In situ biorestoration, where applicable, is indicated as a potentially very cost-effective and environmentally acceptable remediation technology. Many contaminants in solution in ground water as well as vapors in the unsaturated zone can be completely degraded or transformed into new compounds by naturally occurring indigenous microbial populations. Undoubtedly, thousands of contamination events are remediated naturally before the contamination reaches a point of detection. The need is for methodology to determine when natural biorestoration is occurring, the stage the restoration process is in, whether enhancement of the process is possible or desirable, and what will happen if natural processes are allowed to run their course.
In addition to the nature of the contaminant, several environmental factors are known to influence the capacity of indigenous microbial populations to degrade contaminants. These factors include dissolved oxygen, pH, temperature, oxidation-reduction potential, availability of mineral nutrients, salinity, soil moisture, the concentration of specific pollutants, and the nutritional quality of dissolved organic carbon in the ground water.
Most enhanced in situ bioreclamation techniques available today are variations of hydrocarbon degradation procedures pioneered and patented by Raymond and coworkers at Suntech during the period 1974 to 1978. Nutrients and oxygen are introduced through injection wells and circulated through the contaminated zone by pumping one or more producing wells.
The limiting factor in remediation technology is getting the contaminated subsurface material to the treatment unit or units, or in the case of in situ processes, getting the treatment process to the contaminated material. The key to successful remediation is a thorough understanding of the hydrogeologic and geochemical characteristics of the contaminated area. 相似文献
In addition to the nature of the contaminant, several environmental factors are known to influence the capacity of indigenous microbial populations to degrade contaminants. These factors include dissolved oxygen, pH, temperature, oxidation-reduction potential, availability of mineral nutrients, salinity, soil moisture, the concentration of specific pollutants, and the nutritional quality of dissolved organic carbon in the ground water.
Most enhanced in situ bioreclamation techniques available today are variations of hydrocarbon degradation procedures pioneered and patented by Raymond and coworkers at Suntech during the period 1974 to 1978. Nutrients and oxygen are introduced through injection wells and circulated through the contaminated zone by pumping one or more producing wells.
The limiting factor in remediation technology is getting the contaminated subsurface material to the treatment unit or units, or in the case of in situ processes, getting the treatment process to the contaminated material. The key to successful remediation is a thorough understanding of the hydrogeologic and geochemical characteristics of the contaminated area. 相似文献
20.
Allogenic karst systems function in a particular way that is influenced by the type of water infiltrating through river water losses, by karstification processes, and by water quality. Management of this system requires a good knowledge of its structure and functioning, for which a new methodology based on an inverse modeling approach appears to be well suited. This approach requires both spring and river inflow discharge measurements and a continuous record of chemical parameters in the river and at the spring. The inverse model calculates unit hydrographs and the impulse responses of fluxes from rainfall hydraulic head at the spring or rainfall flux data, the purpose of which is hydrograph separation. Hydrograph reconstruction is done using rainfall and river inflow data as model input and enables definition at each time step of the ratio of each component. Using chemical data, representing event and pre-event water, as input, it is possible to determine the origin of spring water (either fast flow through the epikarstic zone or slow flow through the saturated zone). This study made it possible to improve a conceptual model of allogenic karst system functioning. The methodology is used to study the Bas-Agly and the Cent Font karst systems, two allogenic karst systems in Southern France. 相似文献