共查询到20条相似文献，搜索用时 109 毫秒
1.
磁流变阻尼器对高层建筑风振反应的半主动控制 总被引：21，自引：3，他引：21
本文探讨了磁流变阻尼器在高层建筑风振控制中的应用，在经典线性最优控制理论的基础上，根据磁流变阻尼器的特点，提出了一种新型的半主动控制策略，应有该方法对一40层的钢结构的风振反应进行了计算机模拟，结果表明，采用磁流变阻尼器对高层建筑进行半主动控制的能够有效减小结构的风振反应。 相似文献
2.
本文提出一种新的航电设备减振控制策略,采用半主动磁流变阻尼器与小阻尼柔性橡胶支座来取代目前采用高阻尼刚性橡胶支座的方法,以降低对航电设备的耐振要求,增强飞机飞行的安全性。本文建立了航电设备减振控制的两自由度刚体平-扭耦联模型,荷载激励考虑了基底平动与转动加速度。磁流变阻尼器的半主动控制算法选用限幅最优控制算法,主控制器为H2/LQG控制器,并采用一种加速度反馈的控制策略。针对目前的被动控制方案,本文研究了支座阻尼对减振控制效果的影响。为了得到最优的半主动控制效果,本文对控制器的权矩阵进行了参数优化分析。文中针对一系列工况详细比较了本文所提出的半主动控制策略与目前被动控制策略的减振控制效果。仿真分析结果表明,磁流变阻尼器可以非常有效地减小航电设备的动力反应,新的减振控制策略远优于现有的被动控制方案。 相似文献
3.
基于加速度反馈的结构地震反应半主动MR阻尼控制试验 总被引：11，自引：1，他引：11
本文针对安装有半主动磁流变阻尼器（MR damper)的一座二层模型结构进行了抗震振动台试验研究，通过采用基于加速度反馈控制策略的两种半主动控制算法进行了在各种地震动作用下模型结构的半主动控制的抗震试验研究，并进行了Passive-on和Passive-off两种被动控制的试验研究。试验结果表明，MR阻尼器作为一种半主动控制装置可以有效地控制结构的峰值位移和均方差反应，且半主动控制对结构顶层的峰值位移和均方差的控制效果均优于两种被动控制方法。因此，本文提出的两种半主动控制算法都是有效的，并宜于实现。 相似文献
4.
基于H∞理论的磁流变阻尼器半主动容错控制 总被引：1，自引：0，他引：1
建筑结构的半主动控制系统中的传感器,在强震作用下可能因出现故障而影响控制效果。以磁流变阻尼器为例,研究半主动容错控制系统的设计方法。首先,研究了基于状态观测器的半主动H∞控制器设计方法,并将之应用到建筑结构采用磁流变阻尼器的减振控制中;运用改进Bouc-Wen模型,计算磁流变阻尼器的阻尼力,通过求解一个代数Riccati方程和一个状态观测方程,得出了基于状态观测器的H∞主动控制律;再对其采用Clipped-optimal方法实施半主动控制策略。然后,针对传感器故障,利用观测器组的输出残差对故障进行在线诊断,并通过几个观测器状态值的比较得到故障的大小,并据此对传感器的测量值进行修正,从而消除故障对闭环系统的影响,最终实现半主动H∞容错控制。仿真结果表明,该方法具有很好的容错控制效果。 相似文献
5.
6.
多维地震作用下偏心结构的磁流变阻尼器半主动控制 总被引：9，自引：1，他引：8
理论研究与震害经验表明,地震时结构会产生不可忽略的平动与扭转耦合的空间振动。本文提出了基于线性最优控制理论的部分状态反馈次优控制策略和基于遗传算法的控制策略,以Marlab和Simulink为平台,采用磁流变阻尼器对双向水平地震作用下的偏心结构平．扭耦联反应进行半主动控制。对-6层双向偏心框架结构进行控制效果仿真分析的结果证明,本文提出的2种控制策略是有效的。 相似文献
7.
8.
9.
给出了地震动行波输入下大跨刚构连续桥梁的半主动控制分析方法，在桥梁支座部位设置磁流变阻尼器，对一座五跨刚构连续桥梁进行了不同视波速行波输入下的半主动控制计算分析. 结果表明，行波效应对该大跨刚构连续桥梁的无控制地震反应、半主动控制地震反应和减震效果均有显著影响，对主梁和桥墩均会在较低视波速地震行波输入时表现出不利影响，并且使半主动控制减震效果明显降低. 因此，在确定半主动控制系统的参数时应考虑地震行波效应的影响以确保控震效果. 相似文献
10.
结构磁流变阻尼半主动控制的改进算法与仿真分析 总被引：19，自引：0，他引：19
基于线性二次型最优控制理论,结合磁流变阻尼器装置的出力特点,提出了结构磁流变阻尼半主动控制的两种改进算法：以速度负反馈渐进逼近主动最优的界限滑动半主动控制算法和基于结构响应状态组合反馈的界限开关半主动控制算法。首先给出了采用磁流变阻尼器装置控制结构振动的系统框图,然后结合一个三层Benchmark模型,仿真分析其在多种地震输入工况下,LQR、磁流变阻尼两种半自动和两种被动控制下的控制效果,最后给出了Benchmark评价指标。 相似文献
11.
Large‐scale real‐time hybrid simulation of a three‐story steel frame building with magneto‐rheological dampers 
下载免费PDF全文
下载免费PDF全文 A series of large‐scale real‐time hybrid simulations (RTHSs) are conducted on a 0.6‐scale 3‐story steel frame building with magneto‐rheological (MR) dampers. The lateral force resisting system of the prototype building for the study consists of moment resisting frames and damped brace frames (DBFs). The experimental substructure for the RTHS is the DBF with the MR dampers, whereas the remaining structural components of the building including the moment resisting frame and gravity frames are modeled via a nonlinear analytical substructure. Performing RTHS with an experimental substructure that consists of the complete DBF enables the effects of member and connection component deformations on system and damper performance to be accurately accounted for. Data from these tests enable numerical simulation models to be calibrated, provide an understanding and validation of the in‐situ performance of MR dampers, and a means of experimentally validating performance‐based seismic design procedures for real structures. The details of the RTHS procedure are given, including the test setup, the integration algorithm, and actuator control. The results from a series of RTHS are presented that includes actuator control, damper behavior, and the structural response for different MR control laws. The use of the MR dampers is experimentally demonstrated to reduce the response of the structure to strong ground motions. Comparisons of the RTHS results are made with numerical simulations. Based on the results of the study, it is concluded that RTHS can be conducted on realistic structural systems with dampers to enable advancements in resilient earthquake resistant design to be achieved. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
12.
This paper proposes a hybrid control strategy combining passive and semi‐active control systems for seismic protection of cable‐stayed bridges. The efficacy of this control strategy is verified by examining the ASCE first‐generation benchmark problem for a seismically excited cable‐stayed bridge, which employs a three‐dimensional linearized evaluation bridge model as a testbed structure. Herein, conventional lead–rubber bearings are introduced as base isolation devices, and semi‐active dampers (e.g., variable orifice damper, controllable fluid damper, etc.) are considered as supplemental damping devices. For the semi‐active dampers, a clipped‐optimal control algorithm, shown to perform well in previous studies involving controllable dampers, is considered. Because the semi‐active damper is a controllable energy‐dissipation device that cannot add mechanical energy to the structural system, the proposed hybrid control strategy is fail‐safe in that the bounded‐input, bounded‐output stability of the controlled structure is guaranteed. Numerical simulation results show that the performance of the proposed hybrid control strategy is quite effective in protecting seismically excited cable‐stayed bridges. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
13.
Wind turbine technology is well known around the globe as an eco-friendly and effective renewable power source. However, this technology often faces reliability problems due to structural vibration. This study proposes a smart semi-active vibration control system using Magnetorheological (MR) dampers where feedback controllers are optimized with nature-inspired algorithms. Proportional integral derivative (PID) and Proportional integral (PI) controllers are designed to achieve the optimal desired force and current input for MR the damper. PID control parameters are optimized using an Ant colony optimization (ACO) algorithm. The effectiveness of the ACO algorithm is validated by comparing its performance with Ziegler-Nichols (Z-N) and particle swarm optimization (PSO). The placement of the MR damper on the tower is also investigated to ensure structural balance and optimal desired force from the MR damper. The simulation results show that the proposed semi-active PID-ACO control strategy can significantly reduce vibration on the wind turbine tower under different frequencies (i.e., 67%, 73%, 79% and 34.4% at 2 Hz, 3 Hz, 4.6 Hz and 6 Hz, respectively) and amplitudes (i.e. 50%, 58% and 67% for 50 N, 80 N, and 100 N, respectively). In this study, the simulation model is validated with an experimental study in terms of natural frequency, mode shape and uncontrolled response at the 1st mode. The proposed PID-ACO control strategy and optimal MR damper position is also implemented on a lab-scaled wind turbine tower model. The results show that the vibration reduction rate is 66% and 73% in the experimental and simulation study, respectively, at the 1st mode.
相似文献14.
Real‐time hybrid testing is a very effective technique for evaluating the dynamic responses of rate‐dependent structural systems subjected to earthquake excitation. A smart base isolation system has been proposed by others using conventional low‐damping isolators and controllable damping devices such as magnetorheological (MR) dampers to achieve specified control target performance. In this paper, real‐time hybrid tests of a smart base isolation system are conducted. The simulation is for a base‐isolated two‐degrees‐of‐freedom building model where the superstructure and the low‐damping base isolator are numerically simulated, and the MR damper is physically tested. The target displacement obtained from the step‐by‐step integration of the numerical substructure is imposed on the MR damper, which is driven by three different control algorithms in real‐time. To compensate the actuator delay and improve the accuracy of the test, an adaptive phase‐lead compensator is implemented. The accuracy of each test is investigated by using the root mean square error and the tracking indicator. Experimental results demonstrate that the hybrid testing procedure using the proposed actuator compensation techniques is effective for investigating the control performance of the MR damper in a smart base isolation system. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
15.
神经网络半主动TLCD对偏心结构的减震控制 总被引：5，自引：0，他引：5
本文采用在结构水平双向设置TLCD半主动控制装置的方法，对偏心结构在多维地震作用下的振动控制问题进行研究。首先利用多层前向神经网络，对偏心结构在双向地震输入下的两个平动方向的反应进行预测，然后在建立起半主动控制策略的基础上，利用神经网络根据控制准则调整TLCD的开孔率，实现以结构的半主动控制，数值结构表明，这种方法能对结构的平动反应和扭转反应都能起到的较好的减震效果。 相似文献
16.
为改善近断层地震动作用下隔震桥梁结构的抗震性能,基于Benchmark结构振动控制问题,研究附加黏滞阻尼器、磁流变(MR)阻尼器的组合隔震策略.非线性动力分析过程中,优化了黏滞阻尼器的阻尼系数和速度指数,并设计了分散模糊控制器来确定施加给磁流变阻尼器的电压.研究结果表明:采用黏滞阻尼器和磁流变阻尼器可提高隔震桥梁结构在... 相似文献
17.
针对巨-子结构隔震体系，在隔震层处或子结构顶部与主结构连接处，施加SMA-压电智能复合阻尼器，从而形成巨-子结构智能隔震体系。本文通过限界Hrovat最优控制算法设计了巨-子结构智能隔震体系的半主动控制器，在此基础上，对巨-子结构智能隔震体系进行了Simulink控制效果仿真分析，同时比较了控制装置安装位置的不同对结构控制效果的影响，并与普通隔震结构的减震效果进行了对比。研究结果表明，智能隔震控制1（隔震层加控制装置）和智能隔震控制2（子结构顶部加控制装置）2种控制方案在控制结构的位移方面效果相差不大。总体而言，智能隔震控制2对于控制子结构单元顶部的绝对加速度效果更为显著，但是相对于普通隔震而言，特别是在控制隔震层位移方面2种方案都具有较好的控制效果。实施智能控制可以有效改善巨-子结构被动控制体系的抗震性能，并能降低隔震结构在遭受强震时由于隔震层出现过大位移导致结构倾覆的危险。 相似文献
18.
Neuro-fuzzy control strategy for earthquake-excited nonlinear magnetorheological structures 总被引：2，自引：0，他引：2
Magnetorheological (MR) damper is a prominent semi-active control device for earthquake responses mitigation of structures. The most important topic for the intelligent MR structures is choosing the control current of MR dampers quickly and accurately. The typical control strategy is on–off control strategy, i.e. bi-state control strategy, while inherent time-delay and coarse control precision lie in this strategy. This paper proposes neuro-fuzzy control strategy, in which the neural-network technique is adopted to solve time-delay problem and the fuzzy controller is used to determine the control current of MR dampers quickly and accurately. Through comparison between the bi-state control and the neuro-fuzzy control strategies and a numerical example about a three-story reinforced concrete structure, it can be concluded that the control strategy is very important for semi-active control, the neuro-fuzzy control strategy can determine currents of MR dampers quickly and accurately, and the control effect of the neuro-fuzzy control strategy is better than that of the bi-state control strategy. 相似文献
19.
Structural vibration control using active or passive control strategy is a viable technology for enhancing structural functionality and safety against natural hazards such as strong earthquakes and high wind gusts. Both the active and passive control systems have their limitations. The passive control system has limited capability to control the structural response whereas the active control system depends on external power. The power requirement for active control of civil engineering structures is usually quite high. Thus, a hybrid control system is a viable solution to alleviate some of the limitations. In this paper a multi‐objective optimal design of a hybrid control system for seismically excited building structures has been proposed. A tuned mass damper (TMD) and an active mass driver (AMD) have been used as the passive and active control components of the hybrid control system, respectively. A fuzzy logic controller (FLC) has been used to drive the AMD as the FLC has inherent robustness and ability to handle the non‐linearities and uncertainties. The genetic algorithm has been used for the optimization of the control system. Peak acceleration and displacement responses non‐dimensionalized with respect to the uncontrolled peak acceleration and displacement responses, respectively, have been used as the two objectives of the multi‐objective optimization problem. The proposed design approach for an optimum hybrid mass damper (HMD) system, driven by FLC has been demonstrated with the help of a numerical example. It is shown that the optimum values of the design parameters of the hybrid control system can be determined without specifying the modes to be controlled. The proposed FLC driven HMD has been found to be very effective for vibration control of seismically excited buildings in comparison with the available results for the same example structure but with a different optimal absorber. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
20.
为了研究新型电磁惯性质量阻尼器(Electromagnetic Inertial Mass Damper,EIMD)应用于偏心高层结构振动控制工程的可行性,鉴于半主动控制技术的优点,基于LQR主动控制算法,提出一种可行的EIMD-偏心高层结构半主动控制策略,同时研究EIMD在结构每层中安装位置不同对于控制偏心高层结构扭转反应的影响。以一个实体24层偏心高层结构作为研究对象验证地震作用下所提控制策略的有效性,仿真结果表明:(1)所提半主动控制策略基本能够达到主动控制对于结构振动反应分量的控制效果;(2)当采用半主动控制策略时,调整EIMD的安装位置对于偏心高层结构转角和转角加速度反应有着较好的控制效果。 相似文献