共查询到20条相似文献，搜索用时 171 毫秒
1.
海岸效应对近海地区大地电磁测深数据畸变作用研究 总被引：4，自引：3，他引：1
在近海地区采集的大地电磁测深数据通常受到海岸效应的影响,使得大地电磁测深数据发生畸变,因而很难利用大地电磁测深资料较为可靠地获得地下深部的电性结构.本文通过正演模拟方法,分析和总结海水深度变化和海底地形变化对近海地区大地电磁测深数据的畸变影响.当测区与海岸线的距离小于目标频率的大地电磁场趋肤深度时,高导海洋的存在会严重影响测区内电磁场的分布.由于海岸效应的影响,大地电磁测深视电阻率曲线和相位曲线均会发生不同程度的畸变,在低频部分,这种畸变作用尤为明显.大地电磁测深一维Occam反演方法和二维非线性共轭梯度反演方法,对近海地区浅部地层具有较好的反演效果.随着海水深度的增加和海底地形的复杂变化,两种反演方法均会出现不同程度的假异常,为地质解释工作造成了影响.近渤海地区的实测大地电磁测深数据在低频部分可能受到海岸效应的影响而导致视电阻率曲线的严重畸变. 相似文献
2.
Mohamed Abdelzaher Jun Nishijima Hakim Saibi Gad El-Qady Usama Massoud Mamdouh Soliman Abdellatif Younis Sachio Ehara 《Pure and Applied Geophysics》2012,169(9):1679-1692
Magnetotelluric (MT) soundings and gravity methods were employed to study the deep freshwater aquifer in the area north of Abo Zenema city on the eastern side of the Gulf of Suez, Egypt. Seven MT sites and 48 gravity stations were surveyed along northeast–southwest profiles as close as possible to a line perpendicular to the coast of the Gulf of Suez. The MT survey was conducted using high and low frequencies to investigate shallow and deep areas, respectively. One-dimensional inversion was conducted using a heuristic inversion scheme of the Bostick algorithm. The MT data were also inverted with a 2-D smooth model inversion routine using the nonlinear conjugate gradient method to infer variation in vertical and lateral resistivity inside the Earth. A 100-Ohm-m homogeneous half-space initial model was used to invert the TE mode data only. Then, the inverted model obtained from the TE mode data was used as an initial model for inversion of the TM mode data. The inverted model thus obtained from the TM mode data inversion was used as an initial model for the inversion of the joint TE and TM responses. Two-dimensional (2-D) forward modeling of the gravity data was conducted using the 2-D polygon method of Talwani’s algorithm for an arbitrarily shaped body and was based on the subsurface information from the MT survey and the available information about the geological structure of the study area. This method enabled us to obtain the basement structure of the coastal aquifer in the study area. The results from the analysis and the interpretation of MT and gravity data were used to detect and delineate the groundwater coastal aquifer in the study area. 相似文献
3.
Yanling Shi Zhanxiang He Zuzhi Hu Qiang Wei Dechun Li Cuixian Meng Liansheng Ji Sheng Zhang 《Studia Geophysica et Geodaetica》2018,62(1):167-185
Mapping deep geological hydrocarbon targets is of significant importance in basin exploration. In areas lacking reliable seismic data, magnetotelluric (MT) and gravity explorations are helpful to delineate the distribution of potential deep geological hydrocarbon targets. Here we investigate the effectiveness of the integrated 3D MT and gravity explorations for mapping the potential deep hydrocarbon source rocks. The result based on the data from the W Basin (part of the Ordes Basin) of China demonstrates that the method is efficient and economical for basin exploration. The method is particularly useful in target areas which are of great interest for oil and gas exploration but lack high quality seismic data. In our method, we first use the high-precision 3D small-bin MT data acquisition to improve the data accuracy. Then we perform datum static correction method and apply 3D inversion to obtain the3D resistivity distribution. We also develop a layered resistivity model based on resistivity logging to assist the interpretation of the inverted 3D resistivity data so as to derive an initial 3D geological model. Starting from the initial model, we use 2D gravity data to update the model via 2D inversion line by line, and then pass the updated model for the next round of the 3D MT inversion. The integrated inversion is implemented iteratively so the model converges to satisfy the need of final geological analysis. The application to the W Basin shows that we could successfully delineate the geological distribution of the potential deep hydrocarbon source rocks within the basin and map the thickness of the upper Paleozoic. 相似文献
4.
稀疏测线大地电磁资料三维反演研究:合成算例(英文) 总被引：2，自引：1，他引：1
受勘探成本和工区环境等因素的影响,当前大多数大地电磁实际工作采取布置稀疏测线采集数据和使用二维反演方法解释这些稀疏测线数据的方式。然而,二维反演方法在解释三维地电构造数据时存在局限性,有时甚至做出错误的地质解释。本文尝试了使用三维反演方法对大地电磁稀疏测线数据进行反演解释。使用大地电磁全信息资料三维共轭梯度反演程序对理论模型合成稀疏测线数据进行了三维反演。结果表明:这种反演方案是可行与有效的。同时,我们发现在不同数据的三维反演结果中,四个张量阻抗元素和两个倾子数据同时反演的结果相对更为准确,更接近理论模型。 相似文献
5.
Magnetotelluric resistivity modeling for 3D characterization of geothermal reservoirs in the Western side of Mt. Aso, SW Japan 总被引：1，自引：1，他引：1
Hisafumi Asaue Katsuaki Koike Toru Yoshinaga Shinichi Takakura 《Journal of Applied Geophysics》2006,58(4):296
Geothermal reservoirs are usually located at a depth range of 2 to 5 km, so to efficiently utilize such resources an advanced prospecting method is needed to detect these deep geologic structures. This study aimed to three-dimensionally characterize geothermal reservoirs by a combination of Magnetotelluric (MT) survey, inversion analysis of apparent resistivity, and interpolation of the resistivity data obtained. The western side of Mt. Aso crater, southwest Japan, was chosen as the case study area. Three hot springs exist there and a fault is assumed to go in the direction connecting them. A MT survey was carried out at 26 sites and the data processed by a remote reference method to reduce artificial noises. Based on skewness and Mohr circle analyses of the impedance tensor, the local geologic structure at each site could be approximated as horizontally layered and therefore, a one-dimensional inversion analysis was applied to the MT raw data. The resultant resistivity column data were then interpolated by the three-dimensional optimization principle method. The resistivity distributions obtained clarified continuous conductors with especially low resistivity (less than 10 Ω·m) at the hot springs along the fault. Because the resistivity decreases largely with an abundance of clay minerals, the conductors could be considered to correspond with the cap rocks. Thus, two geothermal reservoirs, whose shapes were estimated to be pillar, were detected under the cap rocks in an elevation range of − 1000 to − 3000 m. By comparing the resistivity distributions with the temperature distributions based on fluid-flow calculations at a steady state using FEM, the validity of the location and dimension of the estimated reservoirs were confirmed. 相似文献
6.
在已有研究成果的基础上,为了适应物性参数剧烈变化的复杂模型并满足联合反演的要求,开发了速度和电阻率随机分布共网格单元模型的建模技术.基于这种统一的物性随机分布的网格介质模型,利用有限元方法和改进的射线追踪法分别正演计算大地电磁场和地震走时,结合改进的模拟退火算法,研究实现了电阻率和速度随机分布条件下的大地电磁与地震资料的同步联合反演.对物性界面不完全一致和物性变化剧烈的带地形复杂模型的试验,表明了该方法在精细反演复杂电阻率和速度结构方面的效果,克服了以往研究局限于简单模型的不足.对地震资料品质差的地区开展的实际资料联合反演,表明了方法的适用性,先验信息约束下的联合反演提高了反演精度. 相似文献
7.
大地电磁的反演问题是非线性,如果采用线性反演方法容易陷入局部极小,使得反演结果非唯一性严重.本文将人工鱼群算法引入到地球物理反演之中,提出了非线性的大地电磁人工鱼群最优化反演.该方法不需要进行偏导数的求取,可以对反演的范围进行约束,以减小反演结果的非唯一性.同时我们对搜索步长进行了改进,给出适用于大地电磁反演的人工鱼群参数.大量的理论数据试算表明,人工鱼群反演算法能够较好地寻找到全局最优解.实测数据的处理结果表明,该方法可以用来处理实际资料,并且能够取得很好的应用效果. 相似文献
8.
Airborne electromagnetic (AEM) surveys are currently being flown over populated areas and applied to detailed problems using high flight line densities. Interpretation information is supplied through a model of the subsurface resistivity distribution. Theoretical and survey data are used here to study the character and reliability of such models. Although the survey data were obtained using a fixed-wing system, the corresponding associations with helicopter, towed-bird systems are discussed. Both Fraser half-space and 1D inversion techniques are considered in relation to their ability to distinguish geological, cultural and environmental influences on the survey data. Fraser half-space modelling provides the dual interpretation parameters of apparent resistivity and apparent depth at each operational frequency. The apparent resistivity was found to be a remarkably stable parameter and appears robust to the presence of a variety of at-surface cultural features. Such features provide both incorrect altitude data and multidimensional influences. Their influences are observed most strongly in the joint estimate of apparent depth and this accounts for the stability of the apparent resistivity. Positive apparent depths, in the example data, result from underestimated altitude measurements. It is demonstrated that increasingly negative apparent depths are associated with increasing misfits between a 1D model and the data. Centroid depth calculations, which are a transform of the Fraser half-space parameters, provide an example of the detection of non-1D influences on data obtained above a populated area. 1D inversion of both theoretical and survey data is examined. The simplest use of the 1D inversion method is in providing an estimate of a half-space resistivity. This can be undertaken prior to multilayer inversion as an initial assessment. Underestimated altitude measurements also enter the problem and, in keeping with the Fraser pseudo-layer concept, an at-surface highly resistive layer of variable thickness can be usefully introduced as a constrained parameter. It is clearly difficult to ascribe levels of significance to a ‘measure’ of misfit contained in a negative apparent depth with the dimensions of metres. The reliability of 1D models is better assessed using a formal misfit parameter. With the misfit parameter in place, the example data suggest that the 1D inversion methods provide reliable apparent resistivity values with a higher resolution than the equivalent information from the Fraser half-space estimates. 相似文献
9.
交叉梯度联合反演方法通过对多种地球物理模型实现结构耦合,在岩石物性关系不确定的情况下,既能提高反演结果的可靠性,又能减少反演的多解性,还能减少不同方法解释结果之间的矛盾.当不同的模型观测数据覆盖范围不一致时,交叉梯度联合反演通常需要取出重叠区域数据进行联合反演,并且建模时还要扩展一些模型范围.本文首先提出并实现了部分区域约束下的交叉梯度多重地球物理数据联合反演算法;接着进行了算法的模型试算;最后,我们将该反演算法用于本溪—集安深部地质调查重磁电综合地质地球物理解释中.结果表明:该算法不但能在重叠区域内很好地恢复结构相似的模型,而且在非重叠区域与重叠区域的边界处仍然可以得到平滑变化的模型;在本溪—集安10号剖面所获得的结构上相似的电阻率、密度及磁化率模型较好地反映了该区的深部地质结构,对于确定深部地质体的性质提供了有力的证据. 相似文献
10.
Three-dimensional (3D) magnetotelluric (MT) surveys have been performed in Jeju, the largest volcanic island in Korea to figure out any possible structures or potential anomaly for remnant deep geothermal resources. Various approaches have been applied to interpret MT data observed in Jeju. MT dataset shows generally simple stratigraphy of four layers, though contains the severe static and the sea-effects. In our previous works, the induction vectors and 3D inversion results have commonly indicated the existence of a conductive anomaly in central parts of the island, beneath Mt. Halla. The 3D inversion dealt the static shifts as inversion parameters. The Jeju MT dataset, however, still contains the effect of conductive sea water surrounding the island.The sea-effect on MT impedance can be represented as a distortion tensor and excluded from the Jeju MT dataset by an iterative sea-effect correction. In this study, 3D inversion incorporating static shift parameterization was conducted using MT dataset corrected using 1D resistivity model obtained from the iterative scheme. Reasonably reconstructed images are obtained through the 3D inversion and using the MT dataset with sea-effect correction. The inversion result still shows the conductive anomaly in a similar depth. RMS misfits converged to a lower value than that of inversion using MT data before the sea-effect correction. From the fact, it is highly possible that the conductive anomaly is not an artifact but a real underground structure. Further investigation about the anomaly including exploration drilling is needed to see if it is from a fracture containing conductive sea water or related to the old volcanic activities. 相似文献
11.
Effects of the sea floor topography on the 1D inversion of time‐domain marine controlled source electromagnetic data 
下载免费PDF全文
下载免费PDF全文 Time‐domain marine controlled source electromagnetic methods have been used successfully for the detection of resistive targets such as hydrocarbons, gas hydrate, or marine groundwater aquifers. As the application of time‐domain marine controlled source electromagnetic methods increases, surveys in areas with a strong seabed topography are inevitable. In these cases, an important question is whether bathymetry information should be included in the interpretation of the measured electromagnetic field or not. Since multi‐dimensional inversion is still not common in time‐domain marine controlled source electromagnetic methods, bathymetry effects on the 1D inversion of single‐offset and multi‐offset joint inversions of time‐domain controlled source electromagnetic methods data are investigated. We firstly used an adaptive finite element algorithm to calculate the time‐domain controlled source electromagnetic methods responses of 2D resistivity models with seafloor topography. Then, 1D inversions are applied on the synthetic data derived from marine resistivity models, including the topography in order to study the possible topography effects on the 1D interpretation. To evaluate the effects of topography with various steepness, the slope angle of the seabed topography is varied in the synthetic modelling studies for deep water (air interaction is absent or very weak) and shallow water (air interaction is dominant), respectively. Several different patterns of measuring configurations are considered, such as the systems adopting nodal receivers and the bottom‐towed system. According to the modelling results for deep water when air interaction is absent, the 2D topography can distort the measured electric field. The distortion of the data increases gradually with the enlarging of the topography's slope angle. In our test, depending on the configuration, the seabed topography does not affect the 1D interpretation significantly if the slope angle is less or around 10°. However, if the slope angle increases to 30° or more, it is possible that significant artificial layers occur in inversion results and lead to a wrong interpretation. In a shallow water environment with seabed topography, where the air interaction dominates, it is possible to uncover the true subsurface resistivity structure if the water depth for the 1D inversion is properly chosen. In our synthetic modelling, this scheme can always present a satisfactory data fit in the 1D inversion if only one offset is used in the inversion process. However, the determination of the optimal water depth for a multi‐offset joint inversion is challenging due to the various air interaction for different offsets. 相似文献
12.
13.
Behrooz Oskooi Mahmoud Mirzaei Behnam Mohammadi Mohammad Mohammadzadeh-Moghaddam Feridon Ghadimi 《Studia Geophysica et Geodaetica》2016,60(1):141-161
Magnetotelluric (MT) and ground magnetic surveys were conducted on the Mahallat geothermal field situated in Markazi province, central Iran, as a primary part of the explorations and developments of a geothermal energy investigation program in the region. Mahallat region has the greatest geothermal fields in Iran. MT survey was performed in November 2011 on an 8 km profile crossing the hot springs with a total of 17 stations. The 2D inversion of the determinant MT data was performed using a 2D inversion routine based on the Occam approach. The 2D resistivity model obtained from the determinant data shows a low resistivity zone at 800-2000 m depth and a higher resistivity zone above the low resistivity zone, interpreted as geothermal reservoir and cap rock, respectively. It also revealed two major concealed faults which are acting as preferential paths for the circulation of hydrothermal fluids. To obtain more geophysical evidence, a ground magnetic survey with 5000 stations was also performed over an area of 200 km2 around the MT profile. Magnetic measurements show a main positive anomaly of about +1000 nT over the study area, which could be interpreted as an intrusive body with the high magnetic susceptibility (i.e. mafic and ultramafic rocks) into the sedimentary host rocks. We interpret the body as the heat source of the geothermal system. Structural index and depth estimation of the anomaly indicate that the intrusive body is similar to a cylinder extending from about one kilometer depth down to greater depths. The results of MT and magnetic investigations indicate a geothermal reservoir which proves the preliminary geological observations to a great extent. 相似文献
14.
Exploration of geothermal structure in Puga geothermal field, Ladakh Himalayas, India by magnetotelluric studies 总被引：2，自引：1，他引：2
T. Harinarayana K.K. Abdul Azeez D.N. Murthy K. Veeraswamy S.P. Eknath Rao C. Manoj K. Naganjaneyulu 《Journal of Applied Geophysics》2006,58(4):280
To understand the crustal electric structure of the Puga geothermal field located in the Ladakh Himalayas, wide band (1000 Hz–0.001 Hz) magnetotelluric (MT) study have been carried out in the Puga area. Thirty-five MT sites were occupied with site spacing varying from 0.4 to 1 km. The measurements were carried out along three profiles oriented in east–west direction. After the preliminary analysis, the MT data were subjected to decomposition techniques. The one-dimensional inversion of the effective impedance data and the two-dimensional inversion of the TE (transverse electric) and TM (transverse magnetic) data confirm the presence of low resistive (5–25 Ω m) near surface region of 200–300 m thick in the anomalous geothermal part of the area related to the shallow geothermal reservoir. Additionally, the present study delineated an anomalous conductive zone (resistivity less than 10 Ω m) at a depth of about 2 km which is possibly related to the geothermal source in the area. A highly resistive basement layer separates the surface low resistive region and anomalous conductive part. The estimated minimum temperature at the top of conductive part is about 250 °C. The significance of the deeper conductive zone and its relation to the geothermal anomaly in the area is discussed. 相似文献
15.
地表起伏地形在野外矿产资源勘察中不可避免,其对直流电阻率法勘探影响巨大.近年来,电阻率三维正演取得诸多进展,特别是应用非结构网格我们能够进行任意复杂地形和几何模型的电阻率三维数值模拟,但面向实际应用的起伏地形下电阻率三维反演依然困难.本文基于非结构化四面体网格,并考虑到应用GPS/GNSS时,区域地球物理调查中可非规则布设测网的实际特点,实现了任意地形(平坦或起伏)条件下、任意布设的偶极-偶极视电阻率数据的不完全Gauss-Newton三维反演.合成数据的反演结果表明了方法的有效性,可应用于复杂野外环境下的三维电法勘探. 相似文献
16.
本文从大地电磁扬的色散关系出发,阐述了进行大地电磁资料一维联合反演的物理意义。论证了对于以色散关系相联系的一对大地电磁响应函数,特别是阻抗实部和虚部视电阻率进行联合反演的必要性和可能的应用前景。对比研究了大地电磁阻抗各单参量及其联合反演的效果。结果表明,在加快反演迭代速度,限定反演解的非唯一性、保证反演迭代的稳定进行等方面,联合反演比单参量反演具有明显的优越性;在大多数情况下,阻抗实部视电阻率和阻抗虚部视电阻率联合反演的效果要比通常所采用的常规视电阻率和阻抗相位的联合反演效果好。实际大地电磁资料的试验表明,各种不同平均阻抗的利用和综合反演解释将有助于获得更为可靠的结果。 相似文献
17.
Trans‐dimensional Bayesian inversion of controlled‐source electromagnetic data in the German North Sea 下载免费PDF全文
下载免费PDF全文 Romina A. S. Gehrmann Jan Dettmer Katrin Schwalenberg Martin Engels Stan E. Dosso Asli Özmaral 《Geophysical Prospecting》2015,63(6):1314-1333
This paper presents the first controlled‐source electromagnetic survey carried out in the German North Sea with a recently developed seafloor‐towed electrical dipole–dipole system, i.e., HYDRA II. Controlled‐source electromagnetic data are measured, processed, and inverted in the time domain to estimate an electrical resistivity model of the sub‐seafloor. The controlled‐source electromagnetic survey targeted a shallow, phase‐reversed, seismic reflector, which potentially indicates free gas. To compare the resistivity model to reflection seismic data and draw a combined interpretation, we apply a trans‐dimensional Bayesian inversion that estimates model parameters and uncertainties, and samples probabilistically over the number of layers of the resistivity model. The controlled‐source electromagnetic data errors show time‐varying correlations, and we therefore apply a non‐Toeplitz data covariance matrix in the inversion that is estimated from residual analysis. The geological interpretation drawn from controlled‐source electromagnetic inversion results and borehole and reflection seismic data yield resistivities of ～1 Ωm at the seafloor, which are typical for fine‐grained marine deposits, whereas resistivities below ～20 mbsf increase to 2–4 Ωm and can be related to a transition from fine‐grained (Holocene age) to unsorted, coarse‐grained, and compacted glacial sediments (Pleistocene age). Interface depths from controlled‐source electromagnetic inversion generally match the seismic reflector related to the contrast between the different depositional environments. Resistivities decrease again at greater depths to ～1 Ωm with a minimum resistivity at ～300 mbsf where a seismic reflector (that marks a major flooding surface of late Miocene age) correlates with an increased gamma‐ray count, indicating an increased amount of fine‐grained sediments. We suggest that the grain size may have a major impact on the electrical resistivity of the sediment with lower resistivities for fine‐grained sediments. Concerning the phase‐reversed seismic reflector that was targeted by the survey, controlled‐source electromagnetic inversion results yield no indication for free gas below it as resistivities are generally elevated above the reflector. We suggest that the elevated resistivities are caused by an overall decrease in porosity in the glacial sediments and that the seismic reflector could be caused by an impedance contrast at a thin low‐velocity layer. Controlled‐source electromagnetic interface depths near the reflector are quite uncertain and variable. We conclude that the seismic interface cannot be resolved with the controlled‐source electromagnetic data, but the thickness of the corresponding resistive layer follows the trend of the reflector that is inclined towards the west. 相似文献
18.
O. L. Poltaratskaya E. B. Fainberg B. Sh. Singer 《Izvestiya Physics of the Solid Earth》2006,42(1):51-59
Analysis of magnetotelluric (MT) sounding studies in western Yakutia showed that amplitude curves are strongly affected by the regional distribution of electrical conductivity heterogeneities of the sedimentary cover, while phase curves are distorted to a lesser extent. The distribution of the longitudinal conductance in the sedimentary cover is constructed, and MT fields and resistivity and phase curves are modeled. Based on combined analysis of experimental and model data and results of inversion of corrected curves, an interpretation of main anomalies of MT fields is given and a regional crustal anomaly of the electrical conductivity is discovered. 相似文献
19.
复杂地形、地质条件的大地电磁数据解释容易出现假象,采用三维正演技术模拟地形和地表不均匀体的背景响应,对实测数据阻抗相位不变量进行校正,实现更准确的定性分析;对三维异常体模型的合成数据进行一维、二维多参数反演试算,以确定地形剧变区选择反演技术的最佳方案.合成数据的试反演结果显示一维反演水平切片假异常较多,二维反演能压制测向假异常,但不能压制走向的假异常,水平切片多出现测向条带.使用本文提出的阻抗相位不变量校正法扣除地形、地表背景响应,结合一维、二维反演,能使实际资料解释成果更加可靠. 相似文献