共查询到20条相似文献，搜索用时 149 毫秒
1.
The last two decades have witnessed the development and application of well-balanced numerical models for shallow flows in natural rivers.However,until now there have been no such models for flows with non-uniform sediment transport.This paper presents a 1D well-balanced model to simulate flows and non-capacity transport of non-uniform sediment in alluvial rivers.The active layer formulation is adopted to resolve the change of bed sediment composition.In the framework of the finite volume Slope Llmiter Centred(SLIC) scheme,a surface gradient method is incorporated to attain well-balanced solutions to the governing equations.The proposed model is tested against typical cases with irregular topography,including the refilling of dredged trenches,aggradation due to sediment overloading and flood flow due to landslide dam failure.The agreement between the computed results and measured data is encouraging.Compared to a non-well-balanced model,the well-balanced model features improved performance in reproducing stage,velocity and bed deformation.It should find general applications for non-uniform sediment transport modelling in alluvial rivers,especially in mountain areas where the bed topography is mostly irregular. 相似文献
2.
Channel curvature produces secondary currents and a transverse sloping channel bed, along which the depth increases towards the outer bank. As a result deep pools tend to form adjacent to the outer bank, promoting bank collapse. The interaction of sediment grains with the primary and secondary flow and the transverse sloping bed also causes meanders to move different grain sizes in different proportions and directions, resulting in a consistent sorting pattern. Several models have been developed to describe this process, but they all have the potential to over‐predict pool depth because they cannot account for the influence of erodible banks. In reality, bank collapse might lead to the development of a wider, shallower cross‐section and any resulting flow depth discrepancy can bias associated predictions of flow, sediment transport, and grain‐size sorting. While bed topography, sediment transport and grain sorting in bends will partly be controlled by the sedimentary characteristics of the bank materials, the magnitude of this effect has not previously been explored. This paper reports the development of a model of flow, sediment transport, grain‐size sorting, and bed topography for river bends with erodible banks. The model is tested via intercomparison of predicted and observed bed topography in one low‐energy (5·3 W m?2 specific stream power) and one high‐energy (43·4 W m?2) study reach, namely the River South Esk in Scotland and Goodwin Creek in Mississippi, respectively. Model predictions of bed topography are found to be satisfactory, at least close to the apices of bends. Finally, the model is used in sensitivity analyses that provide insight into the influence of bank erodibility on equilibrium meander morphology and associated patterns of grain‐size sorting. The sensitivity of meander response to bank cohesion is found to increase as a function of the available stream power within the two study bends. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
3.
Effect of cross‐section interpolated bathymetry on 2D hydrodynamic model results in a large river 
下载免费PDF全文
下载免费PDF全文 Two‐dimensional (2D) hydrodynamic models have been increasingly used to quantify aquatic habitat and stream processes, such as sediment transport, streambed morphological evolution, and inundation extents. Because river topography has a strong influence on predicted hydraulic conditions, 2D models require accurate and detailed bathymetric data of the stream channel and surrounding floodplains. Besides collection of mass points to construct high‐resolution three‐dimensional surfaces, bathymetries may be interpolated from cross‐sections. However, limited information is available on the effects of cross‐section spacing and the derived interpolated bathymetry on 2D model results in large river systems. Here, we investigated the effects of cross‐section spacing on flow properties simulated with 2D modeling at low, medium and high discharges in two morphologically different reaches, a simple (almost featureless with low sinuosity) and a complex (presenting pools, riffles, runs, contractions and expansions) reach of the Snake River (Idaho, USA), the tenth largest river in the United States in terms of drainage area. We compared the results from 2D models developed with complete channel bathymetry acquired with multibeam sonar data and photogrammetry, with 2D model results that were developed using interpolated topography from uniformly distributed transects. Results indicate that cross‐sections spaced equal to or greater than 2 times the average channel width (W*) smooths the bathymetry and suppresses flow structures. Conversely, models generated with cross‐sections spaced at 0.5 and 1 W* have stream flow properties, sediment mobility and spatial habitat distribution similar to those of the complete bathymetry. Furthermore, differences in flow properties between interpolated and complete topography models generally increase with discharge and with channel complexity. Copyright © 2013 John Wiley & Sons, Ltd. 相似文献
4.
《Advances in water resources》2007,30(4):715-729
Flow, sediment transport and bed deformation in alluvial rivers normally exhibit multiple time scales. Enhanced knowledge of the time scales can facilitate better approaches to the understanding of the fluvial processes. Yet prior studies of the time scales are based upon the concept of sediment transport capacity at low concentrations, which however is not generally applicable. This paper presents new formulations of the time scales of fluvial flow, suspended sediment transport and bed deformation, under the framework of shallow water hydrodynamics, non-capacity sediment transport and the theory of characteristics for the hyperbolic governing equations. The time scale of bed deformation in relation to that of flow depth is demonstrated to delimit the applicability region of mathematical river models, and the time scale of suspended sediment transport relative to that of the pertinent flow information is analyzed to address if the concept of sediment transport capacity is applicable. For shallow flows with high sediment concentrations, bed deformation may considerably affect the flow and a fully coupled model is normally required. In contrast, for deep flows at low sediment concentrations, a decoupled model is mostly justified. This pilot study of the time scales delivers a new theoretical basis, on which the interaction between flow, suspended sediment transport and bed deformation can be potentially better characterized. 相似文献
5.
海岸带地区是全球自然生态环境最为复杂和脆弱的地域之一,合成孔径雷达干涉测量（InSAR）技术可以为全球人类活动、气候变暖和俯冲带剧烈构造运动等背景下的大范围海岸带地理环境变化研究提供重要观测资料.海洋潮汐导致固体地球长周期形变,波长尺度为102~103 km的海潮负荷引入mm级至cm级的形变梯度,此类非构造信号对海岸带InSAR精密形变分析（如：大范围、微小、缓慢且非稳态构造过程等）造成显著影响.本文以宽幅模式SAR数据为例,基于多种海潮模型研究了全球典型海岸带地区（福建、智利和阿拉斯加湾）海潮负荷效应对宽幅InSAR形变监测的影响,给出了宽幅InSAR海潮负荷三维分量估计与差分相位提取方法,并进一步讨论了基于不同海潮模型估计海潮负荷位移的差异.海潮负荷影响不仅与研究范围大小有关,其形变梯度变化与研究区域地形特征存在强相关,对于长波长形变分析而言,传统平面或者曲面拟合方法难以有效分离海潮负荷位移. 相似文献
6.
7.
《国际泥沙研究》2016,(2):139-148
Applications of sediment transport and water flow characteristics based sediment transport simulation models for a river system are presented in this study. An existing water–sediment model and a new sediment–water model are used to formulate the simulation models representing water and sediment movement in a river system. The sediment–water model parameters account for water flow characteristics embodying sediment transport properties of a section. The models are revised formulations of the multiple water inflows model describing water movement through a river system as given by the Muskingum principle. The models are applied to a river system in Mississippi River basin to estimate downstream sediment concentration, sediment discharge, and water discharge. River system and the river section parameters are estimated using a revised and the original multiple water inflows models by applying the genetic algorithm. The models estimate downstream sediment transport rates on the basis of upstream sediment/water flow rates to a system. Model performance is evaluated by using standard statistical criteria;downstream water discharge resulting from the original multiple water inflows model using the estimated river system parameters indicate that the revised models satisfactorily describe water movement through a river system. Results obtained in the study demonstrate the applicability of the sediment transport and water flow characteristics-based simulation models in predicting downstream sediment transport and water flow rates in a river system. 相似文献
8.
The climax of the Kos Plateau Tuff (KPT) eruption (eastern Aegean, Greece) generated a highly energetic, coarse-grained, lithic-rich, pyroclastic flow. In most places on Kos, the deposit from this event is an ignimbrite (ignimbrite El) that comprises a basal, coarse-grained, lithic breccia and overlying pumiceous part, above a planar, strongly erosional lower contact. However, along the northern coast of central Kos, "normal" ignimbrite El overlies a hummocky, 6-m-thick layer of chaotic breccia comprising mingled-to-pervasively mixed ignimbrite El and unconsolidated sediment. The surface morphology of the chaotic breccia and its internal texture resemble those of a debris-avalanche deposit, but the breccia is neither proximal nor downcurrent of steep topography. The lower part of the chaotic breccia comprises distinct domains of unconsolidated sediment or lower KPT units that are deformed and/or mingled with pumiceous ignimbrite. The upper part is dominated by a matrix of mingled-to-pervasively mixed ignimbrite and sediment that contains sediment domains as large as 2-10 m in diameter. Such large intact allochthonous domains are best preserved at the top of the chaotic breccia and form the hummocks. The chaotic breccia formed synchronously with the passage of a highly energetic pyroclastic flow where it traversed wet, unconsolidated sediment. Shear-induced liquification, together with possible ground shaking associated with the eruption, probably caused failure. Part of the unconsolidated substrate and basal part of ignimbrite El were dislodged and resedimented a short distance (tens to hundreds of metres) downcurrent. The lower part records deformation and disintegration of the substrate induced by the overriding, shearing flow. Mingling and deformation of the poorly consolidated material occurred as a result of within-flow lateral shear. Attenuated worm burrows within the sediment domains, and pinch-and-swell and flame structures within the mingled domains, preserve evidence of shear in the lower part. The upper part was transported downcurrent above a zone of shear failure. Internal heterogeneities in physical properties resulted in variable strain rates causing some domains to be pervasively mixed while others remained intact. Intact large unconsolidated domains at the top were transported mostly above the zone of shearing. 相似文献
9.
R. P. C. Morgan J. N. Quinton R. E. Smith G. Govers J. W. A. Poesen K. Auerswald G. Chisci D. Torri M. E. Styczen 《地球表面变化过程与地形》1998,23(6):527-544
The European Soil Erosion Model (EUROSEM) is a dynamic distributed model, able to simulate sediment transport, erosion and deposition over the land surface by rill and interill processes in single storms for both individual fields and small catchments. Model output includes total runoff, total soil loss, the storm hydrograph and storm sediment graph. Compared with other erosion models, EUROSEM has explicit simulation of interill and rill flow; plant cover effects on interception and rainfall energy; rock fragment (stoniness) effects on infiltration, flow velocity and splash erosion; and changes in the shape and size of rill channels as a result of erosion and deposition. The transport capacity of runoff is modelled using relationships based on over 500 experimental observations of shallow surface flows. EUROSEM can be applied to smooth slope planes without rills, rilled surfaces and surfaces with furrows. Examples are given of model output and of the unique capabilities of dynamic erosion modelling in general. © 1998 John Wiley & Sons, Ltd. 相似文献
10.
Physically based models are useful frameworks for testing intervention strategies designed to reduce elevated sediment loads in agricultural catchments. Evaluating the success of these strategies depends on model accuracy, generally established by a calibration and evaluation process. In this contribution, the physically based SHETRAN model was assessed in two similar U.K. agricultural catchments. The model was calibrated on the Blackwater catchment (18 km2) and evaluated in the adjacent Kit Brook catchment (22 km2) using 4 years of 15 min discharge and suspended sediment flux data. Model sensitivity to changes in single and multiple combinations of parameters and sensitivity to changes in digital elevation model resolution were assessed. Model flow performance was reasonably accurate with a Nash–Sutcliffe efficiency coefficient of 0.78 in Blackwater and 0.60 in Kit Brook. In terms of event prediction, the mean of the absolute percentage of difference (μAbsdiff) between measured and simulated flow volume (Qv), peak discharge (Qp), sediment yield (Sy), and peak sediment flux (Sp) showed larger values in Kit Brook (48% [Qv], 66% [Qp], 298% [Sy], and 438% [Sp]) compared with the Blackwater catchment (30% [Qv], 41% [Qp], 106% [Sy], and 86% [Sp]). Results indicate that SHETRAN can produce reasonable flow prediction but performs less well in estimation of sediment flux, despite reasonably similar hydrosedimentary behaviour between catchments. The sensitivity index showed flow volume sensitive to saturated hydraulic conductivity and peak discharge to the Strickler coefficient; sediment yield was sensitive to the overland flow erodibility coefficient and peak sediment flux to raindrop/leaf soil erodibility coefficient. The multiparameter sensitivity analysis showed that different combinations of parameters produced similar model responses. Model sensitivity to grid resolution presented similar flow volumes for different digital elevation model resolutions, whereas event peak and duration (for both flow and sediment flux) were highly sensitive to changes in grid size. 相似文献
11.
The geomorphology of the southern Yellow Sea（SYS） is characterized by offshore radial sand ridges（RSR）.An offshore tidal channel（KSY Channel） is located perpendicular to the coast,comprised of a main and a tributary channel separated by a submarine sand ridge（KSY Sand Ridge） extending seaward.In order to investigate the interactions among water flow,sediment transport,and topography,current velocity and suspended sediment concentration（SSC） were observed at 11 anchor stations along KSY Channel in RSR during a spring tide cycle.High resolution bottom topography was also surveyed.Residual currents and tidally averaged suspended sediment fluxes were calculated and analyzed by using the decomposition method.Results suggested that the water currents became stronger landward but with asymmetrical current speed and temporal duration of flood and ebb tides.Residual currents showed landward water transport in the nearshore channel and a clockwise circulation around the KSY Sand Ridge.Tidally-averaged SSC also increased landward along the channel.The main mechanisms controlling SSC variations were resuspension and horizontal advection,with spatial and temporal variations in the channel,which also contributed to sediment redistribution between channels and sand ridges.Residual flow transport and the tidal pumping effect dominated the suspended sediment flux in the KSY Channel.The KSY Sand Ridge had a potential southward migration due to the interaction between water flow,sediment transport,and topography. 相似文献
12.
A three-dimensional k-ε-Ap two-fluid turbulence model is proposed to study liquid-particle two-phase flow and bed deformation.By solving coupled liquid-phase and solid-phase governing equations in a finite-volume method,the model can calculate the movement of both water and sediment.The model was validated by water-sediment transport in a 180° channel bend with a movable bed.The validation concerns two-phase time-averaged velocities,bed deformation,water depth,depth-averaged streamwise velocity,cross-stream bed profiles,and two-phase secondary flow velocity vectors.The agreement between numerical results and experimental results was generally good.The comparisons of the numerical results of different models show that the three-dimensional k-ε-Ap two-fluid turbulence model has a relatively higher accuracy than one-fluid model. 相似文献
13.
14.
Turbidity currents may feature active sediment transport and rapid bed deformation, such as those responsible for the erosion of many submarine canyons. Yet previous mathematical models are built upon simplified governing equations and involve steady flow and weak sediment transport assumptions, which are not in complete accordance with rigorous conservation laws. It so far remains unknown if these could have considerable impacts on the evolution of turbidity currents. Here a fully coupled modeling study is presented to gain new insights into the evolution of turbidity currents. The recent analysis of the multiple time scales of subaerial sediment-laden flows over erodible bed [Cao Z, Li Y, Yue Z. Multiple time scales of alluvial rivers carrying suspended sediment and their implications for mathematical modeling. Adv Water Resour 2007;30(4):715–29] is extended to subaqueous turbidity currents to complement the fully coupled modeling. Results from numerical simulations show the ability of the present coupled model to reproduce self-accelerating turbidity currents. Comparison among the fully and partially coupled and decoupled models along with the analysis of the relative time scale of bed deformation explicitly demonstrate that fully coupled modeling is essential for refined resolution of those turbidity currents featuring active sediment transport and rapid bed deformation, and existing models based on simplified conservation laws need to be reformulated. 相似文献
15.
This paper outlines a numerical model for the prediction of floodplain inundation sequences, overbank deposition rates and deposit grain size distributions. The model has two main components: first, a simplified hydraulic scheme which predicts floodwater flow depths and velocities, and second, a sediment transport element which employs a mass balance relation describing suspended sediment dispersion by convective and diffusive processes and sediment deposition as a function of particle settling rates. These relationships are solved numerically on a finite difference grid that accurately replicates the complex topographic features typical of natural river floodplains. The model is applied to a 600 m reach of the River Culm, Devon, U.K. using data derived from a range of field and laboratory techniques. Continuous records of river stage and suspended sediment concentration provide the model's upstream boundary input requirements. These are supplemented by measurements of the in situ settling characteristics of the suspended sediment load. The model's sediment transport component is calibrated with the aid of a dataset of measured overbank deposition amounts derived from flood events over a 16 month period. The model is shown to predict complicated floodwater inundation sequences and patterns of suspended sediment dispersion and deposition, which are largely a product of the complex topography of the floodplain. These results compare favourably with observations of overbank processes and are an improvement over those of previous models which have employed relatively simple representations of floodplain geometry. © 1997 by John Wiley & Sons, Ltd. 相似文献
16.
A Lagrangian marker particle in Eulerian finite difference cell solution to the three-dimensional incompressible mass transport equation was developed for predicting particulate transport in coastal and estuarine waters. Special features of the solution procedure include a finite difference grid network which translates horizontally and vertically with the mean particle motion and expands with the dispersive growth of the marker particle cloud. The cartesian vertical coordinate of the three-dimensional mass transport equation has been transformed, using instantaneous water column depth to allow adaptation to flow situations with a temporally and spatially varying bottom topography and free surface. Results from this model for turbulent diffusion and advection of a uniform plug flow of sediment in an unbounded uniform flow field with various sediment settling velocities were in excellent agreement with the corresponding analytic solutions. Using current information from a two-dimensional vertically averaged hydrodynamic's model, the model was utilized to predict the long term diffusion and advection of dilute neutrally and negatively buoyant suspended sediment clouds resulting from a hypothetical instantaneous release of dredge spoil waste at Brown's Ledge in Rhode Island Sound. 相似文献
17.
F. Donnadieu K. Kelfoun B. van Wyk de Vries E. Cecchi O. Merle 《Journal of Volcanology and Geothermal Research》2003,123(1-2):161
Three techniques of digital photogrammetry have been applied successfully to laboratory analogue models to study surface displacements caused by various volcano deformation types. Firstly, side-perspective videos are used to differentiate profile displacements between cryptodome intrusion models and models deforming by ductile inner-core viscous flow. Both models show similar morphologic features including a bulged flank and an asymmetric upper graben. However, differences in displacement trajectories of the bulge crest reflect upward intrusion push contrasting with essentially downward displacement vectors of weak core models. The other two techniques use vertical views correlated automatically either as time-sequence monoscopic views or as coeval stereoscopic pairs. This exploits to a maximum the method’s potential by imaging surface displacements over the whole model. Successive monoscopic photograms, because they suffer only moderate numerical processing for topographic effect removal, can detect very small displacements occurring early in deformation processes. As illustrated by analysis of intrusion models, the monoscopic method allows prediction of fault locations and main displacement locations. It can also anticipate the principal strain directions, and separate different deformation stages. On the other hand, the stereo-photogrammetry technique, although more complicated, provides topography and volume changes, as well as pictures of surface displacements in three dimensions. Results are presented for the spreading of volcano models on a ductile substratum and viscous cored cones. We have found digital photogrammetry to be a useful tool for analogue modelling, because it provides quantitative data on surface displacements, including movement invisible to the eye, as well as topographic changes. It is a good method for investigating and comparing different deformation mechanisms. It is especially useful for interpretation of displacement patterns obtained from monitoring of natural active volcanoes. In fact, results of the methods used in the laboratory can be directly compared with field data from geodetic or photogrammetric surveys, as at Mount St. Helens in 1980. 相似文献
18.
This paper discusses a model which simulates dune development resulting from aeolian saltation transport. The model was developed for application to coastal foredunes, but is also applicable to sandy deserts with transverse dunes. Sediment transport is calculated using published deterministic and empirical relationships, describing the influence of meteorological conditions, topography, sediment characteristics and vegetation. A so-called adaptation length is incorporated to calculate the development of transport equilibrium along the profile. Changes in topography are derived from the predicted transport, using the continuity equation. Vegetation height is incorporated in the model as a dynamic variable. Vegetation can be buried during transport events, which results in important changes in the sediment transport rates. The sediment transport model is dynamically linked to a second-order closure air flow model, which predicts friction velocities over the profile, influenced by topography and surface roughness. Modelling results are shown for (a) the growth and migration of bare, initially sine-shaped dunes, and (b) dune building on a partly vegetated and initially flat surface. Results show that the bare symmetrical dunes change into asymmetric shapes with a slipface on the lee side. This result could only be achieved in combination with the secondorder closure model for the calculation of air flow. The simulations with the partly vegetated surfaces reveal that the resulting dune morphology strongly depends on the value of the adaptation length parameter and on the vegetation height. The latter result implies that the dynamical interaction between aeolian activity and vegetation (reaction to burial, growth rates) is highly relevant in dune geomorphology and deserves much attention in future studies. Copyright © 1999 John Wiley & Sons, Ltd. 相似文献
19.
HUANG Jinchi Senter Engineer Institute of Water Resources Hydropower Research Fuxing Road No. Beijing China WAN Zhaohui Professor Institute of Water Resources Hydropower Research Chegongzhuang West Road No. Beijing P.O.Box 《国际泥沙研究》1997,(3)
I.INTRODUCTIONTwo-dimensionalnumericalmodelisaPOwerfoltoolforengineersandriVermanagerstopredictfloodhydxaulics,identifyareasofinundation,anddesignoptionsforfloodcontrollingstructures.SomespecialproblemswithheavilysedimentladenflowriVershouldbecarefullyconsideredforthenumericalmodeldesigning;1.theplaneformofariVerisusuallybraidedanditsmainchannelshiftsoften.Themainchannelandbarreplaceeachotherseveraltimesinonefloodevent.Atagivenlocationthewaterdepthmaychangefromover10meterstoseveralcenhm… 相似文献
20.
Post-fire debris flows represent one of the most erosive consequences associated with increasing wildfire severity and investigations into their downstream impacts have been limited. Recent advances have linked existing hydrogeomorphic models to predict potential impacts of post-fire erosion at watershed scales on downstream water resources. Here we address two key limitations in current models: (1) accurate predictions of post-fire debris flow volumes in the absence of triggering storm rainfall intensities and (2) understanding controls on grain sizes produced by post-fire debris flows. We compiled and analysed a novel dataset of depositional volumes and grain size distributions (GSDs) for 59 post-fire debris flows across the Intermountain West (IMW) collected via fieldwork and from the literature. We first evaluated the utility of existing models for post-fire debris flow volume prediction, which were largely developed for Southern California. We then constructed a new post-fire debris flow volume prediction model for the IMW using a combination of Random Forest modelling and regression analysis. We found topography and burn severity to be important variables, and that the percentage of pre-fire soil organic matter was an essential predictor variable. Our model was also capable of predicting debris flow volumes without data for the triggering storm, suggesting that rainfall may be more important as a presence/absence predictor, rather than a scaling variable. We also constructed the first models that predict the median, 16th percentile, and 84th percentile grain sizes, as well as boulder size, produced by post-fire debris flows. These models demonstrate consistent landscape controls on debris flow GSDs that are related to land cover, physical and chemical weathering, and hillslope sediment transport processes. This work advances our ability to predict how post-fire sediment pulses are transported through watersheds. Our models allow for improved pre- and post-fire risk assessments across diverse ranges of watersheds in the IMW. 相似文献