共查询到18条相似文献，搜索用时 437 毫秒
1.
为研究液化场地变截面桩的动力响应,依托翔安大桥实体工程,采用有限元软件,建立变截面桩－土和等截面桩－土相互作用模型,模拟液化场地变截面桩及等截面桩在地震作用下的振动反应,分析在地震作用下变截面位置不同的变截面桩及等截面桩的动力响应特征。结果表明:地震作用下,液化土层不同深度处的孔压比变化规律基本相同,均从0逐渐增大最后趋于稳定;变截面桩的桩身加速度和桩身位移均大于等截面桩,且桩顶加速度峰值出现的时刻均滞后于桩底;在饱和砂土层处,桩身位移变化趋势均较陡;变截面桩的桩身弯矩峰值和桩身剪力峰值均大于等截面桩,且其峰值出现的位置较等截面桩深;地震作用下,变截面桩及等截面桩的弯矩与剪力均在安全范围之内;液化场地变截面梁桥桩基础抗震设计时,应着重分析液化土层与非液化土层分界面以下的抗弯能力设计及液化土层中抗剪能力设计。 相似文献
2.
基于u-p有限元公式模拟饱和砂土中水和土颗粒完全耦合效应,建立液化侧向流场地群桩动力反应分析的三维数值模型。模型中,砂土采用多屈服面弹塑性本构模型模拟、黏土采用多屈服面运动塑性模型模拟,群桩在计算过程中保持线弹性状态;采用20节点的六面体单元和考虑孔压效应的20-8节点分别划分黏土层和饱和砂层;选用剪切梁边界处理计算域的人工边界,模拟地震过程中土层的剪切效应;应用瑞利阻尼考虑体系的阻尼效应。随后对比分析2×2群桩中各单桩的地震反应规律,结果表明,各单桩的弯矩、位移时程规律基本一致,峰值弯矩及峰值位移出现时刻滞后于输入加速度峰值时刻,上坡向桩的弯矩和位移峰值大于下坡向的桩的反应值。接着通过改变桩间距研究群桩效应,随着桩间距增加,群桩中各单桩的弯矩最大值均出现在土层分界处,且各单桩的弯矩、桩顶位移逐渐增大。最后给出液化侧向流场地群桩效应的基本原因,得出该类场地群桩抗震设计的基本认识。 相似文献
3.
《地震工程与工程振动》2021,41(3)
为研究动荷载作用下饱和砂土发生液化前后斜群桩的动力响应相关问题,利用土工离心机振动台进行了饱和砂土场地条件下的斜群桩物理模型试验。通过试验分别对土层响应、桩身弯矩以及桩顶承台加速度和位移等进行了详细分析,得到了如下结论:不同荷载作用下土层液化范围的改变导致了土层加速度峰值出现了不同程度的放大或缩小现象;砂土液化前后桩身动弯矩和残余弯矩对整个桩身的影响程度发生了显著变化,尤其在砂土大范围液化后残余弯矩相比动弯矩的影响明显减弱;当输入加速度峰值较小时,桩顶承台水平加速度峰值与振动台台面比较出现了明显的放大现象。而随着输入加速度峰值的增加,在振动后期承台水平加速度峰值出现了缩小的现象,同时在振动结束后承台产生了明显的动态残余位移。本研究取得的相关结论为液化土中斜群桩的相关研究以及工程设计提供参考。 相似文献
4.
《地震工程与工程振动》2021,41(5)
基于OpenSees计算软件建立液化微倾场地群桩-土动力相互作用有限元模型,分析液化微倾场地饱和砂土p-y曲线特性,系统研究了场地倾斜角度、桩径、地震作用幅值和基桩位置对饱和砂土动力p-y曲线特性影响。研究表明:土体即将液化时,桩基土反力达到峰值;土体液化后,土体表现出了流体特性;土反力峰值、桩土相对位移峰值和初始刚度随场地倾斜角度增加而增大;桩径越大,液化砂土的耗能效应越明显;随着地震作用幅值的增加,桩土相对位移峰值和土反力峰值也随之增加;液化微倾场地上坡桩受到的土体侧向流动力大于下坡桩。 相似文献
5.
中日规范中关于液化和侧向扩流场地桥梁桩基抗震设计考虑之比较 总被引：1，自引：0，他引：1
评述了我国液化场地和侧向扩流场地桥梁桩基抗震设计规范。总结了中日两国液化场地和侧向扩流场地桥梁桩基的抗震设计方法与技术细节,阐述了日本规范中液化场地和侧向扩流场地桥梁桩基抗震设计中的液化地基土反力折减系数的确定方法,以及土体液化侧向扩流对桩作用力的计算模式。指出我国规范中在液化和侧向扩流场地桩的抗震分析方法、不同土层分界处桩的抗震措施、桩的竖向承载力及桩的屈曲稳定性分析等方面存在的主要问题,据此给出了亟待改进的初步建议。这对我国桥梁工程的抗震安全性具有重要意义,可供我国工程技术人员参考借鉴。 相似文献
6.
基于黏弹性人工边界,建立上部结构-桩-土的共同作用三维有限元模型,分析地震作用下预应力混凝土管桩的运动响应特性。分别针对预应力混凝土管桩的桩径、双层软硬土剪切波速比值、上覆土层厚度、上部结构荷载等影响因素进行数值计算。参数分析表明:在地震作用下,桩径的增大会导致桩身整体弯矩相应增加,特别是桩身土层分界面处增大明显;软硬土层剪切波速比及上覆土层厚度的增加,引起土层分界面处桩身峰值弯矩增加;固定桩头条件下,桩头与桩身软硬土层分界面处均会产生较大的运动弯矩;上部结构的惯性荷载对固定桩头的内力有着较大影响,对桩身深处段弯矩影响较小。本文研究结论可为预应力混凝土管桩抗震设计提供有益的理论参考。 相似文献
7.
根据已经完成的液化侧向扩展场地-群桩基础-上部结构体系大型振动台试验,在有限元软件OpenSees中建立了可液化倾斜场地振动台试验的有限元模型。通过与试验结果对比,验证了数值模型的可靠性。基于此,建立了典型水平和倾斜液化场地-桩基-桥梁结构体系的数值模型,讨论了双向地震作用下水平和倾斜场地体系地震响应的差异,结果表明:相比水平场地,倾斜场地超孔隙水压力在峰值阶段波动幅度更大,土体的侧向位移增加明显,尤其是在饱和砂土中部位置;倾斜场地中桩基础的破坏程度更大,可液化层中部桩基曲率最大可增大约13倍,桩身水平位移显著增加;而水平场地桥墩曲率比倾斜场地桥墩曲率大,建议在液化场地桩基设计中应考虑场地倾斜带来的影响。 相似文献
8.
针对振动台试验,采用u-p形式控制方程表述饱和砂土的动力属性,选用土的多屈服面塑性本构模型刻画饱和砂土和黏土的力学特性,引入非线性梁-柱单元模拟桩,建立试验受控条件下液化场地群桩-土强震相互作用分析的三维有限元模型,并通过试验结果验证数值建模途径与模拟方法的正确性。以实际工程中常用的2×2群桩为例,建立桩-土-桥梁结构强震反应分析三维有限元模型。基于此,针对不同群桩基础配置对液化场地群桩-土强震相互作用影响展开具体分析。对比发现,桩的数量相同时,桩排列方向与地震波输入方向平行时比垂直时桩基受力减小5%~10%,而对场地液化情况无明显影响;相同排列形式下,三桩模型中土体出现液化的时间约比双桩模型延缓5s,桩上弯矩和剪力减小33%~38%。由此可见,桩基数量增加,桩-土体系整体刚度更大,场地抗液化性能显著,桩基对上部桥梁结构的承载性能明显增强,其安全性与可靠性更高。这对实际桥梁工程抗震设计具有一定的借鉴意义。 相似文献
9.
通过成都平原砾性土场地勘察测试,研究汶川地震中大量砾性土液化场地的基本特性,找出一般规律,对砾性土场地液化发生主客观原因提出解释,并修正以往若干认识偏差.分析表明:汶川地震液化砾性土层粒径范围宽,含砾量5%~85%甚至更大,同时其实测剪切波速140~270 m·s~(-1),修正剪切波速160~314 m·s~(-1),都远超历史记录;液化砾性土场地1/2集中在Ⅷ度区内,表明如砂土层液化一样,砾性土场地大规模液化需要较强地震动触发,但超过触发强度后液化规模增长均有限;成都平原浅表地层二元基本结构是汶川地震中出现大量砾性土场地的客观条件之一,该结构可使饱和砾性土层处于封闭状态,构成了砾性土液化的基本条件;虽然液化砾性土层剪切波速很高,但实际上大多松散状态,是此次地震大量砾性土场地发生液化的客观条件之二;地震中地表(井中)喷出物与地下实际液化土类大相径庭,且液化层埋深大多小于6.0 m,以往以地表喷出物反推地下液化层土性类型的做法不再成立;认为砾性土层波速大、透水性好而不会液化的传统认识也不再成立,但砾性土层液化条件与砂土层液化条件不同,前者要求更高. 相似文献
10.
基于相同土层结构地基条件下,分别采用低承台群桩-独柱墩与高承台群桩-独柱墩结构,完成了两次可液化场地群桩-土-桥梁结构地震反应振动台试验,据此研究了承台型式对桥梁桩-柱墩地震反应的影响。研究表明,与高承台桩相比,可液化场地中低承台桩的抗震性能更优;地震中砂层尚未液化或液化不充分时,低承台更多表现出减弱桩尤其桩上段的加速度反应的作用,相反高承台更多起到放大桩的加速度作用,而高承台桩与低承台桩的峰值应变自下而上更多表现出逐渐增大趋势;即使砂层完全液化时,低承台桩的峰值应变自下而上仍以渐增为主;与低承台桩相比,高承台桩更有助于放大墩顶加速度、位移反应,对结构体系整体稳定性产生了不良影响;虽然低承台桩未出现严重破坏,但砂层中部桩的应变却很大,液化砂土-桩运动相互作用对桩的抗震性能影响不容忽视。 相似文献
11.
Shake table test of soil-pile groups-bridge structure interaction in liquefiable ground 总被引：2，自引：1，他引：1
<正>This paper describes a shake table test study on the seismic response of low-cap pile groups and a bridge structure in liquefiable ground.The soil profile,contained in a large-scale laminar shear box,consisted of a horizontally saturated sand layer overlaid with a silty clay layer,with the simulated low-cap pile groups embedded.The container was excited in three E1 Centra earthquake events of different levels.Test results indicate that excessive pore pressure(EPP) during slight shaking only slightly accumulated,and the accumulation mainly occurred during strong shaking.The EPP was gradually enhanced as the amplitude and duration of the input acceleration increased.The acceleration response of the sand was remarkably influenced by soil liquefaction.As soil liquefaction occurred,the peak sand displacement gradually lagged behind the input acceleration;meanwhile,the sand displacement exhibited an increasing effect on the bending moment of the pile,and acceleration responses of the pile and the sand layer gradually changed from decreasing to increasing in the vertical direction from the bottom to the top.A jump variation of the bending moment on the pile was observed near the soil interface in all three input earthquake events.It is thought that the shake table tests could provide the groundwork for further seismic performance studies of low-cap pile groups used in bridges located on liquefiable groun. 相似文献
12.
Bridges are a part of vital infrastructure,which should operate even after a disaster to keep emergency services running.There have been numerous bridge failures during major past earthquakes due to liquefaction.Among other categories of failures,mid span collapse(without the failure of abutments)of pile supported bridges founded in liquefiable deposits are still observed even in most recent earthquakes.This mechanism of collapse is attributed to the effects related to the differential elongation of natural period of the individual piers during liquefaction.A shake table investigation has been carried out in this study to verify mechanisms behind midspan collapse of pile supported bridges in liquefiable deposits.In this investigation,a typical pile supported bridge is scaled down,and its foundations pass through the liquefiable loose sandy soil and rest in a dense gravel layer.White noise motions of increasing acceleration magnitude have been applied to initiate progressive liquefaction and to characterize the dynamic features of the bridge.It has been found that as the liquefaction of the soil sets in,the natural frequency of individual bridge support is reduced,with the highest reduction occurring near the central spans.As a result,there is differential lateral displacement and bending moment demand on the piles.It has also been observed that for the central pile,the maximum bending moment in the pile will occur at a higher elevation,as compared to that of the interface of soils of varied stiffness,unlike the abutment piles.The practical implications of this research are also highlighted. 相似文献
13.
Observations of pile foundation performance during previous earthquakes have shown that pile failure has been caused by lateral ground movements resulting from soil liquefaction. The recognition that lateral ground movements may play a critical role in pile performance during an earthquake has important implications for design and risk assessment, and requires that analytical models be devised to evaluate these potential problems.In this paper, parametric studies were conducted to estimate the maximum bending moments induced in piles subjected to lateral ground displacement. The results are summarized in charts using dimensionless parameters.The analyses reveal that the existence of a nonliquefiable layer at the ground surface can affect significantly the maximum bending moment of the pile. When a relatively thick nonliquefiable layer exists above a liquefiable layer, neither the material nonlinearity of the soil nor loss of soil stiffness within the liquefiable layer significantly affect the maximum bending moment. When the thickness of the liquefiable soils is greater than about three times that of an overlying intact layer, soil stiffness in the liquefiable layer must be chosen carefully when evaluating the maximum bending moment. 相似文献
14.
Remediation of piled foundations against lateral spreading by passive site stabilization technique 总被引：2，自引：0，他引：2
Ahmet Pamuk Patricia M. Gallagher Thomas F. Zimmie 《Soil Dynamics and Earthquake Engineering》2007,27(9):864-874
Physical modeling tests were conducted on pile foundations to measure the seismic performance of a new ground improvement technology, called passive site stabilization, for use on sites susceptible to liquefaction and liquefaction-induced lateral spreading. The method involves the slow injection of a low-viscosity stabilizer in conjunction with the natural groundwater flow. The effectiveness of the treatment using dilute colloidal silica as the stabilizer was tested by two centrifuge models that simulated soil–pile interaction of a 2×2 end-bearing pile group embedded in a multilayer soil deposit of 10-m thickness. The models utilized a laminar box and involved gently inclined soil profiles with and without the applied soil improvement. Response of the pile groups and the lateral spreading behaviors of the treated and untreated soil under a simulated base shaking were investigated and compared. The results showed that treatment with dilute colloidal silica stabilizer minimized permanent lateral deformations and reduced the liquefaction potential of the soil. Significant reductions occurred in the measured pile bending moments and axial forces because the layer treated with dilute colloidal silica did not liquefy. Thus, the technique can be an alternative to traditional methods of ground improvement. 相似文献
15.
To investigate the seismic response of a pile group during liquefaction, shaking table tests on a 1/25 scale model of a 2 × 2 pile group were conducted, which were pilot tests of a test project of a scale-model offshore wind turbine with jacket foundation. A large laminar shear box was utilized as the soil container to prepare a liquefiable sandy ground specimen. The pile group model comprising four slender aluminum piles with their pile heads connected by a rigid frame was designed with similitude considerations focusing on soil–pile interaction. The input motions were 2-Hz sinusoids with various acceleration amplitudes. The excess pore water pressure generation indicated that the upper half of the ground specimen reached initial liquefaction under the 50-gal-amplitude excitation, whereas in the 75-gal-amplitude test, almost entire ground was liquefied. Accelerations in soil, on the movable frames composing the laminar boundary of the shear box, and along the pile showed limited difference at the same elevation before liquefaction. After liquefaction, the soil and the movable-frame accelerations that represented the ground response considerably reduced, whereas both the movable frames and the piles exhibited high-frequency jitters other than 2-Hz sinusoid, and meantime, remarkable phase difference between the responses of the pile group and the ground was observed, all probably due to the substantial degradation of liquefied soil. Axial strains along the pile implied its double-curvature bending behavior, and the accordingly calculated moment declined significantly after liquefaction. These observations demonstrated the interaction between soil and piles during liquefaction. 相似文献
16.
R. Uzuoka M. Cubrinovski H. Sugita M. Sato K. Tokimatsu N. Sento M. Kazama F. Zhang A. Yashima F. Oka 《Soil Dynamics and Earthquake Engineering》2008,28(6):436-452
The 1995 Kobe earthquake seriously damaged numerous buildings with pile foundations adjacent to quay walls. The seismic behavior of a pile group is affected by movement of quay walls, pile foundations, and liquefied backfill soil. For such cases, a three-dimensional (3-D) soil–water coupled dynamic analysis is a promising tool to predict overall behavior. We report predictions of large shake table test results to validate 3-D soil–water coupled dynamic analyses, and we discuss liquefaction-induced earth pressure on a pile group during the shaking in the direction perpendicular to ground flow. Numerical analyses predicted the peak displacement of footing and peak bending moment of the group pile. The earth pressure on the pile in the crustal layer is most important for the evaluation of the peak bending moment along the piles. In addition, the larger curvatures in the bending moment distribution along the piles at the water side in the liquefied ground were measured and predicted. 相似文献
17.
Soil liquefaction induced by earthquakes frequently cause costly damage to pile foundations. However, various aspects of the dynamic behavior and failure mechanisms of piles in liquefiable soils still remain unclear. This paper presents a shake-table experiment conducted to investigate the dynamic behavior of a reinforced-concrete (RC) elevated cap pile foundation during (and prior to) soil liquefaction. Particular attention was paid to the failure mechanism of the piles during a strong shaking event. The experimental results indicate that decreasing the frequency and increasing the amplitude of earthquake excitation increased the pile bending moment as well as the speed of the excess pore pressure buildup in the free-field. The critical pile failure mode in the conducted testing configuration was found to be of the bending type, which was also confirmed by a representative nonlinear numerical model of the RC pile. The experimental results of this study can be used to calibrate numerical models and provide insights on seismic pile analysis and design. 相似文献
18.
Numerical analysis of an infinite pile group in a liquefiable soil was considered in order to investigate the influence of pile spacing on excess pore pressure distribution and liquefaction potential. It was found that an optimal pile spacing exists resulting in minimal excess pore pressure. It was also found that certain pile group configurations might reduce liquefaction potential, compared to free field conditions. It was observed that for closely spaced piles and low frequency of loading, pile spacing has little influence on the response of the superstructure. 相似文献