共查询到18条相似文献，搜索用时 125 毫秒
1.
穿过郯庐断裂带中段（沂沭断裂带,36°N）所做的大地电磁测深（MT）剖面长约150km.使用Robust技术和远参考道大地电磁方法处理观测数据.通过分析视电阻率、阻抗相位、Swift二维偏离度和区域走向,定性确定测区的电性结构.二维反演解释中选择非线性共轭梯度（NLCG）方法,使用TE、TM两种模式资料联合反演,沿剖面的二维电性结构显示：自西向东,鲁西隆起、郯庐断裂带、胶莱坳陷及鲁东隆起4个电性区块分别对应,鲁东和鲁西隆起区为高阻,郯庐断裂带电性结构复杂,高、低阻相间,胶莱坳陷为低阻（高导）区.沿MT剖面附近曾发生3个地震,其震源区处在电性变化剧烈部位,并在震源区附近存在高导体. 相似文献
2.
就采用地球物理探测、地质岩石学分析和高温高压实验(GGE)综合研究区域地壳细结构和确定地震震源区的可能性和方法作了探讨,并以临汾地区为例,给出了实施过程中的一些具体考虑.这些考虑包括:通过地球物理探测建立地壳、上地幔的速度、电性、密度、磁性和热等结构,给出深部的温压分布等;通过地质调查、钻探和岩石学分析确定沉积层的性质与厚度、结晶基底的组成,推测深部物质的状态,选取典型样品等;在模拟深部温压条件下,通过对岩石波速、电性和密度等的测定和与地球物理结构模型、地质岩石学结构模型进行综合比较建立区域地壳三维结构,通过对岩石力学行为的实验测定与了解,选择发震判据,确定潜在震源区. 相似文献
3.
吴一凡 《地震地磁观测与研究》2018,39(3):76-80
研究表明,同一区域地电暴记录与地磁场变化率在形态、幅度及周期成分上呈现出较强的相关性。采用磁暴期间电磁场观测数据,基于一维水平层状电性介质模型对地电暴波形进行拟合,反演地下介质电性结构。结果表明,地电暴拟合波形与观测记录一致性较好,利用反演确定的大地电性结构参数和其他磁暴事件,计算得到的理论感应地电场与观测结果相符合。 相似文献
4.
郯庐断裂带中段的沂沭断裂带发生过多次中强地震,其结构复杂,是地震研究者重点关注的区域。山东安丘和莒县电磁台都具有综合地电场和地磁场观测,两台分别位于沂沭断裂带内的安丘-莒县断裂和昌邑-大店断裂上。山东无棣电磁台位于郯庐断裂带西侧,属冀东-渤海断块,距安丘台230km,但此前未曾对该台站的地壳深部电性结构进行过探测研究。文中利用大地电磁测深方法(MT)对这3个电磁台站及其附近区域的探测数据进行研究,结果表明,3个台站的地壳电性结构有明显的差别,分别与台站区域地质构造及其地震活动性存在对应关系。在每个台站及其附近的4个测点分别得到优良的视电阻率和阻抗相位等数据,经过一维和二维反演,获得了3个台站的地壳深部电性结构,并可与直流对称四级电阻率测深法得到的近地表的电性结构进行对比。无棣台及其附近具有稳定地块的成层性地壳深部结构,而安丘和莒县电磁台分别具有复杂的地壳电性结构,呈现出活动地块边界带的结构特点。安丘台和莒县台附近区域可分别以安丘-莒县断裂和昌邑-大店断裂为界,将地壳电性结构分成2部分,在断裂西侧即郯庐断裂带内部的中下地壳低阻层更发育,昌邑-大店断裂西侧的低阻体可能含丰富的流体,在区域的地震孕育发展过程中起着重要作用。 相似文献
5.
带地形的大地电磁二维正演数值模拟多数基于电性各向同性理论,由于地球内部电性各向异性现象的普遍存在,基于电性各向异性理论研究地形起伏情况下大地电磁二维正演数值模拟就显得非常迫切.本文首先由麦克斯韦方程出发,引入张量电导率,求得一组关于平行走向的电场分量Ex和磁场分量Hx的二阶偏微分方程,使用有限差分法求解出Ex和Hx的近似解,并以此求得其他场分量;其次,引入地形因素,改变变量在网格节点中的排列方式,选择交错排列方式从而给有限差分系数矩阵的最大带宽分配合理的存储空间;最后,使用Weaver的方法解决TM模式下,在地-空分界面垂直于构造走向的一些区域存在不同电导率的问题.通过对带地形的二维电性各向异性结构做正演模拟,研究地形因素对大地电磁响应的影响;以电性各向异性理论为基础,将地形因素引入对实测大地电磁资料的处理中,通过做二维正演拟合和未引入地形因素的结果做对比,说明电性各向异性现象的普遍存在,认识地形因素对观测大地电磁场的影响,为今后分析解释实测大地电磁资料包含地形因素和电性各向异性情况提供理论基础和技术指导. 相似文献
6.
九瑞矿集区作为全国重点整装勘查区之一,深部找矿工作一直是研究重点和热点.本文在综合分析研究区区域地质资料、对典型地层和岩石标本进行电阻率参数测试和统计分析的基础上,利用研究区面积性AMT数据进行三维电性结构研究.为获得AMT最佳反演参数,选择一条典型AMT剖面开展二维非线性共轭梯度(NLCG)反演,进而总结出利用TM极化模式数据、拉格朗日乘子等于3的二维反演方案.综合利用地质、钻探和电性特征对全区23条AMT剖面进行二维约束反演,并将所有测线的电阻率反演结果三维网格化,得到了研究区的三维电性结构.最后,我们通过对三维电性结构的综合分析,确定研究区地下地层、岩体展布、断裂构造分布特征以及基底起伏情况.与已知矿床对比,我们发现浅部北西断裂与北东向区域性深部断裂交汇处、基底隆起凹槽边缘以及岩体边缘为成矿有利区. 相似文献
7.
在青藏高原东北缘至鄂尔多斯地块沿玛沁—兰州—靖边剖面进行62个测点的大地电磁观测,采用Robust技术对观测数据进行了处理和张量阻抗分解.分析了视电阻率和阻抗相位曲线、二维偏离度、区域走向.采用RRI二维反演技术进行了资料的反演解释,二维剖面的电性结构显示：（1）玛沁断裂带、兰州深断裂带、马家滩—大水坑断裂带将剖面分为4个电性区块：巴颜喀拉地块、秦祁地块、边界带和鄂尔多斯地块.（2）区块1、2和4的地壳电性结构有类似特点：上地壳为高阻层,下地壳上部为低阻带,下地壳下部到上地幔电阻率随深度逐渐升高.区块3电性成层性差、结构复杂,是现今构造活动较强烈的地区.（3）玛沁断裂带、海原断裂带和罗山—云雾山断裂带为较陡立的超壳断裂带;西秦岭北缘断裂带为壳内断裂带. 相似文献
8.
交错模型指的是由几组走向不同的线性构造（近似二维）在空间（纵向、横向）上组合而成的模型.对于电性结构,交错模型表现为纵向或横向上的构造存在电性主轴方位的变化.从构造维性的角度来看,交错模型是一种由二维模型组合而成的特殊的三维模型,直接对其进行大地电磁二维反演,不易获得可靠的反演结果.本文针对交错模型的特点,提出分频段-分区段反演方案.该方案首先需要借助于阻抗张量成像技术,在频率域确定组成交错模型的各线性构造的电性主轴,然后,针对不同的频段、区段,选择对应电性主轴的数据进行反演,通过初始模型的构建将不同电性主轴方位的反演结果对接起来.本文通过三维理论模型的研究,系统展示了分频段-分区段反演的全过程,归纳得到：在分频段反演时先做低频段反演,在分区段反演时先做二维性更不显著一侧的反演.最后,本文将这一技术用于郯庐断裂带中南段一条实测剖面的反演中,其结果与常规二维反演结果相比较,深部的信息更为丰富,且与其他已有地质、地球物理结果的可对比性更好,表明在构造复杂地区,大地电磁分频段-分区段二维反演具有较高的模型分辨率和可靠性. 相似文献
9.
本文通过对高密度电阻率法勘探中的长测线多排列数据进行连接处理,实现了同一测线采用同一套参数的规范化处理,克服了因不同排列采用不同参数处理而导致假异常和信息丢失等弊端,同时解决了在成像时,因各个电性剖面的色标值不一致,剖面坐标与实际桩号对应不直观,导致对整个区域的电性趋势认识产生误导的问题.从实例处理来看,能为整个勘探区提取更丰富的电性信息,不但突出了整条测线的地下电性趋势,更客观、更全面地把握和认识勘探地区的电性分布规律,而且从宏观上把握了一些比较隐蔽的地质现象. 相似文献
10.
11.
基于大地电磁阻抗张量分解技术,本文提出了两种电性主轴方位的统计描述图像：随频率变化的统计分布成像（频率分布云图）和随测点序列变化的统计分布成像（测点分布云图）.这两种图像与传统的统计玫瑰图一起,较全面地描述了最佳主轴的分布特征.在进行构造维性分析过程中,通过定义二维有效因子e2d,来压制一维结构和三维结构、突出纯二维结构的影响.e2d被用于电性主轴的统计加权,有效地起到了滤波的作用;同时,统计成像中还考虑了数据质量的影响.为了得到稳定、高质量的区域阻抗张量数据,提出并实现了共主轴的多测点-多频点阻抗张量分解新算法.最终,完成了以上各项处理手段的可视化实现.本文通过两个理论模型和一个实测算例,以共轭阻抗法（CCZ法）为基础,展示了这一新技术的有效性. 相似文献
12.
本文针对Groom-Bailey分解法在消除地表电性不均匀体对MT数据的畸变效应时存在的问题引入遗传算法,对基于传统线性最优化方法的GB分解算法进行改进,提出基于遗传算法的大地电磁阻抗张量分解方法.通过对理论合成数据以及三维/二维模型正演数据的分解试验,并且对青藏高原北缘阿尔金断裂地区实际MT数据进行分解处理,证明了基于遗传算法的GB分解能够更加有效地校正三维/二维情况下近地表三维电性不均匀体所造成的畸变影响.最后,在已有算法基础上,研究了基于遗传算法的多频率GB分解算法和MT数据静校正算法,并通过实际MT数据的处理证明了这些算法的有效性. 相似文献
13.
横过松嫩地块东缘和佳木斯地块西缘的大地电磁测深剖面揭示了两块体结合带附近的深部电性结构.本文对剖面测点做了标准化数据处理,并对二维偏离度、构造走向进行了计算和分析,采用非线性共轭梯度(NLCG)二维反演方法对TM模式的数据进行了反演,获得了该剖面的地壳、上地幔电性结构模型,划分出三个典型构造单元:松嫩地块东缘、碰撞拼合带和佳木斯地块西缘.研究结果表明,研究区上地壳基本呈高阻特征,可能为岩浆岩,代表其经历了多期次岩浆作用,而松嫩地块东缘和佳木斯地块西缘的中下地壳的高导体可能与地幔物质的上涌有关;拼合带下方存在西倾的高导体和高阻体,可能是佳木斯地块向西俯冲到松嫩地块下方的构造遗迹;研究区可能发生了拆沉作用,与之伴随的地幔物质上涌可能是后期伸展作用的一个动力. 相似文献
14.
The Yurihara oil and gas field is located on the southern edge of Akita Prefecture, northeastern Japan. In this area, drilling, surface geological surveys and many seismic surveys have been used to investigate the geological structure. Wells drilled into the Nishikurosawa Basalt Group (NBG) of Miocene age found oil and gas reservoirs at depths of 1.5–2 km. Oil and gas are now being produced commercially and further exploration is required in the surrounding areas. However, since the neighbouring areas are covered with young volcanic products from the Chokai volcano, and have a rough topography, the subsurface distribution of the NBG must be investigated using other methods in addition to seismic reflection. According to the well data, the resistivity of the NBG is comparatively higher than that of the overlying sedimentary formations, and therefore the magnetotelluric (MT) method is expected to be useful for the estimation of the distribution of the NBG. An MT survey was conducted along three survey lines in this area. Each line trended east–west, perpendicular to the regional geological strike, and was composed of about 25 measurement sites. Induction vectors evaluated from the magnetic field show that this area has a two-dimensional structure. The evaluated resistivity sections are in agreement with the log data. In conclusion, we were able to detect resistive layers (the NBG) below conductive layers. The results indicate that the NBG becomes gradually less resistive from north to south. In the centre of the northern line, an uplifted resistive area is interpreted as corresponding to the reservoir. By comparison with a seismic section, we prove the effectiveness of the integration of seismic and MT surveys for the investigation of the morphology and internal structure of the NBG. On other survey lines, the resistive uplifted zones are interpreted as possible prospective areas. 相似文献
15.
Summary The MT method is applied to the study of a buried graben in the western Canadian sedimentary basin. Tensor analysis and two dimensional numerical modeling techniques were applied as an aid to the interpretation. The results obtained indicate the presence of a buried geoelectric structure and the need of interpreting MT apparent resistivity curves in terms of the regional geology and major structural features which are not necessarily one dimensional. 相似文献
16.
María de los Ángeles García Juanatey Juliane Hübert Ari Tryggvason Laust B. Pedersen 《Geophysical Prospecting》2013,61(1):200-219
New magnetotelluric (MT) data from two perpendicular profiles in the Kristineberg area, northern Sweden, were analysed and modelled. In the Skellefte Ore District, the Kristineberg volcanic hosted massive sulphide (VHMS) deposit mine is one of the largest and deepest (1250 m). Seventeen broadband magnetotelluric stations were installed along two existing seismic reflection lines. The profiles were 6 and 12 km long with 500 m and 1 km site spacing, respectively. The obtained MT transfer functions in the period range of 0.0015–200 s are of fairly good quality. Detailed strike and dimensionality analysis reveal consistent but period dependent, strike directions, indicating a change in the geoelectrical strike with depth. From the two‐dimensional inversion of the determinant of the impedance tensor, two stable conductivity models with good data fit were obtained. The addition of seismic reflection information from the co‐located survey, improved the data fit of one of them. Extensive sensitivity analyses helped to delineate the well resolved regions of the models and to determine the position of pronounced boundaries. The results are in good agreement with previous studies, especially regarding the presence of a deep conductor interpreted as a structural basement to the district. They also reveal with more detail the configuration of the main geological units of the Skellefte Ore District, especially of the ore bearing volcanic rocks and the embedded alteration zones. 相似文献
17.
G. Michael Hoversten 《Geophysical Prospecting》1996,44(6):935-961
Hydrocarbon exploration in the Papuan fold belt is made extremely difficult by mountainous terrain, equatorial jungle and thick karstified Miocene limestones at the surface. The high-velocity karstified limestones at or near the surface often render the seismic technique useless for imaging the subsurface. In such areas magnetotellurics (MT) provides a valuable capability for mapping subsurface structure. The main structural interface which can be mapped with MT, due to the large electrical contrast, is the contact between the resistive Darai limestone and the underlying conductive sediments of the Ieru Formation. In some areas the base of the Darai can be mapped with reasonable accuracy by fitting 1D models to the observed MT data. However, in many cases where 2D and 3D effects are severe, 1D interpretations can yield dramatically incorrect results. Numerical and field data examples are presented which demonstrate the severity of the 1D errors and the improvements in accuracy which can be achieved using a 2D inverse solution. Two MT lines over adjacent anticlines, both with well control and seismic data, are used to demonstrate the application of 1D and 2D inversions for structural models. In both cases the seismic data provide no aid in the interpretations. The example over the Hides anticline illustrates a situation where 1D inversion of either TE or TM mode provides essentially the same depth to base of Darai as 2D inversion of both TE and TM. Both models provide base Darai depth estimates which are within 10% of that measured in the well. The example over the Angore anticline illustrates the inadequacy of 1D inversion in structurally complex geology complicated by electrical statics. The TE mode fits a 1D Darai thickness of 800 metres while the TM mode fits a 1D Darai thickness of 3500 metres, bracketing the thickness of 2450 metres observed in the well. The final 2D inversion model provides a depth estimate of 2250 metres. Four MT lines along the Angore anticline have been interpreted using 2D inversion. A high degree of correlation exists between lineaments observed on an airborne radar image and zones of low resistivity within the high-resistivity material interpreted as Darai limestone. These low-resistivity zones are interpreted as fault zones. Three-dimensional modelling has been used to simulate 3D statics in an otherwise 2D earth. These data were used to test the Groom-Bailey (GB) decomposition for possible benefits in reducing static effects and estimating geoelectric strike in the Papua New Guinea (PNG) field data. It has been found that the GB decomposition can provide improved regional 2D strike estimates in 3D contaminated data. However, in situations such as PNG, where the regional 2D strike is well established and hence can be fixed, the GB decomposition provides apparent resistivities identical to those simply rotated to strike. 相似文献
18.
假定垂直轴为二维对称各向异性介质主轴之一，构造走向与另一主轴方向成任一夹角，用伽勒金（Ｇａｌｅｒｋｉｎ）有限元法和矩形网格，优化地合成总体刚度矩阵，使二维各向异性介质的基本方程形成有限元代数方程组，求出各节点场值，并利用ＭＯＭ法求出辅助场，进而求出张量阻抗等响应函数．同时还对有关文献的计算模型进行了数值模拟检验 相似文献