共查询到18条相似文献，搜索用时 93 毫秒
1.
地震作用下钢筋混凝土（RC）桥墩容易损坏。为完善RC桥墩的抗震设计及验算方法,对比最新中国和欧洲规范中关于RC桥墩的延性抗震设计及验算方法的不同之处。基于Midas/Civil软件所建立的常规连续梁桥有限元模型,对比分析采用中欧规范开展的RC桥墩延性抗震设计及验算结果。结果表明:中欧规范中关于RC桥墩的延性抗震设计理念、抗剪和变形验算方法及延性构造细节均有区别。基于中欧规范设计的RC桥墩配筋情况存在差异。与中国规范相比,欧洲规范关于RC桥墩的横向钢筋配筋率和纵筋最小配筋率要求较高,有利于保证结构的抗剪强度和延性;箍筋最大间距要求较低,不利于防止纵筋压曲。 相似文献
2.
近断层地震动作用下钢筋混凝土桥墩的抗震性能 总被引：9，自引：2，他引：9
通过对满足规范延性要求的12根典型钢筋混凝土桥墩试件的线性和非线性地震反应分析，指出在近断层地震动作用下满足延性需求与延性能力比小于1.0的桥墩仍可能发生严重破坏和倒塌，若考虑桥墩的地震损伤性能，允许的延性需求与延性能力比不宜超过0.6-0.8。讨论了桥墩延性抗震设计中强度折减系数Rμ和设计基底剪力系数BSC取值问题。 相似文献
3.
以墩顶漂移率为指标运用ABAQUS有限元软件对钢筋混凝土桥墩进行地震易损性分析。对钢筋混凝土桥墩模型进行精细网格划分，运用循环往复Pushover方法模拟钢筋混凝土桥墩破坏界限值，以此界限值为标准对轴压比为0.20、0.22、0.24、0.26和0.30钢筋混凝土桥墩进行增量动力分析（IDA）。研究结果表明:结构的破坏超越概率，随着轴压比的增大而增大；考虑钢筋混凝土桥墩延性抗震性能，设计轴压比不宜超过0.30；轴压比为0.24~0.26时，钢筋混凝土桥墩破坏概率增加不大，宜为合理的轴压比。 相似文献
4.
钢管混凝土桥墩抗震性能试验研究 总被引：1，自引：0，他引：1
为研究钢管混凝土桥墩的抗震性能,对钢管混凝土桥墩和钢筋混凝土桥墩进行了拟静力对比试验研究。根据试件的破坏发展过程以及各试件的滞回曲线和骨架曲线,分析了其滞回性能、耗能能力、延性、强度退化及刚度退化等抗震性能。试验结果表明,钢管混凝土桥墩的抗震性能明显好于钢筋混凝土桥墩。在含钢率和轴力相同的情况下,钢管混凝土桥墩的滞回曲线比钢筋混凝土桥墩丰满得多,前者的耗能能力约为后者的4.46倍,钢管混凝土桥墩的延性大于钢筋混凝土桥墩;随着轴压比的增大,钢管混凝土桥墩延性有所下降,强度退化加快,但对其刚度退化的影响不大。 相似文献
5.
基于位移设计的钢筋混凝土桥墩抗震性能试验研究(Ⅰ):拟静力试验 总被引：2，自引：0，他引：2
通过拟静力试验研究了基于位移设计钢筋混凝土桥墩的抗震性能。利用基于位移抗震设计方法和桥梁抗震规范方法设计了各2根和1根1：2．5比例钢筋混凝土桥墩试件,对低周反复荷载作用下试件试验破坏形态、承载力、位移延性、滞回耗能、刚度退化等方面进行了比较分析,可以认为基于位移设计的钢筋混凝土桥墩能够达到预期的延性抗震要求,并且在相对耗能能力（与理想弹塑性模型相比）、刚度退化性能方面与现行规范抗震设计方法设计的桥墩相当。试验表明建议的钢筋混凝土桥墩基于位移的抗震设计方法是实际可行的。 相似文献
6.
基于位移设计的钢筋混凝土桥墩抗震性能试验研究(I):拟静力试验 总被引：2，自引：0，他引：2
通过拟静力试验研究了基于位移设计钢筋混凝土桥墩的抗震性能。利用基于位移抗震设计方法和桥梁抗震规范方法设计了各2根和1根1:2.5比例钢筋混凝土桥墩试件,对低周反复荷载作用下试件试验破坏形态、承载力、位移延性、滞回耗能、刚度退化等方面进行了比较分析,可以认为基于位移设计的钢筋混凝土桥墩能够达到预期的延性抗震要求,并且在相对耗能能力(与理想弹塑性模型相比)、刚度退化性能方面与现行规范抗震设计方法设计的桥墩相当。试验表明建议的钢筋混凝土桥墩基于位移的抗震设计方法是实际可行的。 相似文献
7.
基于位移设计的钢筋混凝土桥墩抗震性能试验研究(Ⅱ):振动台试验 总被引：1，自引：1，他引：0
通过模型振动台试验研究了基于位移设计的钢筋混凝土桥墩的抗震性能。以完成的拟静力试验中的桥墩试件为参考原型,利用基于位移抗震设计方法和现行桥梁抗震规范方法设计了4根1:2的钢筋混凝土桥墩试件并进行了模型振动台试验。对小震、中震和大震作用下桥墩试件的破坏形态、加速度和位移反应、位移延性系数和地震总输入能(耗能)等方面进行了比较分析。综合拟静力试验和振动台试验结果,可以认为基于位移设计的钢筋混凝土桥墩能够达到预期的延性抗震要求。 相似文献
8.
碳纤维布增强钢筋混凝土柱延性性能的评估与分析 总被引：2，自引：0，他引：2
在试验研究的基础上，对碳纤维布提高钢筋混凝土柱延性的机理进行了分析，确定了碳纤维布用量、轴压比、剪跨比、矩形截面柱转角部位的形状等试验因素对碳纤维布加固钢筋混凝土柱延性的影响规律。在此基础上，重点对碳纤维布加固钢筋混凝土柱延性性能的评估与分析方法进行了研究，提出了碳纤维布加固矩形截面钢筋混凝土柱位移延性比的理论计算方法和简化计算公式。计算结果与试验数据能较好地吻合。工程技术人员可以应用上述方法，对碳纤维布增强钢筋混凝土柱延性性能进行合理的评估与分析。 相似文献
9.
10.
11.
Over the last two decades, the probabilistic assessment of reinforced concrete (RC) structures under seismic hazard has been developed rapidly. However, little attention has been devoted to the assessment of the seismic reliability of corroded structures. For the life‐cycle assessment of RC structures in a marine environment and earthquake‐prone regions, the effect of corrosion due to airborne chlorides on the seismic capacity needs to be taken into consideration. Also, the effect of the type of corrosive environment on the seismic capacity of RC structures has to be quantified. In this paper, the evaluation of the displacement ductility capacity based on the buckling model of longitudinal rebars in corroded RC bridge piers is established, and a novel computational procedure to integrate the probabilistic hazard associated with airborne chlorides into life‐cycle seismic reliability assessment of these piers is proposed. The seismic demand depends on the results of seismic hazard assessment, whereas the deterioration of seismic capacity depends on the hazard associated with airborne chlorides. In an illustrative example, an RC bridge pier was modeled as single degree of freedom (SDOF). The longitudinal rebars buckling of this pier was considered as the sole limit state when estimating its failure probability. The findings show that the life‐cycle reliability of RC bridge piers depends on both the seismic and airborne chloride hazards, and that the cumulative‐time failure probabilities of RC bridge piers located in seismic zones can be dramatically affected by the effect of airborne chlorides. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
12.
为探究局部锈蚀矩形截面钢筋混凝土（RC）桥墩重度震损加固后的抗震性能,本文对拟静力破坏后的6个矩形截面RC桥墩试件进行扩大截面加固。通过加载试验,对加固桥墩试件从破坏形态、滞回特性、水平承载力、位移延性、侧向刚度以及耗能等方面进行了系统分析。结果表明:相比于普通箍筋,横向施加预应力的改进扩大截面加固方式对破坏后桥墩试件的抗震性能修复成效更佳;在同等位移幅值下,锈蚀率不断增大,桥墩试件抗震性能呈现逐渐降低的趋势;钢筋锈蚀位置上移,加固后桥墩试件的抗震性能提升;轴压比加大,加固后桥墩试件承载力和侧向刚度增大,但延性降低。 相似文献
13.
This paper investigated the use of external steel jacketing for seismic retrofit of non‐ductile reinforced concrete (RC) bridge columns to prevent lap‐splice failure. Three 1/2.5‐scale specimens were tested under cyclic loads. The effectiveness of two types of steel jackets for improving the ductility and strength of specimens using inadequate transverse reinforcing and lap‐splice details were examined. An octagonal steel jacketing scheme for the seismic retrofitting of rectangular RC bridge columns was proposed. In addition, the methods for seismic retrofitting rectangular columns using elliptical steel jacketing were also critically tested. The test results indicated that the octagonal steel jackets can effectively provide confinement thereby mitigating failures as a result of inadequate transverse reinforcing and inadequate lap‐splices. Tests also confirmed that the ductility performance and the energy dissipation capacity of the specimens can be significantly improved by the octagonal steel jacket. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
14.
To investigate the seismic performance of hollow reinforced concrete(RC) bridge columns of rectangular cross section under constant axial load and cyclically biaxial bending,five specimens were tested.A parametric study is carried out for different axial load ratios,longitudinal reinforcement ratios and lateral reinforcement ratios.The experimental results showed that all tested specimens failed in the flexural failure mode and their ultimate performance was dominated by flexural capacity,which is represented by the rupture/buckling of tensile longitudinal rebars at the bottom of the bridge columns.Biaxial force and displacement hysteresis loops showed significant stiffness and strength degradations,and the pinching effect and coupling interaction effect of both directions severely decrease the structural seismic resistance.However,the measured ductility coefficient varying from 3.5 to 5.7 and the equivalent viscous damping ratio varying from 0.19 and 0.26 can meet the requirements of the seismic design.The hollow RC rectangular bridge columns with configurations of lateral reinforcement in this study have excellent performance under bidirectional earthquake excitations,and may be considered as a substitute for current hollow RC rectangular section configurations described in the Guideline for Seismic Design of Highway Bridges(JTG/T B02-01-2008).The length of the plastic hinge region was found to approach one sixth of the hollow RC rectangular bridge column height for all specimen columns,and it was much less than those specified in the current JTG/T.Thus,the length of the plastic hinge region is more concentrated for RC rectangular hollow bridge columns. 相似文献
15.
钢筋混凝土桥墩震后修复技术研究综述 总被引：1，自引：0，他引：1
介绍了近几次破坏性地震中钢筋混凝土桥墩的典型震害,总结了国内外利用FRP材料、钢套管、狗骨式杆等新型建筑材料对发生弯曲破坏、剪切破坏、纵筋搭接破坏以及空心截面桥墩的震后修复技术.研究表明,采用合适的修复方案,可以对地震损坏的桥墩进行成功修复,使其承载力和延性得到较好的恢复.文中提到的桥墩震后修复方案可为地震、火灾、爆炸以及腐蚀老化后遭受损坏的钢筋混凝土结构的修复提供参考. 相似文献
16.
17.
Experimental research and finite element analysis of bridge piers failed in flexure-shear modes 总被引：2，自引：1，他引：1
In recent earthquakes, a large number of reinforced concrete （RC） bridges were severely damaged due to mixed flexure-shear failure modes of the bridge piers. An integrated experimental and finite element （FE） analysis study is described in this paper to study the seismic performance of the bridge piers that failed in flexure-shear modes. In the first part, a nonlinear cyclic loading test on six RC bridge piers with circular cross sections is carried out experimentally. The damage states, ductility and energy dissipation parameters, stiffness degradation and shear strength of the piers are studied and compared with each other. The experimental results suggest that all the piers exhibit stable flexural response at displacement ductilities up to four before exhibiting brittle shear failure. The ultimate performance of the piers is dominated by shear capacity due to significant shear cracking, and in some cases, rupturing of spiral bars. In the second part, modeling approaches describing the hysteretic behavior of the piers are investigated by using ANSYS software. A set of models with different parameters is selected and evaluated through comparison with experimental results. The influences of the shear retention coefficients between concrete cracks, the Bauschinger effect in longitudinal reinforcement, the bond-slip relationship between the longitudinal reinforcement and the concrete and the concrete failure surface on the simulated hysteretic curves are discussed. Then, a modified analysis model is presented and its accuracy is verified by comparing the simulated results with experimental ones. This research uses models available in commercial FE codes and is intended for researchers and engineers interested in using ANSYS software to predict the hysteretic behavior of reinforced concrete structures. 相似文献
18.
钢筋混凝土分体柱的抗震机理 总被引：4，自引：0，他引：4
为揭示钢筋混凝土分体柱的抗震机理,在以前模型试验基础上,考虑隔板与单元柱之间的非线性接触及钢筋与混凝土之间的黏结滑移,数值模拟了钢筋混凝土分体柱的抗震性能。结果表明:分体柱可实现变短柱为“长”柱的设想;分体柱具有理想的变形能力和延性,延性系数达到4.0;分体柱的刚度随变形增加呈指数衰减,后期刚度退化较为缓和;分体柱具有较高的耗能能力,其耗能系数达1.44;隔板与单元柱的切向接触应力较小,可忽略隔板对单元柱的变形协调作用。进一步验证了钢筋混凝土分体柱具有理想的抗震性能,完善和发展了钢筋混凝土分体柱的设计理论和应用技术。 相似文献