首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到18条相似文献,搜索用时 140 毫秒
1.
地震反应分析中输入界面选取合理与否对设计地震动参数有重要影响。基于唐山地区钻孔剖面,分别选取剪切波速为500m/s的硬黏土和800m/s的岩石顶面作为基岩输入界面,采用一维等效线性化方法讨论中硬场地输入界面的选取对地表地震动参数的影响,结果表明:(1)地表峰值加速度放大倍数及地表加速度反应谱特征周期都随输入界面深度的增加而递增,且这种递增与输入地震动的强度及频谱特性都有密切联系;(2)随着输入界面深度的增加,地表加速度反应谱几乎全频段内增大,仅在短周期内出现减小的情况,但幅度十分有限;(3)中硬场地地震反应分析中基岩输入界面宜取剪切波速为800m/s的土层顶面。  相似文献   

2.
利用目前工程上广泛应用的一维土层地震反应计算程序对成都平原某典型卵石场地剖面进行了计算,得到了不同输入地震强度下的加速度峰值随输入界面处剪切波速增大的变化规律。结果表明,无论是地表加速度峰值,还是地下5m处的加速度峰值,在相同的地震动输入强度下,均随着输入界面处剪切波速值的增大呈对数形式增大。且在小震输入下的增加速率最快,中震输入下的增加速率次之,大震输入下增加的速率最慢。当地震动输入界面处剪切波速值从500m/s增加至800m/s时,加速度峰值均增大20%以上,最大达到32%。统计得到的二者间的经验关系式,可作为本地区具有相似场地条件工程换算加速度峰值的经验公式,为工程抗震设计人员提供参考。  相似文献   

3.
地震动输入界面的选取对深软场地地震效应的影响   总被引:4,自引:0,他引:4  
以天津和上海两个典型的深厚软弱场地为研究背景,探讨了地震动输入界面对场地地表地震动参数的影响。对于场地1(天津)和场地2(上海),分别选择7个和8个剪切波速(υs)大小不同的土层位置作为地震动输入界面,并选用Taft、Northridge地震加速度记录和南京人工波作为输入地震动,将Taft波、Northridge波和南京人工波的加速度峰值水平调整为0.35m/s^2、0.70m/s^2和0.98m/s^2,用SHAKE91程序对这两个场地进行了不同的地震动输入界面、输入地震波和峰值加速度水平的128种组合的场地地震反应分析。与从假想基岩面(υs≥500m/s)输入地震动的结果(假想的实际值)相比,可得到如下结论:(1)随着地震动输入界面深度(剪切波速)的增加,场地地表加速度反应谱逐渐地向实际值接近;(2)地震动输入界面的深度相同时,地震动加速度峰值水平越高,两者的加速度反应谱谱值的相对差异也越大;(3)对于一般建筑物,可以把剪切波速为400m/s左右的土层作为地震动输入界面;对于中长周期的建筑物,则应慎重选择地震动输入界面,最好选取υs≥500m/s^2的土层或基岩面作为地震动输入界面。  相似文献   

4.
本文选取山东地区2个Ⅲ类场地的工程地质勘探及土层剪切波速等资料,将土层厚度按5个深度段,每个分段给出了4个土层剪切波速的改变量,通过改变不同深度段土层剪切波速,建立了19种土层地震反应分析模型,分析了不同深度段,不同概率水平下土层剪切波速的变化对场地地震动参数的影响。研究表明,不同深度段土层剪切波速的变化对场地地震动参数的影响有差异。具体表现为,土层剪切波速的改变在1—10m、11—40m和地震输入界面处三个深度段对地震动加速度峰值影响较大;其中,41—70m和71—100m两个深度段剪切波速的改变对地震动加速度峰值影响小;在土层深度1—10m时,剪切波速降低,峰值变大,剪切波速的改变与峰值的改变呈负相关;在其它深度段,剪切波速降低,峰值变小,剪切波速的改变与峰值的改变呈正相关。剪切波速的改变在1—10m和11—40m两个深度段对地震加速度反应谱影响较大;在41—70m、71—100m和地震输入界面三个深度段对地震加速度反应谱影响很小。  相似文献   

5.
以Ⅱ类场地为例,选取了山东地区2个场地的工程地质勘探及剪切波速等资料,通过改变不同深度段波速,分别建立土层模型,计算分析了不同深度段、不同概率水平条件下剪切波速的变化对场地地震动参数的影响。研究结果表明,剪切波速的变化对场地地震动加速度峰值影响在浅层影响最大,基岩输入面处次之,深层最小;对特征周期的影响,在浅层影响最大,深层次之、基岩输入面处最小。研究结果为进一步研究土层剪切波速测试中的不确定性对场地地震动参数的影响及合理确定场地地震动参数提供一定的参考。  相似文献   

6.
利用日本KIK台网地表和井下地震记录验证了一维等效线性化土层地震反应程序,结果表明在土体小变形范围内,对于刚度递增型场地,程序计算结果与实际相符;而对于含软夹层或硬夹层的场地,程序计算结果与实际相差较大。据此,本文提出了一种研究软夹层和硬夹层对地表地震动影响的方法。为得到参照标准,将真实土层剖面中的夹层替换为正常土层,以满足刚度递增条件,采用土层地震反应程序计算在井下地震记录激励下的地表反应。将其与该场地地表实际地震记录进行对比分析,可得到软夹层和硬夹层对地表地震动的影响结论。本文对几个典型场地进行计算分析后得到如下结论:软夹层与硬夹层对地表地震动的影响是一致的;当夹层处于覆盖层上部时对高频地震动有较强的放大作用;当夹层处于覆盖层下部时对高频地震动有隔震作用。  相似文献   

7.
利用日本KIK台网地表和井下地震记录验证了一维等效线性化土层地震反应程序,结果表明在土体小变形范围内,对于刚度递增型场地,程序计算结果与实际相符;而对于含软夹层或硬夹层的场地,程序计算结果与实际相差较大。据此,本文提出了一种研究软夹层和硬夹层对地表地震动影响的方法。为得到参照标准,将真实土层剖面中的夹层替换为正常土层,以满足刚度递增条件,采用土层地震反应程序计算在井下地震记录激励下的地表反应。将其与该场地地表实际地震记录进行对比分析,可得到软夹层和硬夹层对地表地震动的影响结论。本文对几个典型场地进行计算分析后得到如下结论:软夹层与硬夹层对地表地震动的影响是一致的;当夹层处于覆盖层上部时对高频地震动有较强的放大作用;当夹层处于覆盖层下部时对高频地震动有隔震作用。  相似文献   

8.
选取某重要工程场地A3钻孔的厚度、剪切波速、密度等实际勘探数据,通过改变硬夹层的埋深,分析硬夹层不同埋深、不同地震时程对场地地震动参数的影响。研究结果表明:在硬夹层厚度不变和模型总厚度不变的情况下,地表水平向的峰值加速度随硬夹层埋深的增大而增大,但增幅逐渐减小;硬夹层埋深到达一定深度时不再影响地表水平峰值加速度;随着硬夹层埋深的增加,整个反应谱的谱值普遍增大。  相似文献   

9.
剪切波速对场地地表地震动参数的影响   总被引:3,自引:2,他引:1  
本文以江淮地区典型场地资料为原型,将土层剪切波速实测值按照一定比例进行增减,构造多种场地土层地震反应分析模型,选择Taft、E1centro和Kobe三条强震记录作为地震输入,采用一维频域等效线性化波动方法进行了土层地震反应分析.研究结果表明,剪切波速的变异性与场地地表地震动的影响程度与输入基岩地震动的频谱特性、幅值、土层结构等因素有关.地表峰值加速度随着剪切波速的增大而逐渐增大,地表加速度反应谱的特征周期随着剪切波速的增大而逐渐减小.  相似文献   

10.
采用Shake 2000程序,以Turkey Flat试验场地为模型,通过输入不同类型下多种强度的地震波,计算研究多工况下剪切波速测试标准差对地表加速度反应谱和峰值加速度的影响。结论为:(1)浅硬场地上剪切波速测试标准差对地震动的影响很大,影响程度与输入地震波的强度和频率以及场地剪切波速计算值有关;(2)如果将反应谱残差大于20%或加速度峰值差别大于20%定义为统计意义上的不可忽略,那么剪切波速测试标准差对计算结果的影响在大多数情况下均不可忽略;(3)当输入波的卓越周期与场地特征周期接近时,浅硬场地上剪切波速测试标准差引起的反应谱变化非常显著;(4)只有当输入波的卓越周期与场地特征周期相差较大且输入波强度偏小时,剪切波速测试标准差引起的反应谱变化才可略去;(5)当浅硬场地上剪切波速实测结果低于统计均值时,地震动计算结果的偏差一般明显大于剪切波速实测结果,高于统计均值时引起的偏差,且地震输入越强表现越明显。  相似文献   

11.
Shear wave velocity–depth information is required for predicting the ground motion response to earthquakes in areas where significant soil cover exists over firm bedrock. Rather than estimating this critical parameter, it can be reliably measured using a suite of surface (non-invasive) and downhole (invasive) seismic methods. Shear wave velocities from surface measurements can be obtained using SH refraction techniques. Array lengths as large as 1000 m and depth of penetration to 250 m have been achieved in some areas. High resolution shear wave reflection techniques utilizing the common midpoint method can delineate the overburden-bedrock surface as well as reflecting boundaries within the overburden. Reflection data can also be used to obtain direct estimates of fundamental site periods from shear wave reflections without the requirement of measuring average shear wave velocity and total thickness of unconsolidated overburden above the bedrock surface. Accurate measurements of vertical shear wave velocities can be obtained using a seismic cone penetrometer in soft sediments, or with a well-locked geophone array in a borehole. Examples from thick soil sites in Canada demonstrate the type of shear wave velocity information that can be obtained with these geophysical techniques, and show how these data can be used to provide a first look at predicted ground motion response for thick soil sites.  相似文献   

12.
The shear wave velocity is one of the important parameters in seismic engineering.The common mathematical models of relationship between shear wave velocity and depth of soil-layers are linear function model,quadratic function model,power function model,cubic function model,and quartic function model.It is generally believed that the regression formulae based on aforementioned mathematical models are mainly used for preliminary estimation of the local shear wave velocity.In order to increase the value of test data of wave speed in boreholes,the calculation formulae for the thickness of ground cover layer are derived based on the aforementioned mathematical models and their fitting parameters.The calculation formulae for the mean shear wave velocity of soil-layers are derived by integral mean value theorem.Accordingly,the calculation formulae for the equivalent shear wave velocity of soil-layers are derived.The calculation formulae for the depth of reflective waves in time-depth conversion of the reflection seismic exploration are derived.Through the statistical analysis of test data of shear wave velocity of soil layers in Changyuan County,Henan Province,regression formulae and their fitting parameters of aforementioned mathematical models are obtained.The results show that in the determination of the quality of these regression formulae and their fitting parameters,the adjusted R-square,root mean square error and residual error,the matching on the statistical range between the geometry of function of mathematical models used and the scattergram of the measured data,the application purpose and the simplicity of the regression formulae should be considered.With the aforementioned new formulae,the results show that the calculated values of equivalent shear wave velocity of soil-layers and thickness of ground cover layer meet the engineering needs.The steps for statistics and applications of the relationship between shear wave velocity and depth of soil-layers for a new area are as follows:(1) Analyze the relevant data about the site such as the drilling and wave speed test data,etc.and divide the site into seismic engineering geological units;(2) In a single seismic engineering geological unit,make statistical analysis of the data of borehole wave speed test,comprehensively identify and select mathematical models and their fitting parameters of the relationship between shear wave velocity and depth of soil-layers;(3) Substitute the selected fitting parameters into the formulae,based on their mathematical models for the thickness of ground cover layer,or the equivalent shear wave velocity of soil-layers,or the depth of reflective wave,then the thickness of ground covering layer,equivalent shear wave velocity,and depth of reflective wave are obtained.  相似文献   

13.
土层结构对地表加速度峰值的影响   总被引:20,自引:1,他引:20  
本文在研究我国数百个工程场地钻孔资料的基础上,选取和构造了若干有代表性的典型场地剖面,利用目前工程上广泛应用的场地地震反应分析的一维等效线性化波动方法,计算了不同场地在三种不同强度的地震动输入下的地表加速度峰值反应。分析研究了覆盖层厚度、软土层的埋深与厚度等对场地地表加速度峰值的影响,得到了一些有意义的结论。  相似文献   

14.
断层场地地震动分析   总被引:20,自引:1,他引:20  
本文根据断层岩性、倾角、破碎带宽度和隐伏断裂上部覆盖层厚度等因素的变化,密切结合断层及其附近的地形地貌、土层剖面以及基岩面的起伏变化特点建立断层场地模型,并以合成人工地震动作为输入,对这些模型进行了二维地震分析计算,给出了各模型输出点地震动时程和反应谱,对计算结果进行了综合对比分析,取得了若干认识。此外,用宏观震害经验检验了本文方法的可行性和计算结果的可靠性。  相似文献   

15.
This paper presents the effects of impedance contrast (IC) across the basin edge, velocity contrast between the basin and underlying bedrock, Poisson’s ratio and soil thickness on the characteristics of basin-transduced Rayleigh (BTR) waves and associated differential ground motion (DGM). Analysis of simulated results for a two-dimensional (2D) basin revealed complex mode transformation of Rayleigh waves after entering the basin. Excellent correlation of frequencies corresponding to different spectral ratio peaks in ellipticity curves of BTR waves and spectral amplification peaks was obtained. However, such correlation was not observed between values of peaks in ellipticity curves and spectral amplification at the corresponding frequencies. An increase of spectral amplification with IC was obtained. The largest spectral amplification was more than twice the IC in the horizontal component and more than the IC in the vertical component in the case of large and same impedance contrast for P- and S-waves. It was concluded that the frequency corresponding to the largest spectral amplification was greater than the fundamental frequency of soil by around 14% and 44% in the vertical and horizontal components, respectively. Spectral amplification of the vertical component was negligible when soil thickness was less than around 15–20 times the S-wave wavelength in the basin. The largest values of peak ground displacement (PGD) and peak differential ground motion (PDGM) were obtained very near the basin edge, and their values with offset from the edge were strongly dependent on the IC across the basin edge, Poisson’s ratio, velocity contrast between the basin and underlying bedrock (dispersion), damping and soil thickness. The obtained value of PDGM for a span of 50 m in the horizontal and vertical components due to the BTR wave was of the order of 0.75 × 10?3 and 1.32 × 10?3 for unit amplitude (1.0 cm) in the horizontal component of the Rayleigh wave at rock very near the basin edge.  相似文献   

16.
云南通海盆地的浅层速度结构   总被引:3,自引:3,他引:0       下载免费PDF全文
为了研究通海盆地的地震动场地效应,在强地面运动的数值模拟计算中需要提供该地区的浅层速度结构模型.为此,在通海盆地开展了10 km高分辨率反射地震勘探和30个测点的面波联合勘探工作.综合本次探测结果与褐煤普查中的电测深和钻孔资料,得到了通海盆地的基岩埋深分布图.结果表明,在通海盆地中部,新生界厚度为100~300 m,整体表现出西南厚东北薄的趋势,盆地沉积层厚度变化明显受到小江断裂南段分支断裂的控制.浅层速度随深度分布表现出在深度相同的情况下,盆地边缘的速度高于盆地中部.  相似文献   

17.
强震动观测是获取地震地面运动最基本的手段,但其观测质量会受到观测台站周边环境的影响。本文针对不同场地条件的观测台站和附近不同高度建筑物,开展建筑物对观测场地地震动影响的模拟分析,探讨其对强震动观测的影响规律。基于ABAQUS有限元分析软件以及粘弹性边界方法,建立了8个场地-建筑物体系计算模型,分别考虑了4种不同剪切波速的场地和4种不同层数的框架结构建筑物,计算分析了建筑物高度、观测点与建筑之间的距离对强震动观测及场地土波速变化的影响。结果表明:强震动台站附近地面建筑物的存在对观测结果将产生明显的影响,近距离建筑物影响的相对误差可高达20%以上;建筑物高度的变化并没有明显改变其影响程度和影响较大的地震动周期范围,但较高建筑物的影响程度会随距离增加衰减速度减慢;场地土越软,周边建筑物对观测带来的影响越大。建议:对于较软弱场地(土层平均剪切波速低至210m/s),强震动台站避让建筑物的距离应不小于40m,对于较坚硬场地(土层平均剪切波速大于250m/s),强震动台站避让建筑物的距离应不小于25m。同时还认为,如果强震动观测要求较高精度,需进一步增加避让距离,且应具体考虑建筑物高度等因素的影响。  相似文献   

18.
不同的地震动输入面对地震反应分析结果的影响   总被引:2,自引:2,他引:0  
利用目前工程抗震设防上广泛应用的土层地震反应计算分析软件,对成都某典型卵石场地剖面进行了计算,得到了不同输入地震强度下的地震反应分析结果随不同地震动输入面的变化规律。结果表明,无论是地表加速度峰值,还是反应谱特征周期,在相同的地震动强度输入下,均是随着地震动输入面的变深而增大,其中加速度峰值最大增加20%以上,反应谱特征周期最大增加10%以上。此结论可为工程抗震设计人员获得科学合理的结构设计提供参考。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号